Mobile shelf

Hordenwagen

Condition: excellent (used), Year of construction: 2023, machine/vehicle number: 0-200-87-0913, functionality: fully functional, input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, edge thickness (max.): 3 mm, height adjustment type: electric, total length: 10,825 mm, Equipment: documentation/manual, Used single-sided HOMAG edge-banding machine for straight edges – EDGETEQ S-500 For pre-milling (jointing trimming), gluing and post-processing of various kinds of edging materials. Fixed stop on the left side. Year of Manufacture: 2023 EQUIPMENT / SPECIFICATION BASIC MACHINE - with 80 mm wide conveyor chain with rubber-coated chain pads, - workpiece thickness 8 to 60 mm - top pressure with compound V-belt, automatic height adjustment (to workpiece thickness) - panel support with roller guide, extractable approx. 700 mm - glue roller drive in case of feed stop - hand switch /remote control for setup – mode - adjustable infeed fence with NC-axis (CAN-bus) - Jointing trimming 2 motors each 3 kW (clockwise, counterclockwise), jumping function GLUING SECTION V20, consisting of: - QA65 glue application unit, with PTFE-coating (Teflon), with pneumatically operated glue gates - pneumatic clamping of glue application - Pre-melter for PUR glues - Edge magazine, edge thickness min. 0,4 mm to max. 3 mm Edge width (height) max 65 mm - 2-fold automatic edge roll changing magazine - Pressure zone with automatic horizontal adjustment (NC CAN-axis) to edge thickness, 1 driven & 4 non-driven pressure rollers. POST-PROCESSING SECTION: - Snipping (end-trimming) unit PK25 horizontal, 2 motors, with straight/chamfer cutting function - Edge Trimming MS40 2x0.55 kW, top/bottom - Multifunction Corner Rounding MF60, 2 motors 0.4 kW (top/bottom) with linear motors, soft-touch - Profile (radius-) Scraping MN11, multi scraping tool, automatic positioning and adjustment (NC) Lsdpfoy D A Swsx Abyehh - Flat Scraping (glue joint) FA20, top/bottom, (version with 3 tracer rollers), automatic adjustment - Buffing Unit FP10, top/bottom Control / software: - powerControl PC 23 PowerTouch - woodCommander 5 - Edge sequence control - change-over in the gap Machine dimensions 1085 x 180 x 235 cm (with opened doors)

Condition: excellent (used), Year of construction: 2012, Used machine from business closure. GROSS shredder - Model GAZ 62 - Year of manufacture: 2012 - 18.5 kW - good condition - available immediately Lhodpex Tp U Rsfx Abysh

Condition: used, Year of construction: 2000, functionality: fully functional, table length: 810 mm, table width: 975 mm, SECOND-HAND BAND RE-SAWING MACHINE MEBER MOD. SR900 - Table dimensions mm. 975x810 - Motor Kw 11 Lhsdex Rt Aajpfx Abyeh - Year 2000 (CE)

Condition: like new (used), Year of construction: 2020, functionality: fully functional, operating hours: 146 h, power: 7.5 kW (10.20 HP), input voltage: 400 V, input current: 35 A, cutting height (max.): 204 mm, cutting width (max.): 1,300 mm, saw blade diameter: 550 mm, height adjustment type: electric, actuation type: electric, rotational speed (max.): 6,000 rpm, rotational speed (min.): 2,000 rpm, table height: 910 mm, year of last overhaul: 2026, Equipment: CE marking, documentation/manual, rotational speed infinitely variable, saw blade guard, scorer, Altendorf F 45 EvoDrive plus (total price €52,050) + Air cushion table + Laser cut line indicator Machine with only 150 operating hours, being sold at a reduced price due to restructuring of a two-person operation. - CNC parallel fence, 1300mm Ledpfx Aozbc Uxebyohh with reinforced table extension - Reinforced 7.5KW motor with VARIO speed control, 2,000 - 6,000 RPM, stepless - Extended cutting height, 204mm - 2-axis scoring saw with LED warning light in the danger area - Cross slide extension, retractable - Miter fence with DIGIT LD, cutting lengths up to 3200 mm - Reinforced extension, 840 mm - On/Off switch on the sliding carriage - Front support roller - Toolbox

Condition: ready for operation (used), Year of construction: 2015, operating hours: 1,236 h, working width: 1,100 mm, Belt sander manufactured in 2015. This Kundig Premium-1 1100K features a supply voltage of 400 V/AC and a control voltage of 24 V/DC. It operates at a current of 24.90 A and has a power rating of 12.62 kW. If you are looking to get high-quality sanding capabilities, consider the Kundig Premium-1 1100K machine we have for sale. Contact us for further details. • Supply voltage: 400 V AC • Control voltage: 24 V DC Lhedsyt Rlpjpfx Abyoh • Current: 24.90 A • Power rating: 12.62 kW • Frequency: 50 Hz

Condition: used, Year of construction: 2005, Number of belts: 2-belt max. Passage height: 150 mm max. Working width: 1350 mm 1st unit: combined sanding unit Design of 1st unit: steel contact roller, sanding shoe 1st unit: electronic individual segments 35 mm Sanding belt length of 1st unit: 1900 mm Sanding belt width of 1st unit: 1370 mm Sanding belt speed of 1st unit: 18 m/sec 2nd unit: combined sanding unit Design of 2nd unit: rubber-coated contact roller 65° Shore, sanding shoe 2nd unit: electronic individual segments 35 mm Lhedpfjytrf Rsx Abysh Sanding belt length of 2nd unit: 1900 mm Sanding belt width of 2nd unit: 1370 mm Sanding belt speed of 2nd unit: continuously variable 2 - 18 m/sec Belt blowing device: for 2nd unit Cleaning brushes: Yes Finish sanding possible: Yes Vacuum carpet: Yes Feed rate: continuously variable from 2.5 - 13 m/min Control: Touch screen, electric/pneumatic Belt oscillation: yes Infeed height: fixed (top part moves) Table display: digital Working height or table height: 900 mm Motor power: 36 kW Storage location: Nattheim

Condition: good (used), Year of construction: 2017, NUMERICALLY CONTROLLED EDGE BANDER WITH PRE-MILLING (SPINDLES) & CORNER ROUNDING UNIT Brand: SCM Model: K 360 HP-T-ER1 Serial No.: AH/120944 Ref: 123304 Year: 2017 WORKING CAPACITIES: - Panel height to be machined: 8 - 58 mm Thickness 10 to 45 mm when using rounding unit - Panel length for edgebanding: 210 to 2500 mm - Minimum panel width to be machined: 90 to 1100 mm - Edge thickness in coil: 0.4 to 3 mm without rounding max 3 mm with rounding unit - Edge thickness in strips: max 6 mm without rounding max 3 mm with rounding unit - Edge width: panel thickness + 2 mm each side - Feed rate: 11 m/min - Minimum gap between panels: 600 mm - Panel overhang beyond the transfer chain: 30 mm MACHINE CONFIGURATION: - StarTouch control - Prepared for barcode reader - Reel holder table Ø800 mm - Front extension table - Easy size: digital positioning of infeed fence and panel passage height - Anti-adhesive spray unit - Pre-milling unit (RT-V trimmer) 12,000 RPM - Infrared panel preheating at infeed - Glue application unit (VC-VM) with interchangeable glue pot for granules, capacity: 1 kg. Heating time: 12 minutes Pneumatic pre-cut guillotine Digitally positioned pressure station with 3 rollers (1 roller powered and with timer) - Trimming unit (end cutting) tiltable 0-20° 12,000 RPM - Top/bottom flush trimming unit with digital positioning and copying system. 2 mm radius (or chamfer) router 12,000 RPM - Corner rounding unit R2 mm, 12,000 RPM, digital positioning - Top/bottom R1 & R2 mm radius scrapers with digital positioning - Top/bottom straight scrapers - Edge finishing spray device (Nebulizer) OTHER FEATURES: - Pre-milling group motors: 2x2 kW - End trimming motors: 2x 0.19 kW - Lift/lower motor: 0.30 kW - Feed motor: 1.1 kW - Flush trimming group motors (milling): 2x 0.65 kW - CE Marked - Lockable isolator, emergency stop buttons Lhsdsrx S Ipjpfx Abyjh - Power supply: 380 V, three-phase, 50 Hz - Pneumatic supply: 8-10 bar max, dry air - Extraction: 1x Ø100 mm and 5x Ø80 mm Spindles: 780 m³/h Edge trimming: 360 m³/h Scrapers: 2x360 m³/h Max. footprint in working order: 10.80 x 2.40 m Dimensions for transport (LxWxH): 4.85 x 1.20 x 1.70 m Weight: 1568 kg Machine supplied with mounted tools, manual, spare parts list and diagrams.

Condition: excellent (used), functionality: fully functional, number of spindles: 35 Lodpfxow U Aiie Abyehh pneumatic head inclination

Condition: new, Year of construction: 2026, Hebrock - Altendorf Edge Bander F5 next - Brand new machine, still in original packaging with complete equipment - With PLC control including 15" touchscreen - Edge material up to 3 mm - Whispercut jointing head including DIA tool up to 2 mm - Coated maintenance-free glue pot, PUR interchangeable tank - Includes glue drain device downwards - HF milling station with pneumatic milling adjustment - Corner rounding unit - Radius scraper - Surface scraper including pneumatic lift device Lsdpey Iw Nrefx Abyjhh - Buffing station - Combination milling head - Radius milling head R = 2 mm - Radius corner milling unit R = 2 mm - Quick-change system for corner milling unit - Additional changeover motor for corner milling unit with tooling - Radius changeover motor R = 1 mm - Ball bearings 24.1 and 24.2 mm - Multi-radius scraper R1/R2 - Underframe - Additional interchangeable glue pot including stand - Spray system for release agent PUR - Spray system for cleaning agent PUR - Spray system for edge PUR/foil - Nesting for milling head and radius scraper - Pneumatic 3-point adjustment (radius, chamfer, flush trimming) - Jointing up to 50 mm workpiece thickness - LED lighting inside - Workpiece thickness 8–50 mm - Min. workpiece length approx. 160 mm - Feed speed approx. 10 m/min - Dimensions (LxWxH): 4.40 x 1.10 x 1.55 m - Weight: gross: 990 kg; net: 930 kg - Extraction nozzle 1 x 140 mm Delivery and commissioning possible.

Condition: new, Year of construction: 2025, New machine Year of manufacture: 2025 Lsdpox Nbzuofx Abyshh Standard Equipment and Accessories - Swiveling operator panel easily accessible for the operator, "eye-S 15" electronic control system. Includes: * 15" touchscreen monitor * Direct control of 6-8 axes with manual, semi-automatic, and automatic operating modes * Operator assistance with the option to manage 3 different points on the tool for accurate determination of the reference point (zero point) * Capability to store up to 1000 programs with associated images * Capability to store up to 1000 different tools with associated images * USB port * Ready for network connection - Operator aid on the electronic control, including: * Tool database management * Display of coordinates at 3 points on the tool for new reference (zero) point determination * Management of tool edge speed * Operator support for common machining tasks - "Flex" milling fence with automatic adjustment via the electronic control system. Complete fence adjusted to tool diameter, infeed jaw for required chip removal. Movable "FLEX" fence from the worktable. - Aluminium fence jaw for the milling fence with inserts for continuous support - "Fast" table insert, manually adjustable, replaces table rings for optimal workpiece support surface - Electrical pre-wiring for a power feed unit - Spindle rotation direction: right/left - Automatic motor start - Version M-E includes: * Electrospindle with max. performance from 3,400 rpm * Electrospindle power 7.5 kW (10 HP) [S6 -40%] * Interchangeable MK5 spindle * Inverter for speeds from 900 to 12,000 rpm - Interchangeable MK5 milling spindle Safety/Protection - Milling guard, max. tool diameter 160 mm - Electronic motor brake effective even without mains power - Safety sensors during tool change for: spindle stop, spindle lock, opening/closing of tool holder - Electropneumatic spindle lock - Microsafety switch on machine door - Emergency stop button - Lockable main switch - Motor protection switch - Control circuit 24V - CE Declaration of Conformity - Frequency 50 Hz - Base - MACHINE LANGUAGE: German - Standard safety regulations - Manual device for feed support height adjustment according to workpiece thickness with mechanical digital display and horizontal adjustment according to tool diameter. Thanks to the operator panel column, this device allows the feed support to be swung away from the work table. - Voltage 400 V, EU - Quick tool clamping system "T-SET" Allows clamping/unclamping of tools via easy application with a compressed air gun. - L'invincibile TI 5 CE version - "LL" version worktable with two cast iron table extensions; total length 2500 mm, complete with extendable support rail for wide workpieces - Emergency stop switch - Milling spindle diameter 30 mm Availability: short-term