Used Lecitrailer Low Loader Semitrailer for sale (15,154)

Condition: new, maximum load weight: 40,320 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory with vehicles available immediately and in the short term on our website. Below is an excerpt of the features. Complete equipment list available upon request. GOOSENECK Gooseneck with a rear slope of approximately 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). Hardwood decking approximately 30 mm thick. Gkedpfjz N Nx Rox Ap Dec - 2-inch kingpin - Yellow-red air couplings on the galvanized connection bar at the front. - 4 wheel chocks with holder on the front wall (± 5 kg). LOADING AREA 5 pairs of lashing rings that fold outwards (LC 5,000 daN). 3 pairs of lashing rings that fold outwards (LC 10,000 daN). 1 pair of lashing rings lying at the front in the loading area (LC 10,000 daN). Hardwood decking approximately 48 mm thick, with diamond plate decking over the axles. - On the gooseneck and at the rear, left and right, one holder each for the warning signs, including a socket. - A galvanized steel front wall. - 3 height-adjustable wooden planks. - Galvanized folding supports under the slope of the loading area. - A holder for a rotating beacon at the rear of the semi-trailer. - Height-adjustable tarpaulin superstructure, approximately 3,960 mm. - Galvanized front wall with a tensioning mechanism for the sliding curtains. - Height-adjustable by approximately 400 mm. - Roof from the EDSCHA brand, which can be moved forward on aluminum roof rail profiles. - 3 pairs of sliding rails in the loading area. - The superstructure can be hydraulically widened at the rear to the left and right by approximately 750 mm (for loading and unloading). - Sliding cover with a pivoting portal beam. - Sliding tarpaulin with approximately 700 mm of reserve in length, with tension straps at intervals of approximately 600 mm. - Height of the top edge of the superstructure approximately 3,960 mm (loaded). - Driving with the sliding cover open is not permitted and will damage the tarpaulin. - Attachment rail for aluminum ramps at the rear of the vehicle. - Control valves for the hydraulic widening of the superstructure, mounted on the right side of the semi-trailer. (± 4 kg) - White reflector tape according to EU regulations, red on the sides and rear. - Electro-hydraulic unit at the rear under the loading area. (± 45 kg) - Holder for a pair of warning signs on the front wall. - Four warning signs, approximately 400 mm extendable, approximately 423 x 423 mm, with an LED position light (± 25 kg). - On the warning signs, a holder for a rotating beacon. - 7 pairs of rail pockets for plug-in rails, approximately 100 x 50 mm, in the outer frame of the loading area (± 21 kg) - Lift axle on the front axle, controlled by TEBS-E depending on the current axle load and loading condition (± 69 kg). - 6 pairs of recessed lashing rings along the central beam (LC 5,000 daN). - 1 pair of recessed lashing rings along the central beam at the rear (LC 10,000 daN). (± 27 kg) - A painted layer of sand on the diamond plate on the gooseneck and in the loading area as anti-slip protection. - 1 LED reversing light, each on the left and right, in front of the first axle. - 2 LED work lights mounted on the rear panel. - An acoustic warning signal when reversing. ACCESSORIES - Cable for supplying the electro-hydraulic unit and/or the electric winch (approximately 35 mm², approximately 3.5 m long, max. 250A) between the semi-trailer and the tractor unit with a plug connection (NATO-NATO). FIFTH WHEEL BRACKETS JOST fifth wheel brackets, mechanical, with a 2-spee

Condition: used, empty load weight: 7,800 kg, maximum load weight: 21,200 kg, overall weight: 29,000 kg, axle configuration: 2 axles, first registration: 09/1968, loading space length: 12,300 mm, loading space width: 2,500 mm, loading space height: 900 mm, suspension: steel, tire size: 235 / 75 R 17,5, color: red, mileage: 1,001 km, gearing type: other, driver cabin: other, Vehicle location: Bovenden, 2 axles, leaf spring suspension, extendable to 3m, hydraulic ramps, dual tires. Body: Hydraulic ramps. Length over axles approximately: 8200mm, length over kingpin: 3200mm. ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale and errors! Gsdpfei Rnwwox Ap Dskc

Condition: new, maximum load weight: 43,929 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, loading space length: 16,690 mm, loading space width: 2,550 mm, total width: 2,550 mm, total height: 3,570 mm, Year of construction: 2026, Equipment: ABS, Kässbohrer K.SLA R 4 / 2N ? 18/40 Low Loader, Telescopic with Wheel Recesses (NEW) ----Equipment & Highlights Technology & Construction: - Extendable low loader with wheel recesses - Overall length: 13,190 mm, platform: 9,240 mm + 3,500 mm extension - Platform height: only 875 mm for low loading height - Total width: 2,550 mm + 600 mm extension - Unladen weight: approx. 14,071 kg - Gross vehicle weight: 58,000 kg (80 km/h) / 63,800 kg (60 km/h) Chassis & Axles: - 4 BPW axles, front 2 fixed, rear 2 self-steering - Lift axle (automatic + manual) Gjdpfox Efznjx Ap Dokc - Air suspension with load gauge - WABCO EBS 4S/3M, ABS & RSS - WABCO Smartboard (axle load, suspension, diagnostics) - 16x tyres 245/70 R17.5 (M+S + 3PMSF) - Tyre pressure monitoring according to R141 Ramps & Loading Area: - Foldable 40-ton ramps - Ramp length: 2,750 mm, width: 850 mm - Hydraulic sliding system - 45 mm hardwood floor + steel chequer plate over wheel arches - Wheel recesses + covering bridges included - Digger arm recess at rear Load Securing: - Extensive lashing points: - 2×2 lashing rings 5,000 daN & 1×2 lashing rings 10,000 daN on gooseneck - 3×2 lashing rings 5,000 daN & 4×2 lashing rings 10,000 daN on platform - 8,000–10,000 daN on outer frame/wheel recess area - 5×2 stake pockets, removable stanchions 50×100 mm - Container locks for 1×20 ft or 1×30 ft containers Equipment & Comfort: - 1× tool box (700×400×360 mm) - Stanchion box - Beacon light - LED side lighting, LED work lights - Wheel chocks - Width marker boards with LED - Standard 2" kingpin - Metallized chassis (Zn/Al 85/15) – high corrosion protection - Colour: RAL 9005 Black ----Special features: - New & immediately available - High payload, extremely flexible application - Perfect for machinery transport, construction equipment, vehicles, etc. - Very robust construction, high-quality BPW components For further information, we are at your disposal.

Condition: new, maximum load weight: 33,865 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Equipment: ABS, Excerpt of Equipment Gooseneck * with angled front corners approx. 45° and rear angle approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood decking approx. 30 mm thick Loading Platform * in double-extendable design with rear angle approx. 500 mm x 8° * 6 pairs of lashing rings that fold outwards (LC 5,000 daN) Gsdpfx Aezlwm Njp Dekc * 4 pairs of lashing rings that fold outwards (LC 10,000 daN) * 1 pair of lashing rings positioned horizontally at the front of the loading platform (LC 10,000 daN) * 1 intermediate table approx. 250 mm * Hardwood decking approx. 48 mm thick, with diamond plate decking over the axles * Cutouts in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) Axles * BPW axles and suspension, all axles with hydro-mechanical forced steering * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve * Axle tool Tires * 245/70 R 17.5, load index (146/146 F) * Brand of our choice Kingpin * JOST kingpins (mechanical) with 2-speed gear for approx. 24 t lifting capacity (approx. 50 t test load) Braking System * in accordance with EU regulations with EBS-E (2S2M) without connecting lines to the semi-trailer tractor Painting * First-class and durable corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer * A high-quality 2-component (2K) * Topcoat, single color in RAL 3002 carmine red * Rear section metallic and painted in RAL 9010 (pure white) * Metallic paint not possible Steel Construction * made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical System * in accordance with EU regulations * Lighting 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX on the front connection bar with sockets 24N, 24S & 15 pole * Connection according to ISO. 24N ISO-1185 24S ISO-3731 15 pole ISO-12098 Incl. the following additional equipment * 2-inch kingpin * One galvanized steel front panel, approx. 400 mm high * Yellow-red air couplings on the galvanized front connection bar * 4 wheel chocks with holder on the front panel (± 5kg) * A spare wheel holder in front of the front panel * Electro-hydraulic power unit (± 45kg) * Steering from the front and rear by means of cable remote control operated via push buttons, with single-axle control (without installation in the tractor unit) * Mounting at the rear of the gooseneck for aluminum loading ramps * European reflector plates (red-yellow) at the rear of the trailer * Yellow reflector tape in accordance with EU regulations on the side, on the extension and at the rear of the trailer * On the gooseneck and at the rear panel, one holder each on the left and right for warning signs including socket * Mounting rail for aluminum loading ramps at the rear of the vehicle * A holder for a rotating beacon at the rear of the trailer * Galvanized folding supports under the angle of the loading platform * A mud flap at the rear of the trailer * Manual and description on USB stick * Speed stickers 80 km/h at the rear and on both sides * Load gauge for determining the axle loads including load diagram.

Condition: new, overall weight: 47,000 kg, axle configuration: 2 axles, Year of construction: 2026, Technical Data MAX510-Z-2H-ATX-A-6.85-PA Speed: 80 km/h Total weight: 47,000 kg Saddle load: 23,000 kg Axle load: 24,000 kg Gooseneck length: 3750 mm Saddle height loaded: 1200 mm Rear overhang: 2300 mm Loading area length: 6,850 mm Extendable by: 5,500 mm Loading height at max. load: 350 mm Frame length: 2,600 mm Loading height, rear frame at max. load approx.: 1,005 mm Suspension travel: -150/+450 mm Axle track: 1360 mm Overall width: 2,540 mm Total weight depends on the saddle load. Low-bed: Low-bed with external, extendable beams. "SUPER LOW" design, length approx. 6,850 mm. Low-bed with fixed hardwood floor, approx. 40 mm thick, and mechanical locking mechanism. The supply lines are protected in the extendable beams and automatically adjust to the respective low-bed length. 5 pairs of lashing rings, foldable outwards (LC 10,000 daN). 6 pairs of threaded blocks on the inner beam for mounting screwable RUD rings. Rear frame: Rear frame with closed outer frame, diamond-plate flooring and continuous prism-shaped excavator well, approx. 1,250/700 x 505 mm, open at the rear. 2 pairs of lashing rings, foldable outwards (LC 10,000 daN). 1 pair of lashing rings lying in the well (LC 8,000 daN + 5,300 daN). 2 pairs of stake pockets for stake pockets 100 x 50 mm in the outer frame. Gooseneck: Gooseneck in SNT design for optimizing the loading area length, length approx. 3,785 mm. Gooseneck hydraulically adjustable up/down and extendable. Technical saddle load: 23,000 kg For semi-trailer tractor: 4x2, 6x2 and 6x4 PENDULUM AXLE: "PENDULUM AXLE", all axles hydro-mechanically forced steered. Hose burst valve on the axle compensation cylinder with automatic RESET function. Hydraulic cylinders with shut-off valves and quick-release coupling for securing in the raised position. Final coating of the axles with 2 layers of 2-component paint, solid color in "FAY-Gray-34-0260". Technical axle load: 12,000 kg Hydraulic axle equalization. Axle tool. Braking system: Braking system according to EU regulations with EBS-E (2S2M) without connecting lines to the semi-trailer tractor. Electrical system: Electrical system according to EU regulations, lighting 24 volts ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection bar with sockets 24N, 24S & 15-pin. Connection according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel construction: Steel construction made of high-strength fine-grained steels. Steel grades: S355J2+N/S355MC (Yield strength 355MPa) S690QL/S700MC (Yield strength 690MPa) Painting: First-class and durable corrosion protection of the standard shot-blasted welded frame is guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) top coat, solid color in RAL colors of your choice. Rear section metallized and painted in RAL 9010 (Pure White). Metallic paint not possible. Tires: Tires 245/70 R 17.5 3PMSF Gkodsizu Nwopfx Ap Dec At the manufacturer's option. Load index (146/146F) Preparation for mounting screwable container positioning for 1 x 20' or 1 x 40' container on the outer beams. Without container locking mechanisms. i i2" Kingpin iA galvanized steel front wall, approx. 400 mm high. iA spare wheel with holder in front of the front wall. i2 pieces of wheel chocks with holder on the front wall. iYellow-red air couplings on the galvanized front connection bar. Steering from the front and rear by means of a cable remote control via push buttons, with single-axle control. (without installation in the semi-trailer tractor) i Hydrauli

Condition: used, empty load weight: 8,370 kg, maximum load weight: 34,630 kg, overall weight: 43,000 kg, axle configuration: 3 axles, first registration: 12/2021, loading space length: 13,600 mm, loading space width: 2,550 mm, loading space height: 1,020 mm, suspension: air, tire size: 445/45R19.5, color: grey, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden. 3 axles, SAF axles, air suspension, first axle liftable, last axle with trailing steering, ABS (anti-lock braking system), lashing eyes, raise and lower function, detachable loading ramps, rear support, landing legs, toolbox. Body: Göbel low loader, 43,000 kg. Detachable ramps (reinforced version) available at an additional net cost of €1,800 Gkedpfx Ajyhraksp Doc Loading area: Gooseneck 4,500 mm, bed length 9,100 mm, 1st axle lift with starting assistance, 28 mm sealed hardwood floor, 25 pairs of flush-mounted heavy-duty lashing rings, each rated at 8,000 kg, side rail for lashing straps with claw hooks approx. every 500 mm, rated at 5,000 kg each, insert sleeves, 80 mm stake pockets, chassis hot-dip galvanized. For an additional charge, available with matching tractor unit 2648 LK (17697) and ballast platform (17699)! Approx. 54,160 km mileage! Loading height approx. 1,020 mm! ACCESSORY INFORMATION WITHOUT GUARANTEE. Subject to changes, prior sale, and errors!

Condition: new, overall weight: 48,000 kg, axle configuration: 3 axles, suspension: air, tire size: 235 / 75 R 17,5, color: other, gearing type: other, front tire size: 235 / 75 R 17,5, rear tire size: 235 / 75 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Heavy-duty design, air suspension with lift axle, axle load gauge for axle load monitoring, upper deck length approx. 4,400 mm including slope, lower deck length approx. 8,500 mm, loading height approx. 900 mm, suitable for 2-axle and 3-axle semi-trailer tractors, adjustable kingpin, front wall, 16 x lashing point pockets in the outer frame, 32 x lashing points, ramp approx. 4,200 mm long (2-part), ramps with climbing strips on the outside, ramps for driving over on the gooseneck, further options available at an extra cost, last axle as a steering axle, warning signs + lighting and rotating beacon, widening to 3 m with timber, hydraulic adjustment of the ramps, -- subject to printing errors, mistakes and changes, sample images --, more data available at: !, More Details: ! Gsdpsz Rwa Sjfx Ap Djkc

Condition: new, maximum load weight: 48,930 kg, overall weight: 63,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and in the short term, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck * with beveled front corners, approximately 45° and with rear bevel approximately 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring, approximately 30 mm thick Loading platform * in a double-extendable design with rear bevel approximately 500 mm x 8° * 5 pairs of lashing rings, foldable outwards (LC 5,000 daN) * 4 pairs of lashing rings, foldable outwards (LC 10,000 daN) * 1 pair of lashing rings, horizontally at the front of the loading platform (LC 10,000 daN) * 1 intermediate table, approximately 250 mm * Recesses in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) * Hardwood flooring, approximately 48 mm thick, with diamond plate flooring over the axles Axles * BPW axles, hydro-mechanically forced steering * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve Tires Gjdpfozlwm Asx Ap Djkc * 245/70 R 17.5 3PMSF, load index (146/146 F) * TPMS tire pressure monitoring system according to ECE R 141 Kingpin * JOST kingpins (mechanical) with a 2-speed gearbox for approximately 24 t lifting capacity (approximately 50 t test load) Braking system * according to EU regulations with EBS-E (4S3M) Steel structure * made of high-strength fine-grained steel * Steel grades: S355J2+N/S355MC (yield strength 355 MPa) * S690QL/S700MC (yield strength 690 MPa) Electrical system * according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the turn signal * ASPÖCK-UNIBOX on the connection strip at the front with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Painting * Complete steel structure automatically blasted after welding using a blasting wheel system * Second blasting with corundum for optimal adhesion of the coating system * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection * Final coating with 2 layers of 2K topcoat, solid color in RAL 3002 carmine red, according to the RAL 841GL system * Rims in silver. Rear part metallized and painted in RAL 9010 (pure white) * Metallic paint is not possible * Paint structure tested in the salt spray test according to ISO 9227-NSS * Sealing of cavities with special wax Including the following additional equipment 2 inch kingpin * Electro-hydraulic unit (± 45 kg) * Follow-up steering from the front and rear, controllable by means of a cable remote control via push buttons, with single-axle control (without installation in the central control unit) * One bracket for warning signs on the left and right of the gooseneck and on the rear panel, including socket * One bracket for a rotating beacon on the rear of the trailer * Aluminum side panels and rear panel on the gooseneck, pluggable, approximately 2,440 x 400 mm (L x H) * The rear galvanized stake pockets are removable. (Length of the superstructure approximately 2,560 mm) (± 46 kg) * A tool box, galvanized, integrated into the beveled gooseneck (± 47 kg) * 4 pairs of WADER container pockets in the loading platform for a 20', 2x 20', 40 or a 45' container (± 40 kg) * 7 pairs of stake pocket for stake pockets approximately 100 x 50 mm in the outer frame of the loading platform (± 21 kg) * Extensions, galvanized

Condition: new, maximum load weight: 34,104 kg, overall weight: 47,000 kg, axle configuration: 2 axles, Year of construction: 2026, Further information here: Gkjdpfx Asv D Abgjp Djc

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) Gsdpfx Asrgzv Njp Dekc * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: new, maximum load weight: 36,500 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and in the short term, on our website. Excerpt from the equipment Complete equipment available upon request GOOSENECK * Designed in SNT to optimize the loading area length * Length approximately 3,700 mm, with a rear slope of approximately 1,000 mm x 6° For SZM: 4 x 2 and 6 x 2 Gsdjzzhfujpfx Ap Dekc * ASPÖCK-UNIBOX Grid floor with 5 mm sheet metal reinforcement on the gooseneck and the rear slope * 2-inch kingpin * Guide plate from the gooseneck for the fifth wheel plate, approximately 500 mm wide, round * NATO socket on the connection strip at the front on the gooseneck * 1 pair of pluggable aluminum side panels, approximately 400 mm high, in anodized design * 1 LED work light each on the left and right, mounted at the top of the front wall * Controlled via on/off switch (operation of the work lights from the SZM is not possible in this case) LOADING AREA * Length approximately 9,600 mm, with a rear slope of approximately 900 mm x 6° * Loading area after the gooseneck can be hydraulically raised and lowered, length approximately 3,000 mm * Load capacity up to approximately 9,000 kg on the lifting platform and the loading area, continuous grid floor with approximately 5 mm sheet metal underlay as additional reinforcement, designed for point load TIRES * 235/75 R 17.5 3PMSF, twin tires, manufacturer of our choice * TPMS tire pressure monitoring system in accordance with ECE R 141 AXLES * BPW axles and suspension * 1st and 2nd axles rigid * 3rd axle with trailing steering * 3rd axle with electro-magnetic reverse lock, activated via reverse gear and manually * 1st axle with start-assist * Technical axle load: 12,000 kg each AIR SUSPENSION * with raising and lowering valve HYDRAULIC LOADING RAMPS * 1 pair of two-piece AXS steel ramps with grid floor and a length of approximately 4,920 mm and a width of approximately 900 mm * Hydraulically foldable ramp tips, ramps can be individually moved hydraulically outwards by approximately 235 mm and inwards by approximately 365 mm * Flashing lights on the outer sides of the ramp tips, with a switch next to the ramp control * Ramp securing in driving position by means of a quick-release fastener * Painted sand coating on the outer frame of the ramp as well as on the ramp tip * Mechanical supports in drop tube design on the sides of the ramps to support when docking with loading ramps * Control valves for the hydraulic ramps on the right side of the vehicle BRAKE SYSTEM * From WABCO EBS-E according to EU regulations SURFACE TREATMENT * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure the best corrosion protection PAINTING * Semi-trailer carmine red (RAL 3002) * Rims silver gray, side panels aluminum natural * Wheel hubs according to axle manufacturer, lamp sign pure white (RAL 9010) EQUIPMENT * Front wall made of steel, pluggable, approximately 1,600 mm high * Including connection strip for supply lines to the SZM, mounted approximately 1,000 mm from the lower edge of the outer frame profile * Possibility to attach lashing chains on the inside of the front wall on the left and right * Including aluminum tray underneath on the left and right for storing chains or lashing straps behind the front wall, approximately 12 mm thick DELIGNIT surface, screwed on * 2 pairs of screwable lashing rings additionally (LC 5,000 daN) * Electric winch, approximately 5,400 kg pulling force, with

Condition: new, maximum load weight: 51,780 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Here is an excerpt of the equipment. Complete equipment details are available upon request. Gkedpez N Nxwsfx Ap Djc GOOSENECK: Gooseneck with SNT design to optimize the loading area length, approximately 3,700 mm long, with a taper at the rear of approximately 1,000 mm x 10°. For SZM: 4 x 2, 6 x 2, and 6 x 4. Steel front wall, plug-in, approximately 400 mm high. ASPÖCK-UNIBOX on the connection strip at the front with 24N, 24S & 15-pin sockets. 3 kW electric-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches. Outrigger of the gooseneck with mounting holes for screwable lashing rings. One mounting hole in the rear upper area of the gooseneck outrigger for a screwable lashing ring. 1 pair of screwable lashing rings included (LC 10,000 daN). On the gooseneck, 1 pair of plug-in aluminum side panels, approximately 400 mm high, in an anodized finish. On the gooseneck, one plug-in aluminum rear panel, approximately 400 mm high, in an anodized finish. Approximately 40 mm thick hardwood flooring above the gooseneck. 2-inch kingpin. 1 crossmember pocket rail mounted in the loading bed of the gooseneck in front of the taper, for plug-in crossmembers, approximately 100 x 50 mm. LOADING AREA: Loading area in an extendable design, approximately 8,800 mm long, with a taper at the rear of approximately 500 mm x 10°. A recess in the loading area that extends into the taper to accommodate the excavator arm, approximately 2,490 x 750 x 210/290 mm (L x W x H). TPMS tire pressure monitoring system according to ECE R 141. BPW axles and suspension, 1st and 2nd axles rigid, 3rd and 4th axles steered. 3rd and 4th axles with electro-magnetic reverse locking via reverse gear and can be activated manually. Technical axle load: 12,000 kg each. Air suspension with lifting and lowering valve. Mechanical fifth-wheel supports with 2-speed gearbox and crank. Continuous hardwood flooring approximately 50 mm thick in the loading area, interrupted between the axles (thus increasing the coefficient of friction). 1 intermediate table with a recessed loading area, approximately 300 mm wide, for the extension tube with a large cross-section and sheet metal flooring. 1 pair of lashing rings on the front crossmember (LC 10,000 daN). 6 pairs of recessed lashing rings in the outer frame of the loading area, foldable outwards (LC 10,000 daN). Additionally, 1 pair of lashing rings on the outside of the front crossmember of the loading area, rotated approximately 90° inwards towards the loading area (LC 10,000 daN). Extensions (galvanized), extendable approximately 230 mm on each side (without wooden planks). 1 pair of fixed wheel arches, open to the extension, approximately 700 x 410 mm (W x D), in the loading area in front of the 1st axle. Between the 2nd and 3rd axles in the loading area, 1 pair of fixed wheel arches, approximately 1,695 x 700 x 410 mm (L x W x D). 1 pair of mechanical rear supports. 245/70 R 17.5 3PMSF twin tires - brand of our choice. HYDRAULIC LOADING RAMPS: DR-15/60-900-4350-HB-HV-M. A pair of two-piece steel ramps with a length of approximately 4,350 mm and a width of approximately 900 mm. Hardwood flooring. Hydraulically foldable ramp tips. Ramps can be individually hydraulically moved outwards approximately 235 mm and inwards approximately 215 mm. Hardwood flooring on the taper of the loading area. Ramp with hardwood fl

Condition: used, maximum load weight: 16,300 kg, overall weight: 22,000 kg, axle configuration: 1 axle, first registration: 08/2022, next inspection (TÜV): 09/2026, BPW 10-ton axles, frame construction made of high-strength Domex 700, total loading area 11,800 mm, loading area length 8,350 mm, Knorr brake EBS 4s/2k (ASR), rear support legs foldable, 25,000 kg, pneumatic valve for adjusting the No. 4 wheel chocks, electric winch with remote control, 3x2 tie-down points in the platform outer frame (8 tons), aluminum frame L: 2,300 mm - W: 500 mm, hot-dip galvanized, toolbox, rollers for the loading platform, extendable bumper, ramp holder. Gkedpsih E Hyofx Ap Dsc

Condition: new, maximum load weight: 46,800 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory with vehicles available for immediate and short-term delivery on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck * Gooseneck with beveled front corners at approximately 45° and a rear bevel of approximately 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring, approximately 30 mm thick Extendable platform * with rear bevel of approximately 1,000 mm x 8° * 5 pairs of lashing rings that fold outwards (LC 5,000 daN) * 3 pairs of lashing rings that fold outwards (LC 10,000 daN) * 1 pair of lashing rings, lying horizontally at the front of the platform (LC 10,000 daN) * Recesses in the outer frame of the platform for attaching tension straps (LC 2,000 daN) * Hardwood flooring, approximately 48 mm thick, with non-slip steel plate flooring over the axles Axles * BPW axles and suspension * 1st axle rigid, all other axles hydro-mechanically forced-steered * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve * Axle tool kit * Tires * 245/70 R 17.5 3PMSF * Load index (146/146 F) * TPMS: TPMS tire pressure monitoring system according to ECE R 141 Kingpin * JOST kingpins (mechanical) with 2-speed gearbox for approximately 24 t lifting capacity (approximately 50 t test load) Braking system * in accordance with EU regulations with EBS-E (4S3M) Paint finish * Complete steel construction automatically blasted with a blasting wheel system after welding * Second blasting with corundum for optimal adhesion of the coating system * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure the best corrosion protection * Final coating with 2 layers of 2K topcoat * solid color in RAL 3002 carmine red according to the RAL 841GL system * Rims in silver gray. Rear section metallized and painted in RAL 9010 (pure white) * Metallic paint not possible * Paint structure tested in the salt spray test according to ISO 9227-NSS * Sealing of cavities with special wax Gjdpfx Apszk S Dmo Djkc Steel construction * made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system * in accordance with EU regulations Lighting * 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the turn signal * ASPÖCK-UNIBOX on the connection strip at the front with 24N, 24S & 15-pole sockets * Connection according to ISO. 24N ISO-1185 24S ISO-3731 15-pole ISO-12098 Incl. the following additional equipment * 2-inch kingpin * One galvanized steel front wall, approximately 400 mm high * Electro-hydraulic unit (± 45kg) * Steering from the front and rear via cable remote control, operated via push buttons, with single-axle steering (without installation in the central beam) * 1 pair of recessed lashing rings along the central beam at the rear in the bevel (LC 10,000 daN) (± 3kg) * On the gooseneck, aluminum side boards and rear wall, pluggable, approximately 2,440 x 400 mm (L x H) * The rear galvanized plug-in stakes are removable. (Length of the structure approximately 2,560 mm) (± 46kg) * A galvanized toolbox, integrated in the beveled gooseneck (± 47kg) * 3 pairs of WADER container pockets in the platform for a 20' (30?) or a 40? container (± 30kg) * 6 pairs of stake pockets for plug-in stakes, approximately 100 x 50 mm, in the outer frame of the platform (± 18kg) * Extensions, galvanized, extendable by app

Condition: new, overall weight: 36,000 kg, axle configuration: 3 axles, loading space length: 13,620 mm, loading space width: 2,480 mm, total width: 2,550 mm, total height: 4,000 mm, Year of construction: 2026, Equipment: ABS, Krone SDP 27 step semi-trailer with spreader tail immediately available Photos of the spreader tail to follow shortly * Fifth wheel height unloaded: 1,180 mm * Multilock external frame, universal load securing option every 100 mm * for loading space length: 13,620 mm i. L. Low bed 9,610 mm / platform 4,010 mm, loading space width 2,480 mm i. L. * 3 axles, each with a load capacity of 9,000 kg * Wheelbase: 1,310 / 1,310 mm * BPW unit with air suspension * Brake drums, 300 x 200 mm (for 17.5" rim) * Fully automatic electronic lifting axle control for 1st axle, depending on load * Air suspension with lifting and lowering device, including automatic ride height reset * 12-fold tires, 235/75 R 17.5 * Multifunctional rear lights (full LED) * Incl. 1 reversing light * 2 additional LED reversing lights * 1 toolbox, plastic 650x490x450 mm * 1 additional toolbox, plastic * Combination: truck-mounted forklift / hydraulic rear extension * 30 mm thick, waterproof plate floor, for floor loads up to max. 7,000 kg forklift axle load * hydraulic lifting roof with 500 mm total lift * Certificate for load securing in accordance with EN 12642 Code XL Gkedpfx Astrib Esp Djc * Certificate for load securing for beverage transport (VDI 2700 Sheet 12) * Steel parts blasted, KTL primed with zinc phosphate coating and powder coated * Chassis including outer frame RAL 9005 DEEP BLACK * Tarpaulin color RAL 9006 WHITE ALUMINUM * Structure (front wall, rear portal, rear wall) RAL 7035 LIGHT GRAY We are happy to provide you with further information

Condition: new, maximum load weight: 27,000 kg, overall weight: 36,000 kg, axle configuration: 3 axles, Year of construction: 2026, Equipment: ABS, crane, Step-frame semi-trailer in roll-off tipper design 3 axles with disc brakes Gkjdpfxezirgxs Ap Djc SAF axles Lift axle Tires 385/55 R 22.5 Gear-driven winch LED lighting Work lights 25-ton capacity in sliding/articulated design for container lengths up to 7,500 mm Roller height approx. 1,300 mm Hydraulic internal locking Soft stop Quick release Fifth wheel as loading platform with side boards 1 unit available in stock. Different equipment/design available on request. Further information available on request.

Condition: new, suspension: other, color: other, gearing type: other, driver cabin: other, emission class: none, fuel: biodiesel, Storage compartment for aluminum ramps, price per storage compartment, length approx. 2.48 m, width approx. 1 m, height approx. 27 cm, , --  Misprints, errors and changes reserved, sample images --, More information at: !, More details: ! Gkodpfx Aoz R Tf Eop Dsc

Condition: new, overall weight: 36,000 kg, axle configuration: 3 axles, suspension: air, tire size: 385/65 R22,5, KRONE SD refrigerated trailer | Carrier 1550 deep-freeze unit | KRONE axles with disc brakes | Toolbox | Spare wheel holder | Temperature recorder | Pallet box | Lifting axle | Double-deck. Subject to errors and prior sale. Gkedpjxghkhefx Ap Doc

Condition: new, maximum load weight: 45,250 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. The following is an excerpt of the equipment. Complete equipment details are available upon request. Gkedpfxoz Dmn Ro Ap Dec Chassis, gooseneck: Special steel frame made of high-strength fine-grained steels, electrically welded at the connection points, well-dimensioned outer frame. 4-axle arrangement. Wheel arches above the axles with spray mist suppression. All steel parts are sandblasted. Lateral impact protection made of anodized aluminum installed. Increased point load of approximately 30,000 kg over approximately 4,000 mm. Special design in the gooseneck area for maximum low-bed length in combination with AluLeg support legs instead of telescopic support winches, maximum rear swivel radius of the tractor unit approximately 2,100 mm. Special superstructure with rear beam widening: DINKEL – special superstructure. Self-supporting aluminum roof beam/profile approximately 120 x 100 mm, sliding cover with plastic flaps. Rear beams can be widened to approximately 4,200 mm (only for loading and unloading). Three sliding beams per side with rubber strap relief. Additional center beam locking mechanisms in the roof beam and parking position, using a pull cable and spring latch. DINKEL – lifting roof mechanically height-adjustable. Lifting roof height approximately 400 mm, operable on both or one side, without opening the opposite side and the doors. Additional height adjustment of approximately 480 mm in approximately 40 mm increments with height adjustment in the beams. Front overhang on the front wall for operation under a tarpaulin up to a total height of approximately 4,400 mm. Four rows of stackable approximately 150 mm aluminum slats on the sides, with 450 mm pockets at the bottom and 4 rows of single pockets above. In the upper bed, only 3 rows of insertable slats. Spacing between slats evenly distributed. Floor: Approximately 27 mm special water-resistant glued beech plywood, rough surface. Steel sheet in the wheel arch area. Forklift drivable according to DIN standard. Outer frame flush with the surface. Brakes: WABCO air brake system with EBS according to EC standard 71/320 EEC including PREV (parking release safety valve). Spring-loaded brake cylinders as parking brake. Wabco Smart Board with odometer and unit load indicator. Includes WABCO tire pressure monitoring system. Axles: 4 x 10,000 kg SAF/Sauer with drum brakes in low-bed design. Air suspension with lifting and lowering device, total lift approximately 230 mm. Third and fourth axles as friction-jointed trailing axles with electrical and mechanical lock. Twin tires: 235/75 R 17.5, -16-ply. Manufacturer of our choice, including E-wheel holder. Without E-wheel. Lighting: according to EC standard including side lights in LED design. Position lights in LED design. 2 additional reversing lights. 2 work lights on the front wall inside, at the top. Painting: Chassis and superstructure in a single color in the RAL color of your choice. Center beams, axles coated with KTL (cathodic electrodeposition) in black. Corner beams in hot-dip galvanized design. Plastic parts in black. Hot-dip galvanized parts unpainted. Rims in factory silver. Special equipment included: - E-supply cable 15-pin - Air suspension in ECAS design, operated on the semi-trailer - Overwidth signage at the front and rear in zinc-plated, continuously telescopic design with attached boundary lights including so

Condition: new, maximum load weight: 90,700 kg, overall weight: 1,26,000 kg, axle configuration: > 3 axles, total width: 2,850 mm, Equipment: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Extract from the specifications. Complete equipment list available upon request. Gooseneck: Gooseneck hydraulically liftable/lowerable and detachable. Length approx. 3,650 mm. For tractor units: 6x4 or 8x4 3-axle compact front bogie: * Hook mounts at the front and rear. Length: approx. 3,560 mm * Chassis width: approx. 2,850 mm Lowbed: * Lowbed ATX-A with telescopic longitudinal beams in low design with fixed hardwood floor approx. 50 mm thick * With drive-over bridging hooks at the front and pin-lug coupling at the rear * Base width: approx. 2,850 mm, Length: approx. 7,150 mm, Beam height: approx. 330 mm, Beam width: approx. 750 mm * Loading height approx. 480 mm with ground clearance approx. 150 mm 5-axle rear bogie: * Mechanical pin-lug coupling for mounting a lowbed at the front, rear end traverse at the back * Chassis width: approx. 2,850 mm * Chassis length: approx. 6,840 mm * Pendle axle 3-axle front bogie: * PENDLE-AXLE, all axles hydro-mechanically forced steered * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off cocks and lock pins for securing in raised position * Final painting of axles with 2 coats of 2-component paint, single color in MB7350 Novagrau * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Front bogie tires: 12 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J 5-axle rear bogie: * PENDLE-AXLE, all axles hydro-mechanically forced steered * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off cocks and lock pins for securing in raised position * Final painting of axles with 2 coats of 2-component paint, single color in MB7350 Novagrau * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Rear bogie tires: 20 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J Paintwork: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure optimal corrosion protection * Final coat with 2 layers of 2-component topcoat, single color in RAL 3002 Carmine Red, according to RAL system 841GL Includes accessories: * Steel front bulkhead, approx. 400 mm high * Plug-in ALU side and rear boards on the gooseneck, approx. 400 mm high, anodized finish * 3.5 kingpin * BEKA-MAX central lubrication for one gooseneck * Multi-coupling hydraulic connections at the gooseneck * Front bogie with a separate air connection for pneumatic screwdriver * BEKA-MAX central lubrication for a 3-axle bogie * Preparation for mounting of bolt-on container locks for 1 x 20' or 1 x 30' containers on the outer beams * Without container locks * Mounts for foldable extensions outside on the outer beams of the loading area * One 7-pin socket left and right, front and rear on the rear bogie for warning signs * BEKA-MAX central lubrication for a 5-axle bogie * Socket on the rear bogie for the cable remote control of the steering override * Rear bogie with trough Gsdjw Tgp Djpfx Ap Dskc * 2 LED reverse lights mounted on the rear panel * European reflector panels (red-yellow) at the rear * One mud flap at the rear * One LED beacon with bracket left and right on the rear traverse * Two INOX toolboxes 855 x 340 x 390 mm on the gooseneck, left and right * 1-cycle

Condition: new, maximum load weight: 36,937 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Year of construction: 2026, Equipment: ABS, Kässbohrer low loader with hydr. gooseneck Available immediately! TECHNICAL DATA: * Semi-mounted height 1,250 mm * Outer length 13,190 mm * Gooseneck length 3,950 mm * Platform length 9,240 mm * Platform height 875 mm * Wheelbase 8,480 mm * Wheelbase 1,360 mm * Axle load 30,000 kg * BPW axles with air suspension and drum brakes, 10 tons load capacity * Unladen weight 11,063 kg * Overall width 2,550 mm * Permissible gross weight (60 km/h) 52,800 kg * Permissible gross vehicle weight (80 km/h) 48,000 kg CHASSIS: * 2x rigid axles at the front, 1x self-steering axle at the rear * Overload-dependent manual axle lift system on the 1st axle * 12-wheel tires 245/70R17.5 * Air suspension, 1x load pressure gauge CHASSIS: Made of high-quality and high-strength S700 MC steel * Gooseneck with 90° vertical corners * Jost supports at the front * Folding rear supports * Grid floor RAMP: * Drive-on ramp capacity 40 tons * 2x hydraulic ramps, suitable for hydraulic sliding/folding operations with galvanized steel surface, 4,200 mm length and 850 mm width, 9 degree ramp angle, load capacity 40,000 kg and 3,510 mm height in closed position * Hydraulic gooseneck ramp 2,800 mm long 10° angle LOAD SECURING: * Lashing rings 6x2 on the gooseneck with 6 tons capacity, 6x2 on the platform with 6 tons capacity, 8x2 on the outer frame with 6 tons capacity * 8x2 stanchion pockets MISCELLANEOUS: * 1x rotating beacon * 1x work light * 2x2 extra-wide boards with lighting Gkodpfxsw Ii A Ao Ap Dec * SmartBoard For further information please do not hesitate to contact us

Condition: new, maximum load weight: 36,937 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Year of construction: 2026, Equipment: ABS, Kässbohrer low loader with hydr. gooseneck Available immediately! TECHNICAL DATA: * Semi-mounted height 1,250 mm * Outer length 13,190 mm * Gooseneck length 3,950 mm * Platform length 9,240 mm * Platform height 875 mm * Wheelbase 8,480 mm * Wheelbase 1,360 mm * Axle load 30,000 kg * BPW axles with air suspension and drum brakes, 10 tons load capacity * Unladen weight 11,063 kg * Overall width 2,550 mm * Permissible gross weight (60 km/h) 52,800 kg * Permissible gross vehicle weight (80 km/h) 48,000 kg CHASSIS: * 2x rigid axles at the front, 1x self-steering axle at the rear * Overload-dependent manual axle lift system on the 1st axle * 12-wheel tires 245/70R17.5 Gedpfxjw Nlzqe Ap Dskc * Air suspension, 1x load pressure gauge CHASSIS: Made of high-quality and high-strength S700 MC steel * Gooseneck with 90° vertical corners * Jost supports at the front * Folding rear supports * Grid floor RAMP: * Drive-on ramp capacity 40 tons * 2x hydraulic ramps, suitable for hydraulic sliding/folding operations with galvanized steel surface, 4,200 mm length and 850 mm width, 9 degree ramp angle, load capacity 40,000 kg and 3,510 mm height in closed position * Hydraulic gooseneck ramp 2,800 mm long 10° angle LOAD SECURING: * Lashing rings 6x2 on the gooseneck with 6 tons capacity, 6x2 on the platform with 6 tons capacity, 8x2 on the outer frame with 6 tons capacity * 8x2 stanchion pockets MISCELLANEOUS: * 1x rotating beacon * 1x work light * 2x2 extra-wide boards with lighting * SmartBoard For further information please do not hesitate to contact us

Condition: new, maximum load weight: 36,156 kg, overall weight: 45,000 kg, axle configuration: 3 axles, Year of construction: 2026, MAX200-N-3A-13.60-19.5-2.54 Gsdpfxsg Sk Tvj Ap Dekc Technical Data Speed: 80 km/h Total weight: 45,000 kg Fifth wheel load: 18,000 kg Axle load: 27,000 kg Unladen weight (+/- 3%): 8,844 kg Payload approx.: 36,156 kg Loading area length: 13,600 mm Fifth wheel height, loaded: 950 -> 1050 mm Rear overhang: 2,300 mm Extendable by: 3,400 mm Wheelbase: 1,360/1,405 mm Overall width: 2,540 mm Technical Description Loading area: Extendable loading platform with pneumatically operated locking mechanism. 2 pairs of lashing rings (LC 5,000 daN). 1 pair of lashing rings (LC 10,000 daN). 6 pairs of lashing rings, foldable outwards (LC 5,000 daN). 2 pairs of lashing rings, foldable outwards (LC 10,000 daN). Cutouts in the outer frame of the loading platform for attaching lashing straps (LC 2,000 daN). Fifth wheel: JOST fifth wheel (mechanical) with 2-speed gearbox for 24t Load capacity (50t test load). Axles: SAF axles: SAF CD axles, air-suspended, with disc brakes (377 mm), with lift/lower function (ET 120). The trailing axles with electro-magnetic reversing lock can be activated via reverse gear or manually. Axle tool. (± 80 kg) Braking system: Braking system according to EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit. Steel construction: Steel construction made of high-strength fine-grained steels. Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Painting: First-class and durable corrosion protection of the standard shot-blasted welded frame is guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) topcoat, solid color, in RAL colors of your choice. Rear section metallized and painted in RAL 9010 (pure white). Metallic paint is not possible. Electrical system: Electrical system according to EU regulations, lighting LED 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the connection strip at the front with 24N, 24S & 15-pin sockets. Connection according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Included Accessories Yellow-red air couplings on the galvanized connection strip at the front. 2 chocks with holders. 2" King Pin A galvanized steel front panel approx. 2200 mm high. (± 105 kg) EN12642-XL Yellow reflector tape according to EU regulations on the side, on the extension and at the rear of the trailer. European reflector signs (red-yellow) at the rear of the trailer. Loading area with approximately 38 mm thick hardwood floor. (± 320 kg) 10 pairs of pocket rails for plug-in rails 100 x 50 mm in the outer frame of the loading platform. (± 30 kg) 1 spare wheel holder under the loading platform on the right side, in the direction of travel. Tires 435/50 R 19.5, at the manufacturer's choice. One mudflap at the rear of the trailer. Manual and description on a USB stick. One mounting for a rotating beacon at the rear of the trailer. On the swan neck and at the rear panel, left and right, one mounting each for warning signs including socket. One INOX tool box transversely under the loading platform (1000x400x2500) (± 135 kg) 6 pairs of WADER container pockets in the loading area, for 1x20' container, 2 x 20' containers or 1 x 40' container; an additional locking point is provided in the extension for a 45' container. (± 90 kg) 4 pairs of WADER container locks. (± 60 kg) 10 pairs of galvanized plug-in rails approx. 100 x 50 mm, 1,000 mm high. (± 220 kg) 3 pairs of pocket rail strips, mounted transversely in the loading area, for plug-in rails 100 x 50 mm. (± 95 kg) S

Condition: new, maximum load weight: 48,300 kg, overall weight: 71,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available for immediate and short-term delivery, on our website. Extract from the equipment features. Full specification available on request. Gkjdpjyhkqnjfx Ap Dec GOOSENECK: * Gooseneck with integrated 1-axle running gear (pendulum axle) in detachable design * Gooseneck hydraulically liftable and lowerable, including hydraulic coupling connected with the hydraulic axle compensation of the first axles * Length: approx. 5,200 mm, with a front taper of approx. 60° * Saddle load according to data sheet: W25-DSR2700-12/22.7 * For tractor units: 6 x 4 or 8 x 4 * Front bulkhead made of steel, detachable, approx. 400 mm high, with chamfered design * 1 pair of mechanical supports at the front of the gooseneck * ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets * 1 spare wheel holder inside on the front bulkhead of the gooseneck with lifting arm * 2 pairs of recessed lashing rings on the gooseneck (LC 2,500 daN) * 2 pairs of recessed lashing rings in the outer frame of the front chassis, foldable outwards (LC 10,000 daN) * 1 pair of lashing rings at the transition between chassis and loading platform (LC 10,600 daN) * On the gooseneck, 1 pair of plug-in side aluminium drop sides, approx. 400 mm high, anodized finish * On the gooseneck, 1 plug-in aluminium tailboard, approx. 400 mm high, anodized finish * 3.5-inch king pin * TPMS tire pressure monitoring system compliant with ECE R 141 * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) * 1 INOX toolbox with 1 lid, mounted on top of the gooseneck on the right in the direction of travel near the aluminium drop side, approx. 1,350 x 400 x 400 mm (L x W x H) LOADING AREA: * Lowbed with external main beams, designed as a telescopic loading platform in low-profile layout with front extension including a fixed approx. 50 mm hardwood floor * Length x width approx. 8,000 mm x 2,740 mm * Mechanical pin-lug coupling from the lowbed to the chassis to exchange the platform or install extension beams * 1 locking position every approx. 500 mm in the extension section * 4 pairs of recessed lashing rings arranged lengthwise on the loading area, distributed along the outer frame/main beam (LC 10,000 daN) * 1 lashing ring per side on the outside of the rear crossmember (LC 10,000 daN) * Foldable widening sections, approx. 230 mm per side (WITHOUT timber planks) * Detachable widening planks, steel-edged * Preparation for installation of bolt-on container positioning devices for 1x 20' or 1x 40' container on the main beams. Container locks not included * 6 pairs of threaded blocks between the lashing rings under the upper flange on the main beam for mounting screw-type M24 rings (LC 8,000 daN) * 2 pairs of M24 screw rings (LC 8,000 daN) included REAR RUNNING GEAR: * Rear running gear with closed external frame, checker plate decking and continuous prism-shaped excavator recess, approx. 1,450 x 900 x 505 mm, open at rear * Pendulum axle, all axles hydro-mechanically forced steered * Hose burst valve on the axle compensation cylinders with automatic reset function * Hydraulic cylinders with shut-off cocks and pre-insertion facility for securing in raised position * Final paint on axles in 2 coats of 2-pack paint, solid colour DB 7350 Novagrau * Technical axle load: 12,000 kg each * Hydraulic axle compensation * 245/70 R 17.5 3PMSF. Brand at our discretion * Remote steering from front and rear via cable-control, with axle alig

Condition: new, maximum load weight: 43,929 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, loading space length: 16,690 mm, loading space width: 2,550 mm, total width: 2,550 mm, total height: 3,570 mm, Year of construction: 2026, Equipment: ABS, Kässbohrer K.SLA R 4 / 2N ? 18/40 Low-Loader Extendable with Wheel Wells (NEW) ---- Equipment & Highlights Technology & Construction - Extendable low-loader trailer with wheel wells - Overall length: 13,190 mm; platform: 9,240 mm + 3,500 mm extension - Platform height only 875 mm for a low loading height - Total width: 2,550 mm + 600 mm extension Gkjdsx Ix Rqspfx Ap Dec - Unladen weight approx. 14,071 kg - Perm. total weight: 58,000 kg (80 km/h) / 63,800 kg (60 km/h) Chassis & Axles - 4 BPW axles: front 2 rigid, rear 2 self-steering axles - Lift axle (automatic + manual) - Air suspension with load gauge - WABCO EBS 4S/3M, ABS & RSS - WABCO Smartboard (axle load, suspension, diagnostics) - 16x tires 245/70 R17.5 (M+S + 3PMSF) - Tire pressure monitoring system per R141 Ramps & Loading Area - Foldable 40-ton ramps - Ramp length 2,750 mm, width 850 mm - Hydraulic sliding system - 45 mm hardwood floor + steel chequer plate over wheel arches - Wheel wells and bridging plates included - Excavator arm recess at the rear Load Securing - Extensive lashing points: - 2×2 lashing rings 5,000 daN & 1×2 lashing rings 10,000 daN at the gooseneck - 3×2 lashing rings 5,000 daN & 4×2 lashing rings 10,000 daN on the platform - 8,000–10,000 daN at the outer frame / wheel well area - 5×2 stake pockets, detachable stakes 50×100 mm - Container locks for 1×20 ft or 1×30 ft Equipment & Comfort - 1× toolbox (700×400×360 mm) - Stake box - Beacon light - LED side marker lights, LED work lights - Wheel chocks - Width indicator panels with LED - Standard 2" kingpin - Metallised chassis (Zn/Al 85/15) – high corrosion protection - Colour: Red ---- Special Features - New & immediately available - High payload, extremely versatile - Perfect for machinery transport, construction equipment, vehicles, etc. - Very robust design, high-quality BPW components We are happy to provide further information on request.