Zimmerei Schaufuß

Condition: reconditioned (used), Year of construction: 2017, functionality: fully functional, input voltage: 380 V, workpiece height (max.): 60 mm, edge thickness (max.): 8 mm, actuation type: electric, total height: 1,774 mm, total length: 4,580 mm, overall weight: 1,450 kg, Equipment: CE marking, documentation/manual, Workpiece thickness for edgebanding: between 8 and 60 mm, Edge thickness up to 8 mm depending on the unit Configuration: -calibrating, -edge feeding, -glue application, -end trimming, -milling group; flat or profile milling of upper or lower edges, -profile milling unit, -scraping group, -polishing station Pressure beam, feed stop, control panel Year: 2017 Fodoytp Hrepfx Adaofw

Condition: used, Year of construction: 2013, Used machine Year of manufacture: 2013 Equipment/features: - Machine table with 13 running rollers for improved workpiece guidance - Edge feed, synchronized with the belt feed Ffsdpfx Adjytkiuoaow - Edge thickness adjustable via digital counter - Pneumatic roller separation with cutter (for cuttable edges) - Three pressure rollers - Belt feed motor 0.25 kW; approx. 1250 mm length; feed rate approx. 6.0 m/min; 50 mm wide timing belt with thick, workpiece-friendly rubber coating. Digital counter for height adjustment - Direct glue application to the workpiece: leakproof glue pot with glue supply from below and fast heat-up time after machine stoppage - Flush trimming unit for front and rear workpiece edges, automatic sensing at the workpiece, pneumatic trimming with a cutter for cuttable edges - Flush milling unit with vertical sensing and horizontal guidance, reproducible adjustment via digital counters, 2 high-performance 0.4 kW high-frequency motors, continuously adjustable from 4000 to 18000 rpm, cutter diameter 70 mm, Z4, radius 2 mm/15°; central extraction connection Ø 100 mm, 2 chip extraction hoods with hose Ø 60 mm - Automatic height adjustment of the upper cutter with the belt feed - Continuous workpiece support approx. 1800 mm long, workpiece support rail extendable by approx. 300 mm - Rotatable film disc Ø 800 mm Technical details: - Minimum workpiece width: approx. 80 mm - Workpiece thickness: 10 – 50 mm - Minimum workpiece length: approx. 220 mm - Edge thickness: 0.4 – 2.0 mm - Roller separation max.: 1.0 x 55 mm, 2 x 45 mm - Glue pot heating power: 2.7 kW - Electrical connection: 400V, 50 Hz, 3Ph + N - Total connected load: 3.8 kW - Heat-up time: approx. 10 minutes - Pneumatic connection: 6 bar - Working height: approx. 880 mm - Dimensions: approx. 1800 x 700 x 1300 mm (without film disc Ø 800) - Net weight: approx. 260 kg Availability: short-term Location: Flörsheim

Condition: excellent (used), Year of construction: 2012, machine/vehicle number: AH/115881, functionality: fully functional, overall weight: 2,364 kg, Equipment: documentation/manual, Element thickness: 60 mm Edge thickness: 8 mm Fodpfjytkczox Adaofw Feed speed: 18 m/min Soundproof cabin: Yes Glue tank: Yes Touchscreen control (10 inches) Height adjusted manually from the control panel 4-axis milling machine, manually operated from the panel Cross cutting Two wrapping units, profile scraper

Condition: excellent (used), Year of construction: 2017, I sell the fully equipped edge banding machine BRANDT KDF 230 AirTec, year 2017: Configuration: Ffsdpfxoythxms Adasw Entry fence manual adjustable Premilling manual adjustable Edge banding EVA glue / PUR glue possible / AirTec unit Material pressure zone manual adjustable End cutting saws pneumatic adjustable Tilting radius milling top + bottom manual adjustable Corner rounding 1-motor manual adjustable Radius R2 scrapers pneumatic adjustable ( set of R1 included) Control panel Working thickness adjustment manually Material height 8-60mm Edge thickness 0,4-3mm Feeding speed 10m/min. Total length including feeding plate 5070mm Very good condition, fully working! Including full documentation and CE. Available immediately.

Condition: ready for operation (used), Year of construction: 2006, Edgebander manufactured in 2006. This HOMAG Optimat KAL 330 features a flexible production layout for furniture parts, accommodating workpiece dimensions from 250 to 3000 mm in length and 120 to 1200 mm in width. It includes a single-sided edge banding machine capable of processing various edge materials up to 20 mm thickness. If you are looking to get high-quality edge processing capabilities, consider the HOMAG Optimat KAL 330 edgebander we have for sale. Contact us for further details. • Line workpiece capacity: • Length 250–3000 mm • Width 120–1200 mm • Thickness 8–60 mm • Edge bander (KAL 330) — base and transport • Continuous machine base; workpiece support with roller bar extendable ~800 mm • Transport chain 80 mm wide with rubber surface; precision guidance, hardened surfaces • Top pressure: driven belt • Technical data: • Feed speed 18–25 m/min • Working height 950 mm • Minimum working width: 55 mm at 22 mm thickness; 100 mm at 60 mm thickness (depending on workpiece length) • Workpiece overhang/supernatant 30 mm • Workpiece thickness 12–60 mm • Edge material from strip: 0.4–20 mm (max cross-section 900 mm²) • Edge material from coil: 0.3–3 mm (max cross-section: PVC 135 mm², veneer 100 mm²) • Max coil diameter 830 mm • Pneumatic connection 7–8 bar • Infeed system and controls (integrated with KAL 330) • Flexible workpiece infeed system wz10 for automatic infeed (lengthwise and crosswise); for precisely sized, square parts • Stepless infeed guidance adjustment (axis), speed set at input terminal • Automatic side adjustment of units (workpiece overhang 30–80 mm) for gluing and post-processing • Input terminal; solvent applicator top/bottom • Edge preparation and gluing • Pre-milling unit: 2 motors, each 4 kW, 150 Hz, 9000 rpm; electro-pneumatic control • Stepless vertical axis SF20 for automatic centering to panel thickness • Pre-melting unit with granule storage • Quick-lock system for QA/QE application unit; QA front glue storage for color change • Basic gluing unit A20; magazine height adjustment ±5 mm (manual spindle) • Extended magazine A6/A-E12/A20 for 2 coils (max Ø 830 mm); preheating station for QA/QE • Automatic pressure zone adjustment • Trimming and milling • Trimming unit HL84 with standing trimming stop for sensitive edges • Pneumatic trimming motor adjustment (2 positions: flush/level and with overhang for contour milling) Fedpfx Ajytf Irjdasfw • Pneumatic chamfer/straight changeover; manual side trimming stop adjustment when edge thickness changes • Rough milling unit: 2 motors stacked, each 1.5 kW, 200 Hz, 12,000 rpm; height adjustment via top pressure • Pneumatic 2-position setting: roughing with ~0.2 mm overhang / without overhang • Reserved free space for a fine milling unit • Contour milling unit Servo FK13 automatic: • 2 motors each 0.4 kW, 200 Hz, 12,000 rpm • Servo-controlled movements; automatic 8-fold tool changer • Feed speed max 20 m/min; minimum spacing between workpieces 500 mm • Workpiece thickness 12–60 mm • Automatic FK adjustment for identical radii on different edge thicknesses; auto retract • FK workpiece guidance with additional clamping for min part length 120 mm (single-sided) • Finishing and cleaning • Multi cleaning unit MN21 automatic: • Up to 3 profiles; tracing from top/bottom/side for chamfer and rounding on pre-milled PVC edges • Electropneumatic air nozzles; automatic chamfer/radius changeover; auto retract of upper/lower tool • Height adjustment via top pressure • PVC shavings separator top/bottom

Condition: good (used), Code: 0367 Brand: SCM Model: BASIC 1 Automatic edge bander for wood edges, Pvc, melamine, Abs Technical data: Working height mm 8 - 40 Banding material thickness mm 0.4 - 3 Feed speed 8 mt/min Min. panel length mm 140 Ffjdjytfnfjpfx Adasw Min. panel width mm 60 End cutting unit : Rotation speed rpm 10000 - Motor power Kw 0,6 End trimming unit: Rotation speed rpm 27000 - Motor power Kw 0.5 - Tilt of cutters 12 degrees Working pressure Atm 6 Overall dimensions: mm 1700 x 700 x 1250 h Weight kg 470

Condition: excellent (used), Working area: 225 cm x 120 cm Fjdeytdhdepfx Adaefw golden shelves

Condition: used, Year of construction: 2002, functionality: fully functional, - Machine for complete processing and solid wood edge gluing up to 25 mm - Heavy-duty machine weighing approximately 3,000 kg - Still in operation and fully functional - Overall length approx. 8,100 mm Ffjdpfoytcqwox Adasw For a detailed description, please see the attachment, model UNImatic 25.7-F!

Condition: excellent (used), Year of construction: 2009, functionality: fully functional, Brandt KDF 430C edge banding machine for sale in very good condition! EDGE THICKNESS: 0.4-8 mm WORKPIECE THICKNESS: 8-60 mm with motorized height adjustment FEED RATE: 11 m/min TOTAL LENGTH: 4770 mm Radius scraper with pneumatic adjustment Fsdpfx Aoytb Smjdajfw Surface scraper Buffing unit

Condition: excellent (used), Edgebander ME35TR Pre-milling cutters, Plate pre-heating lamp Glue application by roller, Glue pot with exchange function Pneumatic pre-cut guillotine, Pressure rollers, Combination unit featuring: - flush trimming - corner rounding Top/bottom milling unit R1 – R2, Profile scraper Fjdpjytbuuefx Adaofw Flat scraper, Machine length 320 cm, Feed speed 7 m/min, Max workpiece height 50 mm, Max edge thickness 3 mm, Used machine, condition very close to new Only 1600 m processed

Condition: used, Year of construction: 2005, machine/vehicle number: 0-261-06-3662, functionality: fully functional, operating hours: 6,635 h, power: 16.2 kW (22.03 HP), input voltage: 24 V, input current: 35 A, workpiece height (max.): 60 mm, edge thickness (max.): 12 mm, actuation type: electric, We offer this used Brandt KDF-670 edge banding machine, year of manufacture 2005. Technical specifications: Manufacturer: Brandt Kantentechnik GmbH Model: Brandt KDF 670 Year: 2005 Workpiece height: approx. 8 – 60 mm Edge thickness: approx. 0.4 – 8 mm (depending on material) Feed speed: approx. 11 m/min Glue system: Hot-melt adhesive (EVA) Edge material: ABS, PVC, melamine, veneer, solid wood strips Operation: Control panel on the machine Aggregate equipment: Ffjdpfx Adoyr S Ensaew - Jointing unit - Glue application with gluepot - Pressure section with multiple pressure rollers - End trimming unit (front / rear) - Flush trimming unit - Radius trimming unit - Scraper unit (radius / flat) - Buffing unit Condition: Used machine Fully functional, with age- and use-related signs of wear Other information: Machine inspection under power possible by appointment Loading possible by arrangement. If you have any questions or require further information, please do not hesitate to contact us by message or phone.

Condition: good (used), Year of construction: 2016, functionality: fully functional, Used edge banding machine SCM - Model: Olimpic K360 T-ER1 - Very good condition. - Immediately available - Video on request Fsdsyrr Naopfx Adaefw - Year of manufacture: 2016 - High-end configuration (2 extra glue pots)

Condition: excellent (used), CATALOG NO. 7920 TECHNICAL DATA Equipment: - Disc - Tape feeder - Guillotine - Glue tank (granulate) - 2 pressure rollers - Cutting unit – guillotine - 2 milling units for edge profiling - 2 scrapers – for removing excess glue - Minimum length of workpiece: 210mm - Minimum width of workpiece: 70mm - Thickness of workpiece for edgebanding: 8-45mm - Edge tape thickness: 0.4-2mm - Support extension from table Fjdpfx Ajyrryfsdaefw - Feed motor: 0.25kW - Total power: 5.5kW - Extraction port diameter: 115mm - Dimensions (L/W/H): 2100x670x1320mm – Weight: 276kg ADVANTAGES – Unpainted – Austrian production – Very good condition – Documentation (DTR) – Used edgebander Net price: 14,900 PLN Net price: 3,550 EUR (at exchange rate of 4.2 EUR) (Prices may vary with higher fluctuations)

Condition: good (used), Year of construction: 2021, Used edgebander SCM Olimpic K360 - 11 m/min - 8 - 60 mm panel thickness - 0.4 - 6 mm edge thickness - machine length approx. 4,200 mm - weight approx. 1,200 kg Ffodpfx Adsyrrpmeajw - immediately available - few operating hours/metres (see photo) If you have any questions, please let us know.

Condition: used, Edgebander Holzher Streamer 1057 Pre-milling cutters Glue application, GLUE JET cartridge system Suitable for PUR glue Equipped with glue discharge Pneumatic pre-cut guillotine Pressure rollers Final trimming saws adjustable at an angle Top and bottom milling units R1, R2 Corner rounding unit Profile scraper Flat scraper Max edge height mm: 60 Max edge thickness in roll mm: 3 Feed speed 10m/min Comes with fluids Polishing unit Fsdpfx Aeyrq Eaedaefw

Condition: ready for operation (used), Year of construction: 2016, Numerically adjustable infeed fence Air flotation infeed table Anti-adhesive liquid spray system Pre-milling unit with diamond cutters Edge feeder for edge banding from coil or strips Glue station for GlueJet cartridges or L-Tronic laser technology 4 pressure rollers with pneumatic pressure adjustment Edge lubricant spray system Dual-motor precision end trimming unit with pneumatic angle adjustment Top and bottom edge surplus trimming unit (straight trimming) Numerically adjustable profile edge milling unit Flat scraper Profile scraper – two profiles Cleaning liquid spray system Pneumatically activated buffing units Pneumatically activated edge buffing unit Feed speed continuously adjustable from 10 to 25 m/min Automatic lubrication of the feed chain Frame support Minimum workpiece length: 140 mm Fodsyrniiepfx Adaefw Workpiece thickness: 8–60 mm Minimum workpiece width: 60 mm Year of manufacture: 2016

Condition: good (used), Year of construction: 2007, EDGEBANDING MACHINE WITH JOINTING AND COPY MILLING; RELEASE AGENT APPLICATION, MACHINE USED FOR PUR GLUING^ Technical Data: Workpiece thickness: 8 - 50 mm Edge thickness: * Fixed lengths: 0.4 - 8.0 mm * Coil material: 0.4 - 3.0 mm (max. 0.8 x 55 mm or 3 x 45 mm) Feed rate: 11 m/min Electrics: 400 V, 50 Hz, 3 Ph. Equipment: Adjustable infeed fence Centrally adjustable overhead pressure Central manual chain track lubrication Control panel at machine infeed Release agent application Jointing unit: 2 x 2.2 kW 1 clockwise, 1 counterclockwise Max. material removal: 3 mm Gluing station with clockwise and counterclockwise operation Ffedpfxjyrfh Ne Adasw 1 main pressure roller and 2 post-pressure rollers End trimming unit: 2 x 0.18 kW Pulling cut for high precision Pneumatic adjustment for straight and chamfer cutting via program Flush milling unit: 2 x 0.55 kW With vertical and horizontal tracing 2 working positions selectable via program: flush and radius milling, all axis adjustments with digital counters for quick setup Profile milling unit: 2 x 0.35 kW For profile milling of edge corners Max. edge thickness: 3 mm Max. workpiece thickness: 55 mm With pneumatic 2-point adjustment for chamfer/radius Scraper unit with quick-change heads Tracing above, below, and laterally With 2 additional quick-change heads Glue line scraper device, Pneumatically controlled Tracing above and below Cleaning agent application Buffing unit: 2 x 0.09 kW With cleaning agent application Control system: POWER CONTROL PC 20 +

Condition: used, Year of construction: 1995, Used machine Year of manufacture: 1995 Condition: unchecked Equipment and technical data: - Edgebanding thickness: 0.3-5 mm - Workpiece thickness: 6-45 mm - Minimum workpiece width: 60 mm - Minimum edge length: 200 mm - Feed rate: 11 m/min - Electrical connected load: 3.4 kW - Extraction port: 100 mm - Air requirement: 550 m³/h - Glue system: cartridge 1906 - Trim saws, front and rear: 1975 - Radius milling unit, top and bottom: 1942M - Radius scraper, top and bottom: 1929 Ffedjyq T Inspfx Adajw - Buffing unit: 1941 K - Machine length: 3675 mm - Machine width: 1470 mm - Machine height: 1200 mm Weight: 950 kg Availability: short-term Location: 63934 Röllbach

Condition: excellent (used), SCM S12 SW Industrial Thickness Planer – Made in Italy For sale: SCM S12 SW industrial thickness planer, manufactured by SCM Group (Italy). Heavy-duty professional woodworking machine, suitable for carpentry workshops and furniture manufacturing. SCM machines are renowned for their durability, precision, and robust industrial design. Technical specifications Model: SCM S12 SW Working width: approx. 520 mm Max working height: approx. 240 mm Power supply: 380 V / 3 Phase / 50 Hz Cutterhead: 4 knives Ffedpjyq Razsfx Adaow Automatic feed system Year: 1990 Made in Italy Condition The machine is in good working condition and ready for use. Suitable for Carpentry workshops Furniture production Industrial woodworking

Condition: not inspected (used), Year of construction: 2005, functionality: unexamined, workpiece height (max.): 40 mm, edge thickness (max.): 3 mm, feed rate X-axis: 35 m/min, rotational speed (max.): 12,000 rpm, number of slots in tool magazine: 48, TECHNICAL DETAILS Panel height min.: 10 mm Panel height max.: 40 mm Edge thickness min.: 0.4 mm Edge thickness max.: 3 mm Fodpfoyqybusx Adaefw Feed speed max.: 35 m/min PROCESSING UNITS Pre-milling unit Automatic engagement 48 tool positions End trimming unit 2 motors Fine trimming unit 1 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Fine trimming unit 2 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Edge scraping unit Glue scraping unit Polishing unit 2 motors Spraying device MACHINE DETAILS Control system: PC 22 EQUIPMENT Pressure applied with rubber belt Panel guides with NC positioning Glue pot for EVA hot-melt adhesive Pre-melter for EVA hot-melt adhesive Laser system (Model: LaserTec) Roller set for edge pressing with 5 pressure rollers Units mounted on safety guards CE marking The machine is sold and delivered in its actual and legal condition (“as seen and approved”), based on photo documentation and technical/commercial descriptive documentation. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 5321

Condition: not inspected (used), Year of construction: 2007, functionality: unexamined, working width: 1,935 mm, number of spindles: 40, plate height: 350 mm, working length: 6,200 mm, number of axes: 4, TECHNICAL DETAILS Working area X-axis: 6,200 mm Working area Y-axis: 1,935 mm Maximum panel thickness: 350 mm Number of edge tape magazines: 3 Ffsdpoyqx U Hefx Adajw Number of tool positions in tool magazine: 22 (located at the rear of the machine) Drilling spindles Spindles for vertical drilling: 28 Spindles for horizontal drilling in X direction: 4 Spindles for horizontal drilling in Y direction: 8 Total number of vertical + horizontal spindles: 40 Milling spindles Number of controlled axes: 4 Motor power: 10.5 kW Automatic tool changer MACHINE DETAILS Total connected load: 31 kW EQUIPMENT Suction cups for securing the workpiece Safety mats at the front Vacuum pump Waste chip conveyor Fixed groove unit for slotting in X direction The machine is sold and delivered in its actual and legal condition (“as seen and approved”) on the basis of photographic documentation and descriptive technical/commercial documents. The buyer has the right to inspect the item prior to collection and assumes responsibility for installation, securing, and operation of the machine at the place of destination. External reference: 8105

Condition: used, Year of construction: 2008, Used machine Year of manufacture: 2008 Fedpfeyqanbjx Adaefw Features and technical specifications: - Round pot glue application unit - With second glue application unit for PUR processing - Feed unit with automatic edge band magazine - Pressure zone with multiple pressure rollers - End trimming: 2 motorized saw units for front/end cap cutting - Top/bottom milling units: 2 milling units with tracing wheels for radius or chamfering - Radius scraper blade: pneumatically operated, post-processing of radii - Surface scraper blade: for smoothing the edge surfaces - Polishing unit: 2 polishing wheels with motors for final finishing - Riepe spray device - Control: PLC with control panel - Feed frequency inverter replaced by Ott in 2022 - Feed speed approx. 10–12 m/min - Workpiece thickness up to 52 mm - Edge thickness 0.3 – 12 mm - Power supply 3x 400 V AC, 50 Hz - Rated power 12.7 kW - Rated current 30.5 A - Control voltage 24 V DC - Max. fuse protection 35 A (5x 6 mm² connection cable) Machine dimensions: approx. 6120 x 840 x 1385 mm Machine weight: approx. 3,000 kg Availability: short notice Location: Röllbach

Condition: good (used), Code: 0316 Brand: HIRZT - ITALY Model: MIREA - CE Standard Automatic edge bander with hot melt glue for panels, furniture, custom-made furnishings, wooden doors, kitchens, bathroom furniture and various - CE Standard Technical data: Glue application on the panel Panel height 10/50 mm Max edge thickness 1 mm Minimum panel dimensions 70 x 140 mm Ffedsypm Tujpfx Adasw Automatic feed with belt drive - Feed speed 4 mt/min Power consumption 4 Kw Copying trimming unit: cutters mm 70 x 14 x 12 Z4 15 degrees Knife end trimming unit Extendable front support - Inlet extension - Worktable height 900 mm Overall dimensions mm 1900 x 1100 x 1250 h Weight kg 300

Condition: excellent (used), Year of construction: 2020, Homag Edgeteq S-200 Year: 2020 Specification: Feed Speed 11m/min Machine Length 4605mm Workpiece Thickness max 60mm Edge Material Roll 0-3-3mm Ffodpfxoypm Hhj Adajw Edge Material Strips 0.4-5mm Joint trimming / pre-milling (44mm high blocks) Standard EVA glue unit Pressure zone with 1 main pressure roller + 2 idel rollers with pneumatic adjustment for thickness End Trim unit with pneumatic adjustment for chamfer / straight Top and bottom trimming unit with 2mm cutters Contour trimming unit with 2mm cutters Profile scraping with pneumatic adjustment with 2mm blades Additional changeable scraping heads with 1mm blades Glue Joint scraper Buffers LED indoor lighting Control system easy touch Package for construction elements Basic v Package Central Lubrication 400V 50Hz CE

Condition: excellent (used), Year of construction: 2019, Specification 2 tanks 1 cleaning station Suitable for right sided machine such as Edgeteq S-240, S-300 and S-380 400V 50Hz Ffodpjypm Dgofx Adaew