CNC turning and milling center

DOOSAN PUMA 700L

Condition: used, Year of construction: 2007, Technical details: x-travel: 635 mm y-travel: 460 mm Lodpjw A I Uuofx Akfjrk z-travel: 510 mm control: 3D Heidenhain i TNC 530 table-size: 790 x 560 mm table load capacity: 600 kg tool taper: SK 40 Revolution per minute: 20 - 12 000 U/min. tool changer with: 20 place spindle hours: 36.050 h operating hours - idle run: 91.000 h total power requirement: 13,9 kW Weight approx.: 3,6 t tool taper: SK 40 range of revolution per miute: 20-10.000 U/min Tool changer: 20-fach dimension machine xH: 3,0 x 2,0 x 2,15 m

Year of construction: 2000, condition: ready for operation (used), Travel X/Y/Z: 600mm/410mm/520mm, table dimensions X/Y: 840mm/420mm, spindle speed: 6000rpm, spindle power: 8.5kW, tool holder: SK40, tool positions: 22, rapid traverse X/Y/Z: 36m/36m/20m/min. Machine dimensions X/Y/Z: approx. 2200mm/2300mm/2300mm, weight: approx. 2500kg, control: Heidenhain TNC 426. An on-site inspection is possible. Lredpfx Akev Uqb Njfjk

Condition: excellent (used), Year of construction: 2002, travel distance X-axis: 1,250 mm, travel distance Y-axis: 880 mm, travel distance Z-axis: 800 mm, workpiece height (max.): 1,230 mm, workpiece diameter (max.): 1,250 mm, spindle speed (min.): 18,000 rpm, spindle speed (max.): 18,000 rpm, Heidenhain iTNC 530 control Tool changer for 60 tools Automatic head +180/-7° stepless HSK A63 Lredow Ngipopfx Akfsk Number of pallets: 2 pcs Pallet size: 1000*800 mm

Condition: good (used), functionality: fully functional, Year of construction: 1990, machine/vehicle number: 4ROLL, roller (bottom) diameter: 470 mm, roller (top) diameter: 470 mm, side roll diameter: 420 mm, roller diameter: 470 mm, roller length: 3,050 mm, working width: 3,050 mm, working height: 1,800 mm, sheet thickness (max.): 50 mm, sheet thickness steel (max.): 45 mm, sheet thickness aluminum (max.): 45 mm, sheet thickness copper (max.): 45 mm, overall weight: 43,000 kg, total length: 7,700 mm, total width: 2,410 mm, total height: 2,470 mm, power: 37 kW (50.31 HP), input voltage: 380 V, type of input current: three-phase, working length: 3,050 mm, Equipment: documentation/manual, emergency stop, PLATE BENDING MACHINE FACCIN - 4 ROLL HYDRAULIC 3000 X 40 MM Lredpfjwb Scmox Akfsk MODEL 4HCI3-35/30 YEAR 1990 PLATE BENDING ROLL LINEAR GUIDEWAYS DOUBLE PINCH PRE-BENDING Machine in good working condition Bending capacity -Plate width : 3000 mm -Rolling plate thickness 40 mm - Prebend thickness 35 mm Rolls dimensions: -Useful length 3050 mm -central rolls upper/lower 470 mm -side rolls left/right 420 mm • Hardening of the 4 rolls high strength surface • 3 rolls driven powered with gear unit with hydraulic motor • Conical bending attachment side rolls tiltable to form cones, contrast pad roller type. • Opening front hydraulic drop-end to unload the closed shell. • Variable speed working roll bending rotation hydraulic speed fast/slow. • Console electric on wheels with centralized commands joysticks and 3 digital readout. • Digital readouts of the rolls position bending and pre-bending repeatability. • Hydraulic tank capacity oil 350 liters – power electric 37 Kw voltage 380 /50 • Dimension 7700 x2410 x H 2470 mm - weight 43000kgs

Condition: good (used), Year of construction: 2012, functionality: fully functional, Control: SIEMENS Spindle bore: 65 mm Turning length: 660 mm Max. speed: 6,000 rpm Counter spindle Z= 700 mm TOOL CARRIER 1 with milling spindle Milling spindle: 7,200 rpm B-axis: 360° 14 stations with driven tools Tool speed: 7,200 rpm Travel: X= 230 / Y= ±65 / Z= 845 Ledpfxjyi Uk Io Akferk TOOL CARRIER 2 14 stations with driven tools Tool speed: 7,200 rpm Travel: X= 140 / Y= ±45 / Z= 810 Chip conveyor Filter Bar feeder INDEX MBL

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC Ljdpfx Akswp Rqfoferk • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: good (used), x-way 410 mm y-way 310 mm z-way 400 mm taper of the main spindle SK 40 table clamping surface 700 x 280 mm speed 45 - 2000 rpm quill stroke 63 mm total power requirement 2,2 kW Machine weight approx. 1300 kg space requirement approx. 2,1 x 2,1 x 1,7 m Voltage 400 V Lrjdpei Elydofx Akfsk 3-axis digital display Heidenhain Fixed angle table Coolant device Vertical milling head swiveling

Condition: good (used), Year of construction: 2012, Parts shown by hand not come. X1020mm Y610mm Z610mm 12.000 rpm,25 KW, 160Nm Control unit: HEIDENHAIN iTNC 530, 4th axis will come without parts shown by hand. Ljdpfx Ajx Awzbekfjrk

Condition: used, Year of construction: 1999, swing dia. 680 mm max. turning diameter 429 mm turning length 440 mm control MORI SEIKI - MSC-501 turning speeds 5.000 U/min max. bar material dia. 56 mm travel -x axis 233 mm travel -z axis 510 mm number of tapers in turret head 2x12 Ledpfowplulsx Akfjrk CNC Turning- and Milling Center | MORI SEIKI - ZL-150SMC equipped with main/counter spindle, c- axis, 2x turret for driven tools, bar feeder and chip conveyor. The machine is in a well-maintained condition. Please note that the technical details were added from comparable machines. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags: ZL 150SMC | ZL150SMC | ZL-150 SMC | ZL 150 SMC

Condition: reconditioned (used), functionality: fully functional, approx. 4.5 m long infeed and centering table Drive via chain from the feed motor Centers the logs in the middle of the rotor Debarking machine VK 26 4 main cutters 4 pre-cutters 30 KW main motor Lrodpfou Hmacjx Akfsk 11 KW feed unit non-driven extraction table Machine workshop checked Machine cleaned and repainted