Type 603

KOCH

Condition: used, Year of construction: 2014, power: 75 kW (101.97 HP), controller model: BECKHOFF CONTROL, The pick-up deadlines stipulated in the General Terms and Conditions apply. The absolute latest pick-up date is August 31, 2026! TECHNICAL DETAILS Number of upper units: 4 With positioning via NC: yes Lateral horizontal groups: yes Upper vertical units: yes Horizontal units: yes Number of upper vertical units: 4 With positioning via NC: yes With "Z"-axis positioning via NC: yes Spindles for vertical drilling: 112 Dkodpfezf Ibwox Am Top Number of lateral horizontal units: 4 With positioning via NC: yes With "Z"-axis positioning via NC: yes Spindles for horizontal drilling: 12 MACHINE DETAILS Control: BECKHOFF CONTROL Total installed power: 75 kW EQUIPMENT Protective grid attached to the machine Safety light barriers Automatic waste disposal system The machine will be sold and delivered in its actual and legal condition ("as is, where is") based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before pick-up and assumes responsibility for the installation, securing, and use of the machine at the destination. External Reference: 8649

Condition: excellent (used), Year of construction: 1992, Boy 30 T2 Closing 30 tons Year 1992 Dodeuh U Izjpfx Am Tokp Scrow 32 Spray weighted 123g

Condition: excellent (used), Year of construction: 2017, Koch Technik safety (protective) filter type SA3. Its main tasks are: Dodpfxjzkutde Am Tskp -Vacuum pump protection: Protects blowers and suction pumps against the ingress of fine dust, plastic residues or impurities that could lead to engine failure or seizure -Material dust removal: Filters return air from feeders and material separators, ensuring the cleanliness of the entire pneumatic system. These devices are usually installed in transfer lines before the vacuum generator (pump), most often in granulate dryers (e.g. CKT series) or central raw material feeding systems for injection molding machines and extruders. 4 pieces available - years 2008, 2008, 2010 and 2017 Sold complete with 4 Koch pumps and controls

Condition: used, machine/vehicle number: 008342, Max. panel width: 70 mm Max. panel length: 2100 mm Dkjdpex A Tc Uefx Am Tjp No of injectors: 4 Lateral horizontal groups: yes

Year of construction: 2002, condition: good (used), Make: Matsuura Type: LX-O Control: YASNAC Year: 2002 Specifications Metric US Standard X - Travel 330 mm Y - Travel 300 mm Dkedpolz Rvlofx Am Tsp Z - Travel 250 mm Table Length 540 mm Table Width 320 mm Table load 100 Feed rate X-Axis 90000 mm/min. Feed rate Y-Axis 90000 mm/min. Feed rate Z-Axis 90000 mm/min. Spindle Taper 30 ISO/Bt/Mk Power on spindle 7.5 kW Speeds / ranges 40000 Rpm ATC / revolver 30 Chip conveyor Yes Dimensions (Estimate) Length 2800 mm Width 2600 mm Height 28000 mm Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 2009, machine/vehicle number: A0908/7866, working width: 250 mm, KOCH SBD-B Saw-Mill-Drill - Pass-Through Machine The machine has the following functions - loading magazine - 2 units with a formatting saw diameter 400/30 mm - 4 milling units with oscillation 4KW 18,000 rpm adjustable pneumatic oscillation - 2 horizontal drilling supports head 7 spindles (2 in the 32 mm module, 5 in the 16 mm module) - 3 vertical drilling supports head 14 spindles (12 in the 32 mm module + 2 extreme angular in the 32 mm module - 3 horizontal drilling supports Y axis 2 heads 16 spindles (14 spindles in the 32 mm module + 2 angular in the 32 mm module + 1 head 8 spindle (7 in the 32 mm module + 1 middle angle 32 mm - Return belt to the operator - Supports for long elements The machine does not have doweling units Dimensions of processed elements L- 350-2500 W- 30-200 Gr- 15-75 Machine configured for processing table elements, sample elements in the attachment Dodpfxjwd Rlfe Am Tjkp

Condition: ready for operation (used), Year of construction: 1981, functionality: fully functional, machine/vehicle number: 8109/30, Drilling and Dowel Inserting Machine with PLC + Part Return | 8 heads For sale: a professional through-feed drilling and dowel inserting machine for the production of furniture components, particularly drawer sides. The machine is equipped with PLC control, automatic part return, and an expanded head arrangement (including rear heads), enabling the complete operation to be performed in a single pass—without re-feeding the workpiece. Technical Specifications: - Number of heads/motors: 8 - Head configuration: front/side/rear (double-sided machining in a single cycle) - Control: PLC - Part return: yes (closed production loop) - Maximum working width: 2000 mm - Power supply: 400 V - Pneumatics: yes - Year of manufacture: 1981 - Manufacturer: Gerhard Koch (Germany) - Condition: operational, in ongoing serial production Performance: Approx. 6,000 drawer sides per 8-hour shift Thanks to the rear heads, components that typically require two passes are processed in one, significantly reducing cycle times and increasing productivity. Applications: - Drawer sides - Cabinet components - Batch and repeat production Dsdpfx Aoyzg Udem Tokp - Automated production lines Key advantages: - Single pass processing instead of two - High repeatability - Stable, heavy-duty construction - Perfect for mass production - Proven German technology Location: Elbląg Please contact me for further information.

Condition: excellent (used), Year of construction: 2008, Gravicolor 30 GC 30-M-O-Z Manufacturer: Motan Year of production: 2008 Dkjdpswm Ii Tsfx Am Top A gravimetric dosing and mixing unit designed for direct mounting on the inlet flange of a plastics processing machine. The device allows dosing and mixing of up to 4 granulated components. The actual, measured and weighed quantities are constantly compared with the set values using a modern microprocessor-based control system, which guarantees very high recipe accuracy (+/- 0.1%) thanks to continuous self-optimization. The complete unit includes: 2 feed tanks for primary material or regranulate/primary material 2 feed tanks for masterbatches or additives 2 pneumatically controlled conical dosing heads 2 precision dosing screws with motor drive Material tanks – capacity approx. 7 litres Weighing tank – capacity approx. 0.8 litres Mixing tank – capacity approx. 3.0 litres Manually operated gate valve GRAVInet controller with colour touch panel for recipe, milled material and process data management, vibration compensation and continuous self-optimisation; built-in Ethernet port and standard reporting/printing functions Technical data: Average capacity: 60 kg/h Main component dosing range: 1–100% Additive dosing range: 0.5–10% Power supply: 1/N/PE 230 V 50 Hz Power consumption: 100 W Compressed air: 6–8 bar, without oil and water Weight: approx. 60 kg ✅ The set includes Piovan material feeders - visible in the photos.

Condition: excellent (used), Year of construction: 1995, Combination Unit: Manufacturer: GSG Feeder: Type: 840.02-027 Crusher Descaler: Type: 663.02-017 Wire Range: Ø5.5-16mm For wire rod with approx. 40-60 daN/mm² strength Crushing and Bending Rollers: Carbide Inserts Adjustment with 0.37 kW - 1.15 A gear motor Brush Drive with 0.25 kW gear motor, n=293 rpm Connection Voltage: 380-420 V 50 Hz Dry Coating Unit: Type: BSG/T Filling: Calcium Stearate (e.g., Traxit Type: D S 51 E) Stearate Consumption: approx. 350 g per t of wire Drawing Speed: max. 15 m/s Electrical Power: 2x 0.55 kW gear motors Cassette: 2 slots (supplied with 1x roller block + 1x cassette) Type: PKG/T (TS) Cleaned rolled wire Wire strength approx. 40–60 daN/mm² Wire range max. inlet diameter 9.5mm, finished diameter 3.5–8.5mm Roll dimensions min. Ø115mm, max. Ø125mm, Bore diameter Ø82mm, width 15–25mm Cooling pin diameter 25mm Cooling water consumption approx. 600 l/h Drawing machine: Manufacturer: Koch Type: KHZ 5000 Year of manufacture: 1993 Serial number: 13.821 Number of draws: 1 draw per block Drawing drum: Ø700mm Tensile force: mechanical 5000 N Wire material: mild steel wires Run-in strength: approx. 40 – 45 daN/mm² Maximum drawing range: Inlet diameter 5.0 – 8.5mm Cross-section reduction: 20 x 25% (mechanical gradation) Drawing speed: up to max. 7.0 m/s Brake: Twiflex, type: MRB Drive: AC motor/frequency converter, Siemens PN=110 kW, n=1485 rpm Spooler: Manufacturer: Koch Type: KHS 1250 Year of manufacture: 1993 Factory No.: 13741 Wire diameter: 5 – 8.5 mm Strength: approx. 55 – 70 daN/mm² Winding speed: V=7 m/s, adapted to the drawing machine Filling weight: approx. 3000 kg Spool drive motor: Three-phase motor with external fan Type: 1 PQ 6253 – 6 AA 70- Z A 15 + K 20 + C 14 + H 46 P=37 kW, n=1000-2000 rpm, IP54, design B3 Laying drive motor: 66-671U, 1.5 kW, 170 V, 9.8 A, 1680 rpm, IP 44, B5-200 With Attached tachometer generator TG 20, 20 V / 1000 rpm With attached spur gear SK 32, i=57.53, design B6 Hydraulics: Hydraulic excavator type: H13 AK Pneumatics: Twiflex disc brake type: MRB Dsdpfjr Nfvmsx Am Tskp Pneumatic cylinder type: SPWG 28032-25mm stroke Dimensions: 3100 x 3000 x 1700 mm (L x W x H) without counterweight

Condition: good (used), Koch drying container 1500 liters with additional heating 18 KWr year Dsdjwmbncjpfx Am Tokp price: 7.900€ Contact: Mr. Rainer Eckerle

Condition: used, Year of construction: 2008, Versch GL 18 Closure for medicinal vial GL18 Injection mold with 10-cavity Dkedpfxodqbzqs Am Tsp

Condition: used, Year of construction: 1984, CNC Milling Machine Heckler & Koch BA 20 CNC Manufacturer: Heckler & Koch (Germany) Type: Vertical CNC Machining Center (Milling Machine) Control system: Depending on the version – Siemens, Heidenhain, or proprietary HK system (the photos show a panel with a monitor and traditional keyboard, most likely Heidenhain or Siemens Sinumerik control). Worktable: typically 2000 × 500 mm (designation BA 20 = 2000 mm table length) Working travels (X/Y/Z axes): X: approx. 2000 mm Y: approx. 500 mm Z: approx. 500–600 mm Dksdpfxow Uac Hs Am Tsp Spindle power: usually 10–15 kW Spindle speed: up to approx. 6000 rpm (depending on the version) Tool holder: SK40 or SK50 (SK40 holders visible in the photos) Tool magazine: usually 16–20 tools Cooling: via external coolant nozzle (flexible blue pipe visible in the photos) Total weight: approx. 6–8 tons Power supply: 400 V, 50 Hz, connected load approx. 20–25 kVA Applications: - Production of medium-sized metal parts - Defense, machinery, and automotive industries - Suitable for batch and single-piece production Equipment: control panel, keyboard, mouse, vices, guards 📌 Applications: - Metalworking - Batch and single-piece production - Metalworking shops, manufacturing plants

Condition: used, Year of construction: 2006, drilling depth: 28 mm, Used Koch Drilling and Dowel Insertion Machine, Sprint-PTP-3 Technical data of the machine: Workpiece dimensions: Length Y: 110-800mm Width X: 20-1200mm Thickness Z: 14-60mm Material: Chipboard/MDF/Softwood Machine with 2 working areas. 2 workpieces with a maximum width of 600mm each can be loaded independently of each other. Working height 900mm - with horizontal drilling station Dksdozbunkopfx Am Tep - with glue application and dowel insertion station - with 1 oscillating conveyor - Drilling distance vertically Z above the support table: 35 mm - 1 stop rail on the left and right - Mechanical digital displays for height adjustment - Work cycle triggered by a manual button Koch Numeric with 1 NC axis (X) Positioning control with PC (Windows XP Professional PC) Including widened machine frame for a maximum workpiece width of 1200mm 2 additional workpiece clamping cylinders Center stop for 4 working areas (removable for wide workpieces) Horizontal drilling station with 1 drilling spindle: Max. drilling depth 28mm Drill chuck Ø10mm Total drill length 70mm Drill speed 7200 rpm With dowel hole blow-out Glue application and dowel insertion station Dowel diameter: 8mm Dowel length 30mm Dowel projection 7-14 mm Set to 11mm Tolerance for wood dowels: --- Dowel length +/- 1 mm --- Dowel diameter +0.1/-0.2 mm With electronic glue monitoring (ELC) A monitoring device is installed before the glue valve, which measures the glue flow during each work cycle. If no glue is injected at a valve, the machine interrupts its work cycle and displays the corresponding glue valve in the control cabinet. Electrical values: Connection value: 400V, 50 Hz, 3 phases Voltage fluctuations max +6% to 10% Air connection 1 x R 1/2" internal thread 7 bar Extraction air velocity: approx. 30m/sec

Condition: excellent (used), Lightly used automatic TC, TU, TZ profile production lines, designed for manufacturing and roll forming TC, TU, TZ profiles up to 1.5 mm metal thickness. Technical Specification: Manufactured in: Estonia Adjustable profile height: 100 – 250 mm Dksdex Sx R Sspfx Am Tep Profile width: 50 mm Profile edge (folded): 15 mm Minimum rollable sheet thickness: 1 mm Maximum rollable sheet thickness: 1.5 mm Roll distance: 300 mm Machine dimensions: 900 x 4000 mm The machine is not equipped with a guillotine or perforating rolls. Operation is straightforward, controlled via two buttons. If you have further questions, we will be happy to answer them.

Condition: good (used), Approx. 221 Corlettes / Multi-Boxes, width 2m / 2.50m / 2.70m, partly stackable - used - : Prices (net) per unit ex location: €149 Price (net) Type 3 – stackable: €169 per unit, ex location! Manufacturer: Cordes und Koch Type: Corlette / Multi Box Dimensions (L × W × H in cm) Type 1 = 13 units (only sold as a complete lot) 250 x 115 x 180 Colour: blue Type 2 = 2 units 270 x 115 x 240 Colour: green Type 3 = 192 units, approx. 62 stackable Minimum purchase: 10 units Djdjxc E Hlspfx Am Tekp 200 x 115 x 180 Colour: blue Type 4 = 14 units (only sold as a complete lot) 270 x 115 x 188 Colour: green Condition: good Available: immediately Location: 63128 Dietzenbach