Lifting tables

UWM UWM 3000

Condition: new, table length 2200 mm table width 1500 mm stroke height 1900 mm weight max. in kg 3000 kg total power requirement 1,5 kW stroke speed - idle stroke upwards 55 sek. stroke speed - idle stroke downwards 30 sek. connected load frequency 400 V weight of the machine ca. 0,650 t Hnodpfx Adjvn U D Ieweg dimensions of the machine ca. 2,2 x 1,5 x 0,3 m The hydraulic lifting tables are electrically driven and operated. Have a contact strip for safe lowering operation. Wide applicability for workshops, assembly departments, loading pits, etc.

Condition: excellent (used), Year of manufacture: 1991 Model: ITPS III Serial number: ITPS 80C 25 P1C226 Maximum pressing force: 1800 kN Working stroke: 115 mm Power supply: 415 V, 50 Hz, 3 phases Rated current: 119 A Hsdpfx Adewq Dpqowsng Installed power: 18.5 kW Machine weight: 4940 kg Inventory number: 9.14 Control: Delem DA-65R The machine starts up, but the control unit does not respond to commands. The previous owner replaced the original AMADA control with a DELEM unit.

Year of construction: 2012, condition: used, fuel type: electric, weight max. in kg 2500 kg stroke 3700 mm fork length 900 mm Super elastic battery Baujahr 2013 construction height 2630 mm weight of the machine ca. t Hnedpefibh Refx Adwjg Duplex / Free lift

Condition: new, functionality: fully functional, Year of construction: 2025, Box Type Electrostatic Powder Coating Oven: Length: 500cm, Width: 250cm, Height: 300cm Hnsdpfjv Nvndox Adwog - Powder Coating Booth with Filter: Length:300cm, Width:220cm, Height:270cm - Electrostatic Powder Coating Equipment: Model: HMK MULTICOLOR, Type of Use: Manual

Year of construction: 1995, condition: ready for operation (used), A Promecam (Amada) APX 103 CNC press brake is available. Pressing force: 1000kN, working width: 3000mm, column distance: 2550mm, gap opening: 370mm, stroke: 100mm, column depth: 400mm, infeed speed: 70mm/s, bending speed: 9mm/s, return speed: 85mm/s, drive power: 10.5kW. Machine dimensions X/Y/Z: approx. 3500mm/2200mm/2300mm, weight: approx. 6400kg, control: Amada Operator, operating hours: 36261h. The press is still in operation, therefore the operating hours change continuously. Documentation available. On-site inspection is possible. Hnsdowm Nn Ropfx Adwog

Condition: used, Year of construction: 1998, machine/vehicle number: 100057, 1998 AMADA VIPROS 2510 KING The punching machine is in good condition, always serviced on time by Amada service. All documentation is included. This machine can be operated with a punching force of 196 kN. Made in Japan. The punching machine is still under power and can be tested at any time in Vilnius, Lithuania. Specification: Model: AMADA VIPROS 2510K Serial no: 100057 Year: 1998 Made in: Japan Punching force: 20 tons Stations: 31 Tools: included (RO 6; RO 6,5; RO 3; RE 30x5; RE 25x5; RE 80x5; RO 5; RO 3,5; RE 10x3; RE 10x5; RE 50x5; RE 8x12) Maximum sheet thickness: 3 mm Hedpfx Adom Ncayswsng X-axis movement: 2500 mm Y axis travel: 1270 mm Weight: 11 000 kg Location: Vilnius, Lithuania Testable: Yes If you have any questions, please do not hesitate to contact us.

Condition: like new (used), Year of construction: 2004, AMADA MODEL HFT 8025 80 tons capacity x 2500 bending length hydraulic downstroking press brake complete with CD 2000 4 AXIS colour graphic cnc control, Hsdpou A Dgrefx Adwsng ERWIN SICK machine mounted electronic guards , side and rear interlocked fencing Model Amada HFT 8025 downstoke CNC Press brake Year 2004 Tonnage 100 KN Type CD 2000 CNC Controlled Axis Y1, Y2, X, R Max. Bend Length 2500 mm Open height 470 mm Stroke Length 350 mm Approach Speed 100 mm/sec Bending Speed 1 - 10 mm/sec Return Speed 1-100 mm/sec Oil Capacity Motor Power 7.5kw Weight 6100 kg Bed Length 2500 mm Bed Width 60 mm Open Height 470 mm Throat Depth 420 mm CNC Control Backguage Stoke (X axis) 700 mm/s Max gauge 1000mm R axis 250mm can be demonstrated under power BROCHURE AND FURTHER INFORATION AVAILABLE UPON REQUEST

Condition: good (used), Year of construction: 1995, Double girder traveling crane, bridge crane, overhead crane, assembly crane, workstation crane, ceiling-mounted traveling crane, traveling crane, crane system -with 2x electric cable winches -Load capacity: 2 x 1600 kg -Bridge load capacity: 3.2 tons -Wingspan: 6.4 m -Hallway service Hnsdpfx Ajb A Ny Eodwog -Dimensions: 2000/6400/H1000 mm -Weight: approx. 2000 kg

Condition: used, CNC Press Brake AMADA Type HFBO 50 x 2000 Serial No. HFBO 50 20 S60906 Year of manufacture: 1996 Press brake with 8 axes - CNC control Operator II Pressing force: 50 tons Working length: 2090 mm Stroke: 200 mm Frame depth: 420 mm Distance between side frames: 1660 mm Max. tool installation height: 460 mm Hnjdpfx Aow Iq Ugsdwog Table width: 60 mm Table height above floor: 910 mm Motor power: 4.5 kW Mains connection: 400 Volt, 50 Hz, 20 Amp. - 8-axis CNC control Operator II (Y1-Y2 / X1-X2 / Z1-Z2 / R1-R2) - 2 freely programmable backgauge fingers, movable laterally and in height (Z1+Z2+R1+R2) - Press beam with servo valves and measuring system Y1 and Y2 - Operation via electric foot switch and/or two-hand control panel - Mechanical lever-style tool clamping for the upper tool (5 AMADA Expert, 5 UKB 50.667 H=120 mm) - Tool holder for lower tool, 60 mm wide - 11-piece upper tool set, 30°, total length 1675 mm - consisting of: 1x 835 / 1x 300 / 1x 165 / 1x 50 / 1x 45 / 1x 35 / 1x 20 / 1x 15 / 1x 10 / 2x 100 mm (end pieces) in length - 2-piece lower tool, 88° - V8, total length 1250 mm - consisting of: 1x 835 / 1x 415 mm in length - Indicated operating hours: 30,537 h - Operating manual, electrical diagram, spare parts book included Weight: 4,700 kg Good condition

Condition: used, Year of construction: 2001, pressure 50.0 t chamfer lenght 2090 mm distance between columns 1665 mm column arm 400 mm table width 60.0 mm ajustment speed 100 mm/sec working feed 10.0 mm/sec return speed 92.0 mm/sec stroke 200 mm table height 910 mm dayligth 470 mm Number of working hours 36.160 h total power requirement 6.0 KW weight of the machine ca. 4850 kg Hnjdpfx Adsxabutswjg range L-W-H 3458 x 2450 x 2450 mm with only approximately 36.160 operating hours (!!) - Inspected condition - Machine video - ?v=x8Z0h2_wA6s Equipment: - CNC electro-hydraulic press brake - CNC control type OPERATEUR 2 with 8 axes (X1+X2, Y1+Y2, R1+R2, Z1+Z2) * CNC-controlled backgauge adjustment (X-axis) * CNC-controlled vertical adjustment of the stop fingers (R1+R2) * CNC-controlled left-right adjustment of the stop fingers (Z1+Z2) * Hand control unit for manual axes movement * Pivoting control, front left - AMADA/PROMECAM quick clamping system for the upper tool * 1 split set of offset upper tools (UKB 10.512) - AMADA/PROMECAM bottom tool holder * 1x split set of 1-V dies (UKB 20.810) - Side guards (hinged doors) - Rear guards (hinged door) - CE marking - 1x freely movable double foot switch - Operating instructions (PDF)