CNC turning and milling center

Traub TNC65

Condition: good (used), Year of construction: 2001, Ref. -No.: 10551 Iedpfx Aoxxpbrob Ija Manufacturer: TRAUB Type: TNC 42/65 Year of construction: 2001 Type of control: CNC Control: TRAUB TX Storage location: Halberstadt Country of origin: Germany Machine-No.: 93XXXXX Turning Speeds: 8000 RPM X stroke: 450 mm Turning Length: 450 mm Spindle Speeds: 4000 RPM Clamping Diameter: 42 / 65 mm Spindle Diameter In Front Bearing: 110 mm Tool Taper: 14 Max. Torque: 170 / 230 Nm Rapid Travel Speed X-Axis: 15 m / min Rapid Travel Speed Y-Axis: 6 m / min Rapid Travel Speed Z-Axis: 30 m / min Dimensions Of The Machine (Lxwxh): 4354 x 2076 x 1917 m Chisel slide cross section turning and milling support: 16 x16 ( 20 x20 ) mm Pressure: 70 bar hydraulic tank: 70 L. Total Power Requirement: 39 kVA Weight Of The Machine Ca.: 5,2 t Feed force X-axis at 100% duty cycle: 5000 N Feed path X-axis: 140 mm Z-axis feed path: 450 mm Y-axis feed path: 35 mm Ball screw Z-axis (Ø x pitch): 32 x 10 mm Ball screw X-axis (Ø x pitch): 32 x 5 mm Ball screw Y-axis (Ø x pitch): 25 x 5 mm Further information: - Revolver 1 Number of branches 10 - Revolver 2 Number of branches 14 - Hecowpkfie Htlx Tfefh - Powered tools Yes

Condition: excellent (used), Year of construction: 1996, operating hours: 46,282 h, rapid traverse X-axis: 15 m/min, rapid traverse Y-axis: 15 m/min, rapid traverse Z-axis: 15 m/min, total height: 2,600 mm, total length: 11,000 mm, total width: 2,000 mm, overall weight: 6,000 kg, controller manufacturer: TRAUB, controller model: TX 8F, counter spindle speed (max.): 4,000 rpm, number of slots in tool magazine: 10, - Includes two 10-position tool turrets with driven tool stations - Includes HAINBUCH chuck system - Includes sub-spindle, bar feeder (manufacturer: STAMAG) - Includes chip conveyor TECHNICAL DATA: - Operating voltage: 400 V - Frequency: 50 Hz - Control voltage: 230 V Iodpswpa Rusfx Ab Isa - Rated current: 85 A - Connection: 54 kW - Connected load: 39 kW - Noise emission value at operator position: 71 dB(A) Ambient conditions: - Temperature: 5 – 40°C - Air humidity: max. 70% - Workpiece removal via sub-spindle - Max. sub-spindle speed: 4000 min-1 - Max. workpiece diameter: 56 mm - Programming: EIA and ISO code Input and output resolution: - X/Z: 0.001 mm - C axis: 0.001° - Rapid traverse: max. 15 m/min - Fine interpolation cycle: 0.34 ms - Largest thread pitch: 999.999 mm - Largest radius: 99,999.999 mm - Feed override: 0…200% - Rapid traverse override: 0…100% - Speed override: 50…120% - Speed input: 5 digits - Cutting speed input: 4 digits - Tool input: 4 digits - Program number: 8 digits - Subprogram number: 8 digits - Block number: 4 digits - M-functions: 3 digits - B-functions: 6 digits - Memory capacity: 32,000 characters - Tool correction pairs: 40 NUMERICALLY CONTROLLED TURNING AND POSITIONING UNIT (C AXIS): Main spindle: - Max. speed: 80 min-1 - Torque at 100% duty cycle: 100 Nm - Accuracy: +/- 3 min Sub-spindle: - Max. speed: 80 min-1 - Torque at 100% duty cycle: 30 Nm - Accuracy: +/- 3 min TOOL CARRIER 1 & 2: - Driven tools per tool carrier: 10 (14) - Max. speed: 4000 (8000) - Power at 100% duty cycle: 1.5 kW - Power at 15% duty cycle: 4 kW - Torque at 15% duty cycle: 12.4 (4) Nm - Tool holder/tool carrier quantity: 10 (14) - Cylindrical shank as per DIN 69880: Ø 30 x 55 (25 x 48) mm - Chisel cross-section: 20 x 20 (16 x 16) mm - Chip-to-chip time (per VDI 2852): 1.2 s - Switching time one station: 0.6 s - Over 5 stations: 1.5 s SUB-SPINDLE (NUMERICALLY CONTROLLED IN Z DIRECTION): - Max. speed: 4000 min-1 - Max. clamping diameter: 65 mm - Three-phase motor steplessly programmable: 11 kW - Torque: 210 Nm - Feed force at 100% duty cycle: 6000 N - Feed travel: 520 mm - Ball screw operation: Ø 32 x 10 mm HYDRAULICS: - System pressure: 60 bar - Tank capacity: 150 l COOLANT LUBRICATION: - Per tool carrier: 1-stage centrifugal pump - Pump pressure: 5/12 bar - Tank capacity: - without chip conveyor: 300 l - with chip conveyor: 280 l NOTICE: Due to sporadic work, the operating hours may still change slightly.

Condition: used, Year of construction: 2003, max. bar material dia. 65 mm max. bar length 3.000 mm control System TX 8H CNC lathe | TRAUB - TNC 65 equipped with bar loader . The machine is in a well-maintained condition and can be inspected at any time under power. The machine videos from the production plant will be shared on request. Technical data of the machine will follow soon. We ask for your understanding ! - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags: TNC65 | TNC-65 Iodsxbtp Eepfx Ab Ioa

Condition: used, Year of construction: 2004, controller manufacturer: Mitsubishi, controller model: TX-8i, _____ Description: Year of manuf. : 2004 Control : Mitsubishi TX-8i Turning length : 450 mm Mainspindle: Technology:Belt-driven spindle Speed:4.000 rpm Isdpfxjxhbfno Ab Iea Power:18,5 kW Torque:230 Nm Barcapacity:65 mm Workpiececlamping:Collet chuck, Hainbuch Spanntop Gr. 65 Subspindle: Technology:Belt-driven spindle Speed:4.000 rpm Power:11 kW Torque:210 Nm Workpiececlamping:Collet chuck, Hainbuch Spanntop Gr. 65 Ejector:Hydraulic with flush Movement in Z:520 mm Rapid travers in Z:30 m/min Toolcarrier I (X/Y/Z): Technology:Turret with 10 stations Taper:VDI30 Tooldrive:4.000 rpm, 4 kW, 16 Nm Movement in X/Y/Z:140/70/450 mm Rapid travers in X/Y/Z:15/6/30 m/min Toolcarrier II (X/Z): Technology:Turret with 10 stations Taper:VDI30 Tooldrive:4.000 rpm, 4 kW, 16 Nm Movement in X/Y/Z:140/450 mm Rapid travers in X/Y/Z:15/30 m/min Equipment/Accessory: Chipmanagement:Chip conveyor Coolingmanagement:Cooling unit with Paperbeltfilter Rawmaterialfeed:Barlaoder, FMB SL80S Finished part removal:Hydraulic part catcher with coneyor belt Oilmistseparation:Electrostatic extraction, LTA AC3001 Further Accessory:Misc. Toolholder, Rinsing pistol

Year of construction: 1996, condition: ready for operation (used), Turning length: 450mm, spindle clearance: 65mm, speed: 4000rpm, main spindle/counter spindle power: 18.5kW/11kW, tool positions: 10, driven tools: 10, hydraulic capacity: 150l, hydraulic pressure: 60bar, connected load: 39kW. Rapid traverse X1/X2: 15m/min, feed force: 5000N, feed path: 140mm. Rapid traverse Z1/Z2: 30m/min, feed force: 8000N, feed path: 450mm. Rapid traverse Y1: 6m/min, feed force: 8000N, feed path: +/-35mm. Machine dimensions X/Y/Z: approx. 4150mm/2000mm/1800mm, weight: approx. 4750kg, control: Traub System TX 8F, operating hours: 78825h. Documentation available. On-site inspection is possible. Iodpfx Absv Scrho Ija

Condition: reconditioned (used), Year of construction: 2005, functionality: fully functional, Traub CNC lathe TNC65DGY, TX8I, year 2005, serial no. 1130 Description Y-axis on S1, V-axis, 2x C-axis, 2x rotary tool drive, 2 VDI30 turrets, Hainbuch BZI65 on main and counter spindle, parts gripper, Iemca Master 880MP-E loading magazine, Isdjwi I Eyspfx Ab Ija Condition Very well maintained, good condition, serviced. Machine geometry has been checked and corrected/adjusted. Machine can be viewed under power – video available. 6-month warranty on main components as follows: Spindle bearings, ball screws, linear guides, clamping cylinders. The warranty expressly applies only to spare parts, not to downtime, labor, or travel time. The warranty expressly does not apply to parts other than those listed above, e.g., wear parts, electrical, electronic, hydraulic, etc.

Condition: ready for operation (used), Year of construction: 1996, operating hours: 38,433 h, functionality: fully functional, machine/vehicle number: 489, bar diameter (max.): 65 mm, controller model: TRAUB TX8F, bar length: 3,000 mm, number of axes: 7, Equipment: bar feeder, chip conveyor, CNC automatic lathe with seven axes as well as main and counter spindle! TECHNICAL DETAILS Axes and spindles Number of axes: 7 Main spindle: present Counter spindle: present Number of turrets: 2 C-axes: 2 Y-axis: 1 Control: TRAUB TX8F MACHINE DETAILS Ijdpfxew Uikto Ab Ioa Operating hours: 38,433 hours EQUIPMENT Bar loading magazine Stamag DN61 (bar diameter 65 mm, bar length 3 m) Coolant system Parts discharge Chip conveyor Air filter

Condition: not inspected (used), Year of construction: 1996, operating hours: 46,282 h, functionality: unexamined, machine/vehicle number: 18770, controller model: TX 8F, clamping diameter: 65 mm, counter spindle speed (max.): 4,000 rpm, workpiece diameter (max.): 56 mm, No minimum price – guaranteed sale to the highest bidder! Payment deadline for the machine is 20.11.2025! Bidding obligates the buyer to collect within the collection period from 01.12.2025 to 05.12.2025! TECHNICAL DETAILS Max. workpiece diameter: 56 mm Max. clamping diameter: 65 mm Max. counter spindle speed: 4,000 rpm Counter spindle power: 11 kW Counter spindle constant power range: 1:8 Counter spindle torque: 210 Nm Tool drive Max. tool drive speed: 4,000 rpm Tool drive power at 100% duty cycle: 1.5 kW Tool drive power at 15% duty cycle: 4 kW Tool drive torque at 15% duty cycle: 12.4 Nm (4 Nm) Number of tool stations: 10 (14) Cylindrical tool holder: ∅ 30 x 55 mm (25 x 48 mm) Tool shank cross section: 20 x 20 mm (16 x 16 mm) Chip-to-chip time: 1.2 s Ijdpfx Aoxpgl Ajb Isa Indexing time per station: 0.6 s Indexing time over 5 stations: 1.5 s Positioning unit X/Z: 0.001 mm Positioning unit C-axis: 0.001° Fine interpolation increment: 0.34 ms Max. thread pitch: 999,999 mm Max. radius: 99,999.999 mm Max. speed (C-axis): 80 rpm Torque (main spindle C-axis) at 100% duty cycle: 100 Nm Accuracy (main and counter spindle C-axis): ± 3 min Rapid traverse and path speed: 30,000 mm/min Rapid traverse: max. 15 m/min Thrust at 100% duty cycle: 6,000 N Travel distance: 520 mm Ball screw size (∅ x pitch): 32 x 10 mm Feed override: 0 – 200% Rapid traverse override: 0 – 100% Spindle speed override: 50 – 120% MACHINE DETAILS Control: TX 8F Dimensions & Weight Dimensions (L x W x H): 11,000 x 2,000 x 2,600 mm Weight: 6,000 kg Electrical Data Operating voltage: 400 V Frequency: 50 Hz Control voltage: 230 V Nominal current: 85 A Connection rating: 54 kW Power consumption: 39 kW Noise emission at operator position: 71 dB(A) Temperature range: 5 – 40 °C Max. humidity: 70% System hydraulic pressure: 60 bar Hydraulic tank capacity: 150 l Coolant pump pressure: 5/12 bar Tank capacity without chip conveyor: 300 l Tank capacity with chip conveyor: 280 l Input Spindle speed input: 5 digits Cutting speed input: 4 digits Tool input: 4 digits Program number: 8 digits Subprogram number: 8 digits Block number: 4 digits M-codes: 3 digits B-codes: 6 digits Memory capacity: 32,000 characters Operating hours: 46,282 h (as of 17.10.2025) EQUIPMENT Two 10-station tool turrets with driven tool stations HAINBUCH chuck system Counter spindle Bar feeder from STAMAG Chip conveyor

Condition: used, Year of construction: 1996, max. bar material dia. 65 mm max. swing diameter 175 mm max. bar length 3.000 mm Iedpfx Aoxbtq Njb Isa control System TX 8F travel -x axis 140 mm travel -z axis 520 mm CNC lathe | TRAUB - TNC 42/65 DG equipped with bar loader. The machine is in a well-maintained condition and can be inspected at any time under power. The machine videos from the production plant will be shared on request. Technical data of the machine will follow soon. We ask for your understanding ! - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags: TNC65 | TNC-65 |TNC 42-65 DG | TNC 42/65DG

Year of construction: 2015, condition: ready for operation (used), A CNC double-spindle lathe Traub overhauled in 2025 is available. Turning length: 450mm, spindle clearance: 65mm, speed: 4000rpm, main spindle/counter spindle power: 18.5kW/11kW, tool positions: 10, driven tools: 10, hydraulic capacity: 150l, hydraulic pressure: 60bar, connected load: 39kW. Rapid traverse X1/X2: 15m/min, feed force: 5000N, feed path: 140mm. Rapid traverse Z1/Z2: 30m/min, feed force: 8000N, feed path: 450mm. Rapid traverse Y1: 6m/min, feed force: 8000N, feed path: +/-35mm. Machine dimensions X/Y/Z: approx. 4150mm/2000mm/1800mm, weight: approx. 4750kg, control: Traub System TX 8F, operating hours: 12938h. Including chip conveyor and bar loader LNS Quick Load. Documentation available. On-site inspection is possible. Iedpjv Scrbsfx Ab Iea