Die cutting press

Bobst SPO 1575 EG Rebuild 2015

Year of construction: 2003, condition: ready for operation (used), Used drum dryer manufactured by SAFEM, extracted from a line of gluten-free products. Fluid: Steam Design pressure: 12 bar Iodpfx Asq Nmuwedwsal Maximum operating pressure: 9,5 bar Test pressure: 24 bar Maximum operating temperature: 192ºC Volume: 4.55 m3 Pressure x Volume: 54.6 bar x m3

Condition: used, Year of construction: 2004, functionality: fully functional, Heidelberg Dymatrix 113 CSB Pro – FULLY REFURBISHED Type of machine: Embossing and die-cutting system / automatic sheet die-cutter Machine number: 400018 Year of manufacture: 2004 Machine specifications Maximum strokes per hour: 9,000 sheets/h Length without feeder: approx. 5,190 mm Length with feeder: approx. 7,770 mm Maximum width: approx. 2,400 mm Maximum height: approx. 3,200 mm Maximum height with access window open: approx. 3,930 mm Weight without feeder: approx. 30,400 kg Weight of feeder W4: approx. 3,000 kg Internal closing frame width: 820 x 1,134 mm Iedpfx Adev T T N Hjwsal Maximum die-cutting tool size: 816 x 1,130 mm Maximum die-cutting area: 800 x 1,120 mm with gripper margin Gripper margin adjustable from: Standard 11 – 17 mm with 13 mm wood before 1st knife Option 8 – 14 mm with 10 mm wood before 1st knife Rule height: 23.8 mm Maximum pile height (feeder, incl. pallet): 2,000 mm Maximum pile height (delivery, incl. pallet): 1,700 mm Maximum pile weight (feeder): 1,000 kg Maximum pile weight (delivery): 1,000 kg Maximum rest pile height (feeder): 450 mm Maximum rest pile weight (feeder): 450 kg Maximum auxiliary pile height (delivery): 200 mm Maximum auxiliary pile weight (delivery): 200 kg Pallet sizes Feeder: max. 800 x 1,200 mm (EURO pallet) Delivery: max. 800 x 1,200 mm (EURO pallet) Maximum pallet height: 170 mm Drive and electrical supply The machine is powered by a frequency-controlled motor via a flywheel. Between the flywheel and the machine, a pneumatic clutch with spring-loaded brake is installed, which is used to engage and disengage the machine. The motor runs continuously. The control cabinet placed at the machine contains, except for a few devices, all control components for the die-cutter and feeder. Command and indicator devices are located on the machine itself, distributed across the control panels as required. Control cabinet Equipment: Power supply, main switch, fuses, motor protection, PLC control Electrical rating: 3 phase, 400 V AC, 50 Hz, 63 A Control voltage: 24 V DC; 230 V AC; 50 Hz Dimensions: 2,800 x 600 x 2,200 mm The machine is in excellent condition. A test run can be arranged at any time. Various accessories are included. Patent-protected chain guide rails from QTM have been retrofitted. Price: On request

Condition: excellent (used), functionality: fully functional, Brehmer Polygraph 39-3/4 thread sewing machine for bookbinding. Includes extensive accessories and consumables. Machine is well-maintained and in very good condition. Comes with manual and complete documentation – very rare. Electrical connection 400V/50Hz. Iaedpfx Aexa Afmjdwel

Condition: good (used), Adast Grafopress GPE letterpress machine Very good condition, ready for production, after inspection. The machine has all the safety features. Iaedpfx Asv E A U Nsdwel Export version. The equipment includes printing rollers. The device is used for die cutting, printing, creasing, numbering, etc.

Year of construction: 2006, condition: excellent (used), Bobst Autoplatine Speria 106 E STANDARD EQUIPMENT MACHINE - Centerline system for quick job changeover. - Electronic sheet travel monitoring system. - Adjustable centering at the stripping station. - Control cabinet air conditioning unit. - Bobst electronic control system C.U.B.E. (Control Unit Bobst Electronic). This microprocessor-based Bobst system allows the operator to easily manage, visualize, and monitor the machine’s various functions and components. - Main motor with frequency inverter control. FEEDER - Pile tray with handle for easy manual lateral alignment during production. - Synchronization device ensuring proper sheet arrival to the front lays when the machine is stopped. - Automatic pile lifting controlled by pressing foot. Iaedpfx Adexl Talswel - Rear pile guides (operator side and opposite operator side). - Adjustable side blowers with Centerline markings. - Suction unit. FEED TABLE - Feed table with anti-static stainless steel covering. - Feed table entrance equipped with lateral ramps. - Four front lays, pairwise adjustable, with front register control. - "Pull" guide (operator side), adjustable with Centerline markings and side register control. - Double sheet detector. - Support plates at platen station entry. - Sheet hold-down mechanism (guides sheets to front lays). - Upper frame with manual lifting device. - Upper transport system for paper, paperboard, and corrugated board. - Transport belts with lateral guides and automatic tensioning system. PLATEN - Gripper reopening device. - Centering and locking for equipment. - Locking the chase to the upper beam. - Cutting force measurement with strain gauge. 1 synthetic supporting plate. 1 upper chase: fixed bottom plate. 1 cutting plate. WASTE STRIPPING STATION - Air-cylinder-driven upper frame lifting. 1 upper pull-out frame (with crossbars and clamps). 1 lower pull-out frame. DELIVERY - Pile tray. - Front jogger. - Adjustable rear and side joggers with Centerline markings. - Braking brush. - Manual non-stop rack. AVAILABLE EXTRAS B MACHINE 1 B-1 Raised machine base C FEEDER 1 C-4 Manual non-stop device E PLATEN 1 E-5 Compensating plate 1 E-55 Micro-adjustable supporting plate centering F WASTE STRIPPING STATION 1 F-31 Quick-lock device for the upper pull-out frame

Year of construction: 1972, condition: ready for operation (used), Format: 1000x700mm, an inspection is possible. Ijdpjqzkdqefx Adwoal

Year of construction: 1998, condition: like new (used), Round pile feeder, first folding unit TD78/4-1 4 pockets, second unit TD66/4-2,4 pockets, 3 unit knife Stahl EF63 (1984), SBP 80 press delivery, no pump machine was on in house air supply Iasdpfjd Tnxlex Adwol

Condition: excellent (used), Year of construction: 2002, 1) Bobst Dynaload prefeeder year 1998 2) Bobst Flexo 160 year 2002 n. 5 colors, Vacuum transport, rubber roller Bobst CUBE 3) Bobst SPO 160 A Matic year 2002 Introduction of suction cup Iajdpfev Nywvox Adwol Center Line II Stripping station with motorized Quick Lock tool clamping Batch delivery with gripper trim extraction Bobst CUBE 4) Castaldini Breaker year 2007

Condition: new, Year of construction: 2025, HEAD AND TAIL BAND MACHINE Ijdpfxoh S Uv Es Adwjal MAGRAF KV-10 PLUS

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, punching force: 330 t, Machine for punching, embossing, waste removal, and blank separation - as is - System equipped with a high-performance sheet feeder designed for automatic NON-STOP operation Iaodpfx Adjww E Nrowjl ⦁ For fully automatic punching, creasing, and embossing with or without gripper edge ⦁ For removal of internal waste as well as lateral and rear sheet edges ⦁ For stack-like delivery of punched and waste-removed sheets with attached gripper edges or ⦁ For separation of gripper edges and subsequent stack-like delivery of the remaining sheets ⦁ With a patented gripper carriage registration system for highest registration accuracy ⦁ With a pile stacker machine enabling fully automatic interleaving sheet feed as well as NON-STOP stacking and does not require modification even for the smallest job sizes (exchange table with comb structure) ⦁ Interleaving sheet magazine with electronic level monitoring, refillable during production ⦁ With Centerline equipment ⦁ With automatic pallet change device at the delivery section Specification Maximum sheet size: 760 x 1060 mm Minimum sheet size: 350 x 400 mm Maximum punching force: 3.3 MN (330 t) Speed: 9,000 sheets/hour Processable materials: Paper min. 80 g/m² Cardboard up to 2000 g/m² Corrugated board up to 3 mm (max. sheet warp 4%) Equipment: Optical sheet register (Dyset) Automatic non-stop feeder Waste removal station Blank separation station Centerline Fully automatic pallet changing device at delivery Incl. platform Quick-lock frames at all tooling stations