Injection moulding machines up to 5000 KN

Arburg Arburg 520V 1600-70, 2023 (Servo)

Condition: excellent (used), Year of construction: 2021, operating hours: 14,600 h, functionality: fully functional, machine/vehicle number: 248760, clamping force: 40,000 kN, screw diameter: 70 mm, displacement volume: 1,212 cm³, injection pressure: 1,650 bar, injection weight: 1,030 g, mold height (min.): 450 mm, ejector force: 9,64,000 N, ejector stroke: 250 mm, opening stroke: 1,000 mm, plate length: 1,450 mm, plate width: 1,200 mm, plate height: 1,100 mm, installation height: 3,650 mm, total length: 7,740 mm, total width: 2,340 mm, total height: 2,300 mm, overall weight: 25,600 kg, heating capacity: 29 kW (39.43 HP), pressure: 200 bar, number of injections: 1, pump power: 56,000 W, power: 118 kW (160.44 HP), type of input current: three-phase, input frequency: 50 Hz, input voltage: 400 V, input current: 213 A, Equipment: documentation/manual, The machine has few operating hours and is in very good condition, having been well-maintained. The machine comes with a Viper12 robot, which was originally supplied with it and can be seen in the accompanying photos. The robot’s control system is not integrated with the machine, so the robot can be removed and used separately, or another robot can be installed in its place. The machine has three air valves and two hydraulic valves, Euro map signals, and a signal for the dispensing unit’s rotation speed. The machine also has a strip guard, which is not included but can be arranged separately. The extruder’s heating elements are insulated with thermal insulation. Due to the guard, the machine can operate with the rear door open. It also has a water tank with 8 zones and two additional blocks with 8 outlets each. The machine has 8 zones for heating the tooling. Only PS material has been injection molded on this machine. Gsdpfx Aezqbk Nsp Dokc

Condition: good (used), Year of construction: 2004, clamping force: 800 kN, screw diameter: 35 mm, For sale is an injection molding machine by Krauss-Maffei, type 80-220C2 The machine comes from a clean operation that places great importance on maintenance and is fully operational immediately after installation Godpfx Apjwqmvge Dskc Year of manufacture: 2004 Machine number: 61004709 Clamping force 80 tons Equipment: -Cylinder D35 -1 hydraulic core pull -Pneumatic needle shut-off -Tie bar withdrawal device on the operator’s opposite side Transport and loading can be organized throughout Europe for an additional charge if desired. Prices plus VAT Inspection possible by appointment. Contact us—our team is happy to assist you. Trade-in or exchange possible! Machines buying / selling PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES ETC. Do you need a high-quality yet affordable metalworking machine for your production? Or do you want to sell yours? For further info or means of contact, visit our website

Condition: excellent (used), Year of construction: 2021, operating hours: 3,300 h, functionality: fully functional, machine/vehicle number: ADKL2001, clamping force: 14,000 kN, screw diameter: 120 mm, clearance between the columns: 1,450 mm, column diameter: 240 mm, displacement volume: 7,351 cm³, injection pressure: 1,200 bar, injection weight: 6,983 g, mold height (min.): 650 mm, ejector force: 3,50,000 N, ejector stroke: 380 mm, opening stroke: 1,450 mm, plate length: 2,950 mm, plate width: 2,000 mm, plate height: 2,000 mm, total length: 14,100 mm, total width: 3,400 mm, total height: 3,600 mm, overall weight: 75,000 kg, heating capacity: 60 kW (81.58 HP), pressure: 178 bar, number of injections: 1, pump power: 2,04,000 W, power: 266 kW (361.66 HP), type of input current: three-phase, input frequency: 50 Hz, input voltage: 400 V, input current: 520 A, Equipment: documentation/manual, The machine has seen limited use and is in very good condition. It has been well maintained. The machine only processes ABS and PP. It features a Beckhoff control system. The machine is equipped with extensive additional equipment, including 3 pneumatic valves, two hydraulic valves, a servo valve for table movement hydraulics, 32 tool heating zones, a water manifold with 8 zones, a screw heating element insulation, a hydraulic screw rotation system for torpedo replacement, a torpedo with a locking system, an interchangeable centering ring, a Euro-map for the robot, a door with automatic opening via an electric motor, and an electrical cabinet with sockets. Additionally, water blocks are installed on both the moving and stationary tables, each with 8 connections. Furthermore, a set of spare parts is included, such as a complete torpedo, a screw nozzle, heaters, temperature probes, and specific hydraulic seals, as well as a self-filtration filter and a torpedo wrench, and auxiliary ejector rods. A Wemo robot can also be sold with the machine; while it is not the subject of this advertisement, it can be purchased separately and added to the machine. It was used with the machine and is adapted for it. Gksdpfszna T Rex Ap Dec

Condition: used, Injection molding machine ARBURG, Type Allrounder 320 C 600-100 Serial No. 189356, Year of manufacture 09/2002 Clamping force 60 tons Screw diameter 25 mm Dosing volume max. 49 cm3 Injection pressure max. 1570 bar Opening stroke - platen stroke max. 350 mm Platen dimensions 446 x 446 mm Tie bar spacing 320 x 320 mm Mold height min.: 200 mm Platen spacing min.: 200 mm Platen spacing max.: 550 mm Centering of fixed and moving platens 125 mm Heater power 4.9 kW Motor power hydraulic pump 15 kW Mains connection 400 Volt, 50 Hz, 19.9 kW - Machine control SELOGICA - Two controllable hydraulic circuits for core pullers - Injection unit with COLORTRONIC material hopper for automated granule feed - U-version interface - HHG interface - Control ARBURG MULTRONICA with foil keypad and integrated display - 88790 operating hours recorded (power-on hours) - 44925 operating hours of the hydraulic pump (hydraulic on) - Control cabinet fixed to the machine - Work area protective doors at the front and rear, manually sliding with safety switches - Mobile control panel with function keys, mounted on the back of the machine Space requirement L x W 3650 x 1700 mm Height with material hopper 2200 mm Gkodozqglropfx Ap Djc Weight 3000 kg Good condition

Condition: good (used), Year of construction: 2000, Krauss Maffei KM 800-8100 injection molding machine Year of manufacture: 2000 Serial number: 8I181A5 Control system: Krauss Maffei MC4 Technical data Clamping force: 8000 kN (800 t) Screw diameter: 95 mm L/D ratio: 23:1 Injection volume: 3721 cm³ Injection weight (PS): 3386 g Injection pressure: 2172 bar Maximum cylinder temperature: 375°C Screw speed: 126 rpm Injection rate: 659 cm³/s Plasticizing rate: 112 g/s Nozzle closing force: 166 kN Clamping unit Dimensions of mounting plates: 1600 × 1530 mm Distance between columns: 1120 × 1000 mm Opening stroke: 1400 mm Minimum mold height: 600 mm Maximum mold height: 1100 mm Maximum daylight opening: 2000 mm Ejector stroke: 250 mm Ejector force: 226 / 59 kN (front / rear) Electro-hydraulic system Pump motor power: 110 kW Installed heater power: 61 kW Number of heating zones: 7 Number of dry cycles (EUROMAP): 560 cycles/h Oil tank capacity: 1500 l Motor current: 235 A Total current consumption: 455 A Main fuse: 2 × 250 A Equipment Control system: Krauss Maffei MC4 Robot interface: Euromap 12 Hydraulic cores: 4 pcs. Pneumatic valves: 4 pcs. Robot preparation: Yes Central lubrication system: Yes Oil cooling system: Yes Gkjdpszrw Adefx Ap Dsc Dimensions and weight Length: approx. 10,600 mm Width: approx. 2860 mm Height: approx. 2410 mm Weight: approx. 47,000 kg

Condition: excellent (used), Year of construction: 2010, clamping force: 600 kN, Equipment: documentation/manual, Clamping force: 60 t Gksdpfszn I H Eox Ap Djc Screw diameter: 20 mm Distance between tie bars V: 370 mm Distance between tie bars H: 370 mm Type: Horizontal Drive: Hydraulic Engine hours : 60,700 h Hydraulic circuits : 1 x Hot runners : 6 x Robot interface : NO

Condition: ready for operation (used), Year of construction: 2023, operating hours: 260 h, clamping force: 550 kN, screw diameter: 25 mm, Hydraulic injection moulding machine manufactured in 2023. This TEDERIC NEO.E55/e110h features a 12" color TFT touchscreen control unit and a stainless steel material hopper. It includes a 3-stage central ejector and a pneumatic core pull control. With a screw diameter of 25 mm and a bimetallic barrel, this machine is designed for efficient operation. If you are looking to get high-quality injection moulding capabilities, consider the TEDERIC NEO.E55/e110h machine we have for sale. Contact us for further details. General • Operating Hours: Approx. 260 h • Machine Condition: Working Injection Unit • Screw Diameter: 25 mm • Screw Type: Nitrided Thermoplastic Screw • Barrel: Bimetallic • Nozzle Radius: 10 mm • Nozzle Bore Diameter: 2.5 mm • Stainless Steel Material Hopper • Manually Sliding Material Hopper • Feed Throat Temperature Control • Dosing Signal Output • Ceramic Heater Bands • Hot Runner Controller: 8 Zones • Temperature Control Channels: 8 Clamping Unit • Centering Ring Diameter: 100 mm • Mounting Plate Threads: M16 • Euromap Standard: Euromap 2 • 3-Stage Central Ejector • Central Lubrication for Mould Height Adjustment • Pneumatic Ejector: Included Gksdpfx Aoznu Ddop Dec • Pneumatic Core Pull Control: 1 • Core Pull Connector: Euromap 13 (HAN 16A) • Water Circuits: 6 Control & Electrical • Control Unit Brand: KEBA • Display: 12" Color TFT Touchscreen • Power Supply: 400 V • Frequency: 50 Hz • Main Switch: 4P+PE Automation & Accessories • 3-Axis Linear Robot: TLRE03-650, (optional, not included) • Robot Payload: 3 kg • Pneumatic C-Axis • Mechanical Robot Interface: Euromap 18 • Electrical Robot Interface: Euromap 67 • Vacuum Circuits: 2 • Compressed Air Circuits: 2 • Automatic Lubrication of Main Axes • Robot Protection Class: IP67 • Emergency Stop: 1 • Conveyor Belt Dimensions (optional, not included): 2000 × 400 × 1100 (+100) mm • Safety Fence Dimensions (optional, not included): 800 × 1000 × 2000 mm • Spare Parts Kit with Non-Return Valve (optional, not included)

Condition: used, Year of construction: 1997, _Engel ES 1050/200 HL_ Clamping force: 200 t Year of manufacture: 1998 Control system: CC 100 Screw diameter: 45 mm Screw type: GF Min. mold height: 250 mm Max. opening stroke: 700 mm Max. platen distance: 950 mm Ejector stroke: 150 mm Tie-bar spacing (H × V): 820 × 750 mm Platen size: 500 × 570 mm Gkodpfeztadgex Ap Dec Quick clamp: Yes Extras: Software gate separation