Conveyor belt Conveyor belt Crusher

die magnetprofis 2019010803

Year of construction: 2019, condition: as good as new (ex-display), Aluminum flat conveyor including 4 suspension points Pedpfx Abod Ra Tts Iogw Dim: 3000 + 520 x 105mm Conveyor belt width 400mm PVC conveyor belt incl. Studs and wave edge * optional with magnetic deflection roller at the end of the conveyor belt. * optionally with substructure * Special designs in all versions possible.

Condition: excellent (used), Year of construction: 2023, operating hours: 1,851 h, functionality: fully functional, pressing force: 70 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 500 kg, overall weight: 17,000 kg, oil tank capacity: 70 l, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410 BS-22/50 Year of construction 2023 Pump operation hours 1,851 hours, as of July 24 Press power main press 70 t (a 70 tonne hydraulic cylinder is installed, special equipment) Specific press force 90,9 N/cm² (a 70 tonne hydraulic cylinder is installed, special equipment) Feed channel 1,400 x 1,000 mm Theoretic cycle time 13 sec Theoretic throughput capacity 266 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 22 kW Connected load 65 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 5,5 t/h bulk weight of 50 kg/cbm approx. 7,5 t/h bulk weight of 100 kg/cbm approx. 9,7 t/h Bale weight with a bale length of approx. 1.2 m up to 500 kg, depends on material SPS controller Siemens S7-1500 Operating panel Schneider Harmony Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 17 t Special equipment: Wear-resistant floor made of HARDOX steel Larger main hydraulic cylinder with 70 tonnes of pressing force Special press ram for pressing loose bulk materials with small grain sizes OptiCut XS system for lower cutting forces and higher throughput rates Special pressing piston for pressing "difficult" materials Technical data for the conveyor belt: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Deutschland Type KGF GB 1500 Year of construction 2023 Drive power 4.0 kW Belt speed approx. 0.3 m/second Length feeding conveyor 2,679 mm Length elevating conveyor 6,866 mm Length goose neck 1,272 mm Grade 35° Effecting width 1,400 mm Side wall height 800 mm Carrier height 50 mm Carrier distance 750 mm Pedpfx Aou Thbxob Iogw Belt quality EP 400/3, 3:1 (DIN quality N) Overall height 4,515 mm Overall transport dimensions11,148 x 2,502 mm (l x w) Technical data on the non-contact personal protection system: Manufacturer BOREMA Umwelttechnik AG, Switzerland Type APSS iBOR 22 Year of construction 2023 Condition of the press system: The entire system is in very good condition due to the short operating time of only 1,851 pump hours and the processing of only paper, cardboard and film. Scope of delivery: Avermann baler, type AVOS 1410 BS-22/50, incl. wire drawing stations and bale chute Avermann conveyor belt, type KGF GB 1500 BOREMA personal protection system, type APSS iBOR 22 Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, Year of construction: 2024, total height: 860 mm, total length: 2,400 mm, total width: 1,200 mm, overall weight: 920 kg, height adjustment type: mechanical, Manufacturer: GERD WOLFF Technical Details: • Length 2400 mm • Width 1200 mm • Height 200 mm • Weight 920 kg • Hole diameter 28 mm • Hole spacing 100 mm • Plate thickness: 25mm Advantages and Features: • 3-day gas nitriding process • Increased corrosion resistance • Weld spatter adhesion protection • Maximum load capacity • Enhanced fatigue strength • Improved vibration resistance • Fine scale engraving • Reinforcement with welded seams and ribs on the underside Pgjdpfxsvbbqns Ab Iew • Optimal working height of 820-865 mm • 6 height-adjustable support legs • Available with a matching accessory set (optional) Our welding tables are manufactured using HT 300 cast iron and are nitrided as a whole after mechanical processing. Furthermore, they feature precise fine scale engraving using laser technology. To ensure adequate stability, our welding tables are reinforced with welded seams and ribs on the underside (see illustrations). Additionally, they undergo a 3-day gas nitriding process, enhancing their corrosion resistance, fatigue strength, and vibration resistance, among other factors. All our tables come with adjustable legs. The minimum height adjustment range is 620 mm, while the maximum is 665 mm, allowing for a variable working height of 820 to 865 mm. Additional available dimensions: • 1000 x 1000 x 200 • 2000 x 1000 x 200 • 1200 x 1200 x 200 • 1500 x 1000 x 200 • 1500 x 1500 x 200 • 1500 x 2000 x 200 • 2000 x 3000 x 200 • 3000 x 1500 x 200 • 3000 x 2000 x 200 • 4000 x 2000 x 200 Please note that the images are not to scale and are for illustrative purposes only. Our welding tables are produced for our distribution brand "GERD WOLFF Maschinenfabrik" by a reputable manufacturer. 3D Welding Table - 3D Clamping Fixtures - 3D Precision Welding Table

Condition: excellent (used), Year of construction: 1988, utomatic wide belt sander with 2 belts for varnish, wood, veneer, composite materials and various materials Technical data: Working width mm 1350 Max useful height mm 130 Belt size mm 2450 x 1350 Composition: 1° Group: Sanding roller diameter mm 320 - sh. 60 - Blowers cleaning belts - Motor Kw 11 with speed variator 2° Group: Sanding roller diameter mm 320 - sh. 40 - Blowers cleaning belts - Podpogmbu Isfx Ab Ijgw Motor Kw 11 with speed variator Scotch brite - Motor Kw 1,5 Vacuum table - Motor Kw 5,5 Feed belt speed variator 4/19 mt/min Operating pressure 7 Bar equipped with Abrasive belts series Overall dimensions: machine mm 2000 x 2700 x 2500 vacuum pump mm 800 x 700 x 900 h

Condition: new, Bunker conveyor suitable for the feeding of presses, shredding, etc.. Delivery throughout Europe possible. Technical data: POS. 1 feed hopper Pgsdpfxjdxwlqs Ab Isw POS. Task 2, vol. 1, 5kW, conveyor width: 1100 mm, axis dimensions: 3500 mm POS. Platform 3, volume 1, 1kW, conveyor width: 1100 mm, axle size: 4700 mm Standard discharge height: 2800 mm (greater than possible with distance feet as shown on the illustration) Ordering goods Further information and data upon request

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: Pgsdpfxeu Thhrj Ab Iew All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2001, condition: ready for operation (used), Max. weighing range: 1000g, with Weighing Cell Mettler Toledo TF10-L-P, display of weight values, weight classification and automatic sorting of weighed goods. Pedpfx Abetqtw Us Iogw

Condition: used, Year of construction: 2009, operating hours: 20,536 h, pressing force: 80 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, empty load weight: 16,000 kg, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Podpfx Aou Thypsb Iogw Operation hours 20,536 hours, as of September 2024 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine is currently in our workshop undergoing partial refurbishment. We expect the refurbishment work on the machine to be completed by the end of October, after which the machine will be tested and released for sale.

Condition: new, Year of construction: 2025, Cut-to-length and mitre saw type: ZS 200 N - 5 KW motor with machine stand, Machine via handwheel and worm gear (rear) Tiltable Saw blade diameter 520 mm, saw blade mounting hole 50 mm Saw blade speed: 2800 rpm 400 volt / 5 KW (S6/40%) motor with brake and automat. Star delta motor control Cutting width at 90 degrees: 420 mm Cutting width at 45 degrees: swiveled: 295 mm Cutting height at 90 degrees: 200 mm Cutting height at 45 degrees inclined: 140 mm Psdpfx Abjk H Ic Uo Iogw Saw can be swiveled on one side up to approx. 25 degrees to an acute angle and tilted flat to the left up to 30 degrees Carbide circular saw blade 520x4.0/2.8 x 50 mm 60 WZ neg. for wood RLH-ST60 6.0 mtr. measuring length, mounting side: left Cross-cut fence / roller conveyor, heavy-duty design, Stop slide adjustable from the workstation via handwheel, electronic-digital dimension display, pneumatic clamping of stop slider, stop flap folds backwards, with steel rollers 60 mm diameter, roller spacing 200 mm, 400 mm roller width, with 4 support feet and connection piece: overall length: 6.7 mtr. Surcharge for digital electronic display unit type: FIAMA EP6 for 230 V mains operation, with electric on/off switch and socket. Powerful dark red LED display. Higher accuracy than the battery-powered crystal display RO-ST60 4.0 m long feed roller conveyor Mounting side: Right Heavy-duty design, steel rollers: 60 mm Diameter, roller spacing: 200 mm 400 mm roller width, 3 support feet and connection piece Location: From stock 54634 Bitburg - immediately available - Picture: similar. Machine is still in original packaging

Condition: good (used), Year of construction: 1985, functionality: fully functional, pressing force: 50 t, bale length: 1,000 mm, bale width: 750 mm, bale height: 75,07,50,750 mm, bale weight: 500 kg, input voltage: 400 V, overall weight: 7,500 kg, oil tank capacity: 500 l, power: 30 kW (40.79 HP), empty load weight: 7,500 kg, input frequency: 50 Hz, Manufacturer: Paal Typ: Pacomat V Year of construction: 1985 Press power main press: 50 t Specific press capacity: 5 kg/cm² Feed channel: 1.000 x 720mm (l x w) Theoretic throughput rate: 200 cbm/h Bale size: 700 x 1.000 mm (w x h) length adjustable Driving motor: 30 kW Bale weight: approx. 500 kg Machine weight: approx. 8t The hydraulic unit is functional, the drive motor is in the removed state. Podpfx Aeic Rl Dob Ijgw