Used End Non-Return Valve Dn100 for sale (19,579)

Condition: not inspected (used), Bluhm Systems Marking Laser Here we offer a Bluhm Systems marking laser. Bluhm Systems marking laser, fiber laser e-SolarMark FL. No functional guarantee (untested). Introduction: The e-SolarMark FL10W and 30W are Class IV lasers according to IEC 825 and EN 60825 standards (standards for applications with end customers). It is designed to be integrated into a system or operated separately with a protective housing. After installation, the laser system must meet the requirements for a product of a specific protection class, according to the aforementioned standards. The e-SolarMark is a laser system for marking and engraving plastics, metals, and films, both stationary and in motion. Technical specifications e-SolarMark description The e-SolarMark system consists of two main components: 1. The marking unit with laser head (scanning head) with focusing lens. 2. The control unit includes the power supply, electronic control system, and firmware for system operation, with I/O slots inside. The e-SolarMark includes a fixed galvo scan head, equipped with a lens for a square marking field with standard dimensions of 70 x 70 mm. Laser specification in standard configuration Laser type: Fiber laser Laser output power: FL2 model: 19W; typical Wavelength: 1062 nm typical Internal modulation: 20 to 80 kHz Scanner head description: Scan head: Two galvanometric mirror scanners with a hard, highly reflective dielectric coating. F-Theta Lens types and their properties: Lens marking field: 70x70 mm to 300 x 300 mm Focal length: B 192 mm Operating environment conditions: Relative humidity: up to 80%, non-condensing Operating temperature: 5 - 40°C Recommended operating temperature: 15-25°C Dimensions W x H x D Laser unit: 122 x 108 x 495 mm Hnodpfx Ahozgci Es Set Control unit: 520 x 380 x 215 mm Cable length, marking/control unit: 3 m Weight, marking unit: 5 kg Weight, control unit: 15 kg Mains voltage 115/230 VAC, 50/60 Hz, single-phase. Power consumption, FL2 model: 450W Type: e-SolarMark FL Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We would be happy to answer any further questions you may have by phone.

Condition: excellent (used), Year of construction: 2001, machine/vehicle number: DN-HB160-250KG, ABUS HB overhead crane system with dimensions of approximately 19 x 4 m (4 m span) Extending the runway rails is possible! Load capacity / lifting capacity: 250 kg - 0.25 tons - increasing the load capacity up to 1000 kg is possible! Hnodpfxszv Ea Se Ah Set Technical data of the system: Crane system with ABUS HB160 rails The system is delivered complete: HB rails, rail connectors, carriages, travel drive in the span, end plates, supports/hangers, etc. Including a 250 kg ABUS chain hoist - lifting height approximately 4 m The crane is disassembled and immediately available. Used condition, see pictures. The item is located in 75053 Gondelsheim. Shipping via freight forwarder or collection by appointment only. Demag KBK1, KBK2, and KBK3 rails are in stock! Other KBK systems are also available. Load capacity: 125 kg - 1600 kg. Please request a non-binding quote for your crane system, specifying the load capacity and dimensions.

Condition: excellent (used), Year of construction: 2021, Semi & fully automatic pallet wrapping machine Manufacturer: Cousins Model: LPSWA-CE (“The Switch Semi2Auto”) Operating mode: Semi-automatic & fully automatic Year of manufacture: 2021/2022 Functions and specifications of the LP-SWA-SERIES Production speed: Up to 35 loads per hour. Load capacity: Maximum load weight: 4,500 lbs dynamic - 10,000 lbs static Maximum load size to safely pass the tower: 67“ x 67” (96“ load diagonal) x 80” H Maximum load size to stay inside the turntable: 46“ W x 46” L (65“ load diagonal) x 80” H Low profile turntable: 65” diameter, laser-cut steel top with all-around deck protection. Maintenance free 54-roller bearing support system. Turntable height 2.813 inches from floor. ANSI No. 50 direct chain drive with chain tensioner. Speed between 3 and 12 rpm with smooth start acceleration Film carriage elevator: 1/2 HP DC motor with variable speed ANSI No. 40, direct chain drive with shock absorber and fall protection Automation functions: Fully electric - no pneumatics required Cousins Smart Engineering has developed the A-Arm, an advanced cutting and holding device. It offers significant productivity gains and safety benefits. This technology is only available on Cousins machines. This unique method of applying and cutting stretch film offers you the following benefits: - Selectable banding function at the top - Stabilizes the load early in the wrapping cycle - Places the film end at the top of the load instead of the bottom - There is no film clamp on the turntable that can be damaged by dirt or operator error - and Also, no slip rings are required to power the turntable, reducing maintenance requirements - Load placement on the turntable is not critical - No air connections or noisy compressors - New automatic load detection safety feature on first rotation detects unevenly or partially stacked top layers and automatically adjusts the A-arm height to avoid obstructions - A-arm fall protection Control functions: Electronic control with LED user interface Wireless start/stop remote control with one transmitter (additional transmitters available) Power off - power on - reset switch and operation indicator Automatic wrapping cycle start/pause with just one button Cycle pause for applying the cover sheets Reinforce the wrapping control for the wrapping center Emergency stop button Turntable jog button Buttons for lowering and raising the film carriage Film tension control (force-to-load) Hnsdpfx Ajwb A N Rjh Set Separate speed controls for raising and lowering the film carriage Variable speed control of the turntable Three-beam automatic load height detection sensor for dark or shiny loads Separate control for 1 to 12 turns top and bottom wrapping Selectable parameters for reduced film tension to wrap the top and/or bottom of the load Non-proprietary UL/CSA approved components A - B - C wrapping program selector with the option of entering and saving individual wrapping parameters for each program Product video 1 Product video 2 Product video 3 Financing through our bank is also possible. komplett-konzept.leasingo.de You can find more items - new and used - in our store! International shipping costs on request!

Condition: used, Year of construction: 2012, The SAC F4TL window manufacturing centre is designed to meet the requirements of modern window production. It enables highly efficient, high-quality manufacturing with minimal setup time and without the need for tool changes. After machining, the workpiece is automatically returned to the operator. SAC F4TL CNC Window Manufacturing Centre – Machining Units Tenoning Side 1. Tenoning carriage 2. End trimming unit 3. Tenoning spindle Profiling Side 4. First profiling spindle 5. Second profiling spindle 6. Glazing bead notching unit 7. Hardware slot milling unit (optional) Feed System Tenoning Side 1. Tenoning carriage • Machining speed: 3–10 m/min • Return speed: 45 m/min • Table size: 290–955 mm • Motor power: 1.1 kW Hedozl D Dnjpfx Ah Ssnt • Fence tilting angle: ±60° 2. End trimming unit • Saw blade diameter: 400 mm • Bore diameter: 30 mm • Motor power: 3 kW 3. Tenoning spindle • Vertical adjustment speed: 5 m/min • Spindle diameter: 50 mm • Spindle length: 620 mm • Vertical travel: 565 mm • Motor power: 7.5 kW • Maximum tool diameter: 350 mm Profiling Side 4. First Profiling Spindle • Spindle vertical adjustment speed: 5 m/min • Spindle diameter: 50 mm • Spindle length: 320 mm • Vertical spindle travel: 295 mm • Horizontal spindle adjustment: 60 mm • Spindle rotation direction: left/right • Motor power: 7.5 kW • Maximum tool diameter: 240 mm 5. Second Profiling Spindle • Spindle vertical adjustment speed: 5 m/min • Spindle diameter: 50 mm • Spindle length: 320 mm • Vertical spindle travel: 295 mm • Horizontal spindle adjustment: 60 mm • Spindle rotation direction: right • Motor power: 7.5 kW • Maximum tool diameter: 240 mm 6. Glazing Bead Notching Unit • Saw blade diameter: 200 mm • Saw blade bore: 30 mm • Horizontal spindle adjustment: 60 mm • Motor power: 2.2 kW Optional Unit 7. Hardware Slot Milling Unit • Motor power: 3 kW • Spindle diameter: 30 mm • Spindle length: 100 mm • Horizontal spindle adjustment: 60 mm • Vertical spindle adjustment: 60 mm • CNC-controlled with 2 vertical positions (maximum difference: 60 mm) • Maximum tool diameter: 190 mm Feed System • Feed speed: 4–20 m/min • Pneumatic workpiece clamping CNC Control and Software • 17" colour LCD monitor • 102-key alphanumeric keyboard • Operating system: Windows XP Professional Options • Hardware slot milling unit • Motorized NC-controlled stop • Return roller conveyor • Leitz IV 69 tool set • Leitz IV 90 tool set This machine is offered for sale on behalf of a customer. Viewing is available by prior arrangement. Please contact us through the platform's messaging system for further information and the relevant technical contact details.

Condition: used, maximum load weight: 36,250 kg, overall weight: 41,000 kg, axle configuration: 3 axles, first registration: 10/2025, next inspection (TÜV): 10/2026, Equipment: ABS, Excerpt from the equipment list. Complete equipment list available upon request. Frame: Chassis frame made of high-quality steel, but without an outer frame. Coupling plate with a 2-inch drawbar eye according to DIN 74080 / ISO 337. With crossmember and container locking mechanisms for accommodating: a) 1 x 45' High-Cube container b) 1 x 40' High-Cube container c) 1 x 30' ISO container, flush at the rear d) 2 x 20' ISO containers e) 1 x 20' ISO container, flush at the rear g) 1 x 45' ISO container h) 1 x 40' ISO container With 1 pair of height-adjustable container locking mechanisms and 3 pairs of foldable center supports, plus crossmember and container locking mechanisms for accommodating: f) 1 x 20' ISO container in the center Frame extension at the rear, mechanically extendable, load capacity approx. 5,800 kg, with spiral cable. Low-maintenance guidance on special plastic sliders and 2 extension rollers. KÖGEL frame extension at the front, manually extendable and mechanically lockable, incl. container guide on the left and right. Designed according to Directive 719/2015. Frame extension in the center, manually extendable and mechanically lockable with the tractor unit. Chassis: Axle lift mechanism on axle 1. Control of the axle lift is fully automatic and load-dependent. Starting aid: Activation via 3x brake, 30% overload up to a speed of 25 km/h. Operation on the chassis via switch. Additionally possible from the cab (switch in the cab necessary - PIN 12). When transporting 30' and 45' containers, the 1st axle CANNOT be lifted! BPW three-axle unit, with disc brakes Ø approx. 430 mm, mounting depth approx. 120 mm. Air suspension with approx. 180 mm travel. Vehicle Tires: Wheels with internal sensors according to UN ECE R141. Tires 6-fold 385/55 R 22.5 UNIROYAL TH 50. 6 steel rims 22.5 x 11.75, mounting depth approx. 120 mm (ET 120). Chassis Components: Hodpezkx Hzsfx Ah Sont JOST landing gears, mechanically operated with leveling foot, 24 t lifting capacity. One-sided operation in the direction of travel, on the right. Splash guard system (spray suppression) according to Regulation (EU) No. 109/2011 for three-axle unit with 22.5 tires, consisting of: 3 pairs of semi-circular fenders with mud flaps. 2 chock blocks with holder. Side protection, according to ECE-R73, closed. Rear underrun protection made of square steel tube according to ECE-R58, screwable. Height of the underrun protection profile min. 120 mm, designed for increased test forces. Brake / Air Suspension System: EBS system 2S/2M with stability program (includes ABS/ALB function), EBS plug connection ISO 7638 (without connection cables), parking brake as spring brake, external pneumatic connections as well as external EBS diagnostic connection via ISO 7638 plug connection. Air suspension system incl. 1 raising and lowering valve, mounted on the left in the direction of travel in front of the axle unit. 2 non-interchangeable coupling heads at the front ISO 1728. Air reservoir for brake system and air supply made of steel (EN 286-2). Rear Impact Protection: Continuous steel rear impact protection, solid, on the end member at the rear. Information Systems: Tire pressure monitoring system according to UN ECE R141. Accessories: Document tube, diameter approx. 105 mm. Mounting on the left in the direction of travel on the side protection. 1 fire extinguisher 6 kg with pressure gauge (European approval). Mounting incl. holder and protective cover on the left in the direction of travel o

Condition: used, This listing is for the Eppendorf Centrifuge 5420 The unit is in full working condition and is ready for immediate use The Eppendorf 5420 is a non-refrigerated microcentrifuge designed for routine molecular biology workflows—especially spin‑column-based DNA/RNA purification, gel extraction, and PCR prep. It offers outstanding performance while saving precious bench space. Key Features & Design Highlights Compact Footprint: Measures just 24 × 35 × 22 cm (W × D × H), or approximately 9.4 × 13.8 × 8.7 in., making it ideal for crowded lab benches. High-Speed Performance: Reaches up to 15,060 rpm, generating a maximum relative centrifugal force (RCF) of 21,300 × g. Large Capacity with Flexibility: Comes standard with an aerosol‑tight rotor accommodating 24 × 1.5/2.0 mL tubes. Optional adapters support 0.2, 0.4, 0.5 mL tubes, 0.6 mL BD Microtainers, as well as a rotor for 32 × 0.2 mL PCR tubes or four 8‑strip PCR sets. Ergonomic Controls: Soft‑touch lid closure—one-finger operation. Automatic lid opening at the end of runs to minimize sample warming and ease access. One‑push short‑spin key—perfect for quick spins without holding the button. Easy‑clean keypad and large, bright LCD display. Low Noise & Safety: Hnjdpfx Ahoxhd Hbj Sst Quiet operation at

Condition: new, working width: 85,000 mm, For enquiries regarding the attachment, please contact Mr. Herden (by phone). Seppi M. H3 085 Mulcher / NEW / in stock & immediately available Price: €6,890.00 net / €8,199.10 gross - Working width: 85 cm - Total width: 97 cm - Depth: 80 cm - Height: 66 cm - Weight: 181 kg - Mulching head for mounting on a hydraulic arm - Mulches grass and brush up to 3 cm diameter - Suitable for excavators from 2 to 5 tonnes - Suitable for mounting on various adapter plates - Floating attachment (parallelogram linkage) - Indirect V-belt drive with 3 V-belts - Drive designed for hydraulic motor, depending on the carrier’s hydraulic flow rate - Housing made from wear-resistant AR400 steel - Front protection with chains - Rear guard made of rubber - Reinforced support roller with double taper roller bearings, height adjustable - Colour: red RAL3020 · anthracite RAL7021 OPT 039 Rotor with SMW flails (standard) - 9 pieces, spare part no. 150.02.041 OPT 428 Hydraulic gear motor 11cm³ - With flow control valve and motor safety valve DRAIN SAFE TM to protect the motor in case of improper use - Required hydraulic pressure in bar (min-max): 150 - 250 - Required hydraulic flow in l/min (min-max): 20 - 50 OPT 529 DRAINLESS system with pressure accumulator (NO leakage oil line required!) - Includes hoses and non-return valve Optional: MS03 adapter plate incl. bolts and installation = €530 net Two hydraulic lines are required: supply and return. No leakage oil line is needed! The unit is supplied without hoses or couplings. Many other adapter plates (MS01 / MS03 / MS08 / CW05 / CW10 / CW20 / OQ65 / OQ70/55 / etc...) in stock and immediately available. We have a large selection of various Seppi M. products in stock, all immediately available! Simply contact us at / . Financing offer available on request. We are official Seppi M. distributor and service partner. We are official Magni telehandler distributor and service partner. We are official DMS distributor and service partner. We are official Westtech distributor and service partner. We are official JCB construction machinery distributor and service partner. We are official Mercedes-Benz distributor and service partner. We are official Iveco distributor and service partner. We are official Holp distributor and service partner. We are official OilQuick distributor and service partner. In addition, with 800 used vehicles, we are one of the largest commercial vehicle dealers in Germany. We supply the complete Seppi M. range for you! Errors and prior sale excepted. Hnjdpfx Ahjyi Ryxj Set = Further Information = Please contact Marius Herden for more information.

Year of construction: 1959, condition: used, The machine has various defects and would require an overhaul, defects: no operating manual, no safety valves for the return stroke (no dual-channel design), no safety valves for ram down, in single-stroke operating mode the stroke is automatically completed once the brake is reached, missing cover/door for the control cabinet, selector switch is not secured, there is a continuous-run operating mode which behaves similarly to the single-stroke operating mode, no simultaneity monitoring for ram down, the safety guard on the rear of the press is not electrically interlocked and can remain open during the press stroke, a large amount of oil in the side frame, valve leaking, the machine is operational. On-site inspection is possible. Hodpfxjzv T Iwe Ah Ssnt

Condition: excellent (used), Year of construction: 2005, machine/vehicle number: TD2002/2360, DEMAG KBK overhead crane system with approximate dimensions of 3x4m (4m span) Hnodpfx Ahjztut No Set This crane is available in multiple units! Other sizes are also available – please inquire! Load capacity / lifting capacity: 800 kg - 0.8 tons Technical data of the system: Crane system with Demag KBK2 rails The system is delivered complete: KBK rails, rail connectors, trolleys, end plates, supports/hangers, etc. The crane has internal power supply Includes 800 kg Demag DKES chain hoist (infinitely variable) - lifting height approx. 3m The crane is disassembled and immediately available Very good condition, see pictures The item is located in 75053 Gondelsheim Shipping by freight forwarder or collection only by appointment Demag KBK1, KBK2 and KBK3 rails are in stock! Other KBK systems are also available. Load capacity 125 kg - 1600 kg Please request a non-binding quote for your overhead crane system, specifying the load capacity and dimensions.

Condition: excellent (used), AVE RRT 24-24-6 Triblock – Automatic Rinsing, Filling, and Capping Machine AVE RRT 24-24-6 automatic triblock in stainless steel, designed to integrate the rinsing, filling, and capping operations of containers into a single machine within industrial bottling and packaging lines for liquid products. Manufactured by AVE, the equipment combines three consecutive process stages in a compact, rotary configuration: hygienic preparation of the container through rinsing, product dosing, and subsequent application and sealing of the cap. The 24-24-6 configuration provides multiple workstations to achieve a continuous flow of containers and reduce transfers between independent machines. MAIN FEATURES Hodpfszxcq Hsx Ah Sent -Manufacturer: AVE -Model: RRT 24-24-6 -Type: Automatic rinsing, filling, and capping triblock -Configuration: 24-24-6 -24 rinsing stations -24 filling stations/valves -6 capping heads -Rotary and continuous operation -Automatic container feed -Synchronized transfer between the different stations -Integrated transport system -Construction primarily in stainless steel -Perimeter enclosure with safety guards -Hygienic design for the food industry -Compact construction for line integration -Designed for continuous industrial production PROCESS Containers automatically enter the AVE RRT 24-24-6 and pass successively through the three main operations. First, the containers are positioned in the rinsing section, where they are prepared before filling. Subsequently, they are transferred to the 24-valve filling section, where the product is dosed. Finally, the containers pass to the 6-head capping station, where the cap is automatically placed and sealed before being discharged to the next stage of production. APPLICATIONS Particularly suitable for manufacturers of beverages, juices, water, liquid food products, and other bottling industries that require concentrating several operations into a single automatic machine. It can be integrated with: Container feeding systems Tanks and product preparation systems Cap feeders Conveyors Pasteurizers Labeling and coding machines Inspection systems Case packers and end-of-line equipment The combination of rinsing + filling + capping in a single AVE RRT 24-24-6 triblock provides a compact solution for automatic bottling and packaging lines. Machine available for inspection. Additional technical information, dimensions, additional photographs, or videos can be provided upon request.

Condition: like new (used), Year of construction: 2025, functionality: fully functional, pressing force: 40 t, table width: 1,000 mm, table length: 600 mm, Hidrobrasil Double Column Press – 40 t – 1,000 × 600 mm – Stroke 500 mm For sale is a hydraulic double column press (H-frame) manufactured by Hidrobrasil, featuring an adjustable pressing force from 6 to 40 t. This machine is designed for calibration, assembly, and small series applications, and stands out thanks to its compact design, robust guidance system, and precise control. Ideal for flexible production processes with changing requirements. ==== Technical data & information: Hydraulic Double Column Press – 40 t ==== General information - Manufacturer: Hidrobrasil - Model: Double Column Press - Design: H-frame / Double Column Press - Designation: Small Batch Press / Calibration Press - Pressing force: 6–40 t (adjustable) - Machine weight: approx. 3,500 kg - Dimensions (L × W × H): approx. 2,100 × 1,600 × 3,500 mm ==== Working area - Max. installation height: 700 mm - Stroke: 0–500 mm (adjustable) - Table height above floor: 800 mm ==== Table & Slide - Table size: 1,000 × 600 mm - Slide area: 1,000 × 600 mm - Guide columns: Ø 100 mm (4 units) - T-slots and holes: as per customer specification ==== Speeds - Rapid traverse speed: 80 mm/s - Pressing speed: 9 mm/s - Return speed: 90 mm/s ==== Hydraulics & drive - Hydraulic pump: ASC, 67 + 8 l/min - Motor power: 4 kW - Total connected load: approx. 6 kW - Operating pressure: max. 260 bar - Pressure accuracy: ± 5 bar - Hydraulic manifold and valves: Duplomatic - Air and oil filters: Filtrec - Electronic oil level switch - Air cooling for hydraulic system - Pressure adjustment via pressure switch - Hydraulic unit mounted at top rear ==== Control & Safety Hedjxrby Hspfx Ah Sont - Control via sensors - Safety light sensors - Safety cover (door) at rear - Work area interior lighting - Pressure display via manometer ==== Electrical - Main supply: 400 V AC - Control voltage: 24 V DC - Frequency: 50 Hz - Components: Siemens, Allen Bradley, SICK ==== Electrical cabinet - Protection class: IP54 - Spare capacity: approx. 30% - Cooling: air cooling - Interior lighting: fitted - Operating mode selector: lockable ===== Calibration, assembly work, small batch production, forming technology, flexible production Hydraulic press, double column press, H-frame press, calibration press, assembly press, industrial press Looking for a hydraulic press tailored to your application? Contact us for a customised offer. Our hydraulic presses are manufactured in accordance with German machinery directives, as well as European machinery directives (Directive 2006/42/EC), EC standards, and EU safety regulations. Furthermore, our presses exceed Canadian and European safety requirements as they fully comply with the Brazilian national safety standard NR 12, which builds upon these. Our key strength lies in special-purpose machine engineering and press automation. We supply customised hydraulic presses at surprisingly competitive prices. All presses are equipped with hydraulic components primarily from leading European manufacturers.

Condition: used, Year of construction: 2005, Single-sided edge bander designed for precise and stable edging of solid wood and panel components (chipboard, MDF, laminate). The machine is conceived as a compact yet fully equipped solution for small- and medium-batch production, with an emphasis on edge processing quality. A robust cast iron frame ensures high rigidity and long-term geometric stability of the machine. It features a classic continuous conveyor with a pressure belt and a complete set of machining units for finishing the edge in a single pass. Technical configuration of the machine: - Pre-milling unit - Material pre-heating - Automatic EVA glue application - EVA glue roller - Front and rear end trimming saws - Rough trimming unit - Corner rounding unit - Radius scraper Hnodpfx Aeyfw Syjh Sjt - Glue scraper - Grooving unit - Brushing unit - Return conveyor

Year of construction: 1973, condition: like new (used), Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls. Year of manufacture : 1973. MACHINE FORMERLY INSTALLED AT ROLLS ROYCE PLC IN DERBY UK. IMMEDIATELY FOR SALE AND NOW LOCATED IN BELGUIM WHERE IT CAN BE INSPECTED. SPECIFICATION CAPACITY Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only". Material Mild Steel Mild Steel Tensile strength 28/32 tons/sq.in 28/32 tons/sq.in Maximum width 11’(3350mm) 11’(3350mm) Hnedpoh U Rzgefx Ah Sjt Maximum thickness at this width 2” (50mm) 2½” (63.5mm) Minimum inside diameter of rolled cylinder at maximum capacity 30’ (762mm) 37 ½’ (953mm) Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.) 4” (102mm) 5” (127mm) Minimum inside diameter of rolled cylinder at maximum capacity hot rolling 40” (1016mm) 50” (1270mm) MAIN PARTICULARS Diameter of all rolls - 27” (686mm) Body length of rolls - 11’2”(3403mm) Rolling speed - 12 f.p.m. (3600mm/min) Main drive motor - 150 H.P. Slip Ring Type Two bottom roll adjusting motors, each - 50 H.P. Slip Ring Type Combined operation of swing down bearing and top roll counterbalance - Hydraulically applied Hydraulic power pack motor - 10 H.P. Electrical equipment to be suitable for operation on a supply of - 400/440 volts, 3 phase, 50 cycles CONE ROLLING ATTACHMENT: To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing. ELECTRICAL EQUIPMENT Motors: Main Drive - 150 H.P. half hour rated – slip ring screen protected – foot mounted type. Bottom Roll Adjustments - 50 H.P. half hour rated – slip ring screen protected – foot mounted type. Hydraulic Power Pack Motor - 10 H.P. continuously rated – Squirrel cage – screen protected – foot mounted type. Control Gear: Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary. Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary. Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station. Solenoid valves for operating cylinders are push button operated. Note: Full protection to be provided for all the above control gear by a circuit breaker, incorporating overload and no-volt protection. FEATURES AND EQUIPMENT Spare Roll included with the machine. LENGTH TBA MM WIDTH TBA MM HEIGHT TBA MM WEIGHT 95 tonnes NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.

Condition: good (used), functionality: fully functional, power: 104 kW (141.40 HP), overall weight: 1,890 kg, fuel type: diesel, color: yellow, Year of construction: 2016, operating hours: 3,735 h, operating pressure: 12 bar, machine/vehicle number: APP402997, - Non-return valve installed Hsdpfeu A Tq Hsx Ah Sjnt - Powder-coated body - Height-adjustable towing device with truck DIN towing eye or car heavy-duty coupling - Overrun and parking brake with automatic reverse function Further information on the enclosed data sheet.

Condition: excellent (used), Year of construction: 2022, machine/vehicle number: 31.07.109.22, functionality: fully functional, operating hours: 1,200 h, power: 3 kW (4.08 HP), input voltage: 230 V, input current: 20 A, input frequency: 50 Hz, type of input current: DC, volume flow: 1,450 m³/h, intake vacuum (max.): 2,400 mbar, suction capacity: 3,200 m³/h, intake manifold diameter: 160 mm, filter area: 20 m², noise level: 70 dB, actuation type: pneumatic, total height: 2,005 mm, total length: 1,775 mm, total width: 898 mm, overall weight: 370 kg, year of last overhaul: 2022, Equipment: CE marking, documentation/manual, PRICING & CURRENCY NOTICE FOR UK BUYERS: Headline price is €5,000 due to platform limits. Actual price is fixed at £4,250 GBP. UK Buyers: Fixed at £4,250 GBP via BACS bank transfer. No conversions. Overseas Buyers: Must clear into our UK bank as exactly £4,250 GBP net of all fees. 📌 COLLECTION LOCATION NOTICE: The machine is NOT at our registered account/billing address. Location: Private workshop just outside West Calder (rural area), West Lothian, Scotland. Access: Ample space and suitable access for vans, flatbeds, and collection couriers. Full Address: Provided directly to the buyer upon formal agreement of sale. Overview & Provenance: For sale due to a complete workshop closure. This premium Felder RL 160 clean-air dust extractor was purchased brand new directly from an official Felder dealership. One private owner from new. Meticulously maintained and looked after in a clean workshop environment. Clear Title & Ownership: Originally financed through Novuna over a 4-year term. All payments are fully complete as of August 2026. The machine is sold with 100% clear title, free from any financial encumbrances or liens. Official settlement confirmation can be shown upon request. Rare Single-Phase Configuration: Factory-built single-phase (230V) machine. Maximum operational current draw of 19.7A (requires a 25A backup fuse circuit, typically running on a 16-amp industrial socket). Ultimate plug-and-play setup for high-end home workshops or sites without 3-phase power. Premium Factory Upgrades & Accessories: • Pneumatic Filter Cleaning: Factory-fitted Jet-Pulse automatic compressed-air cleaning system. Blasts dust from inside filters to ensure maximum, constant suction and extend filter life. Hnsdpozvh Dyofx Ah Set • Integrated Mobile Chassis: Factory heavy-duty caster wheel kit for effortless movement. • Dry-Air Protection Kit: Inline moisture filter and integrated pressure gauge. Ensures air supply is clean, dry, and regulated, fully protecting filters from moisture damage. • Pneumatic Pipework: Extra lengths of plastic compressed-air piping included alongside currently fitted pipework for immediate setup. Technical Specifications: • Certification: H3 Certified (Residual dust < 0.1 mg/m³ for clean indoor workspace air). • Max Airflow: 3,200 m³/h • Intake Vacuum / Negative Pressure: 2,400 Pa • Extraction Port: 160 mm • Filters: Original Felder filters, used but in perfectly fine, clean operational condition. • Noise Level: Exceptionally quiet 70 dB operational sound pressure level. Transaction & Returns Terms: • Price: £4,250 (No VAT to add / Private Sale). • Payment: Strictly via secure Direct Bank Wire Transfer (BACS / IBAN / SWIFT). No PayPal, cheques, or cash-on-delivery couriers. • Shipping: Buyer must independently arrange, insure, and pay for all transport logistics. Machine released only once funds fully clear. • Returns: Private sale. Sold as described with no returns. Viewing and testing under power at the workshop is highly welcomed and encouraged.

Condition: defective spare-parts repository (used), Year of construction: 1980, Machine: Type: BFT 90/3at Manufacturer: UNION Year of manufacture: 1980 Control: NC control, HEIDENHAIN TNC 131 Electrical cabinet: by Reliance Machine group: Table-type boring mill Customs tariff number: 84592100 Technical data: Spindle diameter: 102 mm X-axis travel: 1000 mm Y-axis travel: 1250 mm Z-axis travel: 1600 mm Tool holder: ISO 50 DIN 2048 Spindle stroke: 710 mm Spindle speeds: 8 – 1600 rpm Table size: 1000 x 1120 mm Table rotation: 360° Max. workpiece weight: 2,500 kg Feed ranges: 0.8 – 2,000 mm/min Rapid traverse: 3.15 m/min Feed force: 16,000 N Spindle motor: 11 kW Total power requirement: 23 kW Machine weight: approx. 9.3 t Space requirement: approx. 5.3 x 3.8 x 3.14 m Special features and notes: Electronic issue: There is an electronic problem (control board needs to be replaced). The price has been adjusted accordingly (€10,500.00) to account for the necessary repair work. The HEIDENHAIN contouring control and the mechanical components of the machine are in good condition. Inspection is possible by appointment to assess the machine's condition and the extent of the electronic issue. For further technical details, please refer to the attached data sheet. Hodeygarljpfx Ah Sjnt Important information: All information is subject to confirmation, prior sale, errors, and availability. Technical data and all information provided are non-binding and only for orientation purposes. Contact: If interested or to arrange a viewing, please send a message or make an appointment. Disclaimer: The item is sold as described. Returns, warranty, and guarantee are excluded. The buyer agrees that the item is purchased in its current condition, "as seen," with no right of return. No liability is assumed for the accuracy of the information provided in the text or photos. By purchasing this item, you agree to the above-mentioned terms and conditions.

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, Unicontrol 12 Consisting of: Cut-off unit (item A), Tenon and slotted spindle (item C), Transfer belt (Pos. I), profiling spindle (Pos L), profiling spindle (Pos. N), Profile shaving unit vertical right (Pos. P) For the production of individual parts and elements in frame-by-frame or serial production. Consisting of a cross processing unit and a longitudinal processing unit connected to a transfer belt. Working width 40-140mm (See pressure ruler left 40 - 140 mm) Working height 40-120mm Workpiece length min. approx. 275 mm + 1 x end profile length Long machining: approx. 220 mm + 2 x end profile length Workpiece length max. 3500 mm The part dimensions depend on the machine equipment, production type and tool assignment. A final definition of the part dimensions is only possible after receipt, inspection and approval of the complete and final layout drawings. Cross machining: Table feed Motor power 0.3 kW (0.4 HP) Pre-set feed speed for cutting, profiling and return 3-25 m/min Hnodpfx Ahjumci Ss Set Vario table with (studio window production possible) The clamping length of all tenoning and slotting spindles can be used without a tool blank. Workpiece clamping by means of a clamping bridge. Operated by a clamping cylinder installed under the table. NC-controlled long fence mounted on the slotting table. Studio window device Swivel angle max. +/- 75° The minimum workpiece length for slanted windows depends on the angle and the width of the wood. Possible part dimensions for slanted window production Angle Max. Min. Working width Workpiece length +/-75° 80 mm 800 mm +/-70° 120 mm 490 mm +/-60° 240 mm 360 mm +/-90° 350 mm 185 mm For angles greater than 60° only counter processing Commission not documented 1)NC automatic angle adjustment for machining angled parts Splinter protection by means of overtravel counter Over the entire spindle length of the tenoning and slotting spindle for 90° machining Manually trackable counter-rail for angled part machining 2) Additional counter-rails

Year of construction: 2016, condition: good (used), For inquiries: Zoltán Utasi +36 30 205 7380 • Edging thickness coiled edging: 0,4 - 3 mm • Edging thickness of cut-length edging: o max. 3 mm with unit FF701 Hodpfxjwkf Tws Ah Sent o max. 8 mm without unit FF701 o max. 15 mm possible through tool change at trimming unit • Edge height: max. 65 mm • Workpiece thickness: 8 - 60 mm • Workpiece width: min. 65 mm • Workpiece length: min. 160 mm • Feed speed: variable 10 - 18 m/min LUMINA 1380 Ltronic Motor-driven pressure bridge adjustment Automatic lubrication of the transport chain Preparation RETURN-connection Electric for variable feed 400 V / 50 Hz, 2.2 kW Operation Edge Control 19 with 18,5" Touchscreen ECO MODE power-saving mode Pre-milling unit 1802 with 2 milling units Edge feeder MG701 SYNCHRO automatic transport of roll and strip products Ltronic LT702 NIR+ Laser Edging Unit Glue application system Glu Jet GJ302 automatic motorized, automatic adjustment of gluing height (tracing nozzle) (EVA, PUR) Glu Jet rinse hopper Change carriage GJ302 Change carriage LT702 Pressure section 1913 MOT: first roller driven, 2 support pressure rollers Sprayer unit after pressure unit with use of antistatic coolant End trimming unit1918 (60 mm) pneumatic Form trimming unit FR701: Play-free mechanism and 6 fully digital NC servo-axes ensure Form trimming unit FF701: Play-free mechanism and 4 fully digital NC servo-axes ensure 100% repetition accuracy at the touch of a button. Scraper unit 1929 MOT4 with motor-driven adjustment for sensing rollers Surface glue scraper FK701 With pre and post tracing device for scraping out superfluous glue on the complete panel length for a clean glue line. Sprayer unit1856 for the in- and outfeed area Buffing unit 1940 For edge cleaning and polishing

Condition: like new (used), Year of construction: 2018, functionality: fully functional, saw blade diameter: 450 mm, cutting height (max.): 150 mm, warranty duration: 6 months, Equipment: rotational speed infinitely variable, Kaltenbach KKS 450E – very neat used machine from 2018 with 6 months warranty. Extra options: * Micro-dosing system & wet cooling * Horizontal (hydraulic) clamping cylinder 1 x Hjdpfx Aeyr S Szjh Sjnt The KKS 450E is a semi-automatic mitre saw for ferrous and non-ferrous metals such as: steel, stainless steel, chrome steel, brass, copper, bronze, etc. Benefits at a glance: - Clamping, sawing, reversing and releasing – all with a single lever - Saw height adjustable via a lever - User-friendly mechanical controls mounted directly on the machine - Excellent accessibility for saw blade changes and maintenance - Workpiece clamping device on both sides of the saw blade - Two cutting speeds for virtually all applications - Ergonomically positioned controls for user comfort - Adjustable sawing stroke limitation and rapid saw blade return All pre-owned Kaltenbach machines are supplied with a 6-month warranty as standard. Transport and installation available throughout the Benelux.

Condition: like new (used), Year of construction: 2023, Huber CS 550 OD Cooling Unit / Chiller Manufacturer: Peter Huber Kältemaschinenbau SE Type: CS 550 OD Year of Manufacture: 11/2023 Machine Type: Cooling Unit / Chiller / Process Cooler Cooling Capacity: 55 kW at +10 °C supply / +50 °C return temperature For sale is a like-new Huber CS 550 OD chiller with an air-cooled cooling unit and circulation pump. The unit has not yet been used. The system is suitable for industrial process cooling, machine cooling, chilled water supply, and temperature control applications. The special design is suitable for outdoor installation and winter operation. Technical Data: Model: CS 550 OD Item No.: 32-100110 Year of Manufacture: 11/2023 Temperature Range: -20 to +85 °C Internal Temperature Sensor: Pt100 Temperature Stability at -10 °C: 2 K Interface: RS232 Safety Class: I / NFL Heating Capacity: 17 kW Power Connection: 400 VAC / 50 Hz / 3Ph+N+PE Power Consumption: 27.5 kW Max. Current Consumption: 52 A Refrigerant: R449A Hnodpfx Ahszt Iqzo Sst Refrigerant Quantity: max. 23 kg Max. Operating Pressure: 28 bar Made in Germany Cooling Capacity: According to the nameplate: 55 kW at +10 °C supply / +50 °C return temperature At 20 °C ambient temperature: +15 °C: 70 kW +10 °C: 60 kW 0 °C: 33 kW -10 °C: 20 kW -20 °C: 12 kW Circulation Pump: Pump: CM5-4 Max. Flow Rate: 125 l/min Max. Head: 4.0 bar Pump Connection: G1 male Min. Filling Volume: 160 l Low-Level Alarm: 175 l Max. Filling Volume: 195 l Dimensions: External Dimensions (W × D × H): approx. 1,400 × 1,000 × 1,800 mm Net Weight: approx. 715 kg Sound Pressure Level: 79 dB(A) ± 4 dB(A) Equipment: Air-cooled cooling unit Circulation pump Housing and tank made of stainless steel Copper-brazed evaporator Digital level indicator High-efficiency fan motor Feed pump with over-temperature protection Manual bypass valve Control unit B400 / RB400 Capacitive user interface with OLED display Multi-color status indicator RS232 interface Separate operating/control panel Connection/connecting cables as shown in the pictures Temperature control/connecting hoses as shown in the pictures Connecting fittings as shown in the pictures Electrical components IP54 Outdoor installation / winter operation up to -20 °C Max. Ambient Temperature +50 °C Mobile unit housing Additional accessories as shown in the pictures Transport Data: Unit dimensions: approx. 1,400 × 1,000 × 1,800 mm Net weight: approx. 715 kg Wooden transport crate available. Shipping via freight forwarder possible. Condition: Like new / not yet in use. Year of Manufacture: 11/2023 Optical condition as shown in the pictures. Accessories partially in original packaging or in accessory boxes. Scope of Delivery: 1 × Huber CS 550 OD Cooling Unit / Chiller 1 × separate operating/control panel Connection/connecting cables as shown in the pictures Temperature control/connecting hoses as shown in the pictures Connecting fittings as shown in the pictures Several Huber accessories as shown in the pictures 3 × accessory boxes with contents as shown Additional accessories as shown in the pictures Wooden transport crate Availability: by arrangement. Scope of delivery as shown. Subject to change, errors and prior sale.

Condition: used, Year of construction: 2025, New demonstration machine! Price on request! The CONTROL has always defined its own class – the premium class for vertical panel saws. But even this leading position doesn't stand still. We have developed the CONTROL into the premium class's vertical cutting center, with increased automation of the sawing process and additional equipment options. Above all, the 12" touchscreen computer and the new machine software ensure improved ease of operation in every detail. Saw frame: • Machine components manufactured to a precision of 1/100 mm • Solid, self-supporting, firmly welded, and torsion-resistant saw frame • Full-surface support table made of birch plywood with integrated small parts support • Auxiliary fence profile with its own measuring tape and 3 auxiliary stops for repeat cuts • Automatic detection of the center support • Automatic roller locking during the sawing process Saw beam: • Stable, durable saw beam steel construction • Automatic saw beam locking with cutting interface detection Saw unit: • Backlash-free, smooth-running guides • Robust mounting of the motor carriage ensures high cutting accuracy • Powerful, high-torque 5.5 kW motor (7.5 HP) • More comfort thanks to largely automated operation • Laser-assisted display of the horizontal cut • Automatic motor carriage clamping • Automatic lowering and pivoting of the saw motor • Pneumatic clutch for easy switching to manual operation • SUPERSILENT sound insulation to reduce saw blade noise • Electromagnetic motor brake Control: • 12" touchscreen computer with optimal user guidance • Multilingual user guidance • Tool database guarantees high flexibility and absolute repeatability • Fully automatic sawing process • Infinitely variable feed speeds 10-25 m/min • Selectable sawing cycle • Panel end detection • Constant return speed • Operating hour counter • Network connection • UPS 24VDC for touch PC (uninterruptible power supply) Dimension setting: • Digital measuring system DMS.x (horizontal axis for vertical cuts) • Electronic positioning system EPS.y including ABO (vertical axis for horizontal cuts) Mounting: • Wall or free-standing mounting possible Saw blade: 300 mm, scoring saw, 60 teeth Cutting range: L: 5300 x Hvert: 2240 / Hhor: 2100 x T: 80 mm, consisting of: 1.00 Cutting interface distance vertical 1000 mm 1.00 Language documentation DE 1.00 Saw motor 1-phase, 400V, 50Hz, EVO/CON 1.00 Feed speed 10-25 m/min 1.00 Scoring saw unit VSA (scoring saw infinitely adjustable) 4.00 Free-standing support, complete 1.00 Small parts support, aluminum, complete (2-part) 1.00 STRIEBIG ExpertCut CON consisting of: - Electronic positioning system EPS-X - Automatic saw beam positioning ASP - User guidance with STRIEBIG ExpertCut software license for 1 office workstation (network license) - Label printer - Network connection - Operating manual - Paper holder 1.00 UPS 24VDC for touch PC (uninterruptible power supply) 1.00 Block parts, initial license 1.00 Service: data import / label layout (remote) 1.00 Basic training STRIEBIG cutting optimization (online training) Hnsdpfx Ahszx E T Do Set Storage location: Rieth

Condition: used, functionality: fully functional, Agilent 1100 Series G1159A 6 Position Selection Valve. The 1100 Series Model G1159A 6 Position Selection Valve provides the user comprehensive solutions for more flexibility through solvent selection and column selection. It offers new automation capabilities for sample preparation as well as higher sample throughput with alternating column regeneration. It is fully integrated in the CAN environment (control area network) of the Agilent 1100 HPLC system and can be controlled by the Agilent ChemStation Software. Specifications: Weight 1.9 Kg Hedpsuavn Tsfx Ah Sent Dimensions (height x width x depth) 92 x 84 x 200 mm Power supply 24 Volts DC (1.7 amps) Ambient operating temperature 4 to 55°C Humidity < 95%, non-condensing Good working condition. Please check out our other listings as well.

Condition: used, mileage: 47,830 km, power: 206 kW (280.08 HP), first registration: 08/2003, fuel type: diesel, overall weight: 14,500 kg, axle configuration: 2 axles, brakes: retarder, color: red, gearing type: automatic, emission class: euro3, total length: 10,000 mm, total width: 2,350 mm, total height: 3,300 mm, Year of construction: 2003, Equipment: ABS, air conditioning, compressor, MAN LE 14.280 with METZ DLK 23-12 PLC 3.2 L32 aerial ladder, in immediately operational condition. ---- First registration: 05.08.2003 Mileage: 47,826 km Operating hours of the ladder superstructure: 1,608 hours Operating hours of the vehicle: 2,150 hours Equipment of the base vehicle: * Suspension type: leaf spring/leaf spring * Wheelbase: 4500 mm * Permissible gross vehicle weight: 14.5 t * Automatic transmission ZF 5 HP 590 with retarder Hsdpfxszw R Sij Ah Sont * Fuel tank: 125 l, right side * Adjustable steering wheel * Axle ratio i = 5.86 * Differential lock in rear axle * Medium-length cab * Driver's comfort seat with lumbar support - manufacturer: GRAMMER * Passenger seat bench - manufacturer: GRAMMER * Air conditioning R134A * Exhaust pipe with tailpipe on the left * Auxiliary starter system * Anti-lock braking system (ABS) * Traction control system * Disc brake for front axle * Armrests on both doors * Additional long-range and fog lights * Hour meter * Cruise control * Stabilizers for front and rear axles * Headrests for driver and passenger * Cab rear wall with 3 windows * Heated and electrically adjustable exterior mirrors * Wide-angle mirror on the right, heated * Curb mirror on the right, heated and electrically adjustable * Electric windows on the left and right * 4-wheel parking brake (also on the front axle) * Tire chains on the rear axle * Winter tires 10R22.5 Equipment of the aerial ladder superstructure: * Superstructure: Metz aerial ladder DLK 23-12 PLCIII with rescue platform (rescue height approx. 30.75m). Max. outreach angle: 75 degrees, max. platform load capacity: 270 kg, nominal rescue height: 23 m, nominal outreach: 12 m, outriggers: horizontal-vertical, variable outrigger width between 2,400 mm and 4,500 mm * Rotating beacon lights at the front and rear * Front and rear flashing lights * Air horn * Stretcher storage for accommodating a DIN stretcher, including conversion for accommodating a rescue basket stretcher, load capacity up to 150 kg * Permanently installed 230V power supply to the rescue platform, 2 Schuko sockets in the rescue platform * Permanently installed water supply line in the upper part of the ladder with shut-off valve and B-Storz couplings * 3 anchor points in the rescue platform for securing the crew * Load eye on the lower ladder, loadable up to 4,000 kg * Load eye on the basket segment (between ladder tip and rescue platform) for attaching a lowering device, 270 kg/400 kg payload * LED ambient lighting on the undercarriage * XXL platform on the turntable for accommodating a DIN generator, ventilation unit, traffic cones, etc. * 2 adjustable spotlights at the end of the lower ladder, operable from the main control panel * 2 spotlights on the basket * Permanently installed battery charger Waeco PerfectCharge IU154A * Complete service booklet available, all maintenance performed annually Upon request and for an additional charge, a new 20-year inspection can be carried out, including hose replacement and inspection! ----Immediately operational vehicle in well-maintained condition, both inside and out! Non-smoking vehicle! Your contact person for this vehicle: ---- Daniel Seidler Tel: Mobile: also WhatsApp Email: Subject to changes, prior sale and errors!

Condition: used, Year of construction: 1989, operating hours: 2,500 h, functionality: fully functional, machine/vehicle number: 5399 195, type of input current: three-phase, total length: 6,830 mm, total height: 1,490 mm, total width: 1,400 mm, feed length X-axis: 80 mm, feed length Y-axis: 20 mm, feed length Z-axis: 80 mm, input voltage: 400 V, overall weight: 2,100 kg, compressed air connection: 60 bar, air demand: 60 m³/h, input current: 63 A, year of last overhaul: 2020, sheet thickness aluminum (max.): 40 mm, air pressure: 60 bar, power: 6 kW (8.16 HP), product height (max.): 100 mm, product height (min.): 70 mm, product length (max.): 135 mm, product length (min.): 110 mm, SL80 Bradman Machine – Used & Fully Functional SL80 Bradman machine for sale. The machine is used but in good working condition and is fully functional. It has been well maintained and is ready for use. Hnjdozx Ehzepfx Ah Sst Selling due to no longer being required. Buyer is welcome to inspect the machine before purchase. Please get in touch for more information or additional photos.

Condition: used, Year of construction: 2018, Overview This complete can filling line was manufactured by COMAC and is designed for the filling of carbonated beer in aluminium cans. The line has a nominal output of 5,500 cans/hour for 44 cl cans and 6,000 cans/hour for 33 cl cans. The core machine is a COMAC ISO 14-2 filling and seaming monoblock with 14 electro-pneumatic isobaric filling valves and 2 seaming heads. The filling monoblock includes CO₂ flushing before filling, product tank pressure control, “no can – no fill” function, automatic height adjustment for different can sizes and CIP dummy cans suitable for acid and caustic cleaning up to 80°C. The self-adhesive labeller handles a maximum label length of 210 mm and a maximum label height of 80 / 160 mm at up to 6,500 cans/hour. The dry rinsing system uses approx. 0.25 Nl of ionized air per can, with a treatment time of approx. 3 seconds. Technical data - Line type: Complete can filling line - Manufacturer: COMAC - Year of manufacture: 2018 - Product: Carbonated beer - Nominal output: 6,000 cans/hour (33 cl); 5,500 cans/hour (44 cl) - Filling temperature: 2–4°C - CO₂ content: max. 5.5 g/L - Container type: Two-piece cans with SOT - Can formats: 330 ml and 440 ml - Can diameter: 66 mm - Can end: 202 - Product pressure: 3–4 bar - Water pressure: 3–4 bar - Air pressure: 6 bar - CO₂ pressure: 6–8 bar - Electrical supply: 3x400 V + N + T, 50/60 Hz - Auxiliary voltage: 24 V Scope of Delivery - Can Depalletizer | COMAC | For pallet size 1,120 x 1,300 mm; incl. empty can buffer table and platform | 2018 - Dual Channel Can Rinser | COMAC | Ionized Air Rinser | HEPA filtration, ionized air cleaning, 2-channel design | 2018 - Self-Adhesive Labeller | COMAC | Wrap-around labelling for empty cans; 6-plate carousel | 2018 - Filling / Seaming Monoblock | COMAC | ISO 14-2 | 14 isobaric filling valves / 2 seaming heads | 2019 - Double Shower | COMAC | Washing device after level control | 2018 Hjdpfxozktw Uo Ah Ssnt - Beer Pump | COMAC | Centrifugal beer pump with frequency converter and pressure control | 2018 - Level / Lid Inspection | FT System | HS600-ST+CL003-RX+CT001-SE+ZT | X-ray level control / inspection system | 2019 - Can Twister 1 | COMAC | 180° can inversion before coding | 2018 - Can Dryer | BRB Globus | MEGA ADE 611 CW | 2019 - Ink Jet Coder | COMAC | Continuous inkjet coder, up to 162.5 m/min | 2018 - Can Twister 2 | COMAC | Return cans to upright position | 2018 - Carton closing system | SOCO System | T-10 | 2012 - Can / Case Conveyor System | COMAC | Conveyor system according to layout | 2018 - Conveyor Canopy | COMAC | Stainless steel canopy above empty can conveyors | 2018 - Change Parts | COMAC | – | Format parts for 33 cl cans and 44 cl cans incl. spouts, twisters and labeller parts | 2018 - Technical Documentation | COMAC | Documentation in English, paper copy and CD-ROM | 2018 Condition Used line – built in 2018, currently still installed. The line can be viewed on request. Availability Immediately available. Location: United Kingdom.