LPG Forklifts

Still R70-40 // Hubhöhe 4,97m // Treibgas

Condition: new, 900 mm 900 mm 900x900 mm saw band length 9300 x 67 x 1,1 mm table height 790 mm band speed 14 - 60 m/min total power requirement 11 kW weight of the machine ca. 8,45 t dimensions 4,485 x 1,68 x 3,15 m The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable Nwodpfx Abefg E Hpebjp • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in place near the top edge of the material. After the cut is finished, the tape automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. • The saw band is tensioned via a hydraulic cylinder, which is carried out by the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. • All guided movements are carried out by four recirculating ball guides with one high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Guides. Price on request.

Condition: excellent (used), Year of construction: 2007, Zeppelin Diesel Genset Type: PPO2000 - C32 Nwedjizbdajpfx Abbsp Serial No.: ZPSU1023; Arr.No: 273-9683; Year: 2014; Voltage [V]: 400; Rating [kW]: 1600; Rating [kVA]: 2000; speed [RPM]: 1500; Frequency [Hz]: 50; SMU [hrs]: 0; Application: prime; Layout: Canopy; condition: pre-owned; Notes: Diesel Engine 2 * CAT C32 PPO, new Stamford HC6J alternator, with ComAp automatic Panel Inteli Compact, 2 x circuit breaker, 4000 L in two fuel tank, Jacketwater heater. L/W/H: 11 m,/ 2,3 m/ 3,2 m, weight. 26t, Import duty unpaid.

Year of construction: 1972, condition: good (used), generator, emergency power generator, generator, aggregate, power generator, power unit, emergency power generator, power generation unit -Manufacturer: PILLER/MWM -Power: 730 kVA 50 Hz -Engine: MWM Type TbRHS 518V16 Power 850 HP Speed 1500 rpm -Generator: PILLER NKTB 4-1158 -Note: without control -Individual components: see photos -Transport dimensions: 6 loading meters Nedpfxoivql Io Abbswp -Total weight: 8600 kg

Condition: used, Year of construction: 2009, HOLZ-HER edge banding machine CONTRIGA 1366 Edge thickness: 0.4-30 mm (depending on equipment) Edge height: 51/66 mm (depending on equipment) Panel thickness: 6-45/60 mm (depending on equipment) Edge types: Rolls and strips Feed speeds: Continuous feed from 12-30 m/min (depending on equipment) With adjustable infeed level in the magazine area (max. adjustment range 30 mm) With height-adjustable magazine plate for changing the lower edge overhang With large magazine plate Ø 820 mm for edge rolls up to Ø 800 mm With transport chain including automatic central lubrication With motor-driven, position-controlled bridge height adjustment With pneumatic locking roller for the shortest workpiece sequence With extendable workpiece support (extension width 1600 mm) With space-saving, pneumatically controlled sliding hoods over the entire machine (Deviations for individual units are possible) with motorized infeed guide with injection oiler for lubricating all joints and bolts (including operating hours counter) with central connection for extraction (2x Ø 200 mm) with integrated chip collection box at the end of the machine (when radius scraper unit is installed) PPC 231 control system - Power PC for efficient setup and changeover - 15" SVGA screen with touchscreen - 128 MB CF memory card - USB connector on board - Ethernet network connection - Keyboard connector on board - Windows-like user interface - all information in plain text and/or graphics - Rotatable and pivoting control panel at eye level - Dust-proof membrane keyboard with softkeys (pushbuttons) - LED display for unit preselection - Program list with program names and numbers - Extensive program memory - Individual selection of the units with the functions as basic setting options for setpoints, route points and tool corrections as well as the fixed route points - Centralized and clear setup processes for units and their axis settings via fine adjustment (depending on the equipment) - Interval display for the shortest workpiece distance - Integrated path control - Path points are controlled generally or program-specifically - Clear and complete recording of all operating data - Service messages in plain text - Diagnostic system - including integrated synchronous bus system for high precision in unit control - Individual administration for up to ten users, including password protection - Online maintenance (optional), data exchange with HOLZ-HER Service - Barcode interface (optional) BASIC MACHINE CONTRIGA 1366 - Belt bridge Options and accessories for the basic machine Spraying device 1856 for the inlet and outlet area For the inlet area: Electronically controlled release agent sprayer with Riepe-LPZ/II release agent For the outlet area: Electronically controlled cleaning agent sprayer with Riepe-LP163/93 cleaning agent (only in conjunction with pre-milling unit 1961 and surface scraper 1964) Joint milling unit Joint milling station 1803 (2x 2.6 kW, 200 Hz, 12000 min-1) With two plunge-controlled milling units 1 unit in up-cutting direction 1 unit in down-cutting direction Plunge path 5 mm With static frequency converter 200 Hz Without milling tool With ProLock screw-in clamp for fast tool changes Tool for 1803 (workpiece height up to 60 mm) Diamond milling cutter PRO UT 2 pieces (front and rear) including protective covers Ø 100-63 - Ø 30 mm, Z = 3 + 3 + 3, 1x left-hand rotation, 1x right-hand rotation Noise-reduced milling cutter with integrated chip guide DFC technology (Leitz syst Nodpfovvkfdox Abbewp

Year of construction: 2020, condition: refurbished (used), Dear customers! Our experience has shown that the communication by e-mail usually drags out everything unnecessarily. We would like to help you quickly, but it is better to spend three minutes on the phone than three days writing e-mails back and forth. T.S.W.C. 30.20 Dry bulkhead Dimensions: 3000 x 2000 mm W X H + Fan in the height Air capacity: 10.800 m³ / h Motor: 2,20 kW ex-proof Exhaust air pipe: 500 Ø mm depth: 900 mm Double filtration: paper filter + Paintstop filter mat over Terminal strip (+180,- EUR net) Nwedpofn Nddefx Abbjp Options/additional price for: Paintstop filter mat terminal strip: 180,- EUR net side baffle plates with hinge: 590,- EUR net Pictures may vary. We can also offer you complete spraying rooms with supply air system, heat exchanger, supply air ceiling, piping etc. Just contact us.

Condition: used, Year of construction: 1988, machine/vehicle number: 1743, UV-Beschichtungsmaschine - UV-Coating machine Billhöfer Gula Speed CGS JKN 112Year 1988 - Serial-No. 1743 Format min. 300 x 500mm Format max. 820 x 1120mm Feeder automatic Mabeg Grammatur 60 up to 500 gr/m2 card board Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Nodpfjh Axqujx Abbswp Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: excellent (used), Year of construction: 2012, Technical Data: Nsdpfx Abjxdt Umobewp Working length: 4100 mm Distance between uprights: 3550 mm Press force: 300 tons CNC control: DELEM EPC-3D Controlled axes: Y1/Y2; X; R; Z1/Z2 Hydraulic tool clamping top and bottom: WILA system CNC crowning Stroke: 550 mm Throat depth: 405 mm Installation height: 620 mm 2 bending aids Angle measuring system Motor power: 30 kW Laser monitoring Table height: 980 mm Dimensions (L x W x H): approx. 5550 x 2950 x 3400 mm Weight: approx. 24.5 tons Accessories: Manual tool changer Segmented bending with step-by-step support of the bending aids (segment bending) 1 set of tools Condition: Very good condition The seller assumes no liability for typing or data transmission errors. The machine’s appearance, technical condition, and wear are consistent with its age; used machines are sold without any warranty.

Condition: used, Year of construction: 2013, Technical data Machine length: 6060 mm Machine width: 1555 mm Machine height: 2300 mm Weight: 2600 kg Total power input: 21 kW (30 A) Compressed air: 6 bar Air consumption: approx. 350 l/min Extraction: 2820 m³/h (at 28 m/s) Technical features and equipment General functions Workpiece thickness: 8–60 mm Max. feed speed: 18 m/min Double pressure from above for stability of the part Electronic thickness control Frequency converter for feed Automatic lubrication of the feed chain Automatic motor calibration Touch control system Emulsion spray at the inlet and outlet Nsdpfx Asv Szt Dobbewp Edge preheating Pre-milling unit Tool diameter: 100 mm Tool height: 63 mm Diamond tool with replaceable knives Motorized removal adjustment Gluing unit Glue and hot air application Heated application roller Quick exchange of the entire unit Automatic position adjustment via motor 3 pressure rollers Edging speed: 14 m/min Cutting unit Twin-motor unit with automatic tilting Tilt up to 15° THK prismatic guide Radius milling unit 2 tools Automatic adjustment in two axes Automatic overlap adjustment Copying unit (2 motors) Automatic tool position change by servo motor Electromagnetic horizontal movement Vertical hydraulically damped movement

Condition: used, mileage: 4,10,000 km, power: 309 kW (420.12 HP), gearing type: automatic, fuel type: diesel, color: white, overall weight: 37,000 kg, axle configuration: > 3 axles, first registration: 02/2010, emission class: euro4, Equipment: air conditioning, had accident, VOLVO FM 420/ RIGHT-HAND DRIVE !!!! Limited roadworthiness !! Severe air loss !!! Compressor does not supply air !! NO VEHICLE REGISTRATION DOCUMENT available !!! But confirmation from a lawyer is included !! 8x4 Engine runs !! Steel suspension I-Shift Alloy wheels Air conditioning Rear tipper etc.... Nwsdpfx Abew Eqzcjbep

Condition: excellent (used), Year of construction: 2015, operating hours: 27,500 h, Operating hours: 27,500 h Laser on: 17,000 h Njdpfx Abexbfvwsbewp Resonator: 5KW Price on request