Eccentric Press - Single Column

BEUTLER PDR 100

Condition: used, Year of construction: 1983, Technical details: pressure: 100 t stroke: 20 fest mm no. of strokes: 55 Hub/min table surface area: 900x640 mm throat: 355 mm ram adjustment: 150 mm mortise hole in ram: Ø 36 mm clamping surface ram: 500x415 mm height over floor: 800 mm biggest distance between table & ram: 390 mm passage opening in table: Ø 330mm mm total power requirement: 11 kW weight of the machine ca.: 7,5 t transport dimensions LxWxH: 1,9x1,6x3,1 m Press is without electric cabinet, optional construction of electric cabinet possible. * Guedpfx Akju Nfi Ujasg

Condition: good (used), Year of construction: 1995, functionality: fully functional, turning diameter over cross slide: 267 mm, spindle bore: 76 mm, center height: 228 mm, center width: 1,500 mm, quill stroke: 229 mm, quill diameter: 75 mm, total length: 3,030 mm, total width: 1,200 mm, total height: 2,000 mm, rotational speed (max.): 1,600 rpm, rotational speed (min.): 20 rpm, overall weight: 2,300 kg, Conventional lathe, center high 228 mm, between centers 1500 mm, bore Ø 76 mm, 16 speed 20 - 1600 rpm, motor 9,3 kw, camlock 8'', dimensions 310x120x200 cm, weight ca. 2300 kgs; equipement: pneumatic chuck SCHUNK ROTA Ø 315 mm, coolant device, 3-jaws chuck Ø 315 mm, several jaws, live center, tool post PARAT WD with toolholders, steady rest, drilling chuck, lamp, manual, cabinet Godpfx Aksypud Ueaoug

Condition: good (used), Year of construction: 1980, turning diameter over bed slide: 1,040 mm, turning diameter over top slide: 710 mm, turning length: 2,000 mm, bed width: 600 mm, Optional chuck 1200 mm 2 Axis RSF Digital read out Conical turning attachment Spindle bore 130 mm Central lubrication DBC Turning Length: 2000mm Swing over bed Ø: 1040mm Swing over cross slide Ø:710mm Swing in the gap Ø: 1780mm Gap length: 1000mm Spindle bore: 130mm Gjdpsx Tgr Tefx Akasug Bed width: 600mm Tailstock spindle Ø: 130Ø Stroke pinole: 300mm Spindle taper: 6Mk Power: 22kW Speeds / ranges: 600Rpm Feed rate X-Axis: 4000mm/min. Feed rate Z-Axis: 4000mm/min. Length: 6000mm Width: 2100mm Height: 2100mm Weight: 8300kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) Gusdpfxergzv Nj Akaeg * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: used, Year of construction: 2010, operating hours: 11,780 h, Equipment: ABS, all wheel drive, Volvo EXCAVATOR EW140C Gjdpsyltr Aefx Akaeug air conditioning 16,850 kg 91 kW Top condition

Condition: used, Year of construction: 1973, pressure 200 t chamfer lenght 3600 mm distance between columns 2650 mm dayligth 500 mm throat 300 mm stroke 250 mm working feed 10,5 mm/sec return speed 100 mm/sec ram stroke speed 150 mm/sec table height 900 mm oil volume 500 l total power requirement 37 kW weight of the machine ca. 17800 kg dimensions of the machine ca. 3710 x 1800 x 3390 mm Equipment: - Controlled axes Y1 + Y2 - Manual X-axis with digital position display - Set of upper and lower tools - 2x stop fingers - 2x front support arms - Hand and foot controls - Side + rear safety guard Gjdpfx Akst I D U Eoasug - Operating instructions

Condition: good (used), Year of construction: 1995, roller (top) diameter: 330 mm, sheet thickness (max.): 23 mm, Manufacturer: IMCAR Type: SIHR Year of manufacture: 1995 Extended end for profile bending rolls (Pipe & T-Angle) Central lubrication Digital readout position side rolls Fully hydraulic machine Hydraulic drop end Hardened rolls Specifications Metric US Standard Roll width: 3100 mm Sheet thickness at 3 x top roll Ø: 18 mm Sheet thickness at 5 x top roll Ø: 23 mm Sheet thickness for initial bending: 20 mm Top roll Ø: 330 mm Side roll Ø: 310 mm Number of rolls: 3 Bending speed: 0 - 5 Side roll adjustment: 200 mm/min. Number of driven rolls: 2 Power: 15 kW Dimensions (estimated) Length: 5250 mm Width: 1700 mm Height: 1700 mm Weight: 11900 kg Guodpfx Ajwpku Djkasg Please note: The information on this page has been provided to the best of our knowledge, and wherever possible, from the manufacturer. The information is given in good faith, but accuracy cannot be guaranteed. Accordingly, it does not constitute representation or contractual terms. We recommend you check all critical details.

Condition: excellent (used), Year of construction: 2018, Geared motor, electric motor, electric geared motor, spur geared motor -Manufacturer: SEW-Eurodrive, helical gearmotor -Type: R97/II2GD EDRN160L4/3GD/TZF/AL i18.24 -Speed: 1474/81 rpm at 50 Hz, see photo type plates -Power: 15 kW -Shaft: Ø 60 x 120 mm -Protection class: IP54 -Dimensions: 970/400/H370 mm -Weight: 231 kg Godpet Drkyefx Akasug

Condition: ready for operation (used), Year of construction: 2020, A complete low-pressure steam boiler system Viessmann is available. 1) Condensate unit Viessmann TWA-T LS 0,9, max. operating pressure: 0.1bar, test pressure: 0.2bar, max. temperature: 110°C, water volume: 400l. 2) Dosing system Schweizer-Chemie EMP 2.5l E60. 3) Steam generator Viessmann Vitoplex 100-LS, year of manufacture: 2019, nominal heat output: 460kW, steam capacity: 700kg/h, water volume: 960l, operating pressure: 1bar, test pressure: 4.8bar. 4) Control cabinet Viessmann Vitocontrol HS. 5) Steam accumulator/pressure vessel Viessmann RBS/1 1000 So. steam, volume shell space/tube space: 990l/17l, max. operating overpressure shell space/tube space: 10bar/2.5bar, max. operating temperature shell space/tube space: 95°C/130°C, test pressure shell space/tube space: 13bar/4bar. Documentation available. An on-site inspection is possible. Gjdpfxsx Uq Uuo Akaeug

Condition: new, The unit is new, complete including controls, diesel tank, exhaust and batteries. Description Model: NWR55 Ricardo Motor Newpower Generator Generator set Maximum power: 40kW / 50 kVA Engine : Kofo RIcardo N4100ZDS-42, 4 cylinder water-cooled Connection: circuit breaker Frequency : 50 Hz. Voltage: 400/230 V including mechanical speed control, AVR, battery charger, galvanized soundproofing, cooling water heater, Control unit: Comap AMF8, mains feed Dimensions: 2280x1030x1260 mm Weight: approx. 1020kg Diesel tank: 118 L. At 100% load: 8.5 L/h At 75% load : 6.5 L/h At 50% load : 4.4 L/h Network monitoring, network feed-in, soundproofed Ready for immediate use. Guodpfomgbayox Akaeg additional costs 63A automatic switch: € 500 100A automatic switch: € 620 Shipment: - Worldwide transport including unloading is possible for an extra charge - In order to be able to quote an exact freight price, please send us a request with your data and your complete address