Used Artinox Lamella Clarifier for sale (183)

Condition: ready for operation (used), Two Artinox inclined clarifier/lamella clarifier systems made of stainless steel are offered for the continuous mechanical separation of dirt particles, sludge, or sediments from water or process liquids. 1) Artinox inclined clarifier/lamella clarifier, pipe connection: Ø 108mm, additional connection: Ø 168mm, main module dimensions: approx. 2400mm/1350mm/2360mm, hopper width bottom/top/center: approx. 1323mm/1896mm/1546mm, inclination: approx. 1.1°, function: solid-liquid separation by sedimentation, application: process water, wastewater, wash water, liquids containing settleable solids, separation principle: sedimentation with lamella packs/inclined plates, flow direction: horizontal, lamella packs: available, sedimentation hopper: available, equipped with multiple basin modules, lamella clarifier sections, sludge hopper, upper pipe distributor, connection nozzles and flanges, lifting lugs, frame, maintenance access. 2) Artinox inclined clarifier/lamella clarifier, smaller module dimensions: approx. 2300mm/1250mm/1371mm, hopper height/inclined bottom section: approx. 1050mm, inner/lower hopper dimension: approx. 775mm, lamella/sheet spacing: approx. 293mm, function: separation of settleable solids from liquids, design: rectangular clarification tank with hopper bottom, flow path: via inlet, clarification zone, overflow edge, sludge hopper: available, separate pre-collection tank: available on the side, discharge pipe/flange connection: available, maintenance ladder: available, wooden cover: available, equipped with main clarification tank, hopper bottom, side-mounted attachment tank, pipe connection, flange, maintenance ladder, upper cover. Inspection possible by appointment. Bsdpfxozhb Hfs Abtjll

Condition: used, Plant: lamella separator, lamella clarifier, lamella separator Condition: used, up to 120 m³/h depending on medium Design: robust, powerful design Material: VA on conatin frame, 30 ' container, scraper plates: in PP dimensions: LXBXH 7580X2435X3000 mm Weight: approx. 8000 kg Principle: The dirty water is fed to the inlet of the lamella separator and flows downwards in it. Due to the arrangement of the lamella plates in the lamella separator, the dirty water is diverted below the lamellae and flows upwards through the lamellae. Thus, the solids sink to the bottom of the lamellas. The purified water is transported to the outlet. The solids on the lamellas gradually slide down along the lamella plates. This is where the sludge funnel is located. Scraper: Optionally, we offer the lamella separator with a scraper, which keeps the sludge flowable. Blodpfx Ajppyhtjbtol Application: Separation of solids and liquids by sedimentation. Lamella separators are often used as a preliminary stage before filter presses or decanters for thickening. By pre-thickening a thin sludge, the filter press can be sized smaller in terms of filter area. The plant is in good condition and is available for rent or purchase. An inspection at our plant is possible by arrangement. We also offer new lamella separators with a delivery time of approx. 8 to 10 weeks !

Condition: like new (used), Year of construction: 2019, operating hours: 300 h, functionality: fully functional, overall weight: 2,500 kg, rotational speed (min.): 4,500 rpm, screw diameter: 305 mm, year of last overhaul: 2026, temperature: 80 °C, empty load weight: 2,500 kg, power: 22 kW (29.91 HP), Equipment: documentation/manual, rotational speed infinitely variable, Complete Technical Data (GEA OCE 305-01-32)Technical ParameterSpecification and ValuesManufacturer & ModelGEA Westfalia Separator Group GmbH – OCE 305 SeriesEquipment TypeHigh-performance 2-phase decanter centrifuge (Solid-Liquid)Bowl Inner Diameter305 mmBowl DesignFlat-cone design with an extended length (Extended L/D ratio)Maximum Hydraulic CapacityUp to 5 m³/h (varies depending on solid concentration)Maximum Solids Density 2.6 kg/dm³Drive Type2-Gear Drive (System with 2 independent motors, no magnetic brake)Differential Speed ControlAutomatic via dedicated Variable Frequency Drives (VFD)Overall DimensionsLength: 3000 mm | Width: 1000 mm | Height: 1150 mmTotal Weight (Complete Skid)Approx. 2500 kgLubrication SystemAutomatic centralized grease lubrication for main bearingsConstruction MaterialsHigh-grade duplex stainless steel (all product-contact areas)Scroll Wear ProtectionSintered tungsten carbide tiles welded onto the flight edgesII. Liquid Discharge Under Pressure SystemUnlike standard models with gravity discharge (where the liquid falls freely into acollection tank), your model retains the clarified liquid phase inside a hydro-hermetic tripetal Pump (Paring Disk): The separated liquid flows toward the cylindrical end of the bowl, entering a special chamber where a stationary disk with spiral internal channels (a reverse turbine) is etic-to-Pressure Energy Conversion: The kinetic energy of the rapidly rotating liquid is instantly transformed into hydrostatic pressure when it hits the channels of the stationary cess Advantages: The liquid leaves the decanter directly under pressure (without requiring an external transfer pump). This prevents product foaming (highly critical for oils, chemical products, or food-grade applications) and eliminates contact with atmospheric oxygen Electrical cabinet with frequency inverters ant PLC (Siemens ) with acces code for modify the parameters , including factory documentation Blsdpfjzgq Szjx Abtol

Year of construction: 2014, condition: excellent (used), functionality: fully functional, We offer for sale a Bonded Panel Technology LTD (Duemas) Lamella Cutting System for mineral wool boards, complete with extraction unit, manufactured in 2014 and in very good technical condition. Bedeyk Dmnspfx Abtsll This equipment is engineered for precise cutting of mineral wool boards into lamellas with adjustable thicknesses from 40 mm to 200 mm, making it ideal for sandwich panel and insulation material producers. The system comprises: - Lamella saw with 35 Ø550 mm blades (15 new blades in original packaging) - Two 3-meter gravity conveyors - Additional main shaft (2 shafts in total) - Complete set of spacers and top boards for 40, 50, 60, 80, 100, 120, 150, and 200 mm - Complete dust extraction system with 15 kW Auto Shaker filter - Full ductwork and connection components Main technical data: - Maximum slab width: 1010 mm - Maximum slab thickness: 200 mm - Main motor: 15 kW - Power supply: 415V, three-phase - Approx. 3,000 operating hours (2014–2019) This equipment has been well maintained and is in very good working condition. Immediate availability.

Condition: excellent (used), Year of construction: 2024, operating hours: 50 h, Lamella Production Machine The automatic acoustic panel stapler is equipped with an advanced three-axis NC control system, providing exceptional precision and flexibility in the manufacturing process. Below are the detailed advantages of each axis: 1. X-Axis: Precise Stapler Positioning Along the Horizontal Axis - The X-axis ensures accurate horizontal positioning of the staplers along the panel. This guarantees that staples are precisely applied at designated points, ensuring consistent stitching quality across the entire length of the panel, regardless of its size. 2. Y-Axis: Vertical Movement - The Y-axis allows vertical movement of the stapler, enabling stapling at various locations on the panel, regardless of its dimensions or shape. This enables the stapler to work with non-standard sized panels while maintaining full accuracy. 3. Z-Axis: Depth and Stapling Force Control - The Z-axis controls the depth and force with which the staples are driven into the panel. This allows the process to be precisely adjusted according to the thickness and hardness of the acoustic panel material. As a result, staples are embedded with optimal strength, ensuring the durability and aesthetics of the finished product while minimizing the risk of material damage. ### Automatic Changeover Automatic changeover is a key feature that significantly enhances production efficiency. With this function: - Changeover of the X, Y, and Z axes is fully automatic. ### Production Process Optimization Integration with production management systems such as MES (Manufacturing Execution System) and ERP (Enterprise Resource Planning) enables: 1. Full Control Over the Manufacturing Process: - Thanks to MES and ERP integration, every stage of production can be fully monitored and managed. 2. Optimization of Media and Material Consumption: 3. Optimization of Production Plans: ### Significant Relief for Operators Bjdoy Sw I Nspfx Abtsll Automation of the acoustic panel stapling process directly reduces manual workload: - Elimination of manual control requirements - Increased work efficiency ### Capability to Develop Algorithms for Media Demand Analysis Thanks to advanced integration with manufacturing management systems, the stapler allows for the creation of sophisticated algorithms to analyze production media demand: 1. Media Demand Analysis: 2. Adapting Production to Variable Conditions: ### OEE (Overall Equipment Effectiveness) Analysis The stapler also facilitates advanced OEE analysis, a key performance indicator in production operations: 1. Comprehensive Production Monitoring: 2. Automatic OEE Calculation: - The MES system automatically calculates the OEE value based on collected data, allowing immediate assessment of the stapler’s operational efficiency. This tool enables rapid identification of areas requiring optimization, such as downtime reduction, product quality improvement, or machine performance enhancement. 3. Early Detection of Problematic Areas: 4. Optimization of Production Plans: ### TPM (Total Productive Maintenance) and Automated Condition Monitoring The stapler also supports the implementation of TPM philosophy, focusing on maximizing machine efficiency and reliability...

Condition: used, Year of construction: 1976, Drum speed: 4500/min, drum diameter: 650mm, permissible density of centrifuged material, heavy liquid: 1,1kg/dm³, solids: 1,3kg/dm³, control panel: Siemens SIMATIC HMI. Maintenance was carried out every two years by a specialist company, new control system installed two years ago, very good condition, no maintenance backlog, with documentation. An on-site inspection is possible. Bjdpozun S Ijfx Abtsll

Condition: refurbished (used), Year of construction: 1973, functionality: fully functional, rotational speed (min.): 4,800 rpm, Separator WESTFALIA type SB60-06-076 for beer, fruit juices, wine, vegetable juices, tea, coffee, for citrus and tropical fruits for pectin capacity: 300-13.000l per hour with 4,800 rpm Dimensions and weight: Blsdpfxotqf Dbj Abtel Height: 2500 mm Length: 2000 mm Width: 1800 mm Weight: 2350 kg Technical Data: Manufacturer: Westfalia Type: SB60-06-076 Year of construction: 1973 Serial number: 1668 021 Ø dl. 568 mm Drum speed: 4800 rpm Permissible density of the centrifuged material: Heavy liquid: 1.0 kg/ dm3 Solids: 1.45 kg/ dm Test books, tools, drawings available!

Condition: good (used), Hermetic hydro clarifier, complete, tool set, 30 kW motor power, with documentation and overhauled. Price: 35,000 euros. Bodpsy Rtlzjfx Abtsll

Condition: used, mileage: 5,13,267 km, power: 228 kW (309.99 HP), first registration: 08/2006, fuel type: diesel, overall weight: 18,000 kg, axle configuration: 2 axles, color: red, gearing type: mechanical, emission class: euro3, loading space length: 4,200 mm, loading space width: 2,450 mm, loading space height: 600 mm, Year of construction: 2006, Equipment: ABS, all wheel drive, crane, Stock No. 5883 MAN TGA 18.310 with front-mounted HIAB crane, type 111 BS-3 HIDUO, with remote control / Meiller steel 3-way tipper / 4x4 / AP axles 3rd and 7th synchronizer rings are worn!!! (transmission) ----* Manufacturer: MAN * Type: TGA 18.310 4x4 BL * First registration: 08/2006 Blodpfezyfk Sjx Abtjl * Mileage: approx. 513,267 km * Transmission: mechanically shifted, 8-speed split * Gross vehicle weight: 18,000 kg * Unladen weight according to vehicle registration document: 11,350 kg * Payload: 6,650 kg * Axles: 4x4 all-wheel drive / AP axles * Wheelbase: approx. 4.00 m * Suspension: front leaf suspension, rear air suspension * Tires: 1st axle 385/65 R 22.5, 2nd axle 315/80 R 22.5 approx. 50% tread * Cab: short cab / 2 seats * Horsepower: 310 hp / Euro 3 / L package * ABS * Color: Chassis black, cab and tipper body red * Tipper dimensions (internal): Tipper internal approx. 4.20 m long x 2.45 m wide x 0.60 m high * Front-mounted HIAB crane, type 111 BS-3 HIDUO, with remote control, year of manufacture 2006 * 3 hydraulic outriggers * Maximum reach at 9.50 m = 1,040 kg * Short reach at 3.90 m = 2,660 kg * 5th and 6th control circuits for grab * Two-shell grab * Hydraulic supports * Ground control on the left * Load hook * Meiller steel 3-way tipper * Trailer coupling, 40 mm hitch, with air, light and hydraulic connections for trailer operation * Approx. 225-liter steel diesel tank on the right * 2 x front toolboxes on the left * Work lights * Rotating beacon * Chrome roof rack with spotlights * Roof fan * Cab rear wall with window * Sun visor * Heated driver's seat * Roof hatch * Electric windows and mirrors * Mirror heating * Cool box * Radio * Cruise control * Engine brake * Differential lock * Exhaust pipe on the right, raised behind the cab German vehicle!! German documents!! Note regarding possible errors in the advertisement: Despite careful preparation of the advertisement, individual errors may have crept into the text or the details. We assume no liability for errors, changes or intermediate sales. All information is without guarantee. Please contact us to verify details or clarify any further questions.

Condition: used, mileage: 5,13,267 km, power: 228 kW (309.99 HP), first registration: 08/2006, fuel type: diesel, overall weight: 18,000 kg, axle configuration: 2 axles, color: red, gearing type: mechanical, emission class: euro3, loading space length: 4,200 mm, loading space width: 2,450 mm, loading space height: 600 mm, Year of construction: 2006, Equipment: ABS, all wheel drive, crane, Stock No. 5883 MAN TGA 18.310 with front-mounted HIAB Type 111 BS-3 HIDUO crane with remote control / Meiller steel 3-way tipper body / 4x4 / AP axles 3rd and 7th synchronizer rings are worn!!! (Transmission) ----* Manufacturer: MAN * Type: TGA 18.310 4x4 BL * First registration: 08/2006 * Mileage: approx. 513,267 km * Transmission: mechanically shifted 8-speed split gearbox * Gross vehicle weight: 18,000 kg * Unladen weight according to vehicle registration: 11,350 kg * Payload: 6,650 kg Bljdezyflcopfx Abtol * Axles: 4x4 all-wheel drive / AP axles * Wheelbase: approx. 4.00m * Suspension: front leaf spring, rear air suspension * Tires: 1st axle 385/65 R 22.5, 2nd axle 315/80 R 22.5 approx. 50% tread * Cab: Short cab / 2 seats * Horsepower: 310 hp / Euro 3 / L package * ABS * Color: Chassis black, cab and tipper body red * Internal dimensions of tipper body: Tipper body approx. 4.20m long x 2.45m wide x 0.60m high * Front-mounted HIAB Type 111 BS-3 HIDUO crane with remote control, year of manufacture 2006 * 3 hydraulic extensions * Maximum extension at 9.50m = 1,040 kg * Short extension at 3.90m = 2,660 kg * 5th and 6th control circuits for grab * Two-shell grab * Hydraulic supports * Floor control on the left * Load hook * Meiller steel 3-way tipper body * Trailer hitch with 40mm pin and air, light, and hydraulic connections for trailer operation * Approx. 225 liter steel diesel tank on the right * 2 x front toolboxes on the left * Work lights * Rotating beacon * Chrome roof rack with spotlights * Roof horn * Cab rear wall with window * Sun visor * Heated driver's seat * Roof hatch * Electric windows and mirrors * Mirror heating * Cooler box * Radio * Cruise control * Engine brake * Differential lock * Exhaust pipe on the right, raised behind the cab German vehicle!! German documents!! Note regarding possible errors in the advertisement: Despite careful preparation of the advertisement, individual errors may have crept into the text or the details. We assume no liability for errors, changes, or interim sales. All information is without guarantee. Please contact us to verify details or clarify any further questions.

Condition: used, The machine is in good working order and ready for use. It was previously used in a company that specializes in vegetable washing. The machine was used to pre-treat wastewater. Bedpfx Ajzc Ef Asbtell Please check out my other listings.

Condition: repair required (used), Year of construction: 2017, functionality: not functional, AS-07251-Alfa Laval Clarifier Module 10 m3/h ALFA-LAVAL PURE SOX (SWPX 810 SGV-34CGL) CLARIFIER MODULE, 316SS. Capacity min. 10,000 L/H Offering 4 identical units Bsdpfjw Ap I Aex Abtjll INCOMPLETE! Only for spare parts (Machine without bowl) Max. bowl speed 7200 RPM, rated at 10,000 LPH, bowl volume 15 L, sludge capacity 9.4 L, liquid discharged under pressure, solids discharge pump with cyclone tank, 35 kW motor 460/3/60/1728 RPM, Pure SOx scrubber, unitized on a common skid with all valves, piping, control panel, tools, spares, and manual Year of Manufacture 2017

Year of construction: 2013, operating hours: 7,700 h, condition: repair required (used), functionality: limited functionality, machine/vehicle number: 12090, This is a recycling extruder with side feeding for materials (flakes, pellets, etc.). The system is supplied with a control cabinet and a double vacuum system. The pelletizing system is missing at the end of the screw – it is not included in the scope of supply. The cylinder ends at the flange. The extruder is supplied without a screw. The frequency inverter for the main motor was replaced with a new unit 3 years ago. Installed power approx.: 474 kW Cooling water requirement approx.: 190 l/min Fresh water consumption approx.: 110 l/h Feeding system: • Diameter of the feeding screw: 200 mm • Drive for the feeding screw: 45 kW, frequency-controlled • Hopper capacity net 7 m³/250 ft³, • Gear motor 3 × 3 kW • 2 sight glasses in the hopper • 2 level indicators Extruder: • Diameter of the extruder screw: 145 mm • L/D ratio: 24 • Heating power: 50 kW • Extruder drive unit 280 kW Vacuum 1: • Screw length: 16 L/D • Heating power: 40 kW • Vacuum pump power: 11 kW • Vacuum capacity: 225 m³/h • Vacuum pressure: 33 mbar Vacuum 2: • Screw length: 16 L/D • Heating power: 40 kW • Vacuum pump power: 7.5 kW • Vacuum capacity: 190 m³/h • Vacuum pressure: 33 mbar Cylinder: • Cylinder: Bimetal extruder cylinder, • Reinforcement layer 1.8–2.0 mm thick, • Hardness 63–65 HRC Installation conditions: • Voltage: 3 × 400 Volts • Permissible fluctuation max.: +5 % – 5 % • Frequency: 50 Hz Permissible fluctuation max.: +4 % – 4 % • Protective measure: Multiple grounding • Ambient temperature: min. 15 °C, max. 35 °C • Humidity max.: 90 % • Altitude of the installation site: 0 – 1000 m Blodpfoznz Ezox Abtel The machine was in operation at an R&D center in Israel. Since the company now operates a production facility in Europe, the R&D center is being closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production facility in Europe. The details for optimal transport need to be clarified. The machine price is without packaging.

Condition: like new (used), HERMETIC CLARIFIER. POWER: 7.5 kW. COMPLETE TOOL SET. INSPECTED. DOCUMENTATION AVAILABLE. PRICE: 25,000 EUROS PLUS VAT. Blodpfsy S Smyox Abtjl

Year of construction: 2013, operating hours: 3,500 h, condition: used, functionality: fully functional, machine/vehicle number: 12400, TSM/tsi oscillating sieve machines are used for the classification, screening, and dust removal of bulk materials from almost all industrial sectors, such as stones and soils, chemicals, mining, pharmaceuticals, feed, and food. The machine for sale has a diameter of 1200 mm and is equipped with 3 sieve decks with mesh sizes of 3 mm, 1.4 mm, and 0.463 mm. In addition, spare sieves with the following dimensions are included: • 16 mm x 1 piece • 15 mm x 1 piece • 0.5 mm x 1 piece • 0.16 mm x 1 piece • 0.9 mm x 1 piece Bedpfxjzmzbme Abtjll • 0.86 mm x 1 piece The drive has a power of 1.5 kW, 400 VAC, 50 Hz, 1450 RPM. The machine was in operation at an R&D center in Israel. As the company now operates a production facility in Europe, the R&D center will be closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production facility in Europe. The details for optimal transport need to be clarified. The machine price does not include packaging on a pallet.

Condition: used, Year of construction: 2013, operating hours: 3,500 h, machine/vehicle number: 13620, rotor diameter: 395 mm, rotor width: 1,300 mm, input voltage: 400 V, number of blades: 60, rotational speed (max.): 129 rpm, power: 55 kW (74.78 HP), We sell the shredder as a set including a pit conveyor, shredder, and discharge conveyor. The Vecoplan universal shredder – VAZ – can be used for a variety of materials – waste shredding, plastic shredding, wood shredding, etc. The machine, with a power output of 55 kW, is equipped with 60 cutting heads measuring 60x60 mm. A turbo coupling facilitates the start-up process, allowing the machine to be started even with a full hopper. The hopper is made of stainless steel, and the extraction hood is made of galvanized sheet metal. The machine, including the control panel, is offered for sale. The hopper and extraction hood are included. Bljdezmzduepfx Abtjl Spare parts are included in the price of the shredder. The machine was in operation at an R&D center in Israel. Now that the company is operating a production facility in Europe, the R&D center will be closed. The machines will be transported to Europe at the owner's expense and can be delivered ex-works at a port or at the production facility in Europe. The details for optimal transport need to be clarified. The machine price does not include packaging for pallet transport.

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, Cabinet length: from 250 to 2500 mm Cabinet depth: from 250 to 700 mm Cabinet height: from 150 to 1400 mm Working height: 300 mm Pressing pressure (fixed): max. 15 kN Positioning speed (fixed): 25 mm/s Bsdpfx Abozphrkjtell Transport interface: no Control: via contactors/protection devices Weight: approx. 2.2 t

Condition: excellent (used), Year of construction: 2013, operating hours: 2,500 h, functionality: fully functional, machine/vehicle number: R1203433 Pos 1000, overall weight: 365 kg, rotor diameter: 400 mm, rotor width: 320 mm, opening width: 340 mm, input voltage: 400 V, power: 22 kW (29.91 HP), A very robust hammer mill from Alpine with grate bars for crushing soft to medium-hard materials. The mill is supplied with an inlet hopper and a device for pneumatic extraction. A control panel is not included. Bledezl E N Ejpfx Abtsl Machine data: 365 kg; 2800 RPM, 22 kW Rotor 400x320 mm, cast iron rotor, inlet 340x150 mm, Design with grate bars 4 rows of hammers, 5 hammers per row The machine was in operation at an R&D center in Israel. As the company now operates a production facility in the Netherlands, the R&D center will be closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production facility in the Netherlands. The details for optimal transport need to be clarified. The machine price does not include packaging on a pallet.

Condition: excellent (used), Year of construction: 2021, operating hours: 3,500 h, functionality: fully functional, machine/vehicle number: 2021-1504-QN, High-end metal separator for inspecting bulk materials in free fall Material: stainless steel 304 Surface: sandblasted Sensing tube material: PE, anti-static, food grade Rejector: single flap type RH Protection rating: IP66 Electronics assembly: detached Control electronics cable length: 3 m Nominal width: 150 mm Orientation: vertical, top to bottom Power supply: 100-240VAC 50-60Hz LNPE - Without power cable Pressurized air supply: 6-10 bar Expected sensitivity: FE: 0.4 mm NE / Al: approx. 0.4 to 0.56 mm Stainless steel: approx. 0.4 to 0.72 mm Electronics outside ATEX Zone Inside: Zone 20 within metal separator (pipe) = II 1 D Ex h IIIC T135°C Da Bedpfozvwlmex Abtell Outside: Zone 22 surrounding metal separator = II 3 D Ex tc IIIC T135°C Dc IP65 QUICKTRON 07 RH metal separators are used for inspecting powders and granules in free-fall lines. They are available in nominal widths up to 300 mm and can therefore cover all application areas, from the laboratory to truck loading. Their hygienic design and easy cleaning prevent cross-contamination between product batches. Depending on the requirements, they can increase process safety or fulfill the task of outgoing goods inspection. Mesutronic metal detectors use state-of-the-art technology to protect your production, your reputation, and your customers from damage caused by metallic foreign objects. Digital signal processing, combined with innovative evaluation methods, comprehensive self-monitoring, and ease of operation, ensure the optimal function of the system and the successful completion of all types of audits. The devices are complemented by an extensive range of accessories and variants, from multi-frequency technologies to test bodies and material certificates. The machine was in operation at an R&D center in Israel. As the company now operates a production facility in Europe, the R&D center will be closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or in the production plant in Europe. The details for optimal transport need to be clarified. The machine price does not include packaging.

Condition: used, Year of construction: 2012, GEA Milk Separator MSE 100-06-177 Bjdpfewayr Tox Abtoll Year of manufacture: 2012 Maximum permissible drum speed: 7200 rpm Maximum permissible feed density: 1.0 kg/dm³ Heavy liquid: 1.0 kg/dm³ Solids: 1.1 kg/dm³ Min./max. feed temperature: 5/100 °C Max. throughput: 30 m³/h

Condition: repair required (used), Year of construction: 2009, functionality: limited functionality, machine/vehicle number: 305484, saw blade diameter: 450 mm, cutting height (max.): 160 mm, feed length X-axis: 2,000 mm, cutting range round steel at 45°: 150 mm, cutting range round steel at 90°: 150 mm, type of input current: three-phase, cutting range square steel at 45°: 140 mm, cutting range square steel at 90°: 140 mm, CNC cold saw from the renowned brand Kaltenbach, model KKS 401 NA 2000. There is a lot of information to provide, so I have posted several pictures with basic details to give you an overview of the saw's capabilities. It is a rare model with a feeder (single piece) of 0-2000mm, as well as repeat cutting of 2000-9999mm. Automatic zeroing before cutting. CNC saw head with automatic rotation of +/-60 degrees, 2 types of lubrication, emulsion, and direct spray. Option to direct the cut piece to an ejector for small pieces, as well as a chain ejector with a function for lowering longer and heavier pieces. I haven't included this in the pictures as it is not installed, but the saw also comes with a set of protective guards with safety barriers and a large number of spare parts. The complete documentation is original and is linked to the machine's serial number, making installation easy and straightforward. Problem explanation: the saw is connected to the electrical power supply, and each individual function (and there are many) is fully operational. The problem arises during automatic operation; the most likely cause is the program parameters themselves (it uses the Windows platform). I haven't been able to find a suitable programmer who can learn on my machine. Possible solution: I contacted the saw manufacturer, and they directed me to their authorized service provider, so I have their contact information, which I can provide to the future buyer. The estimated cost of repair in Serbia is between 3000-5000 EUR. If you are closer to Germany or the Czech Republic, this cost will be significantly lower. So, there are two price categories: if you buy the machine in its current condition, the price is as advertised. If I resolve the problem, the price will be considerably higher. The advertised price includes professional dismantling and loading onto a truck (a rather important, and not inexpensive, item). Transportation is at the buyer's expense. I hope I have clarified the current condition of the machine. Due to a change in business activities, the saw is surplus to production. Happy shopping! Bljdpfx Abjyk Inpstjl

Condition: excellent (used), Year of construction: 2016, operating hours: 3,000 h, functionality: fully functional, machine/vehicle number: 565697, type of input current: three-phase, input voltage: 400 V, belt width: 600 mm, conveyor belt width: 600 mm, The Wagner non-ferrous metal separator (NE separator), model 0429 from Wagner Magnete, is one of the manufacturer’s high-performance eddy current separators. Working width: 600 mm. • Throughput: depends on the material and grain size. • Rotor speed: up to 3,000 revolutions per minute. • Belt speed: 0.5 to 2.0 m/s. Bsdezl Rfxspfx Abtell • Weight: 1.2 tons. • Rotor system: Eccentrically mounted with a high pole-changing frequency. • Rotor drive: 4 kW; belt drive: 1.5 kW. The machine and the associated control panel are included in the delivery. The machine was in operation at an R&D center in Israel. As the company now operates a production facility in Europe, the R&D center will be closed. The machines will be transported to Europe at the owner’s expense and can be delivered EXW at a port or in the production facility. The details for optimal transport need to be clarified. The machine price is quoted without packaging on a pallet.

Condition: excellent (used), Year of construction: 2019, operating hours: 2,000 h, functionality: fully functional, machine/vehicle number: R1253899, overall weight: 2,200 kg, rotor diameter: 500 mm, rotor width: 840 mm, type of input current: three-phase, A very robust cutting mill Machine data: Bodpfx Ajzl E Stsbtoll 2200 kg; 1478/562 RPM, 45 kW Rotor 500x840 mm, 5 rows of rotor knives, 4 rows of stator knives Cast iron rotor, inlet 340x150 mm, Sieves with 3-2.5-1 mm 4 rows of hammers with 5 hammers each The delivery scope also includes: Alpine Classifier MZM 160x500, fan 7.5 kW, rotary valve, some piping A control cabinet is not available and must be built by the buyer. The machine was in operation at an R&D center in Israel. As the company now operates a production facility in the Netherlands, the R&D center will be closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production facility in the Netherlands. The details for optimal transport need to be clarified. The machine price is quoted excluding packaging on a pallet.

Year of construction: 2013, operating hours: 3,500 h, condition: used, functionality: fully functional, machine/vehicle number: 12399, TSM/tsi rotary vibrating screens are used for the classification, screening, and dedusting of bulk materials from almost all industrial sectors, such as stones and soils, chemicals, mining, pharmaceuticals, feed, and food. The machine offered for sale has a diameter of 1200 mm and is equipped with 3 screen decks with mesh sizes of 3 mm, 1.4 mm, and 0.463 mm. In addition, spare screens with the following dimensions are included: • 1 mm x 1 piece • 0.5 mm x 2 pieces • 0.17 mm x 1 piece Bjdpfxjzmzbge Abtsll • 1.4 mm x 1 piece • 5 mm x 1 piece • 4 mm x 1 piece • 1.8 mm x 1 piece The drive has a power of 1.5 kW, 400 VAC, 50 Hz, 1450 RPM. The machine was in operation at an R&D center in Israel. Since the company now operates a production facility in Europe, the R&D center is being closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production plant in Europe. The details for optimal transport need to be clarified. The machine price does not include packaging on a pallet.

Year of construction: 2023, operating hours: 1,500 h, condition: excellent (used), functionality: fully functional, Abstracts This is a high-quality system that mixes and homogenizes up to 3 additives in a hot mixer. The control system is included in the scope of supply. First, the material is transported from the production area to a storage silo. From this first silo, the material is fed into the hot mixer, then into the cooler, and finally into a second silo for intermediate storage. After that, there is the option to directly fill the powder onto a big bag filling scale or to compress it into pellets using a pellet press and then fill them. The steel structure is included in the scope of supply. Where necessary, the system is designed according to ATEX standards. In the Documents section, you will find a detailed English and German description of the complete scope of this system. Do not hesitate to call us to discuss and demonstrate the system. A similar system can be inspected in Europe. Blodpfx Abjztc Nfetsl Main machines: • Mixaco hot mixer HM3000 - 400 kW • Mixaco cooling mixer KM9000 - 90 kW • Steel structure • AZO feeding station and gravimetric dosing for 2 solids and 1 liquid • AZO 2 special dosing scales for difficult-to-flow powders or solids • AZO 4 transport line, pressure and vacuum conveying • AZO 2 metrologically verifiable big bag filling stations • AZO control system • Kreyenborg silos ATEX 15 m³ • Kahl pelletizer 37-850 – 132 kW with box cooler and accessories The system was in operation at an R&D center in Israel. As the company now operates a production facility in Europe, the R&D center will be closed. The machines will be transported to Europe at the owner's expense and can be delivered at a port or in the production facility in Europe, EXW. The details for optimal transport need to be clarified. The machine price does not include packaging.