Used Sincotec Sincotec Resonance Testing Machine Power Swing 20 Kn Mot, Large Table for sale (1,03,079)

Condition: used, SincoTec Type: Exciting Mot Resonance test bench POWER SWINGLY 20 kN The POWER SWINGLY BigTable resonance test bench is designed as a dual-mass vibrator. It consists of a vibration head, which is excited via an asynchronous motor with frequency control and an eccentric motor. The vibration head is located in the upper part of the machine and generates the dynamic amplitude. The vibration head is supported on the upper traverse via pre-tensioned coil springs and is guided centrally. The center load drive is located in the lower part of the machine and applies the static preload with the aid of a geared motor via a spindle drive. Ljdpszii Awsfx Akmoru The test chamber is located above the mounting table and is bounded upwards by the adjustable traverse. The control of the test bench is carried out by the EXCITING MOT control system. The complete control electronics for the control system are housed in an industrial PC cabinet. The control cabinet is made of powder-coated steel sheet and meets protection class IP 50 according to EN 60529. Technical data: General data of the test bench: Overall height of the test bench 1840 to 2240 mm Height of the machine table 1030 mm Width of the test bench 800 mm Depth of the test bench 1500 mm Height of the test chamber max. 600 mm (without force sensor) Free column passage 550 mm Maximum force amplitude 10000 N Maximum total force ±20000 N Maximum stroke ±5 mm Test frequency 30 to 110 Hz Accuracy of the measuring sensors min. class 1 (according to DIN EN 10002-3) Weight of the test bench approx. 1880 kg Max. weight of the clamping device 150 kg General data of the control cabinet: Overall height of the control cabinet 1900 mm Height of the table top 1080 mm Width of the control cabinet 650 mm Depth of the control cabinet 700 mm Weight of the control cabinet 152 kg Color RAI 9006 (white aluminum), table top Midnight Conditions for the installation site: Space requirement 2.5 x 2.5 m Required ceiling height 2.8 m Floor load-bearing capacity 170 N/cm² Voltage supply 400 V / 50 Hz (right-rotating field) Connection plug CEE socket, 5-pole, 16 A Fuse 16 A Connection and environmental conditions Mains conditions: Voltage 400 V three-phase with PE conductor and protective earth, right-rotating field Voltage fluctuations < ± 10% Short-time voltage dips < 20 ms Limits for permanent interference Radio interference level A according to VDE0871 Frequency 50 Hz ± 1% Protective earth Ground resistance < 0.3 Ω Model: POWER SWINGLY MOT Condition: used Scope of supply: (See picture) (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: used, SincoTec Type: POWER SWING 20 kN POWER SWING 20 kN resonance testing system Sincotec Power Swing 20 kN resonance testing system Manufacturer's maintenance performed General information For sale is a used Power Swing 20 kN resonance testing system from Sincotec Test Systems GmbH. The testing system was used in a single-shift operation, and all maintenance work was performed regularly by the manufacturer. Special features: Robust construction for continuous operation Precise resonance testing up to 20 kN Manufacturer's maintenance available Ideal for research, testing, and development applications Technical data – Testing system Feature / Value Overall height of testing system 1215 mm (without clamping device) Width of testing system 2005 mm Depth of testing system 1205 mm Maximum force amplitude 10 kN Maximum total force ±20 kN Accuracy of measuring sensors min. Class 1 (according to DIN EN 10002-3) Technical data – Control cabinet Feature / Value Overall height of control cabinet approx. 1800 mm Height of tabletop 1080 mm Width of control cabinet 650 mm (narrow tabletop) / 1450 mm (wide tabletop) Depth of control cabinet 700 mm (narrow tabletop) / 800 mm (wide tabletop) Weight 152 kg (small tabletop) 187 kg (large tabletop) with (granite plate) 247 kg Conditions for the installation site Feature / Value Space requirement 4.3 × 3.0 m Required ceiling height 2.5 m Floor load-bearing capacity 234 N/cm² Mains conditions Feature / Value Voltage 400 V three-phase with neutral conductor and protective earth Phase sequence Right-rotating field Voltage fluctuations ≤ ±10 % Lrjdpfxjzii A Dj Akmsu Short-time dips < 20 ms Limits for sustained disturbances Radio interference level A according to VDE 0871 Frequency 50 Hz ± 1 % Protective earth / Grounding resistance < 0.3 Ω Connection and protection Feature / Value Voltage supply 400 V / 50 Hz (Right-rotating field) Connection plug CEE socket, 5-pole, 16 A Protection 16 A Weight of testing system approx. 3.6 t Max. weight clamping device 250 kg Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We would be happy to answer any further questions you may have by phone.

Condition: used, SincoTec Type: POWER FLOW 100kN / 2000Nm Sincotec Power Flow 100 kN / 2000 Nm – Servohydraulic testing machine – fully functional Description: For sale is a servohydraulic testing machine, Sincotec Power Flow, from an industrial operation. The system is ideally suited for dynamic and static testing of components and assemblies, e.g. in the automotive, mechanical engineering or research field. Technical highlights: Max. testing force: 100 kN (up to ±150 kN) Max. torque: ±2000 Nm (up to ±4000 Nm) Linear stroke: ±50 mm (max. ±75 mm) Max. swivel angle: ±50° Servohydraulic control Control via Sincotec TestPilot / CoPilot software Includes large hydraulic power unit Lrjdpfx Akjzimb Demeu Dimensions & testing machine Testing table: approx. 1.20 × 1.00 × 1.20 m (H) Overall height of testing machine: approx. 3.30 m Hydraulic power unit (separate) Height: 2085 mm Length: 2714 mm Width: 1820 mm Fully functional before disassembly Power supply / electrical (from nameplates) Individual units / motors 230 V / 50 Hz Leak oil pump: 0.18 kW / 1.5 A 400 V / 50 Hz (three-phase) Crossbeam: 0.25 kW / 0.79 A Total weight: approx. 3000 kg Important note: "The table shown in the photos is not included in the sale." Condition: used Scope of supply: (See picture) (Changes and errors in the technical data are subject to change!) We would be happy to answer any further questions you may have by phone.

Condition: used, SincoTec Type: POWER FLOW BIAXIAL 125/150 kN ±4000 Nm SincoTec POWER FLOW BIAXIAL 125/150 kN – ±4000 Nm Servo-hydraulic testing machine Description: For sale is a servo-hydraulic biaxial testing machine, the SincoTec POWER FLOW BIAXIAL. The machine comes from an industrial application and was fully functional until it was decommissioned. Service and maintenance were carried out professionally. Extensive technical documentation (operating, assembly, and wiring diagrams) is available. The testing machine is suitable for tensile/compression tests, torsion tests, and combined load tests on components and assemblies, e.g., for fatigue, life, and functional tests. Technical main data of the testing machine: Maximum test force (design): up to ±150 kN Typical operating design: 125 kN Max. torque (torsion): ± 4,000 Nm Max. stroke of linear cylinder: ± 75 mm Max. angle of rotation: ± 50° Measurement accuracy: Class 1 (DIN EN 10002-3) Dimensions of the testing machine: Ljdozimcbjpfx Akmsru Overall height: approx. 3,430 mm Width: approx. 1,480 mm Depth: approx. 1,180 mm Max. weight of clamping device: 250 kg Hydraulic power unit (included in the scope of delivery) Drive power: approx. 152 kW Flow rate: approx. 260 l/min Operating pressure: up to 280 bar Hydraulic oil: HLP ISO VG 46 Tank volume: approx. 1,500 liters Dimensions of the power unit: Length approx. 2,714 mm Width approx. 1,820 mm Height approx. 2,085 mm Electrical data: Control cabinet / testing machine 400 V / 50 Hz Connection: CEE 5-pole Fuse: 16 A Hydraulic power unit 400 V / 50 Hz three-phase Fixed connection Fuse: approx. 160 A Scope of delivery Servo-hydraulic testing machine SincoTec POWER FLOW BIAXIAL Hydraulic power unit Control cabinet with industrial PC Measuring and control technology Technical documentation The machine is designed for a maximum of 150 kN. The 125 kN specification refers to the typical operating design. Weight of testing machine: approx. 4.7 t Important note: "The table shown in the photos is not part of the sale." Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data and information are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: used, Zwick Type: BZ2.5/TN1S Zwick table-top testing machine, tensile strength measuring machine Application area: Wide range of applications, from testing plastics and elastomers to testing paper, textiles, foam, and wire, as well as component testing. Load frame: Max. test force FN in tension/compression direction: 2.5 kN Height (h1): approx. 770 mm Width with electronics unit: 320 mm Depth with electronics unit: 414 mm Height of the working area h min ... h max: Travel carriage angle mounted upwards: 227 ... 573 mm Travel carriage angle mounted rotated by 180°: 57 ... 403 mm (each without connecting pin) Connection values: Electrical connection: 115/230 V, 4/2 A, 1-phase/PE/N Ljdjzdry Iepfx Akmoru Power consumption: 0.4 kVA Mains frequency: 50/60 Hz 2.5 kN Condition: used Scope of delivery: (See image) (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by phone.

Condition: used, Zwick / Roell Universal testing machine / Material testing machine Zwick / Roell Z005 5 kN Allround table-top Complete material testing system with testXpert II and extensive accessories For sale is a used universal testing machine from the manufacturer Zwick / Roell. The testing system is suitable for tensile, compression and material tests, as well as for component, plastic, metal and parts testing. Technical data: Manufacturer: Zwick / Roell Type: Z005 / 5 kN Allround table-top Testing system type: S0101 Max. testing force: 5 kN Crosshead speed: 0.0005 – 3,000 mm/min Return speed: max. 3,000 mm/min Testing width: 640 mm Testing height without attachments: approx. 1,400 mm Dimensions of the testing system with stand profiles and machine electronics (W x D x H): approx. 1,244 x 690 x 1,878 mm Weight with typical attachments: approx. 291 kg Power connection: 230 V / 50–60 Hz Connection: 1L / PE / N Equipment: Zwick / Roell Z005 5 kN testing machine Zwick / Roell machine electronics Handheld control unit with emergency stop Zwick / Roell testXpert II testing software PC system with monitor, keyboard and mouse Load cell and measuring components SAIM cross / positioning table Specimen holders and clamping tools Clamping plate Connection and measuring cables Lrjdpsz Iy Tzsfx Akmju Original operating manuals Software / documentation Further extensive accessories as shown in the pictures Application areas: Tensile testing Compression testing Material testing Component testing Plastic and metal testing Parts testing Automotive testing Quality assurance Research and development Scope of delivery: 1 × Zwick / Roell Z005 5 kN Allround table-top Machine electronics and handheld control unit PC workstation with testXpert II Testing and clamping tools Load cell / sensors SAIM positioning table Documentation and accessories as shown in the pictures Condition: Used Optical condition as shown in the pictures Signs of wear and tear due to age and use The table shown in the photos and other items not explicitly mentioned are not part of the sale. Shipping or freight transport is possible. Subject to changes, errors and prior sale. We will be happy to answer any further questions by telephone.

Condition: used, Zwick / Roell Type: Z020 Allround-Line BT1-FR020TN.A50 Zwick / Roell Material Testing Machine, 20 kN, Tensile & Compression Testing, testXpert III For sale is a high-quality Zwick / Roell material testing machine for professional tensile and compression testing of materials and components. The machine is suitable for metals, plastics, rubber, and many other materials and is typically used in laboratories, quality assurance, research, and education. The machine is controlled via a PC with Zwick/Roell testXpert III software (storage medium and documentation available). Technical Data: Nominal testing force: 20 kN Testing direction: Tensile & Compression Power connection: 230 V / 50–60 Hz / 1-phase Power consumption: approx. 2.1 kVA Weight: approx. 150–180 kg Dimensions: approx. 856 × 650 × 1,545–2,114 mm Technical Data (from documents & nameplate) Mechanics / Testing Nominal force: 20 kN Testing direction: Tensile & Compression Max. testing frequency: 0.5 Hz Crosshead: servo-electric Positioning accuracy: < 1 µm Speed range: 0.0005 – 1,000 mm/min Dimensions & Weight Overall height: approx. 1,545 – 2,114 mm (depending on the crosshead position) Overall width: approx. 856 mm Overall depth: approx. 650 mm Working space width: 440 mm Weight: approx. 150 kg (basic unit) approx. 180 kg with typical equipment Electrical Data Power connection: 230 V AC Phases: 1-phase (1PH, N, PE) Mains frequency: 50 / 60 Hz Current consumption: approx. 8–10 A Power consumption: approx. 2.1 kVA Socket: Schuko (CEE 7) Measuring & Control Electronics Internal measurement value acquisition: 500 Hz Data transmission to PC: 10–100 Hz adjustable Interface: RS232 (COM) Protection class for electronics housing: IP32 Important note: “The table shown in the photos is not included in the sale.” Lrjdpfxjzimgto Akmeu Condition: used Scope of supply: (See picture) Zwick / Roell material testing machine (20 kN) Electronics unit PC workstation (monitor, PC condition see pictures) 2 measuring modules (Delock units) Zwick/Roell testXpert III software (storage medium) Original operating and technical documentation Various connection and linking cables (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have by phone.

Condition: used, Zwick   Type: BZ1.0 / TH1S   Zwick table-top testing machine Ledpfxozdryzo Akmjru   Zwick with a maximum force of 1.0 kN.   Crosshead travel: 1150 mm. Testing speed: 0.1 ... 1800 mm/min   Scope of supply: (See images)   (Changes and errors in the technical data are subject to change!)   We would be happy to answer any further questions you may have by phone.

Condition: used, OMAG / AFFRI 903 RSD Hardness Testing Machine Professional, stationary benchtop hardness testing machine from the renowned Italian manufacturer OMAG di AFFRI DAVIDE s.r.l. (Model 903 RSD). Semi-automatic hardness tester for Rockwell, Super-Rockwell, Brinell, and Vickers hardness testing methods according to ASTM and DIN EN ISO. The hardness testers of the RSD series are suitable for all conditions, both in production and in the laboratory. Rockwell and Brinell HBTW hardness values with high accuracy (better than 0.5%) in almost any testing environment. Accurate measurement results are achieved with the very first test. The load is applied by means of a dynamic load cell. A user-friendly interface with real-time statistics, graphics, and large archive storage, as well as conversion to other methods, makes measurement a breeze. For hardness testing on almost all metals: iron, steel, hardened steel, cast iron, brass, aluminum, copper, and metal alloys. The device has been regularly inspected and certified by the DAkkS-accredited laboratory 3-Rath Kalibrier + Prüftechnik (last inspection on April 28, 2025, for the HRC method according to DIN EN ISO 9000ff). Technical data: Manufacturer: OMAG / AFFRI Group (Italy) Model: 903 RSD Serial number: 76599 Ljdpfx Aezni D Eekmoru Testing method: Rockwell (including HRC, which is calibrated) Voltage: 115 – 230 V Weight / test force: 195 Kgf Special feature: Height-adjustable testing head for flexible workpiece sizes “Everything from a single source: We would be happy to offer you suitable bank financing for your project.” More items – new and used – can be found in our shop! International shipping costs on request!

Condition: used, Haida Lrjdpozgr Eisfx Akmsu Type: HD-B604-S Sensor: TECSIS load cell Max. Capacity: 2T / 20 kN Unit: G, kg, N, LB (adjustable) Resolution: 1/250,000 Accuracy: ± 0.5% Max. Stroke: 700 mm (without fixture) Test speed: 0.1-500 mm/min (adjustable) Voltage: 220V AC ± 10%, 50/60Hz Chuck: 0-7 mm Weight: approx. 175 kg Dimensions (W x D x H): 88 x 50.5 x 150 cm Condition: used Scope of delivery: (See picture) (Subject to changes and errors in the technical data!) We will be happy to answer any further questions you may have by phone.

Condition: like new (used), Year of construction: 1998, functionality: fully functional, Swivel spindle milling machine VEMA TFMS 2-4 Lrsdpfx Ao Afaugokmeu in very good condition, like new; the machine comes from a correctional facility and has only been idle for the past few years; it has been used very little and operated by only one person. VEMA is a company from Northern Germany; the machine's design is similar to the KÖLLE F45 or the PANHANS 240. everything functions perfectly all bearings and guides are in good condition year of manufacture 1998 the machine has the control panel on top with a milling stop that can be adjusted on one side or completely in depth; this is possible with a handwheel in each case. For complete adjustment, there is a mechanical counter; the counter can be set to zero at any point by pressing a button, allowing the stop to be adjusted quickly and very precisely. both stop jaws can also be adjusted individually; there are also 2 mechanical counters, which allow for one-sided adjustment and also enable facing operations, for example, on a gluing profile. the milling stop can be rotated on the machine table the machine has an extra-powerful motor with 7500 watts with pneumatic spindle locking the chips can be removed very well, with 2 extraction ports 120mm with a 30mm spindle that can be adjusted steplessly from -10 to 45°; the spindle is adjusted by handwheel with a mechanical counter. with right/left rotation we will personally deliver and demonstrate the machine anywhere in Germany for 220.00 euros; this means you have no risk when purchasing. Shipping to Austria and the rest of the EU is also possible upon request. with a large table opening that can be reduced by means of various rings; this means that milling cutters with a very large diameter can also be used, and you can also mill safely with small milling cutters (the rings are included, but they are not visible in the pictures). with 3000, 6000, 4500, 7500 and 9000 rpm the spindle height adjustment is also done by handwheel; here too, there is a very precise mechanical counter for reading the height. the table is made of highly ribbed cast iron with an interchangeable spindle (a 40mm spindle can also be used) very robust and durable design; the machine was built for the most demanding milling operations and is suitable for all milling operations. optimal power transmission through belt drive with instruction manual with 3-roller feed HOLZ HER ETX the feed has right/left rotation; the feed rollers are individually mounted and all are like new; it has 8 speeds the machine table is 1020mm wide and 980mm deep + 500mm wide extensions on the left and right the machine can be used immediately 380V, 7500W Weight: approx. 1000kg with all necessary safety devices; the machine is approved by the Holz-BG (German Wood and Furniture Employers' Accident Insurance Association). the machine weighs approx. 1000kg with motor protection switch against overload professional equipment, not cheap hardware store junk optimal, simple, fast and safe handling

Condition: excellent (used), Material Testing Machine / Universal Testing Machine Type: BT2-FA005TN.A50.002 Article No. Base Machine: 1004473 Z005 TN AllroundLine Table-Top The system is a comprehensively equipped ZwickRoell Z005 TN AllroundLine tabletop testing machine. The system has been specifically configured for mechanical and functional testing of automotive injectors and injection systems. In addition, the system features pneumatic sample holders, a visual color recognition system, and a precision scale, as well as extensive product-specific accessories. Technical data: Testing machine: Maximum testing force of the load frame: 5 kN Total testing space height: 1,164 mm Testing space height at the bottom without attachments: 1,030 mm Testing space height at the top without attachments: 1,015 mm Testing space width: 440 mm Crosshead speed: 0.0005 to 3,000 mm/min Return speed: max. 3,000 mm/min Deviation of the drive speed: max. 0.05 % Drive stroke resolution: 0.959431 nm Positioning repeatability: ±2 µm Ljdpfx Akozwvu Njmsru Control: adaptive Control cycle: 1,000 Hz Load cell: Type: Xforce HP Rated force: 0.5 kN / 500 N Suitable for static and dynamic tensile and compressive forces Accuracy class 1 from 1 N Accuracy class 0.5 from 5 N Maximum operating force: 150 % of the rated force Limit force: 150 % of the rated force Breaking force: 300 % of the rated force Protection class: IP54 Connection thread: M28 × 1.5 Connection pin: Ø 20 mm Measuring and control electronics: ZwickRoell testControl II machine electronics DCSC measuring module for strain gauge load cells Measured value acquisition rate: 400 kHz Measured value transmission to PC: 500 Hz Automatic zero point correction Measured signal time correction Ethernet interface to PC Measuring amplifier for strain gauge full bridges Measuring range: 0.2 to 165 % of the rated measured value Measured value acquisition rate of the DCSC module: max. 10 kHz Force measurement technology according to ISO 7500-1 and ASTM E4 Testing device for automotive injectors: Article No.: 3002956 Maximum testing force: 200 N Dimensions: approx. 396 × 235 × 309 mm Weight: approx. 20 kg Pneumatic sample holders: Article No.: 3001461 Maximum testing force: 200 N Maximum opening width: 40 mm Closes on both sides and symmetrically Interchangeable clamping jaws Dimensions of the load frame: Height without base profiles: 1,314 mm Height with base profiles: 1,528 to 2,108 mm Width without base profiles: 680 mm Width with base profiles: 856 mm Width including machine electronics: 1,044 mm Depth with base profiles: 650 mm Depth including machine electronics: 690 mm Weight: Load frame with machine electronics: approx. 161 kg Base profiles: approx. 31 kg Machine with typical attachments: approx. 226 kg + Laser measuring system / visual color recognition system from Keyence + Precision scale: Article No.: 085770 Maximum load: 220 g Readability: 0.1 mg Repeatability at 200 g: 0.1 mg Linearity: 0.25 mg RS232 interface for data transmission Separate weighing cell, display unit and operating terminal + PC with ZwickRoell testXpert III testing software, version 1.2 + Microphone and many other accessories shown in the pictures Condition: used Optical condition according to the pictures Functional scope according to the pictures The complete configuration of all components and accessories, as well as the calibration of the system, must be carried out by the customer themselves. Shipping or freight shipping is possible. Subject to changes, errors and prior sale.

Condition: refurbished (used), Year of construction: 2015, operating hours: 180 h, functionality: fully functional, machine/vehicle number: H5KS, Universal testing machine, type H5kS Extended version by 254 mm With 5KN 500N load cells, screw-type clamping device up to 5kN, and Windows 10-11 software For tensile, compressive, bending, and shear testing, etc., in accordance with EN ISO 7500-1, ASTM E4. The H5kS is a universal testing machine designed according to the latest standards. The machine operates in accordance with the relevant EU radiation protection and safety guidelines (EN 50081-1, 72/23/EEC, EN 61010-1). The maximum voltage within the machine is 48 volts. Special features: • Large, easy-to-read liquid crystal display with backlight • Graphical or numerical display mode • Alphanumeric file input • Speed range 0.001 to 1000 mm/min (2.5kN) • Speed range 0.001 to 500 mm/min (5kN) • High return speed 0.001 to 1500 mm/min • Precise crosshead positioning • Robust load frame • Output of test results with mean value and standard deviation via printer • Wide selection of testing software under Windows for various standards • RS232 interface for use with computer systems • Accuracy of the force display of the load cell: 0.5% across the entire range Lrjdezt S Hmjpfx Akmeu • Accuracy of the displacement display: 0.001 mm • Equipped with a force and displacement alarm system • 32-bit motor controller • 20% digital weight adjustment during calibration of the load cell capacity • Automatic motor alarm for over- or undervoltage and overheating Specifications: • Force measurement accuracy: +/- 0.5% of the displayed force in the range of 2% to 100% • Accuracy of position measurement: +/- 0.01% or 0.001 mm • Accuracy of speed: +/- 0.005% of the selected speed • Operating temperature: 0 to 38°C • Humidity range: 10% to 90% Technical data: • Single-column table model • Maximum load: 5kN in tension and compression • Maximum travel: 1004 mm without clamping device • For further details, please refer to the brochure. Dimensions: Height: 1394 mm Width: 490 mm Depth: 450 mm Weight: 102 kg Connection: Machine: 50-60 Hz - 2000 W Power supply: 220/240VAC

Condition: used, Zwick Type: BT1-FR050TH.A1K 50 kN Material testing machine Lsdpfjzii Ugsx Akmjru Zwick/Roell BT1-FR050TH.A1K material testing machine – Precise strain gauge tests Note: No PC included!! Highlights: Testing force: 50 kN (tensile / compressive) High-precision TC-MODCSCC module for strain gauge load cells (4- & 6-conductor) Measuring range: 0.2 – 165 % nominal value, measurement value acquisition up to 500 Hz Maximum resolution: up to 297,000 points (at 50 Hz) Positioning repeatability: ±10 µm Crosshead speed: 0.0005 – 600 mm/min Robust design, compact dimensions: 1,814–2,688 mm height, 936 mm width, 722 mm depth Low noise: 59 dB(A), ambient temperature +10 to +35 °C, humidity 20–90 % Special features: Ideal for research, development, or industrial material testing Dimensions & weight: Load frame: Testing force (tensile/compressive): 50 kN Load frame height: 1,714 mm Overall height: 1,814 – 2,688 mm Load frame width: 760 mm Overall width: 936 mm Load frame depth: 477 mm Overall depth: 722 mm Weight: With electronics unit: 230 kg With typical attachments: approx. 300 kg Condition: used Scope of delivery: (See picture) ZwickRoell BT1-FR050TH.A1K testing machine Operating manual (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: used, Zwick / Roell Type: BDO-FB0.5TH Zwick / Roell tensile testing machine, table-top testing machine Material testing machine Lodpfezdr Hnex Akmsru BDO-FB0.5TH Testing load in tensile/compressive direction: 500 N Height: 1565 mm, Width: 292 mm, Depth: 469 mm Width of test area: infinite Test area depth: 100 mm Max. working distance without accessories: 1266 mm PC or printer interface: RS 232 Required PC connection (for PC operation): COM 1 Power data: 115/230 V (PH, N, PE) Rated power: 0.4 kVA Mains frequency: 50/60 Hz Weight: 47 kg Condition: used Scope of supply: (autosampler as shown in the picture) (Subject to changes and errors in the technical data; details are subject to change!) We will be happy to answer any further questions you may have by phone.

Year of construction: 2025, condition: repair required (used), functionality: limited functionality, machine/vehicle number: 54942, No minimum price – guaranteed sale to the highest bidder! EXW – Dismantling and loading must be organized by the buyer! TECHNICAL DETAILS Nominal test force: 50 kN Test stroke: < 1,400 mm Usable distance between pressure plates: approx. 800 mm Test area width: 500 mm Test speed: continuously variable 0.001–1,200 mm/min Resolution of displacement measurement: ≤ 0.001 mm Diameter of pressure plates: 246 mm Centering bore: 40 mm Thread: M12 Hardness: ≥ 56 HRC Design: Steel, hardened, rotatable at the top and bottom, lockable at 0° Lrsdpfxez Tf D Rj Akmju Measuring range of the enveloping circle: 30–250 mm Design: Probe with bearing rollers Measurement: Recording under load MACHINE DETAILS Control system: Control system with control computer Test program: Enveloping circle measurement Network: Fast Ethernet, 100 Mbit/s between the control computer and the separately required operating PC Software delivery: USB stick with installation software Documentation: Version and license status not documented separately Last calibration: 08/04/2025 Dimensions & Weight Machine dimensions: approx. 750 × 900 × 1,950 mm Base frame dimensions: approx. 730 × 900 × 700 mm Control cabinet with control computer dimensions: approx. 600 × 600 × 1,900 mm Machine weight: approx. 490 kg Base frame weight: approx. 50 kg Voltage supply: 3 × 400 V AC, 50 Hz, N + PE Type plate power: 3,000 W Connected power: approx. 3 kVA EQUIPMENT Base frame Control cabinet with control computer Rotatable pressure plates Enveloping circle measuring device with probes and bearing rollers USB stick with installation software Compressed air connection: Pneumatic connection with shut-off valve Note: The functionality has been tested and confirmed. However, an unresolved error message on the drive prevents further use. The machine is in like-new condition visually. The operating PC is not included in the offer.

Condition: excellent (used), Material Testing Machine / Universal Testing Machine Type: BT2-FZ1.0TN.D16.001 Base System: zwickiLine Z1.0 TN Special Torsion Multi-Axis Material Testing System 1 kN / 2 Nm Technical Data: Testing Range: Maximum axial testing force Fmax: 1 kN Configured maximum testing torque Mmax: 2 Nm Types of tests: Tensile, compressive, and torsional Axial drive / crosshead: Crosshead speed: 0.0005 to 2,000 mm/min Max. return speed: 2,000 mm/min Speed deviation: max. 0.05 % Path resolution: 0.0554 µm Positioning repeatability: ±2 µm Controller: adaptive Control cycle: 1,000 Hz Testing chamber: Testing chamber height with crosshead angled upwards: 235 to 1,065 mm Testing chamber height with crosshead angled downwards: 90 to 920 mm Testing chamber depth: 105 mm Dimensions of base machine: Height of load frame without head crosshead: approx. 1,289 mm Width with machine electronics: approx. 411 mm Depth with machine electronics: approx. 622 mm Weight of base machine: approx. 76 kg Type: Torsional drive Item No.: 1023835 Maximum drive torque: 20 Nm Rotational speed: 0.01 to 20 rpm Accuracy of set drive speed: 0.05 % Control cycle: 1,000 Hz Axially permissible testing force on the torsional drive: ±5 kN Power connection torsional drive: 230 V / 1 Ph / N / PE Mains frequency: 50 / 60 Hz Power consumption under full load: approx. 2.3 kVA Torque sensor: Item No.: 069536 Rated torque: 2 Nm Limit torque: 150 % of the rated torque Accuracy class 1 from: 0.008 Nm Accuracy class 0.5 from: 0.02 Nm Protection class: IP65 Force sensor: Type: Zwick / Roell Xforce HP Item No.: 069531 Rated force: 1 kN / 225 lbf Max. operating force: 150 % of Fnom Accuracy class 1 from: 2 N Accuracy class 0.5 from: 10 N Protection class: IP54 Measurement and control electronics: Zwick / Roell testControl II Measurement value acquisition rate: 400 kHz Measurement value transfer to PC: 500 Hz Lsdpfx Aszwvtxskmjru Optionally expandable to: 2,000 Hz Control cycle: 1,000 Hz PC interface: Ethernet Measurement signal runtime correction: for all channels Protection class electronics: IP32 Safety device: Swiveling front safety device Electrically monitored interlock Protective screen made of transparent polycarbonate Material thickness of protective screen: 6 mm Dimensions of safety device: Height: approx. 1,237 mm Width: approx. 435 mm Depth: approx. 238 mm Testing tools / accessories: Pneumatic universal holder for pen systems Max. clamping force: 200 N Compressed air supply: 8 bar, filtered and unlubricated Pneumatic 3-finger gripper Max. clamping force: 50 N Compressed air supply: 8 bar, filtered and unlubricated Alignment unit Torque sensor 2 Nm Xforce HP force sensor 1 kN Torsional drive Front safety device Zwick/Roell machine electronics Software: Zwick / Roell testXpert III testing softwareVersion: 1.2 + ALMEMO 2450 universal measuring device Humidity/temperature sensor FHAD4641 + Mettler Toledo precision balance Type: Mettler WXSE + Visual recognition system color Zwick Item No.: 3004644 Vision sensor: IV-G500CA Evaluation unit: IV-G10 Installation distance: 20 to 500 mm + Auto Injector Condition: used Optical condition according to the pictures Functionality according to the pictures The complete configuration of all components and accessories, as well as the calibration of the system, must be carried out by the customer themselves. Subject to changes, errors and prior sale.

Condition: good (used), Year of construction: 2006, functionality: unexamined, Internal article number: 26057 Ledpjzx Scxefx Akmoru Pneumatic press Manufacturer: Schmidt Machine no.: 27-400084 Year of manufacture: 2006 Pressing force: 20 kN Stroke: 100 mm Safety distance: 348 mm Table: 200 x 150 mm Acceptance diameter: 20 mm Max. distance from table to acceptance point: approx. 270 mm Dimensions (L x W x H): 70 x 40 x 100 cm Weight: 60 kg Includes two-hand operation and emergency stop. Attention! The control unit for the machine is missing. The press would have to be operated purely pneumatically. You are welcome to inspect the machine while it is powered on, in our heated warehouse with over 500 m² of space.

Condition: excellent (used), We offer a table-type shot blasting machine – STEM 14x6/2S/2WX1M with a table diameter of 1400 mm. The machine is in very good condition and ready for immediate use. The shot blasting machine has two rotary tables and two turbines, each with a power consumption of 5.5 kW. The designed shot blasting unit is manufactured for semi-automatic shot blasting of the external surface of parts placed on a rotary table. The machine is equipped with two rotary tables. Rotary table diameter: 1400 mm Maximum product height: 600 mm Type: 14x6/2S/2WX1M Year of manufacture: 2009 Total operating hours: 5275 Commissioning date: March 31, 2009 Machine weight: 5000 kg Machine length: 3540 mm Machine height: 5540 mm Machine width: 6600 mm Ljdj Afak Uopfx Akmeru Total power consumption: 20 kW Operating range Shot blasting wheel, number and type: 2 WX1M Outer diameter of shot blasting wheel: 330 mm Shot blasting wheel speed: 2900 rpm Amount of abrasive material discharged per turbine: 80-90 kg/min Amount of abrasive material for initial filling: 500 kg Rotary table diameter: 1400 mm Rotary table speed: 2 rpm Spindle diameter at the front bearing: 105 mm Maximum torque on the spindle: 2500 Nm Distance from the spindle axis to the clamping surface of the table: 60-560 mm Maximum workpiece weight: 500 kg per rotary table.

Condition: good (used), Year of construction: 2013, operating hours: 300 h, functionality: fully functional, machine/vehicle number: H50KS, tractive force with load: 50,000 N, Universal testing machine, type H50kS up to 50KN for tension and compression Load cell 50KN 10KN 1KN and Windows software 8-9-10-or 11 for tension, compression, bending, shear etc., according to EN ISO 7500-1, ASTM E4 The H50kS is a universal testing machine developed according to the latest standards. The machine operates in accordance with the relevant radiation protection and safety directives in the EC. (EN 50081-1, 72/23/EEC, EN 61010-1) The maximum voltage within the machine is 48 volts. Special features - large, easy-to-read liquid crystal display with backlighting - Graphical or numerical display mode - alpha-numeric file input - speed range 0.001 to 500 mm/min. - high return speed 0.001 to 500 mm/min. - exact crosshead positioning - Robust load frame - Output report of results with mean value and standard deviation via printer - Large selection of test software under Windows for various standards - RS232 interface mode for use with computer system - Accuracy of load cell force display 0.5 % over the entire range - Displacement display accuracy 0.001 mm - Equipped with a force and displacement alarm system - 32bit motor controller - 20% digital weight blanking during load cell capacity check - Automatic motor alarm in case of over or under voltage and overheating Lrodpfxsq Ruw Nj Akmeu Specifications: - Force measurement accuracy +/- 0.5 % of the displayed force in the range 2% to 100% - Accuracy of position measurement +/- 0.01 % or 0.001 mm - Speed accuracy +/- 0.005 % of the selected speed - Operating temperature 0 to 38°C - Humidity range 10% to 90% Technical data: - Two-spindle table model - maximum load 50kN in tension and compression - maximum stroke 1100 mm without clamping fixtures - for further details please refer to the brochure Dimensions: Height: 1613 mm width: 720 mm Depth: 500 mm Weight: 140 kg Connection: Machine: 50-60 Hz - 2000 W Power supply: 220/240VAC

Year of construction: 1997, condition: ready for operation (used), Machine is fully refurbished & ready to work with dedicated inspection table ( size 2500 mm long x 850 mm width ), we have more if you need in your factory, price for two or more machine could be under negotiate. The large onion peeler from M&P engineering tops, tails and peels onions of 45mm to 115mm diameter using self adjusting floating knife assemblies over a range of up to 25mm on any one setting. It then slits the onion horizontally from top to tail, the depth of slit is determined by onion quality and grade. The machine finally removes the skin using compressed air providing an end product of optimum appearance. Lredpfx Akjxcal Aomou

Condition: new, Year of construction: 2025, workpiece weight (max.): 12,000 kg, turntable diameter: 280 mm, overall weight: 120 kg, The Robotmover 20 is the ultimate solution for moving heavy loads such as industrial machinery, installations, or steel structures – 100% electric, so zero emissions and noise pollution. Work with unparalleled flexibility thanks to the wireless remote control and the ability to effortlessly change direction 360°. This compact electric mover excels at maneuvering through tight spaces, making it an indispensable tool in congested or confined environments. Thanks to the 48V-60Ah battery, the Robotmover ensures long-lasting operation, saving both time and labor. Lredpfxew I Rt Ns Akmsu Whether you're moving equipment or heavy loads, this electric Robotmover is your reliable partner that streamlines your work and increases productivity. Flexible Operation: The wireless remote control provides infinitely variable drive with 360° direction changes. Strong Traction: The two powerful 1000W motors equipped with magnetic brakes produce a robust pulling force of 20 tons. High Load Capacity: The triple-bearing turntable effortlessly carries a maximum load of 12 tons. Long Battery Life: The 48V lithium-ion battery with a 60 Ah capacity provides 4-5 hours of use without frequent charging. Scope of supply: Robotmover 20, remote control, battery chargers Also available transport crate with garage, battery operated hydraulic jacks, fixed following rollers electric skates power skates machine mover robot mover jung lifting equipment hydraulic jacks

Condition: excellent (used), Year of construction: 1978, functionality: fully functional, I am selling this machine. A video of the machine can be sent via WhatsApp. Lodpfexwl Tbjx Akmsru It can be tested while connected. Very good condition. X 11,500, Y 3,150, Z 2,000, clamping M 100 Includes a support column, 6 pieces of boards with dimensions 6,500 x 1,850 x 400 mm. Rotary table E 20. Heads, etc. This is a complete workstation. Weight approximately 200,000 kg.

Condition: used, Zwick Type: HA 50 Dimensions: H 2685 mm x W 1040 mm x D 750 mm Footprint: 1600 cm² Technical data: Fmax: 50 kN Vmax: 1500 mm/s Working area height max. 1370 mm Working area width 565 mm Accessories: Kistler force sensor 50 kN via NI-Labview Hydraulic unit 280 bar Footprint: 415 cm² Clamping device / specimen holder available (Universal flange, high-strength jaws for specimen holder) Ledpfx Akozil Uiomjru Computer + testXpert R V6.0.0 software Condition: used Scope of delivery: (See image) Weight approx. 1200 kg without frame, etc. (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have by phone.

Condition: good (used), Italdibipack Swing 4255 Shrink wrapping machine The machine is in full working order, ready for production, and in very good condition. The photos show the actual product being sold. Made in Italy. Ljdez S Ulhjpfx Akmsru Description: The „Swing” series of L-sealer shrink wrapping machines is characterized by a compact design, allowing them to occupy less space than other similar systems available on the market. Technical specifications: Sealing bar dimensions: 420 × 550 mm Max. product height: 230 mm Power supply: 230V