Diesel Forklift

Kalmar DCE160-6

Condition: ready for operation (used), approx. 120 pieces = 480 running meters of safety conductor rails Number of conductors / number of poles: 5 Fpsdpsd Hurbjfx Adrsk in standard lengths of: 4 m Busbar cross section: 10 mm² for mains voltage up to: 500 V Load capacity at 100% ED: 60 A Weight per meter: 2.1 kg

Condition: used, Cut To Length CTL 2000x8, made by BRONX Strip width: 600 - 2.000 mm Strip Thickness: 2 - 8 mm Fpodjymclbjpfx Adrek Coil max. weight: 30 Tn Coil Outer Diameter: Up to 2.100 mm Coil Inner Diameter: 508mm - 610mm - 762mm with filler segments Sheet Length Stacker: 600 - 8.000 mm Stacking Capacity: 1 x 8000mm long x 2000mm wide packs Stacking: 10000kg maximum uniformly distributed over 5000mm sheet length Pack Height: 750 mm Max. speed: 60 m/min

Condition: excellent (used), Year of construction: 1994, total length: 2,950 mm, total width: 2,100 mm, feed length X-axis: 650 mm, feed length Y-axis: 400 mm, feed length Z-axis: 400 mm, workpiece weight (max.): 400 kg, feed rate X-axis: 5,000 m/min, feed rate Z-axis: 5,000 m/min, grinding wheel diameter: 350 mm, table length: 600 mm, table width: 400 mm, Digital read out system position slides 5 stones and flanches Fodpfx Aeyvhxmedrspk Coolant and Filtration system CE Mark Levelling pads included  Full set off books  X - Travel: 650mm Y - Travel: 400mm Z - Travel: 400mm Table Length: 600mm Table Width: 400mm Table load: 400 Feed rate X-Axis: 0-5000mm/min. Feed rate Z-Axis: 0-5000mm/min. Grinding stone dimensions:350 x 127 x 50mm Power: 6kW Speeds: 1400Rpm Cooling system: Yes Feed rate Y-Axis: 0-5000mm/min. Length: 2950mm Width: 2100mm Height: 2000mm Weight: 2550kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, functionality: fully functional, machine/vehicle number: T331051593, Year of construction: 2006, operating hours: 5,323 h, load capacity: 16,000 kg, lifting height: 3,980 mm, fuel type: diesel, mast type: simplex, construction height: 3,920 mm, power: 147 kW (199.86 HP), fork carriage width: 2,950 mm, fork length: 2,400 mm, empty load weight: 24,300 kg, drive type: Diesel, construction width: 2,950 mm, Heavy-duty forklift - diesel Chassis number: T331051593 Load center: 1200 Fork width: 250 mm Fodpfoyy Effex Adropk Fork thickness: 100 mm ISO class: Terminal West Mast type: Standard Transmission: Dana Clark 342TE13310-20 Condition: Operational and fully functional Technical condition: Good Front tires type: Pneumatic Front tires size: 12.00-20 Front tires condition: 40 - 60% Rear tires type: Pneumatic Rear tires size: 12.00-20 Rear tires condition: 20 - 40% Description: Overhauled transmission with warranty (repaired for €17,000.00) 2,950 mm wide fork carriage Side shifter, fork positioner, 3rd valve, 4th valve, front work lights, heater, fully enclosed cab,

Year of construction: 1990, condition: good (used), coil weight: max. 15 t Fpedpfebibu Tjx Adrek coil OD: max. 1.800 mm

Year of construction: 2018, condition: refurbished (used), Flying cutoff unit TCC 120/168, made by OTO MILLS Recently revamped Complete flying cutoff unit including: - Accelerator (carriage transmission) - Main carriage motor - Cutoff unit TCC120 with base with linear guides, cutting head, clamping unit and support for tube at exit side Fpodpfsvtpp Nex Adrok - Control panel RENEWED - Electrical cabinet RENEWED - Hydraulic group - Cable chain - All existing documentation, manuals, drawings Specifications: - Type of saw : Friction - Material thickness : 1 –6 mm - Standard tube length : 3 –12 m - Diameter range : 42 –168 mm - Square tubes : 40x40 –130x130 - Rectangular tube : 50x30 –180x80 - Max. speed : 120 m/min - Length tolerance : +/-2 mm Round tube diameter: 42 – 168 mm Square tube diameter: 40×40 – 130×130 mm Rectangular tube diameter: 50×30 – 180×80 mm Material thickness: 1 – 6 mm Tube length: 3 – 12 m Type of saw: Friction Length tolerance: +/-2 mm Max. speed: 120 m/min

Year of construction: 2026, condition: refurbished (used), LINEAR CAGE FORMING TUBE MILL VAI 89.5(6) with universal CTA forming REVAMPED AS NEW Specifications: - Manufacturer: VAI Voest Alpine Industrieanlagenbau - Round tube diameter: 33.7 - 88,9 mm - Square tube: 30x30 - 70x70 mm - Rectangular tube: 40x20 - 100x40 mm - Thickness: 0.8 – 5.0 mm (6.0mm with S235J2) - Speed: 100 m/min Complete line with: - Double expandable mandrel with PEELER OTO AD408 SD - Strip entry line with strip opener, driven pinch-roll, pre-leveller and lateral guiding rolls - Automatic strip joiner - Intermediate strip guding stand - Break down section - Forming section : Universal CTA Forming section VAI CTA90 - Fin pass section - Welding section - Double Cooling tunnel - Sizing section - Off-Line sizing stands - Turk-head section - Motorised Exit roller conveyor Fpjdpey Uhxkefx Adrsk Scope of supply: 1. Double expandable mandrel with PEELER OTO AD408 SD - Strip width 500mm - Hydraulic expansion - Snubber roll top/bottom - 8 Tn/arm - Pneumatic servocontrolled brake 2. Strip peeler - Strip opener 3. Strip Guiding 4. Break down section - 2 motorised stands - Monoblock casted stands - Hydraulic gauge compensation and quick setup - Shaft diameter 89mm - Mechanical SIKO indicator - Total installed power 106 kW 5. Forming section - Universal CTA Forming section VAI CTA90 6. Fin pass section - 2 motorised FP with rafted quick change - Monoblock casted stands - Hydraulic gauge compensation and quick setup - Shaft diameter 89mm - Mechanical SIKO indicator - Total installed power 106 kW 7. Welding section - 4-roll configuration - Heavy duty welding head with lateral and top adjustment 8. Double Cooling tunnel - 2 x 4000mm With V-rollers support 9. Sizing section - 4 motorised sizing cages - Total installed power 260kW - With quick-change rafted stands - SIKO bottom and top indicators 10. Off-Line sizing stands - 4 motorised sizing cages - Total installed power 260kW - With quick-change rafted stands - SIKO bottom and top indicators 11. Turk-head section - 3 turk-heads - Heavy duty changing plates 12. Complete set of rolls Round tube diameter: 33.7 - 88,9 mm Square tube diameter: 30x30 - 70x70 mm Rectangular tube diameter: 40x20 - 100x40 mm Thickness: 0.8 – 5.0 mm (6.0mm with S235J2) Speed: 100 m/min

Condition: used, Year of construction: 2000, functionality: limited functionality, overall weight: 3,000 kg, total length: 1,500 mm, total width: 700 mm, total height: 600 mm, input voltage: 380 V, type of input current: three-phase, year of last overhaul: 2010, Joint Strip Oto Mills (strip splicer), equipment suitable for splicing strips at the entry of the rollformer accumulator. Fodpfx Aoxmaa Ijdropk

Condition: good (used), machine/vehicle number: 3375, Year of construction: 2007, load capacity: 15,000 kg, lifting height: 4,000 mm, mast type: duplex, fork carriage width: 280 mm, fork length: 2,200 mm, total length: 5,250 mm, total width: 2,950 mm, operation weight: 24,180 kg, additional equipment features: Front mud guards, Warning triangle, Centralized greasing system, Equipment: lighting, Kalmar DCE150-12 from Uniktruck Wheel type – Drive wheel: Wheel type – Steering wheel: Pneumatic Fedpfx Ajyuic Nedrspk Wheel size – Drive wheel: 12.00-20 Wheel size – Steering wheel: 12.00-20

Year of construction: 2007, condition: used, THERMATOOL High Frequency Welding CFI 350 kW VF Including selectable frequency, in steps of 1kHz, range 180-300 kHz Fully revised in 2026 by Thermatool specialists Technical specifications · Input voltage: 3 x 380 V · Input current: 525 A · Welding frequency: 180 - 300 KHz · Output power: 350 kW · Auxilirary service voltage: 24Vdc · PLC Siemens S7 1. DC Power supply • SCR Power Controller/Stabilizer - Provides constant output power for consistent weld quality. • Rectifier Circuit achieving 6 pulse Rectification. • Solid State Low Ripple Filter - Reduces AC line harmonics and switching transients that can affect weld quality. • AUTOMATIC SPEED POWER CONTROL Automatic Speed Power Control - Automatically ramps power up and down in line with mill speed, minimizes scrap on stopping and starting. • PLC - Controls and monitors welder operation sequences and provides fault and running data for the Alphanumeric display 2. CFI 350KW VF Solid-state HF welder • Compact rugged enclosure - sealed and internally cooled. Provides small footprint whilst ensuring reliable performance in harsh mill environments. • Water cooled high frequency MOSFET power transistor modules – Modular design provides maximum flexibility, long equipment life and reduces time for maintenance. • AUTOMATCH Automatic Load Match – Fully automatic series and parallel load matching system which enables the welder to run at optimum efficiency with guaranteed frequency stability - Assists the tube producer in maintaining repeatability. • High frequency capacitor bank - Designed specifically for the Tube Welding application. Capacitors deliver high power with low voltage to minimize flashovers at the induction coil. • Water flow and temperature protection. • Output bus-bar system - Externally water-cooled for ease of maintenance. INCLUDING SELECTABLE FREQUENCY Selectable frequency, in steps of 1kHz, range 180-300 kHz 3. Remote control console • Display - provides operator and maintenance personnel a constant display of fault and running data for maximum productivity. Fpsdjymadbjpfx Adrsk • Power Control - Preheat and Main power potentiometers ensure precise setting of weld power and minimizes un-welded tube thus reducing scrap. • Pushbuttons and Control Switches - For safe simple operation and protection of plant personnel. Analogue Indication Meters - Provide back-up for Alpha Numeric display. 4. Closed loop cooling system • Plate Type Heat Exchanger - High efficiency reducing raw water consumption. • Stainless Steel Water Pump & Plastic Pipework • Automatic Temperature Control Valve - Maintains a constant water temperature thus avoiding condensation inside the equipment. • Header tank with Level Switch. Comprehensive equipment inspection, supervised by a Thermatool specialist. Input voltage: 3 x 380 V Input current: 525 A Welding frequency: 180 - 300 KHz Auxilirary service voltage: 24Vdc PLC: Siemens 7