Center Lathe

MATRA MD40

Condition: good (used), Year of construction: 1980, turning diameter over bed slide: 1,040 mm, turning diameter over top slide: 710 mm, turning length: 2,000 mm, bed width: 600 mm, Optional chuck 1200 mm 2 Axis RSF Digital read out Conical turning attachment Spindle bore 130 mm Central lubrication Gedjx Tgr Topfx Akajug DBC Turning Length: 2000mm Swing over bed Ø: 1040mm Swing over cross slide Ø:710mm Swing in the gap Ø: 1780mm Gap length: 1000mm Spindle bore: 130mm Bed width: 600mm Tailstock spindle Ø: 130Ø Stroke pinole: 300mm Spindle taper: 6Mk Power: 22kW Speeds / ranges: 600Rpm Feed rate X-Axis: 4000mm/min. Feed rate Z-Axis: 4000mm/min. Length: 6000mm Width: 2100mm Height: 2100mm Weight: 8300kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 1990, condition: ready for operation (used), Two nearly identical Maho milling machines, one with and one without a tool changer, as well as a complete range of accessories/spare parts, are available. Travel X/Y/Z: 600mm/450mm/450mm, tool holder: ISO40, quill stroke: 80mm, spindle speed: 5000rpm, feed rate: 4m/min, rapid traverse: 6m/min. Tool diameter: 130mm/100mm, max. tool length: 250mm, max. tool weight: 6kg. Machine dimensions: approx. 3150mm/3750mm/2150mm, weight: approx. 3600kg. Documentation available. On-site inspection possible. Gusdpfxsxu I Ato Akaeg

Condition: used, Year of construction: 1973, pressure 200 t chamfer lenght 3600 mm distance between columns 2650 mm dayligth 500 mm throat 300 mm stroke 250 mm working feed 10,5 mm/sec Gujdpfx Aot I D U Eskasg return speed 100 mm/sec ram stroke speed 150 mm/sec table height 900 mm oil volume 500 l total power requirement 37 kW weight of the machine ca. 17800 kg dimensions of the machine ca. 3710 x 1800 x 3390 mm Equipment: - Controlled axes Y1 + Y2 - Manual X-axis with digital position display - Set of upper and lower tools - 2x stop fingers - 2x front support arms - Hand and foot controls - Side + rear safety guard - Operating instructions

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide Guedporgzv Njfx Akajg * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: new, table length 2000 mm table width 1200 mm table height 200 mm bore 28 mm weight 843 kg Specifications - High-quality S355J2+N steel + plasma nitriding - Material thickness approx. 24.5–27 mm - Hole diameter 28 mm - Holes in 100×100 mm grid pattern - Rounded corners, edges and holes - Side panel height 200 mm - Hole spacing on side panel: 50 mm Gjdpfx Aoznngrokaeug - Includes scale markings on the surface - Construction reinforced with ribs - Grid lines enable precise set-ups - Special equipment for welding tables is available on request.

Year of construction: 1958, condition: ready for operation (used), Offered is a conventional lathe. Swing diameter over bed: 500mm, swing diameter over support: 300mm, spindle bore: 58mm, taper in the tailstock quill: MT 4, design: conventional leadscrew and feed rod lathe, control: manual. Equipped with three-jaw chuck, four-way tool post, tailstock, chip tray. Weight: approx. 2200kg, overall dimensions X/Y/Z: approx. 2700mm/1100mm/1350mm. Inspection possible by arrangement. Gujdpfezdknwsx Akajg

Condition: used, Year of construction: 2010, operating hours: 11,780 h, Equipment: ABS, all wheel drive, Volvo EXCAVATOR EW140C Gujdpeyltr Asfx Akajg air conditioning 16,850 kg 91 kW Top condition

Condition: new, Year of construction: 2016, 1 unit of a completely overhauled, unused industrial bevel-helical gearbox from ASUG. TGL 21815. All gearbox parts have been replaced, with the exception of the housing!!! Clutch: 800 mm (only one half available) Maximum torque: 27,829 Nm Gear ratio: i = 1:80 Maximum power: 51 kW Oil capacity: 170 kg Speed: n1 = 1400 Speed: n2 = 17.5 Weight: 1450 kg Shaft diameter d1: 65 mm Gjdpfxegwlrde Akaoug Shaft diameter d2: 160 mm Shaft height h1: 500 mm Overall height h2: 925 mm Length of base: 1170 mm !! The gearbox does not have an oil cooler !!

Condition: used, Year of construction: 1952, workpiece length 5000 mm swing dia. 1100 mm clamping length 6000 mm grinding diameter 1100 mm grinding wheel diameter 1300 mm workpiece weight 2500 kg main drive motor 22 kW crankshaft bearing diameter 275 mm steady 100-250 mm speeds of tool 400/500 U/min workpiece turning speeds 20-40 U/min weight of the machine ca. 30 t 13 Grinding Steady Rests Mandrels Mounting Flanges Clamping Devices The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop Godpfxeyt Rxvs Akajug If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: good (used), Refrigerant system Copeland with original condenser Type: D6DT5-320X-AWM/D (x4) Guodpfx Ajg N Hu Sokasg Volume: 126.9 m3/h (x4) Cooling capacity: 220 kW at -10°C/40°C, 56.2 kW at -35°C/40°C Refrigerant: R404A With original condenser Guntner GVH 067B/2x3N Pieces in stock: 1 Condition: Used We have many other refrigeration machines. Chillers, compressors, coolers, condensers, cold rooms, refrigeration and gastronomic furniture as well as machines and devices for restaurants and meat processing. See our other auctions or call us, not everything is available on machineseeker.