Hydraulic press for paper.

American Baler CO hydrauliczna

Year of construction: 1994, condition: ready for operation (used), Motor power: 15.5kW/19.5kW, pressing force: 320kN, spec. pressure: 425kN/m², machine dimensions X/Y/Z: approx. 5700mm/1900mm/1800mm, weight: approx. 6000kg. The machine has a defect due to moisture and should be checked. Ljdoip D Rpjpfx Af Seai

Condition: used, Complete primary crusher plant LOKOMO K140 single-toggle jaw crusher, inlet: 1,400 x 1,200 mm, up to 820 t/h Including one set of unused crushing jaws Lajdpfxswcyh Hj Af Sji with feed hopper, LOKOMO B16 vibrating feeder, LOKOMO B13 discharge chute, and steel structure

Condition: ready for operation (used), Dewatering screen Sotres with Cyclone Brand: Sotres Ljdpjthy Sbsfx Af Ssai Dim. screen surface: 2800 x 1100 mm Screen opening: 12 x 1 mm with two pieces vibration motors of each 2 kW Including springs. Dim. cyclone: 3500 mm Length , Diameter 1100 mm. including steel construction incl.: tank incl.: Warman pump with e-motor , type 8/6.

Condition: excellent (used), Year of construction: 2023, operating hours: 1,851 h, functionality: fully functional, pressing force: 70 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 500 kg, overall weight: 17,000 kg, oil tank capacity: 70 l, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410 BS-22/50 Year of construction 2023 Pump operation hours 1,851 hours, as of July 24 Press power main press 70 t (a 70 tonne hydraulic cylinder is installed, special equipment) Specific press force 90,9 N/cm² (a 70 tonne hydraulic cylinder is installed, special equipment) Feed channel 1,400 x 1,000 mm Theoretic cycle time 13 sec Theoretic throughput capacity 266 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 22 kW Connected load 65 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 5,5 t/h bulk weight of 50 kg/cbm approx. 7,5 t/h bulk weight of 100 kg/cbm approx. 9,7 t/h Bale weight with a bale length of approx. 1.2 m up to 500 kg, depends on material SPS controller Siemens S7-1500 Operating panel Schneider Harmony Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 17 t Special equipment: Wear-resistant floor made of HARDOX steel Larger main hydraulic cylinder with 70 tonnes of pressing force Special press ram for pressing loose bulk materials with small grain sizes OptiCut XS system for lower cutting forces and higher throughput rates Special pressing piston for pressing "difficult" materials Technical data for the conveyor belt: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Deutschland Type KGF GB 1500 Year of construction 2023 Drive power 4.0 kW Lasdpfx Aou Thbxsf Ssi Belt speed approx. 0.3 m/second Length feeding conveyor 2,679 mm Length elevating conveyor 6,866 mm Length goose neck 1,272 mm Grade 35° Effecting width 1,400 mm Side wall height 800 mm Carrier height 50 mm Carrier distance 750 mm Belt quality EP 400/3, 3:1 (DIN quality N) Overall height 4,515 mm Overall transport dimensions11,148 x 2,502 mm (l x w) Technical data on the non-contact personal protection system: Manufacturer BOREMA Umwelttechnik AG, Switzerland Type APSS iBOR 22 Year of construction 2023 Condition of the press system: The entire system is in very good condition due to the short operating time of only 1,851 pump hours and the processing of only paper, cardboard and film. Scope of delivery: Avermann baler, type AVOS 1410 BS-22/50, incl. wire drawing stations and bale chute Avermann conveyor belt, type KGF GB 1500 BOREMA personal protection system, type APSS iBOR 22 Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 2011, operating hours: 20,580 h, functionality: fully functional, pressing force: 48 t, filling opening width: 1,020 mm, filling opening length: 1,250 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 450 kg, input current: 59 A, overall weight: 12,000 kg, transport height: 2,750 mm, oil tank capacity: 300 l, power: 30 kW (40.79 HP), transport width: 2,300 mm, transport length: 8,500 mm, tank capacity: 300 l, Good day, We hereby offer you a used baler from the manufacturer HSM, type VK 4812. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot accept any liability for correctness and completeness. Manufacturer HSM Type VK 4812 Year of manufacture 2011 Operating hours 20,580 hours Main press force 48 tonnes Drive power 30 kW Machine weight press 12 tonnes The machine documentation is available in German. A viewing is possible by appointment in our workshop. Lasdpfjt H Rcaox Af Ssi We would be delighted if this machine is of interest to you. Your service team Mertens & Frowein GmbH

Condition: good (used), Year of construction: 1975, Martin Miniline 616 - Vacuum feeders - hhs-Gluesystem with Gluecontrollsystem - Max.Speed: 24,000 Sh/h Lajdpfx Aoq Nf D Hsf Soi - Max.Size: 600x1600 mm - Year 1975/1991 - 2 Color Flexo - Slotter - Rotary die cutting - Folding gluing - Counter Ejector, Year 1991

Year of construction: 2008, operating hours: 40,000 h, condition: good (used), machine/vehicle number: HBC 140 2x75kW 2008 (00191), Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Ledpfx Afskcgf Hj Seai Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: used, Year of construction: 2014, sewing machine - siemens computer Lajdpfx Afjwwqikj Soi - gigalynx signature control - change stitch - thread separation - universe stacker plus

Year of construction: 2025, condition: new, We also offer leasing and financing options. Feel free to contact us! For all types of recycling, we have shredders and other recycling machinery in stock in Heilbronn. From copper recycling to plastic recycling, you can purchase all types of machines from us. Please don't hesitate to ask. ‼️IMMEDIATELY AVAILABLE‼️ IN STOCK‼️ Shredder for pre-shredding of cables, plastics, etc. – ALL-PURPOSE SHREDDER. ➡️Motor: 11 kW ➡️40 cm shafts ➡️380V 60 Hz 3-phase ➡️Dimensions (LxWxH): 1350x700x1600 mm ➡️Weight: approx. 800 kg Ledpep E Eiysfx Af Seai Net: €13,999.00 +19% VAT: €2,659.81 Gross: €16,658.81 Errors excepted. Images may differ.

Condition: repair required (used), Year of construction: 1987, Gyratory crusher Model 1500 fine chamber Lasdpfx Ajiuifvof Ssi Requires change axial bearings rest of machine in good condition. Can be repaired or used for spare parts. Price 1 euro per kg.