ИП Мкртчян Т М

Condition: used, Refurbished granulator, heavy-duty series, hard-faced Can be used for dry and wet shredding Hodpfezuytksx Achonr Typical applications: Plastic hollow bodies, secondary shredding of pre-shredded waste, Rotor 800 mm diameter x 1600 mm width Open F7 rotor with replaceable blade supports Drive power 160-250 kw With forced feeding by 3 load-dependent controlled feed screws Hydraulically hinged, hydraulically swiveling screen basket Throughput capacity up to 5 t/h depending on material and grain size

Condition: used, This package includes: 3 x uprights at 3,000mm x 1,100m (blue) 8 x crossbeams at 2,700mm (yellow) 16 x safety pins This creates a single row of shelving with 2 bays and 2 levels + floor space = 18 pallet spaces (1,000 kg / pallet) Approximately 250 uprights and 2,000 crossbeams are available for this system. Simply contact us. Manufacturer: Jungheinrich Type: MPB Condition: used, good condition Height: 3,000 mm Length: approx. 5.50 meters Shelf depth: 1,100 mm Bracing: bolted Crossbeam length: 2,700 mm Shelf load: 3,000 kg Bay load: 6,000 kg Pallet spaces: 18 Accessories such as: Floor mounting Connectors Load warning signs Impact protection Guardrails Grid decks Rear panel grids Deep shelf supports Barrier rails and much more... Just ask us! Hnsdpfx Ajzuyr Tschor "Benefit from over 20 years of industry experience – we provide you with competent and personalized advice as your experienced specialist dealer for new and used shelving systems." Sales and Delivery Conditions (B2B) - Prices & Logistics: All prices are quoted net ex works. Express delivery via our own fleet is possible after individual consultation. - Offer Status: All offers are subject to availability. We reserve the right to sell goods that are still in stock. - Reservation of Ownership: The goods remain our unrestricted property until full payment has been received (no right of disposal or processing). - Warranty: Exclusive distribution to commercial enterprises (§ 14 BGB). No warranty for defects in used and IIa goods. For new goods, the respective manufacturer's warranties apply.

Condition: good (used), The scope of delivery includes: 1x bracket for rear wall grid, used Material color: hot-dip galvanized Hsdpozuyr Hefx Achenr Internal designation: Variant 1 Diagonal length: approx. 410 mm Total width: approx. 90 mm Overhang: approx. 225 mm Material thickness: approx. 3.00 mm Weight/piece: 0.71 kg 2 elongated holes: 50 x 9 mm (W x H) Height: 30 mm General information about the item: This item is offered for pick-up only. Any additional transport or shipping of this item will incur extra costs, which can be requested separately depending on the delivery location and scope of delivery.

Condition: ready for operation (used), Year of construction: 2023, machine/vehicle number: 231458, functionality: fully functional, travel distance X-axis: 3,700 mm, travel distance Y-axis: 2,100 mm, travel distance Z-axis: 370 mm, spindle speed (max.): 6,000 rpm, table load: 800 kg, TECHNICAL DETAILS Travel range X-axis: 3,700 mm Travel range Y-axis: 2,100 mm Travel range Z-axis: 370 mm Rotational range C-axis: 0–362° Swivel range A-axis: 0–90° Travel time C-axis (0–392°): 3 s Travel time A-axis (0–90°): 2 s Spindle speed: 6,000 rpm Spindle power: 16.5/56 kW Speed X-axis: 30 m/min Speed Y-axis: 30 m/min Speed Z-axis: 5 m/min Dimensions of tilting table: 3,500 × 2,000 + 500 mm Load capacity: 800 kg MACHINE DETAILS Stainless steel cover for saw blade with opening for cutter: Ø 425 mm Stainless steel cover for saw blade: Ø 625 mm Total power consumption: 23 kW Water consumption for saw blade: 30 L/min Total weight: 4,800 kg EQUIPMENT Material and saw blade measuring system Vacuum system for moving the panels Camera with software for management Pneumatic tilting table Motorized rotary head (C-axis) Motorized saw blade inclination (A-axis) Stainless steel cover for saw blade with opening for cutter Hnsdpfxszuyryo Achsr Stainless steel cover for saw blade

Condition: used, This package includes: 38 x crossbars, 2,700 mm each (yellow) 76 x locking pins - Remaining stock - Manufacturer: Tegometall Condition: used, good condition Crossbar length: 2,700 mm Crossbar height: 130 mm Shelf load capacity: 2,700 kg Accessories such as: Hodpfx Acezuyrtohsnr Floor mounting Connectors Load warning signs Impact protection Guard rails Grating Rear panel grating Deep shelf supports Barrier rails and much more... Just ask us! "Benefit from over 20 years of industry experience – we provide competent and personalized advice as your experienced specialist retailer for new and used shelving systems." Sales & Delivery Terms (B2B) - Prices & Logistics: All prices are quoted net ex works. Express delivery via our own fleet is possible after individual consultation. - Offer status: All offers are subject to change. Items may be sold subject to prior sale. - Retention of title: Ownership of the goods remains with us until full payment has been received (no right of disposal or processing). - Warranty: Exclusive sale to commercial enterprises (§ 14 BGB). For used and IIa goods, liability for defects in materials and workmanship is excluded. For new goods, the respective manufacturer's warranties apply.

Condition: used, This package includes: 20 x crossbeams, 2,700 mm each (yellow) 40 x securing pins - Remaining stock - Manufacturer: Tegometall Condition: used, good condition Crossbeam length: 2,700 mm Crossbeam height: 140 mm Shelf load capacity: 3,000 kg Accessories such as: Floor mounting Connectors Load warning labels Impact protection Guard rails Grating Back panel grating Deep shelf supports Barrier railings and much more... Just ask us! "Benefit from over 20 years of industry experience – we will provide you with competent and personal advice as your experienced specialist retailer for new and used shelving systems." Hsdpfxjzuyrmo Achenr Sales and Delivery Conditions (B2B) - Prices & Logistics: All prices are quoted net ex works. Express delivery via our own fleet is possible after individual consultation. - Offer Status: All offers are subject to change and non-binding. We reserve the right to sell items in the meantime. - Reservation of Title: The goods remain our unrestricted property until full payment (no right of disposal or processing). - Warranty: Exclusive sale to commercial businesses (§ 14 BGB). For used and IIa goods, there is an exclusion of liability for material defects. For new goods, the respective manufacturer's warranties apply.

Condition: excellent (used), Year of construction: 2024, operating hours: 667 h, lifting height: 3,400 mm, fuel type: diesel, mast type: triplex, power: 37 kW (50.31 HP), motor manufacturer: Kubota, fork length: 1,200 mm, total height: 1,990 mm, total length: 3,150 mm, total width: 1,480 mm, color: other, Empty weight: 4.438 kg Engine type: Kubota D1803 CRT E5B Lifting capacity: 3.000 kg CE mark: yes Technical condition: very good Visual appearance: very good Hsdpfx Aszuyrajchenr = Additional options and accessories = - 3rd hydr. circuit - Pallet forks - Side shift - Work lamp(s) = Remarks = Drivetrain Stage / Tier: Stage V / Tier V General Country of production: Frankrijk

Condition: used, Condux Granulator type CS 300/600-4 WK Rotor diameter: 300 mm Rotor width: 600 mm Hjdpozuyq Njfx Achsnr Rotor knives: 3 Housing with 4 stator knives Drive motor 11 kW (on request max. 30 kW)

Condition: refurbished (used), functionality: fully functional, Year of construction: 2002, operating hours: 7,100 h, load capacity: 16,000 kg, lifting height: 3,100 mm, load center: 600 mm, fuel type: gas, mast type: duplex, construction height: 3,050 mm, fork length: 2,400 mm, color: blue, Equipment: CE marking, UVV, cabin, sideshift, We are selling a Rudolf Maxein compact forklift with the following specifications at a net price of €59,000.00: Rudolf Maxein - KSB 160G compact forklift with internal combustion engine Buy a used reach truck from MABO Forklift Service GmbH Accessories: 3rd and 4th auxiliary hydraulics Hnedpfxjzuyq Aj Achor Joystick control Fork adjustment 2 x work lights at the front 1 x reversing light at the rear Comfortable driver's seat Single-pedal operation

Condition: used, Factory-reconditioned edge processing line for 3 mm edges Manufacturer: IMA Type: Combima Consisting of: Machine 1: Used edge processing machine from IMA, type COMBIMA Factory-reconditioned with a 12-month warranty - Working width max. 1,500 mm, edge thickness approx. 0.3 - 3 mm - Rolling needle bearing chain, drive with 3 kW motor, steplessly adjustable from 9 - 45 m/min - Motorized width adjustment with electronic setpoint and actual value display - Double trimming unit with 2 motors, 4.4 kW, 100 Hz - Milling unit with 1 motor, 4.4 kW, 100 Hz - Hot melt adhesive unit with 2-roller magazine and automatic Quickmelt hot melt adhesive feed - Trimming unit with 2 motors, 0.4 kW - Pre-milling and flush milling unit with 2 motors, 1.5 kW - Chamfering unit with 2 motors, 0.6 kW - Profile drawing blade unit - Straight drawing blade unit - Edge sanding/buffing unit - Beckhoff control system with screen - Electronic converter 100 Hz, manufacturer: KEB - Electronic converter 200 Hz, manufacturer: KEB - 1 used rotating device for changing from longitudinal to transverse - Factory-reconditioned with a 12-month warranty - Max. panel length 2,500 mm, max. panel width 1,500 mm Machine 2: Used edge processing machine, manufacturer: IMA, type COMBIMA Factory-reconditioned with a 12-month warranty - Working width max. 3,000 mm, edge thickness approx. 0.3 - 3 mm - Rolling needle bearing chain, drive with 3 kW motor, steplessly adjustable from 9 - 45 m/min Hnedpfx Acezuyqvehsr - Motorized width adjustment with electronic setpoint and actual value display - Protective milling unit with motor 3.3 kW, 100 Hz - Double trimming unit with 2 motors, 4.4 kW, 100 Hz - Enclosed gluing unit with double roller magazine and automatic Quickmelt hot melt adhesive feed - Trimming unit with 2 motors, 0.4 kW - Pre-milling and flush milling unit with 1 upper and 1 lower motor, 0.4 kW - Chamfering unit with 2 motors, 0.4 kW - Copy milling unit with 2 motors, 150 W - For milling off strip overhangs on front and rear lower workpiece profiles, copy milling unit with 2 motors, 150 W - For milling off strip overhangs on front and rear upper workpiece profiles, profile drawing blade unit - Straight drawing blade - Buffing unit - Center support - Pull-out rollers 800 mm - Beckhoff control system with screen - Electronic converter 100 Hz, manufacturer: KEB - Electronic converter 200 Hz, manufacturer: KEB Delivery time after order placement approx. 4-6 months (depending on current workload and scope of desired work). Individual machine configurations are possible according to customer requirements, as the machines are disassembled down to the base frames and reassembled after replacing all wear parts.

Condition: used, Year of construction: 2010, - Release agent application, top and bottom - Scoring saw with 2.2 kW motor - Trimming unit with 8.0 kW motor - Double milling unit with 2 motors, each 4.5 kW - Gluing unit - End trimming unit - Flush trimming unit - Multi-function unit - Multi-profile edge trimming unit - Spray nozzles, top and bottom - Flat edge trimming unit - Buffing unit - Grooving unit Double-sided edge banding machine Manufacturer: IMA Type: Combima/II/390/B/L12 Year of manufacture: 2010 For longitudinal and transverse feed - 2 low-maintenance precision roller chains with 75 mm wide and 85 mm long, rubber-coated chain plates, with cams - Spacing 1080 mm. Pneumatically adjustable to heights of 8, 16 or 24 mm. ICOS OPEN control system - Max. feed width 3,300 mm - Program-controlled master + slave width adjustment - Fixed stop on the left in feed direction Workpiece dimensions - Min. feed width 244 mm (for longitudinal processing) - Max. workpiece width (chain extension) 1,300 mm - Min. workpiece thickness 8 mm - Max. workpiece thickness 45 mm (with copying function) / 60 mm (without copying) Hnodpfezuyqisx Acher Edge material: - Min. height 14 mm, max. height 65 mm - Roll material min. thickness 0.3 mm, max. thickness 3 mm Strips and edgebanding: - Min. thickness 0.8 mm, max. thickness 12 mm Feed speed - 10 - 50 m/min. with frequency-controlled drive. Infeed device - with 5 top-mounted, inclined and driven rollers. Center support with roller track - automatically lowerable and automatically centering. Equipped on each side with: Release agent application, top and bottom Scoring saw with 2.2 kW motor, 100 Hz, 6,000 RPM, pneumatically controlled. - Electronic positioning for stepless horizontal adjustment. - Vertical adjustment manually with mechanical display. Trimming unit with 8.0 kW motor, 100 Hz, 6,000 RPM. - Electronic positioning for stepless horizontal adjustment. Double milling unit with 2 motors, each 4.5 kW, 150 Hz, 9,000 RPM. - Electronic positioning for stepless horizontal adjustment. - Vertical adjustment manually with mechanical display. Gluing unit for hot melt adhesive - With single roll/edgebanding magazine for roll material up to 3 mm and edgebanding up to 12 mm - 2-fold roll magazine for roll materials up to 3 mm (can be attached to the single roll magazine) - Horizontal roll holder End trimming unit - Mounted on the upper pressure beam, with 2 motors, each 660 W, 200 Hz - Pneumatic swivel 0 + 25 for straight and miter cuts. - Automatic adjustment for miter cuts with two different edge thicknesses (e.g. 0.4 and 1.2 mm) and for "edge overhang" for copying with edge thickness 1.0 - 3.0 mm. Automatic adjustment to the feed speed 20+30 m/min. Flush trimming unit 08.0555 - With 2 motors 1,850 W, 200 Hz, 12,000 RPM. Multi-function unit 08.353 - NC controlled with 2 motors, with automatic tooling for 4 profiles. Multi-profile edge trimming unit - with automatic tooling for 4 profiles via fixed-point control Spray nozzles, top and bottom - for applying cleaning agents Flat edge trimming unit Buffing unit - With 2 motors, each 180 W, 50 Hz, 1400 RPM. 1 Grooving unit - With 4.5 kW motor, 150 Hz, 9,000 RPM. - Horizontal and vertical adjustment manually with mechanical digital display - Pneumatic activation control - Manual swivel 90 ICOS open - PC-based control system with integrated PLC and electronic path control. - User-friendly interface with Windows standards - Simple, component-oriented

Condition: ready for operation (used), Year of construction: 1997, operating hours: 34,000 h, travel distance X-axis: 570 mm, travel distance Z-axis: 2,000 mm, number of axes: 2, Horizontal turning machine manufactured in 1997. This BOEHRINGER DUC 560/2000 features a maximum turning diameter of 570 mm and a turning length of 2000 mm. It includes an 8-position disc turret and a three-jaw chuck with a diameter of 200 mm. If you are looking to get high-quality turning capabilities, consider the BOEHRINGER DUC 560/2000 machine we have for sale. Contact us for further details. Hodpfozuyqcex Achonr - Main Drive: 19 kW- Machine Control: NUM / Keller/Plus (IBM Monitor setup)- Maximum Torque Duty Cycle: 60% / 100%- Torque: 1800 / 1400 Nm- Max Rapid Traverse (Longitudinal/Cross): 10 / 5 m/min- Tool Turret: 8-position disc turret, Sauter VDI 30- Chuck: Forkardt three-jaw chuck installed, diameter 200 mm- Included Accessories: Steady rest- Operational Status: Out of service since mid-2023 due to operator retirement- Operating Hours: Approx. 34,000 hours (single-shift operation/power-on time) Technical Specification Counter Spindle No Driven Tools No

Condition: used, Year of construction: 2008, - with workpiece return - Edge thickness max: 20 mm - Board thickness: 8-60 mm - Feed rate max: 20 m/min - with groove milling unit One: Edge banding machine with return Manufacturer: Brandt Type: KDF 991 Year of manufacture: 2008 Workpiece return Manufacturer: Ligmatech Type: ZHR 05 Boomerang Year of manufacture: 2007 Technical data - Right-hand machine - Machine length: 8,260 mm - Ligmatech ZHR 05 length: 10,460 mm - Edge thickness max: 20 mm - Board thickness: 8-60 mm - Thickness of wound edge max: 3 mm - Workpiece width min: 60 mm - Feed rate max: 20 m/min - Stepless feed: material pressure zone adjustable via servomotor - Electromotive height adjustment - Infeed stop: adjustable via servomotor - Infeed stop for thin elements - Glue system for granules: glue pot above the feed chain - BRANDT glue system QUICKMELT QA 45 - Suitable for PUR adhesives - Magazine for single strips - Spray device, front, cleaning at the rear - Pre-milling unit - Preheating zone - End trimmers: 2 motors, pneumatically adjustable - Flush trimming: top + bottom, manually adjustable - Fine milling trimming unit: 2 motors, adjustable via servomotor R2 - Edge rounding unit: 4 motors, manually adjustable - Groove milling unit: manually adjustable with tilting function - Radius trimming blades: R2, pneumatically adjustable / Second set for R1 included - Flat trimming unit - Glue joint trimming blade - Cleaning fluid spray at the rear - Buffing unit - Solid wood edge sanding unit Hnjdpfjzuyp Sjx Achsr - Conformity marking: Including complete documentation and CE

Condition: used, Year of construction: 2010, - Application of release agent, top/bottom - Joint milling unit - Gluing unit - Trimming unit - Copy milling unit SKF-L - Profile trimming blade unit - Spray cleaning agent - Self-adjusting trimming blade unit - Buffing unit Single-sided edge banding machine Manufacturer: IMA Type: Advantage 310 Year of construction: 2010 Technical data Workpiece - Workpiece length: min. 150 mm - Workpiece width: min. 65* / 150 mm *at a max. workpiece thickness of 25 mm - Workpiece thickness: min. 8 mm, 12 mm with profile trimming blades max. 40 mm (with MFA 08.346), 60 mm (with SKF) - Smallest workpiece: 65 x 300 / 150 x 150 x 19 mm - Machining allowance per workpiece edge: 0 - 5 mm (observe max. chip cross-section) - Workpiece shape: right-angled - Material: chipboard, MDF - Surface material: direct coating (melamine resin paper), paper, film, veneer Edge material - Roll material without film: Paper edges & plastic edges: 0.3 - 3.0 mm Veneer edges: 0.5 - 3.0 mm - max. edge cross-section: 150 - 180 mm² - Cut edge strips: Hedpfx Aezuyp Eechsnr Strips: 3.0 - 8.0 mm - max. strip cross-section: 520 mm² - Edge height: min. 12 mm, max. 65 mm - max. upper edge overhang: 2 mm - Edge profiles Paper edge: approx. 0.4 mm, chamfer 15 Plastic edge up to 3.0 mm, radius depending on the tool Strip up to 8 mm flush milling (with interchangeable motor on MFA) Machine - Constant workpiece projection from the chain track: 35 mm + edge thickness - max. trimming cross-section 520 mm² - Throughput width: min. 65 mm (with projection of 35 mm) - min. workpiece length in feed direction: 150 mm - Overall height (top edge of chain track): 940 mm - Unit side: on the left in feed direction - Pneumatic connection: approx. 7 - 8 bar Application of release agent, top/bottom Joint milling unit 08.379 and blowing nozzle - with 2 motors, each 4 kW, 9000 RPM, 150 Hz Gluing unit 283.1513 with oil bath gearbox - Adhesive output 0.8 l, 60 mm high, with quick-lock system - can be used for hot melt adhesive or PU adhesive - with single roll / strip magazine, roll diameter 800 mm - with 3 main pressure rollers and 3 counter pressure rollers Trimming unit 08.415 - pneumatically swiveling to 0 or 8 degrees - with 2 motors 660 kW, 400 V, 200 Hz, 12000 RPM - 2 HM trimming saw blades 160 x 3.5 x 22, Z=36 Copy milling unit SKF-L - with 2 motors 180 W, 400 V, 200 Hz, 12000 RPM - and 2 motors 400 W, 400 V, 200 Hz, 12000 RPM - 1 set of DP profile milling cutter I 80x12xHSK25-R, Z = 4, with HSK25 shank - Profile length in the feed direction: max. approx. 50 mm - Workpiece thickness: max. 60 mm - Working speed: max. approx. 20 m/min - Distance between 2 workpieces: min. approx. 400 mm - min. workpiece projection = 35 mm + profile depth Profile trimming blade unit 08.519 - For finishing a top and bottom milled quarter-circle profile Spray cleaning agent Self-adjusting trimming blade unit 08.521 - for removing hot melt adhesive residue from the edge area of the top and bottom of the workpiece Buffing unit 08.617-2 - with an upper and lower motor: 180 W, 50 Hz, 1400 RPM - 2 polishing pads 50 x 160 x 19 mm

Condition: used, Year of construction: 1996, - Double-sided IMA COMBIMA for longitudinal machining - Swiveling device - Double-sided IMA COMBIMA for transverse machining 1 used edge processing line IMA COMBIMA / K/ II/ R75 / 1075 / V / R3 Year of manufacture: 1996 Consisting of: - Double-sided IMA COMBIMA for longitudinal machining: Double edging unit 2 x milling units Gluing unit with granular pre-melting device 6-position roller magazine for edge material 1 x main pressure roller and 4 x follow-up pressure rollers Cutting unit Flush trimming 2 x fine milling units Profile trimming blade Surface trimming blade Buffing unit Smoothing unit - Swiveling device from longitudinal to transverse - Double-sided IMA COMBIMA for transverse machining Hnjdszuypxepfx Achor Protective milling Double edging Grooving milling unit Gluing unit with granular pre-melting device 6-position roller magazine for edge material 1 x main pressure roller and 4 x follow-up pressure rollers Capping at the top pressure (retrofit to current model) Flush trimming Fine milling 2 x MFA milling units Grooving milling unit Profile trimming blade Surface trimming blade Copy buffing (4 motors) Buffing (2 motors) Smoothing unit Note: The technical data and descriptions are a transcript of the order confirmation at the time. Data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2009, - Edge material thickness: 0.3 - 3.0 mm - Paper, PVC, and ABS edge bands: 0.3 - 3.0 mm - Veneer: 0.5 mm - 3.0 mm - Wood strips: 0.8 - 20 mm - Edge height: 14 mm - 65 mm Single-sided edge banding machine Manufacturer: IMA Type: Novimat Contour/I/G80/790/L20 Year of manufacture: 2009 Technical data - Electronically controlled feed speed: 6-30 m/min - Edge material thickness: 0.3 - 3.0 mm - Paper, PVC, and ABS edge bands: 0.3 - 3.0 mm - Veneer: 0.5 mm - 3.0 mm - Wood strips: 0.8 - 20 mm - Edge height: 14 mm - 65 mm - Maximum edge overhang from above: up to 8 mm edge thickness - 5 mm, over 8 mm - 2 mm Workpiece size: - Minimum workpiece length in the feed direction: 150 mm - Minimum workpiece width: 25 mm, thickness: 65 mm - Minimum workpiece thickness: 8 mm (without profile trimming blades) or 12 mm with profile trimming blades - Maximum workpiece thickness: without corner copying, max. 60 mm (max. 40 mm with corner copying) - Smallest element: 150 mm x 150 mm or 65 mm x 300 mm Note: *65 mm with a maximum piece thickness of 25 mm The edge banding machine is equipped with: - Hand-adjustable guide rail for inserting workpieces - Trimming units 08.376, 2 motors, each with 4.5 kW, spindle speed 9000 rpm, 150 Hz Hnedpfx Acezuypreher - Heating unit for warming the workpieces - Gluing unit with drive 283.1513, featuring a tightly sealed oil pan, drive arranged with glue pot content of 0.8 l and glue application height of 60 mm, with a pneumatic quick-clamping system for hot melt and PU adhesives, magazine for edge banding rollers and strips, edge banding roller diameter 800 mm - Glue pellet preheating unit with automatic feeding of glue pellets from a 30 kg container. - Automatic preheating unit for PU cartridges with a weight of approx. 2.5 kg and a capacity of 8-10 kg/h - Trimming unit 08.42/30/B, pneumatic adjustment of the saw blades from 0 - 25°, 2 motors 660 W, 200 Hz with frequency inverter and braking function - Pre-milling unit 08.055, swiveling up to max. 30° - Multi-chamfering unit 08.342, 2 motors, 660 W, 400 V, 200 Hz, 12000 1/min - Cleaning agent dispenser - Profile trimming blades 08.519 - Surface trimming blade 08.521 for removing excess glue from glue joints - Buffing unit 08.617-2, 2 motors with 180 kW, 50 Hz, 1400 rpm - Groove/milling unit with one motor Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2005, - Automatic infeed table - KFA unit - Return system Used single-sided edge banding machine Manufacturer: IMA Type: Combima Systems / I/R751220/R3 1 single-sided combination machine for trimming, edge gluing and edge finishing of panel-shaped workpieces made of wood and/or wood-based materials. - Automatic infeed table - KFA unit - Return system Technical data "Workpiece": Workpiece length - min.: 238 mm - max.: 2350 mm Workpiece width - min.: 142 mm - max.: 800 mm Workpiece thickness: - min.: 8 - 40 mm Technical data "Strip" (only for longitudinal processing): Roll material: - Paper edge bands & plastic edge bands: 0.3 - 3.0 mm - Veneer edge bands: 0.5 - 3.0 mm Hsdjzuyplepfx Achjnr Edge height: - min.: 14 mm - max.: 45 mm Technical data "Machine": Variable workpiece overhang from the chain conveyor (including edge with edge thickness 0.3-3 mm): - min.: 40 mm - max.: 80 mm - PC control ICOS open - Feed speed v=5-25 m/min, frequency-controlled drive - Inclined roller table as infeed section NC infeed system for front and carcass parts - for length and width-independent automatic workpiece feed in single-sided edge processing machines. Only for the production of strip material in the 2nd pass - An additional stop rail, adjustable via NC axis. Double milling unit 08.376: - Controllable - Motor 1 operating in the same direction and motor 2 operating in the opposite direction - Reserve space on the unit carrier for a double trimming unit with electrical pre-installation for 2 x 6.6 kW. - Heater 300 lg, 2x1.5 kW, for preheating the workpiece edge. - Gluing unit 04.1570 system for straight edges and adhesive application to the workpiece. The edge thickness depends on the magazine used and is max. 3 mm. - Adhesive application for workpiece thickness max. 50 mm - 2 pre-melting tanks for PU adhesive - 12-position edge magazine for roll material 0.3-3 mm thick. (8 slots up to 3 mm, 4 slots up to 1.3 mm) Vertical roll holder for 12 rolls: - max. roll diameter 850 mm - max. edge height 45 mm - Trimming unit 08.42, for 2 motors mounted on the upper pressure bar - Pre-milling and milling unit with height sensor - with 1 motor 1000 W - Multi-profile / chamfer unit, with 2 motors 1000 W - Contour milling unit KFA 30 - Multi-profile drawing blade unit - Flat drawing blade 08.517 - Copy edging unit 08.604 - Edging unit 08.617-2 - Double milling stand 75.184, 1050 mm high, both stand sides can be used - Milling / profile milling / grooving unit 75.34 with 1 motor, without tool, 100 Hz, 6000 rpm - Milling / profile milling / grooving unit 75.34 with 1 motor, without tool, 100 Hz, 600 rpm - Motor spindle for the use of the Hydro-Format tool system - Return system, manufacturer Meinert Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: excellent (used), axle configuration: 3 axles, permissible axle load (axle 1): 9,000 kg, permissible axle load (axle 2): 9,000 kg, permissible axle load (axle 3): 9,000 kg, first registration: 06/2014, loading space length: 13,670 mm, loading space width: 2,490 mm, loading space height: 2,800 mm, total length: 13,860 mm, total width: 2,550 mm, total height: 4,000 mm, suspension: air, tire size: 385/55 R22.5, wheelbase: 8,960 mm, color: other, Year of construction: 2014, = Additional options and accessories = - Lifting Roof - Toolbox = Remarks = Superstructure Fifth wheel height: 100 cm Krone Coilliner Coil floor Aluminum side panels Hydraulic lifting roof Sunroof Disc brakes Groove holes in coil floor and side beams Perfect condition = More information = Axle configuration Tyre size: 385/55 R22.5 Brakes: disc brakes Suspension: air suspension Rear axle 1: Max. axle load: 9000 kg; Tyre profile left: 60%; Tyre profile right: 60% Rear axle 2: Max. axle load: 9000 kg; Tyre profile left: 60%; Tyre profile right: 60% Rear axle 3: Max. axle load: 9000 kg; Tyre profile left: 40%; Tyre profile right: 40% Weights Empty weight: 8.650 kg Carrying capacity: 32.350 kg GVW: 41.000 kg Maintenance, history and condition APK (MOT): tested until 06/2027 Technical condition: very good Visual appearance: very good Identification Registration number: ON-24-JJ = Dealer information = For more photos see: Why you buy from Thomas Trucks? That choice is simple. Thomas Trucks is one of the independent trading companies worldwide in the field of used commercial vehicles. Here you can choose from an ever-changing stock of second hand trucks, tractors, trailers and trailers. Our offer includes all European brands, construction years and price ranges. Here you will always find a good vehicle for the right price! Thomas Trucks always has: - Sharp prices - Good service - Spacious, rapidly changing stock Hjdjzuypfopfx Achenr - Known quality - Decent business - We speak many languages - Accompaniment input and transport - (Export) license plate quickly arranged - Professional technical services - And more. Visit the website: and view our complete range and competitive offers We are open 6 days a week. Do you need help with exporting, importing, or shipping your vehicle? Contact our sales team. Selling your current vehicle to us is also possible. We do our best to display the data as accurately as possible, however no rights can be derived from this data We can also arrange financing for you within the Netherlands.

Condition: new, mileage: 5 km, power: 397 kW (539.77 HP), first registration: 05/2026, fuel type: diesel, axle configuration: 4x2, fuel: diesel, brakes: retarder, color: black, driver cabin: sleeper cab, gearing type: automatic, emission class: euro6, Year of construction: 2026, Equipment: AdBlue, retarder, Volvo FH13.540 Aero Globetrotter XL 4x2 - New - Full specification - Retarder - I-ParkCool - Full air suspension Model Year: 2026 - New Mileage: 680 km New truck Full specification Retarder I-ParkCool - Night climate control Full air suspension Camera 2x fuel tank Batteries in the rear = Further information = Hsdpfx Aszuyn Uechenr Transmission: I-Shift, automatic Front axle: Steerable Rear axle: Double tires Number of cylinders: 6 GVWR: 18,000 kg Overall condition: very good Technical condition: very good Optical condition: very good

Condition: used, Year of construction: 2014, Drilling and dowel insertion machine Manufacturer: Weeke Type: OPTIMAT ABD150 Year of manufacture: 2014 Technical data Hnodpfx Aezuyn Ischor Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 1985, Folding system Note: The system has been refurbished and received a new control system in 2013! Folding system consisting of: Lifting table with pusher Roller conveyor Infeed Transfer system and workpiece pre-cleaning Double-end profiler Manufacturer: Homag Type: FG63 Year of manufacture: 1985 Technical data - with adhesive strip application - Machine for profiling and folding the edge strips Hnedpfxezuynzo Acher - Milling station on both sides - Control system: Siemens Simatic Touch - Glue application unit - Folding unit for folding the pre-folded workpieces - Sliding shoe for pressing - Extraction table for material removal Electric scissor lift table Manufacturer: Altek Year of manufacture: 2014 Technical data - Load capacity max. 1000 kg - with attached roller conveyor - Dimensions approx. 3100 x 1000 mm - with height measuring device for automatic detection of stack height and corresponding cycle time Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 1988, Slot drilling machine Hedpfjzuynujx Achsnr Manufacturer: SCM Type: AS 16 Year of manufacture: approx. 1988

Condition: used, Year of construction: 1987, Twin saw Manufacturer: Hüllhorst Type: DH5 4SR Year of manufacture: 1987 Hnsdpfx Acszuynneher Technical data Working width: 2500 mm Length of support arms: 3350 mm with 2 x scoring saws and 2 x main saws Note: The technical data and descriptions are a copy of the original order confirmation from that time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2019, - Magazine loading system - Clamping table for frame parts - 3 horizontal, longitudinal drilling units from the rear - 4 vertical drilling units from above 1 Drilling machine Manufacturer: KOCH Type: BL 2500 NC select line - used - Year of manufacture: 2019 Workpiece dimensions Workpiece length 150 - 2500 mm Workpiece width 20 - 300 mm Workpiece thickness 10 - 50 mm Material: Solid wood Magazine loading system 1 with workpiece return. Workpiece insertion via 2 parallel-controlled servomotors. The number of workpieces in the magazine depends on the workpiece weight. Manual workpiece insertion Clamping table for frame parts 1 By inserting 3 support segments into the longitudinal drilling units, workpieces can be inserted manually and clamped with clamping cylinders and templates. This also allows for special workpiece dimensions. Work cycle triggering via 2 manual controls on the swappable control panel. 3 horizontal, longitudinal drilling units from the rear Construction width 160 mm Drilling motor 2 kW Longitudinal adjustment (X) with LCD display Vertical adjustment (Z) With dust extraction 4 vertical drilling units from above (supported on one side in a linear guide) Adjustable over the entire working width (X), reading LCD display. Adjustable in working depth (Y), reading LCD display Hnsdjzuynhepfx Achsr One vertical clamping cylinder mounted directly on the unit Counterpieces for through-holes are available as an option. Drilling motor 1.5 kW at 50 Hz Drilling stroke 50 mm Speed 2,800 rpm Total drill length 70 mm With 4 rotary indexing heads with quick adjustment (for vertical drilling units) with fixed stops at 0 and 90 degrees Positioning control KOCH NUMERIC Basic 1 Positioning control with Beckhoff C6920 industrial PC Intel Celeron 2.2GHz CPU 2.5 320GB HDD 1x RS232, 2x USB, 1x Ethernet available 15-inch touch panel Operating system Windows 7: English User interface in English Input of all machine commands via the touch panel Software is prepared for an online connection. The configuration of the online connection (network) and commissioning are carried out by the customer or their software company. USB port on the PC 4 x Dynamic NC axis (with bearing control) for Z axes Connection data 1 Electrical connection 400 V, 50 Hz, 3 phases Voltage fluctuations max. + 6 % to - 10 % If protected by an RCD (residual current device) on the customer's side, an all-current sensitive (R CCB, Type B) RCD with a rated residual current of /= 300 mA must be used. Air connection 7 bar Dust extraction air velocity min. 30 m/s Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1988, Panel saw Manufacturer: Rapid Hodjzuynbjpfx Achenr Model: PK 100 Year of manufacture: 1988 Note: The technical data and descriptions are copies of the original order confirmation from that time. The information is provided for informational purposes only and is not binding.