Used Pramac Other for sale (21,141)

Condition: used, Year of construction: 2021, functionality: fully functional, Dürr Ecopure VAR 2206 Thermal Oxidizer with Flue Gas Cleaning (2021) For burning liquid and gaseous waste streams including fluorinated gases, e.g. PFAS, and recovery of aqueous hydrogen fluoride Emissions limits SO2 ≤ 100 mg/Nm³ NOX ≤ 30 mg/Nm³ CO ≤ 50 mg/Nm³ CF4 ≤ 70 mg/Nm³ HF ≤ 1 mg/Nm³ NH3 ≤ 2 mg/Nm³ Comprising Direct fired thermal oxidizer Hot gas cooling and acid recovery Alkaline wet scrubber Honeycomb selective catalytic reduction deNOx system >1M cost spare parts Direct fired thermal oxidizer Including 2x natural gas combustion chambers and burners - High calorific liquid waste requires safe ignition supplemental hydrogen supply for acid formation - Gaseous waste streams injected via nozzles downstream and close to the burner - 1.5MW multi-fuel natural gas & liquid waste (minor fuel stream) burner with natural gas capacity up to 200Nm3/h - 1400C normal, 1540C max allowable temperature destruction of pollutants to reduce emissions with 3.28 MW thermal energy transfer - 2 seconds minimum residence time in combustion chamber at 1400C - 1,800mm combustion chamber internal dia. - Approx 300mm refractory lining Ljdpoz Ai Tpjfx Abyshl - 2,400mm combustion chamber external dia. - 12,000mm combustion chamber internal length - 3.28MW maximum thermal capacity - 4,900Nm3/h, 60mbar, 14kW combustion air fans One chamber is active, the other one is on standby and can be prepared, repaired, or maintained. This allows minimizing shutdown and changeover time to only several days Wet scrubber hot gas cooling and acid recovery SGL Carbon Diabon HT-PQ 850 graphite pipe quencher - 6,000 Nm3/h capacity flow - 1,100 mm dia. - 2,000mm high - pumps SGL Carbon Diabon THX-RS falling film absorber shell & tube heat exchanger - 1,100mm dia. - 4,500mm tube length - 595 no. tubes - 22mm tube internal dia. - Graphite, carbon steel - pumps Quench vessel - PP/FRP - 1,100mm dia. - Approx. 6,000mm high 2x Scrubber absorber columns, each - Shell FRP/PP - Internals PP - 1,000mm dia. - 11,000mm high - Pumps - Dosing station FRP 5m3 Emergency water tank - 1,600mm dia. - 3,000mm high - 3kW heating 2x Teblick 100,000L HDPE hydrofluoric acid tanks (2019) Honeycomb selective catalytic reduction deNOx system - 5,900Nm3/h, 130mbar, 42kW induced draft fan - 320 kW gas/gas heat exchanger - 500 kW capacity reheat burner - 1.2m deNOx honeycomb catalyst Clean gas outflow Stack with flow & temperature measurement Spare parts include - 200 items of sensors, pumps, valves, gaskets, joints etc. - Graphite quencher - Falling film absorber With the redesign and maintenance support of Dürr, the system could also - be adapted to other halogenated gases with bricks to be selected according to gas application - cope with the presence of VOCs or contaminated air - larger volumes with the addition of a small lance for 15kg/h liquid injection

Year of construction: 2003, condition: good (used), functionality: fully functional, Highly Automated CNC Pipe Bending Cell: Rosenberger RB20 Typical Applications The RB20 series is designed for the cold bending of pipes with one or more bends. It is used in industries such as the automotive industry, furniture manufacturing, and plant engineering, where precise, repetitive bends are required. Lhjdezz Hn Iepfx Abyol Technical Features and Function Type: ROSENBERGER RB20 (manufactured in 2003) Performance & Geometry: Servo-electric precision drive with a cold bending capacity of up to Ø 20 x 1.5 mm in steel. High flexibility thanks to freely selectable bending planes within the 78 mm die height and generous 3-axis travel ranges (X/Y/Z: 260 × 146 × 1,170 mm) Control Technology: The logic is managed by a robust Siemens Simatic S7-300 PLC, paired with an industrial operator panel from B&R Robotic Automation: Fully automatic handling (loading/unloading) via an integrated Motoman industrial robot, complete with XRC controller and the corresponding teach-in terminal for path programming. Product removal is carried out reliably via a discharge conveyor belt. Marking system (upgraded in 2021): A modern, high-performance VideoJet 1860 inkjet coder (manufactured in 2021) with microprocessor control enables direct product marking (e.g., lot numbers or barcodes) immediately after the bending process System Safety & Peripherals: CE-compliant safety measures via a SICK safety light curtain and a perimeter safety fence. Optical status indication via R

Condition: excellent (used), Year of construction: 2010, Tekol / Trumpf Laser Welding System Tekol LAP S4 with TRUMPF TruPulse 44 and TBH GL230 Extraction Unit Description: For sale is a professional laser welding system Tekol LAP S4 equipped with an integrated TRUMPF TruPulse 44 pulsed Nd:YAG laser and TBH GL 230 extraction and filter unit. This system is an enclosed precision laser welding station designed for fine, pinpoint, and low-distortion welding of metal components. The pulsed laser enables highly controlled heat input, clean weld spots, and reproducible results. Ideal for precision engineering, toolmaking, repair welding, prototyping, and small series production. Enclosed safety housing with protection system, control panel, rotary indexing table, and extraction/filter system. Technical Data – Tekol LAP S4 Operating voltage: 400 V ~ N / PE Mains type: 3~ 400 V, 50 Hz Nominal current: 32 A (approx. 22.5 kVA) Control voltage: 24 V DC Dimensions: Length: approx. 1330 mm, Depth: approx. 1300 mm, Height: approx. 2030 mm Weight: Machine: approx. 800 kg Travel: X-axis: approx. 160 mm Y-axis: approx. 100 mm Z-axis: approx. 100 mm Rotary indexing table: 2-station Lhedpfszizpcex Abysl Technical Data – Laser TRUMPF TruPulse 44 Laser type: Nd:YAG pulsed laser Wavelength: 1064 nm Max. average power: 42 W Min. pulse power: 201 W Max. pulse power: up to 3 kW Pulse duration: 0.2 – 50 ms Max. pulse energy: 30 J Max. pulse frequency: up to 900 Hz Beam parameter product: 16 mm·mrad Technical Data – Extraction Unit TBH GL 230 Voltage: 230 V / 50–60 Hz Power: 0.36 kW Free-blowing air volume: approx. 390 m³/h Effective air volume: approx. 330 m³/h Max. negative pressure: 4000 Pa Sound level: approx. 51 dB(A) Weight: approx. 40 kg Multi-stage filter system: - Pre-filter - Particle filter - Activated carbon filter Total weight approx. 900 kg Condition: used Scope of supply: (see photos) - Tekol LAP S4 laser welding system - TRUMPF TruPulse 44 laser unit - TBH GL 230 extraction unit - Documentation / folders / data carriers - Keys and accessories as shown (Specifications and technical details are subject to change and errors!) If you have further questions, please feel free to contact us by phone.

Condition: used, power: 67 kW (91.09 HP), next inspection (TÜV): 02/2027, Year of construction: 2005, operating hours: 9,560 h, Equipment: air conditioning, all wheel drive, cabin, German tractor, in use until recently. Second owner, both times government park administration: from 2005 to 2017, and from 2017 to 2026. All-wheel drive. 4-cylinder turbo diesel engine with 4485 cc and 91 hp. Large 24-speed Hi-LO transmission, 4 gears in 3 ranges, 2 powershift stages, and powershift reverser. 40 km/h maximum speed. Air brake system. Comfort cabin with air-suspended driver's seat and air conditioning. Rear PTO with 3 speeds (540/750/1000 rpm). Category II rear hitch with quick couplers and auxiliary lift cylinders (5060 kg capacity). Quick-adjustable height towing hitch. 2 mechanical control units (switchable between single- and double-acting). Front PTO and front hydraulics were retrofitted to the new tractor in 2005. Unladen weight: 4,250 kg. Permissible total weight: 6,200 kg. Registration as "LOF agricultural tractor". Transport dimensions: length 4.36 m / width 2.29 m / height 2.64 m. Front tires: 360/80R24. Rear tires: 440/80R34. All tires are in good condition. According to the vehicle registration supplement, various alternative tire combinations are permitted. Lodpoy Ean Sofx Abyohl The tractor is operational; deregistration scheduled for 16.04.2026. Inspection (TÜV) valid until 02/2027. This offer is only valid for commercial businesses, farmers, foresters, and similar self-employed individuals. Secondary occupation is sufficient. The offer is also valid for government agencies. Sale to private end consumers is strictly excluded. Subject to prior sale and possible errors. Net price: €20,900.

Condition: used, mileage: 33,153 km, power: 124 kW (168.59 HP), first registration: 08/1990, overall weight: 7,490 kg, fuel type: diesel, color: red, gearing type: mechanical, loading space width: 2,430 mm, loading space length: 3,000 mm, loading space height: 1,600 mm, Year of construction: 1990, total length: 7,700 mm, total width: 2,480 mm, total height: 3,000 mm, number of seats: 9, Equipment: all wheel drive, parking heater, In good condition and fully functional, with no pending repairs. +++ Vehicle is ready to drive ++ Power steering ++ 7.5 tons possible with an H-certificate +++ Recent inspection including brake fluid change, lubrication, and fuel filter replacement. In addition, the air dryer cartridge and windshield wipers will be replaced. Both starter batteries have been renewed, and the fluid levels of all components have been checked and topped up if necessary. The windshield washer system will be upgraded to an electric pump with a push-button. The exhaust system will be overhauled, with the last pipe being replaced. This 1113 runs very well and is ready to drive without any issues. 9 seats (6 seats possible with private registration as a truck), All-wheel drive 4x4, central and rear differential locks, trailer hitch with ring eye 1.5t Transfer case with off-road reduction and differential locks, Walk-in equipment box with equipment holders, Wheelbase 4200 mm +++ Maximum speed according to documents = 85 km/h, actual speed with GPS 88 km/h Interior cabin dimensions from behind the driver's seat LxWxH in mm: 1560 x 2180 x 1460 Exterior box dimensions LxWxH in mm: 3130 x 2400 x 1500 Interior box dimensions LxWxH in mm: 3050 x 2400 x 1450 Lhsdpjzmqncefx Abyol GVWR is 9.0t - Changes, prior sales, and errors excepted - ?080?

Year of construction: 2002, condition: used, Empty weight: 2.700 kg Dimensions (LxBxH): 750 x 360 x 230 cm Serial number: 302900081.0 Equipped with an automatic stop system and safety guardrail. Brand: MPS Type: Powerstop Year of manufacture: 2022 Conveyor length: 6200 mm Conveyor width: 630 mm Danobat information: Cutting capacity: 440x440 mm Weight: 2,700 kg Power: 75 kW Equipped with: automatic chip removal Setup dimensions (LxWxH): 7,500x3,600x2,300 mm Online auction of construction, welding, and metalworking machinery and tools (e.g., DANOBAT, BOMAR, WORTELBOER, FRONIUS, ADK, LINCOLN, etc.), as well as vehicles (various LINDE and STILL forklifts, 4 Mercedes Sprinters, 2 VW TRANSPORTERs, etc.), transport and material containers, and office inventory originating from the recent bankruptcy of MOB Mechanical Contracting BV in Rotterdam, the Netherlands. The online auction opens Friday 11 September and closes Wednesday 30 September. Register your account via our website and place your bid. For viewings and inspections check the auction information on the website. Lhjdpfx Asz Ah Dtjbyel Viewing day is on: - Monday 28 September Pickup days are on: - Monday 12 October - Tuesday 13 October - Wednesday 14 October Dome Auctions is an innovative auction platform dedicated exclusively to the industrial sector. By focusing on machinery sales from business closures, restructurings, and bankruptcies, we provide a trusted marketplace where buyers and sellers connect with confidence. Unlike general auction houses, Dome Auctions specializes in selling complete industrial assets directly from factories, ensuring quality and reliability. With a commitment to transparency, industry expertise, and tailored service, we streamline the sales process and maximize value for all parties. As online auctions continue to grow in the European industrial market, Dome Auctions offers a professional and efficient solution for companies seeking high-quality machinery at competitive prices.

Year of construction: 2001, condition: good (used), Heavy-duty scale, scale, parcel scale, weighbridge, floor scale, pallet scale, platform scale, drive-through scale, vehicle scale, drive-through scale -Manufacturer: OAS, Heavy-duty scale, floor scale, pallet scale, bar steel scale -Type: SWT -Weighing range: up to max. 1500 kg -Platform: 2000 x 1500 mm Lodpfx Aoz D T Abjbyjhl -Transport dimensions: 2000/1500/H360 mm -Empty weight: 310 kg

Condition: like new (used), functionality: fully functional, Year of construction: 2006, For sale is a Strojstav MPCS 4 dry shotcrete and guniting machine that has never been used and is in like-new condition (Year of manufacture: 2006). This high-performance machine has 0 operating hours and has been stored securely, offering the build quality and performance of a brand-new machine at a highly competitive price. It is designed for transporting and applying dry concrete mixtures and refractory materials. Ledpfsz Akvrjx Abyshl Technical Specifications & Features: Condition: Like new / Never used (0 operating hours) Year of Manufacture: 2006 Application Method: Dry shotcrete / guniting (pneumatic dry conveying) Feeding Options: Supports standard bagged materials or large-volume Big-Bags using an auxiliary feeding frame. Mobility & Chassis: Heavy-duty wheels with a front-steered twin-axle system for easy manual positioning on-site. Control System: Integrated, user-friendly control station directly on the machine for safe and precise operation.

Condition: excellent (used), (for processing large plates) Lhedpfx Aoz Eaa Nobyol Equipment / Additional information: The plates are fixed to the table using a vacuum.

Condition: used, Year of construction: 1979, MAN 19 280 F BREINING body FEDERAL Emulsion / Asphalt Sprayer Note: Suitable only for emulsion, not for liquid asphalt! Control panel for the superstructure located in the cab! • Manual transmission • Differential lock • Long-distance cab • 1 bunk • Leaf/leaf suspension • Tyres: 12 R 22.5 (alternative: 315 / 80 R 22.5) • Tank capacity: 6,000 litres emulsion • Burner NEW! • Spray bar foldable on both sides! Errors and prior sale excepted! = More information = Fuel type: Diesel Mileage: 67,000 km Lhjdewmpcnspfx Abysl Applicable material: Asphalt Damages: Damaged vehicle (not drivable)

Condition: used, mileage: 6,580 km, power: 37 kW (50.31 HP), gearing type: mechanical, fuel type: diesel, color: red, number of seats: 1, first registration: 01/1962, Year of construction: 1962, driver cabin: other, Vehicle location: Bovenden, If you have any questions, please call ! Color: red Synthetic leather: red 50 HP Original exhaust (see sample photo, last) available| original exhaust (attached photo, last) available Lhedpfx Aevhhz Hebyol This Master belonged to a large and well-kept private collection. All of the older gentleman's vehicles were stored indoors. Due to its age, he has decided to part with this vehicle. Beautifully preserved, this tractor is waiting for its new owner. ACCESSORIES WITHOUT WARRANTY, subject to alterations, prior sale and errors excepted! - .

Condition: used, mileage: 1,53,000 km, power: 70 kW (95.17 HP), first registration: 12/1992, overall weight: 3,200 kg, fuel type: diesel, color: red, next inspection (TÜV): 12/2025, gearing type: mechanical, Year of construction: 1992, total length: 5,345 mm, total width: 1,975 mm, total height: 2,680 mm, number of seats: 9, Equipment: had accident, parking heater, Original German vehicle. In service with a small municipality until 2026, initially with the fire department and then with the municipal depot. This vehicle has a civilian truck registration as a "closed-body truck" and the papers indicate a total of 9 seats. The vehicle was initially used as a multipurpose vehicle (MZF), and later the municipality's lawnmower was transported in it. Only one bench seat is permanently installed. Two of the three bench seats were not needed in recent years and are included as loose items. The seatbelts and mounting screws are also included in their original condition. A folding table with a radio headset is still mounted on the left side, and an original large fire department first-aid kit is integrated into the interior. Engine: OM 602, 5-cylinder naturally aspirated diesel with 2874 cc. The engine always starts perfectly and initially runs smoothly, but after approximately 20 seconds of idling, the idling performance deteriorates significantly, and smoke starts to appear. When the engine reaches operating temperature, the smoke decreases, and the engine runs smoothly again, almost normally. The engine is either severely worn or has an engine malfunction. No precise diagnosis has been made yet. The vehicle starts immediately and functions well, and the usual engine power was fully available during a short test drive, but we do not guarantee its drivability. A repair is certainly necessary in the short term! For driving short distances or loading onto a RORO ship in the port heading to Africa, this 310 D appears to function without any problems. 5-speed manual transmission. 127 km/h. Ball-type trailer hitch with a 2000 kg braked or 750 kg unbraked towing capacity. Power steering. Lhedpoyx N Hqefx Abysl Original Mercedes/Eberspächer auxiliary heater (operational). Body with individual rust spots; overall, it is still relatively well-preserved due to being stored in a garage for many years. The window of the passenger door is damaged and covered with a film. The paintwork has been repaired in black around the lower part of the vehicle. Apparently, the car was always very well maintained at the fire department, but unfortunately not afterwards! The running board on the sliding door – which is still visible in the photos – has been removed for use on another vehicle and is no longer present. Unladen weight: 2370 kg. Permissible total weight: 3200 kg. Overall vehicle dimensions: Length 5345 mm / Width 1975 mm / Height 2680 mm. The tires (205R14C) are from 2013 and are not porous, with approximately 50-60% tread depth. The vehicle is primarily intended for export or for genuine fans of the Bremen transporter who are looking for a completely unaltered base for restoration. The TÜV (technical inspection) expired in 12/2025 and will not be renewed. We have deliberately kept the purchase price attractive, as comparable vehicles in good condition are now usually sold for twice the price or even higher. A personal inspection is highly recommended due to the defects and can be arranged by appointment. This offer is only valid for commercial businesses, freelancers, and emergency services of all kinds. Unfortunately, sales to private end consumers are generally excluded. Subject to prior sale and errors. The purchase price is gross = net, with no VAT (according to §25a UStG / differential taxation).

Condition: used, Colour: Red Empty weight: 750 kg Lsdpfx Abozrnv Ueyohl Dimensions (LxBxH): 120 x 80 x 7 cm - Documentation available: No - CE certificate present: No - Transport dimensions: 1200mm x 800mm x 75mm (l x w x h) - Transport weight [kg]: 750kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Year of construction: 2007, condition: used, functionality: fully functional, A complete set of machines for the production of PVC joinery – sold as a WHOLE SET ONLY. The set includes the following machines: Lhodpezxdf Eofx Abyjl - CLEANING MACHINE Elumatec EV 834/01 (8340120611 - 11/2007) - MILLING MACHINE Elumatec GF 171/00 (1710821408 - 08/2008) - REINFORCEMENT MACHINE Elumatec ADS 259/11 (2591120214 - 2006) - GLASS BEAD CUTTING MACHINE PERTICI BS771 (05V150 - 2005) - WELDING MACHINE Elumatec ZS 720/00 (7200020800 - 12/2004) All machines are in good condition and fully functional. An industrial vacuum cleaner for PVC shavings is also included as a bonus with these machines.

Year of construction: 1993, condition: used, functionality: fully functional, We offer this used ALMORE Mini calo cutting line for thermal insulation, built in 1993, with a double unwinding unit from Jouanel, in very good working condition. These machines are specialized in sheet metal processing and are particularly suitable for thermal insulation, industrial thermal insulation, and ventilation workshops. Functions include: length cutting, deburring, punching, and profiling. Machine weight: 2 tons. If you have any questions or need further information, please do not hesitate to send us a message or call us. Lhsdpfxez Dtmae Abysl

Year of construction: 1990, condition: used, Controls: Heidenhain 3-axis digital readout, without clamping systems, tools and large table, with small table, machine makes noticeable operating noises, an on-site inspection is possible. Lhedpfjz Ea R Iex Abysl

Condition: excellent (used), Year of construction: 2005, color: other, loading space volume: 25 m³, 2005 VAN HOOL 20FT Tank Container, 24,900L / 2 compartments Compartment 1: 12,450L Compartment 2: 12,450L UN PORTABLE T11 Bottom discharge Steam heating 2MKA VH 316L = Further Information = General Information Year of manufacture: June 2005 Model year: 2005 Dimensions Dimensions (L x W x H): 606 x 255 x 267 cm Weights Unladen weight: 4,340 kg Payload: 31,660 kg GVW: 36,000 kg Functional Body brand: Van Hool 24,720L TC, 2 compartments (11,950L/12,770L), L4BN, IMO1, T11 Number of compartments: 2 Condition Technical condition: very good Optical condition: very good Lhsdsz D T Rfjpfx Abyjl Further information Please contact Arne Honingh for further information.

Condition: used, Year of construction: 2007, operating hours: 1,632 h, Equipment: all wheel drive, In accordance with our "General Terms and Conditions," without any guarantee or warranty, we can offer you the following vehicle on a non-binding basis until the conclusion of the sale, subject to errors, typographical errors, and prior sale: Manufactured 09/2007 Maximum working height 11.70 m Maximum platform height 9.70 m Total operating hours 1,632, with 1,514 operating hours on the new Kubota engine New Kubota engine installed in 2021 for €7,000.00 (net), after which it ran for 118 hours and was kept as a backup unit Platform dimensions 1.42 m x 2.49 m Platform extension 1.50 m Permissible gross vehicle weight 3,475 kg Payload 454 kg For 2 people Overall length 2.72 m x width 1.73 m x minimum height, foldable for off-road use 2.51 m Diesel engine, 4x4 Gradeability 40% Travel speed 0.6 - 6.1 km/h Lifting time with rated load 39 sec Lhedoz A I R Djpfx Abyjl Driving at full height with extended platform Diesel engine mounted on extendable support Platform extension 1.50 m Spring-loaded, self-closing full door Foam-filled tires Tilt sensor with alarm and automatic emergency shutdown Hour meter Overload sensors Price: €9,500.00 (net) All information is provided without any guarantee or warranty. Our "General Terms and Conditions" apply. The place of jurisdiction for both parties for disputes up to a value of €10,000 is the local court of Ludwigslust; for disputes exceeding this value, it is the regional court of Schwerin. Subject to errors, typographical errors, and prior sale.

Condition: used, Year of construction: 2007, operating hours: 2,403 h, * Unladen weight: 1,261 kg Lhedpszq Nw Dsfx Abysl * Power: 18.9 kW * Year of manufacture: 2007 -----Internal vehicle number: 12349 Errors and prior sale excepted.

Condition: used, mileage: 1 km, power: 18 kW (24.47 HP), gearing type: mechanical, fuel type: diesel, color: red, empty load weight: 1,400 kg, first registration: 08/1954, Year of construction: 1954, total length: 2,400 mm, total width: 1,430 mm, total height: 1,250 mm, front tire size: 5.50-16AS, rear tire size: 11,2x24, driver cabin: other, Vehicle location: Bovenden Lhodpevhhy Nsfx Abysl It was extensively and faithfully restored to its original condition at considerable expense and signed by Lamborghini. The vehicle comes from a large collection that was dissolved for health reasons. The DL 25 was one of Lamborghini’s most popular water-cooled tractors. The 2-cylinder engine was manufactured by MWM and then sold to Lamborghini Trattori in 1955. It was produced between 1952 and 1960 in 916 units, and approximately 200 units are known to still exist today. The diesel engine has a displacement of 1750 cm³ and produces 24 hp, with a 4-speed plus reverse gearbox for a top speed of 16 km/h. In 1954, it cost 1,400,000 Lire. This model of the MWM or Lamborghini engine is considered to be the tractor that put Lamborghini on the map and brought him the wealth to become a customer of Ferrari and start the history of Lamborghini Automobili. Artcurial Sale Rétromobile 2017 - Lot 76 Sold for €35,760 Accessories information is provided without guarantee; subject to changes, prior sale and errors!

Condition: used, mileage: 55,449 km, power: 92 kW (125.09 HP), first registration: 11/2006, overall weight: 3,500 kg, fuel type: diesel, color: white, gearing type: automatic, emission class: euro3, loading space width: 1,740 mm, loading space length: 3,350 mm, loading space height: 1,870 mm, Year of construction: 2006, total length: 5,651 mm, total width: 1,974 mm, total height: 2,800 mm, number of seats: 2, Equipment: ABS, air conditioning, central locking, Well-maintained Ford Transit 125 T350 panel van L3/H3 with automatic transmission and shelving system +++ Steering wheel paddle shifters +++ Ex-government vehicle from the German Federal Police, regularly serviced with a full service history. This vehicle was used exclusively to handle breakdowns of fleet vehicles outside the facility. It was always kept in a dry, heated facility and is therefore in excellent condition. Features: - Automatic transmission with steering wheel shift paddles - Air conditioning - ABS - 2 airbags - Individual front seats with armrests - Electric mirrors - Central locking with remote - Rear doors with 270° opening angle - Rear step - Side sliding door with window - High, closed rear wing doors - Roof-mounted rear strobe lights Cargo area: - Wooden flooring with shelving system - 220V external power supply with fuse box and on-board sub-distribution - Roof cutout with Plexiglas insert for daylight in the cargo area Full service history, last inspection at 54,064 km Very good all-season tires from DOT 2018, 7.5/8.0 mm tread depth, no signs of cracking (vehicle was stored indoors, shielded from UV light) Cargo area dimensions: 3350 x 1740 x 1870 mm (L x W x H) This Transit drives well and the automatic transmission shifts smoothly; also an ideal base for a camper conversion. Lhodpfx Ajyumpaebyel +++ Subject to error, modifications, and prior sale +++

Condition: used, Year of construction: 2016, operating hours: 2,000 h, functionality: fully functional, For sale: Mazak EMC 3015 automatic sheet metal loading and unloading system, Extensible Manufacturing Cell. Lhjdpoyh N Rdjfx Abysl A new one costs approximately €130,000. The system is practically new. Used with a machine with 2,000 hours of operation, and only occasionally. Manufactured in 2016. High Column model, compatible with the following Mazak machines: Optiplex, Optiplex Nexus, SpaceGear, Optiplex NEO Maximum sheet dimensions: 3000x1500mm Maximum sheet weight: 900kg. Unloading station: max. 2000kg. Sheet metal loading queue management system.

Condition: used, Year of construction: 2007, operating hours: 2,997 h, fuel type: diesel, power: 74 kW (100.61 HP), gearing type: automatic, overall weight: 6,300 kg, empty load weight: 3,000 kg, first registration: 10/2007, maximum load weight: 3,300 kg, axle configuration: 4x4, number of seats: 1, driver cabin: other, brakes: other, maximum speed: 40 km/h, Equipment: all wheel drive, differential lock, pallet forks, * German machine * First owner * Condition: see photos * Merlo Panoramic P32.6 L * 2,997 operating hours * Lifting height 6.40 m * Load capacity 3,200 kg * Lateral reach 3.40 m * Overall height 2.00 m * Fork tines can be adjusted laterally hydraulically * Hydraulic extension * Hydrostatic all-wheel drive * All-wheel steering can be engaged * Width 2.00 m * Transport length 4.22 m * Grammer air-sprung comfort seat * Joystick control * Towing hitch * Engine Deutz * Type BF4M 2012 * 74.9 kW / 100 hp * Gross vehicle weight 6,300 kg If a new TÜV (technical inspection) is desired, we will be happy to provide you with a quote from our partner workshops. Our offer generally does not include a new TÜV inspection, a new DGUV (German Social Accident Insurance) inspection, a new SP (safety report), or a new UVV (accident prevention regulations) inspection. You can find more trucks on our website under: Lhedpsz D Il Dofx Abyel We speak the following languages: German, English, Polish, Turkish Note: We strongly recommend and offer the possibility of inspecting and testing the goods so that the buyer does not have any false impressions about the condition and suitability. Inspection and testing are possible at any time by appointment and are expressly desired. All information is without guarantee. We are not liable for errors and incorrect information in the offer. The buyer is obliged to independently verify the condition and equipment of the goods/vehicles. Subject to change, prior sale, and errors.

Condition: used, Year of construction: 2006, operating hours: 11,070 h, lifting height: 4,450 mm, fuel type: diesel, mast type: duplex, fork length: 1,195 mm, fork width: 1,800 mm, total height: 3,040 mm, total length: 3,200 mm, total width: 2,000 mm, color: red, Empty weight: 7.000 kg Lifting capacity: 5.000 kg - Year: 2006 - Documentation available: Yes - └ Type Documentation: User manual - CE marking present: Yes - CE certificate present: No - Serial number: H2X394T01696 - Operating hours: 11070 - Lifting capacity: 5000kg - Lifting height: 4450mm - Overhead clearance: 3040mm Lsdpfx Abezwc Tfoyshl - Fork length: 1195mm - Maximum fork width: 1800mm - Minimum fork width: 250mm - Number of wheels: 6 Wheels - Attachment: 3rd valve to fork carriage - Options: Joystick, Half cabin, Work lights, Heating, Air tires - Mast: Duplex - Drive: Diesel - Motor brand: VW - Transport dimensions: 3200mm x 2000mm x 3040mm (l x w x h) - Transport weight [kg]: 7000kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, total length: 50,000 mm, We offer this Nordson automatic powder coating line, in very good condition, manufactured in 2016. It is fully operational, so you can visit it any day to see exactly how it works. It includes a degreasing area with an acid bath, followed by drying/preheating, painting, and polymerization. Lhodpjz Dhk Hjfx Abyjl If you have any further questions or require more information, please do not hesitate to send us a message or call us.