Creep speed Unit FG24 16/5P4

Demag

Condition: used, Year of construction: 1994, operating hours: 36,170 h, machine/vehicle number: 50557900, power: 260 kW (353.50 HP), operating pressure: 9 bar, DEMAG air compressor including PARKER HIROSS air dryer! TECHNICAL DETAILS Air pressure: 9 bar Air flow rate: 28 m³/min Motor rated power: 260 kW MACHINE DETAILS Electrical voltage: 400 V Electrical frequency: 50 Hz Max. operating temperature: 65 °C Refrigerant: 407C 7.5 kg Operating hours: 36,170 h EQUIPMENT Air dryer PARKER HIROSS POLESTAR SMART Type: PST460 Serial number: 398037030001 Year of manufacture: 2011 Gjdpfx Aey Iapnenxsub Motor power: 6.26 kW Weight: 525 kg

Condition: good (used), Year of construction: 1990, machine/vehicle number: 5211, Offer 24289 Technical data: - max. cutting width 3060 mm - max. cutting capacity at 45 Kp/mm² 4 mm - Cutting angle 1.50 ° - Cutting gap - adjustment via adjusting screws - Number of hold-down devices 15 pcs - Stroke rate 23 to 43 /min - Front angle stop - Motorized backgauge position-controlled 15 - 850 mm - Cutting line lighting - E - foot switch - Drive 400 V / 7.5 kW Gusdpfxjt Ucgaj Anxob - Space requirement approx. W 3900 x H 1600 x D 2400 mm - Weight approx. 4.5 t

Condition: ready for operation (used), Bridge Crane 5t, Demag Bridge Crane 5t, Crane 5t, Used Machine Manufacturer: Demag Overall dimensions: 10,700 x 3,000 mm Electrical data: 400 V; 50 Hz, total current = 18 Amps Hoisting unit: Demag P35 Load capacity: 5,000 kg / 5t Rope length / lifting height: 8 m Gusdpfx Aewd Hhconxeb - Wired remote control - Crane travel motor refurbished - Trolley motor refurbished

Condition: ready for operation (used), Column Jib Crane, Swing Crane, 80 kg Crane, Used Machine Gsdpfxjv R Du Us Anxjub Load Capacity: 125 kg Column Height: 3800 mm Jib Length / Reach: 1650 mm Chain Hoist: Demag PMV5-V2F6 Load Capacity: 80 kg Electrical Data: 400 V; 0.3 kW; 1.5 A

Condition: used, Year of construction: 1993, Technical details: Godpfx Aou Rni Hjnxsub sheet width: 3050 mm plate thickness: 6,0 mm distance between columns: 3460 mm no. of strokes: min./max.: 9 / 17 Hub/min back gauge: 750 mm (motorisch) mm cutting angle: 0,5° - 3,0° ° cutting gap adjustment: manuell mm down holder: 18 Stück (hydraulisch) Stück Table dimensions: 380 x 3100 mm total connected load: 7,5 kW weight of the machine ca.: 4,56 t dimensions of machine: L: 3,64 x B: 2,55 x H: 1,58 m Equipment: With side stop L: 1000 × W: 100 × H: 60 mm and stop bar 990 mm, with 8 supports Operation via control panel and foot switch Cutting zone lighting Stroke counter Machine feet *

Condition: ready for operation (used), Column crane, jib crane, 80 kg crane, used machine Load capacity: 125/80 kg Column height: 3200 mm Guodpfswfrgajx Anxsb Jib arm length / outreach: 1700 mm Chain hoist: Demag PMV5-V2F6 Electrical data: 400 V; 0.05 kW; 1.5 A

Condition: used, Demag Ergotech 3300-840, Demag injection molding machine, used machine Manufacturer : Demag, Sumitomo Model: Ergotech 3300-840 Overall dimensions : Length x Width x Height: 6.5 x 2.0 x 2.2 meters Net weight (without oil): 13 800 kg TECHNICAL DATA (BY SCREW DIAMETER) ----- Gjdex Sqi Hjpfx Anxoub Description Unit "A" "B" "C" ----- Screw diameter: [mm] 45 50 60 L/D ratio: [-] 20 20 20 Injection pressure (at 400 °C): [bar] 2402 1946 1351 Shot volume: [cm3] 358 442 636 Shot weight (PS): [g] 320 400 570 Barrel heating power: [kW] 13.0 14.8 23.1 Installed electrical power*: [kW] 58/68 60/70 68/78 ----- * Note: Values are higher with electric screw drive (WA). INJECTION UNIT FEATURES ----- Max. dosing stroke: 225 mm Max. nozzle retraction: 470 mm Nozzle immersion depth: 40 mm (SVO) / 30 mm (SPI) Nozzle contact force: 80 kN Electric screw drive (WA): 20.5 kW Material hopper capacity: 75 liters GENERAL AND HYDRAULIC DATA ----- Hydraulic oil tank capacity: 700 liters Pump unit power: 45 / 55 kW Dry cycle (EUROMAP 6a): 1440 / 1600 h-1 Dry cycle (without nozzle movement): 1890 / 2100 h-1 Continuous noise level: 74 dB (A)

Condition: as good as new (ex-display), For sale Hoist motor used/reconditioned for a DH wire rope hoist NB! Gujdpfx Aeh Up Tbjnxob we have more than 15,000 Demag parts in stock see our website or other ads

Condition: ready for operation (used), Year of construction: 2013, operating hours: 17,577 h, clamping force: 1,600 kN, total height: 2,060 mm, This SUMITOMO SHI DEMAG IntElect 220/610-750 smart was manufactured in 2013. It's an electrical injection moulding machine known for its precision and efficiency. Ideal for those looking to enhance their production capabilities with reliable technology. Contact us for more information. Additional equipment • Sepro Robot SDR 11 Machine Benefits Technical Machine Benefits • Clamping unit: 160 / locking force: 1760 kn / opening stroke max: 495 mm / mould installation height, min: 275 mm / mould installation height, max: 585 mm • Platen distance, max: 1080 mm / mould mounting platens (h x v): 760 x 785 mm / clear column distance (h x v): 520 x 520 mm • Ejector travel: 125 mm / ejector force: 35 kn • Injection unit: 340 / screw diameter: 35 mm / l/d ratio: 20 / injection flow (ps) without accumulator: 288 cm³/s • Metering stroke: 162 mm / nozzle stroke, max: 350 mm / nozzle immersion depth (svo): 20 mm / nozzle contact pressure: 30 kn • Material hopper capacity: 35 l / injection speed, max. , standard: 300 mm/s / injection speed, max. , increased: 500 mm/s • Net weight without oil filling: 7300 kg Extra Information Electrical & Pneumatic Interfaces: Sockets: 2 x Schuko (1Ph, 230V, 10A)/ 2 x IECEE (3Ph, 400V, 16A) – switched off via main switch/ Additional Schuko socket also listed (same rating)/ Valves: 1 x Pneumatic 5/2 valve on movable platen (programmable)/ 2 x Pneumatic 5/2 valves on stationary platen (programmable)/ I/O: Gjdpfxjx D Hnmj Anxoub 3 digital inputs / 3 digital outputs (freely programmable)/ Terminal board outside control cabinet/ Air & Cooling: Central air supply and piping/ Cooling system: open cycle/ Cooling water controller: 4 circuits with temperature indication (max. 10 l/min per circuit)/ Separate water connection for cooling (mould + machine)/ Switch-off for mould cooling (time programmable)/ Machine Mechanical & Motion Features: Clamp and injection unit colours: Jet black (RAL9005): bed, pump station, lower control cabinet/ Signal white (RAL9003): clamp unit, injection unit, guards, covers, safety doors/ Mould platen layout: E-standard (similar to EUROMAP, March 1996)/ No side ejector platen/ Ejector: held in front position against spring-loaded mold ejector/ Standard mold height/ Standard closing speed/ Only active movement when safety guard is closed/ Screw: wear-resistant, nitrided barrel, standard L:D, 35 mm diameter/ Non-return valve: 3-piece ring type/ Control, Programming & Monitoring: Inputs/outputs and clamp sequence: freely programmable/ Switching programs (e.g., dry cycle, startup scrap counter, timer-controlled cooling)/ Injection process: Injection force with max injection speed: 200 mm/s/ Back pressure programmable via 6-point polygon/ Follow-up pressure switch-over based on melt pressure/ Follow-up, back pressure, metering: closed-loop control/ Feed throat temp control: closed-loop, max 90°C ±9°C/ Reduced nozzle sealing force (programmable)/ Clamp force: closed-loop control/ Active mold protection: sensor-based during closing/ Hot runner control: 5 zones integrated (2.75 kW total) Display, Software & Data: Coloured data display PDA (Process Data Acquisition): 100% control with graphical parameter recording/ Overlaid graphs for multiple cycles/ External statistical data export/

Condition: used, Year of construction: 2000, Overview This complete hot-fill bottling line for non-carbonated beverages was was put together by the last producer himself and ran smoothly right up until the end. The line is designed for processing, heating, filling, cooling, and packaging of products such as juice and similar beverages. It includes upstream thermal processing, filling, downstream cooling, and end-of-line packaging equipment. The line is still assembled and can be viewed in person at any time.  Technical data Capacity: approx. 3,500 – 6,000 bottles/hour (filling section) Formats: 0.7 L / 1.0 L / 0.5 L / 1.5 L Application: Hot filling of juice and non-carbonated beverages Configuration: Heating / pasteurization system (plate heat exchanger based) Rotary filler with 28 filling valves and 4 capping heads Cooling tunnel with 3 zones Manual depalletizing crane system Rotary bottle rinser Carton erecting and sealing system Utilities: Compressed air, electrical supply Scope of Delivery Depalletizing crane system | DEMAG | Manual layer depalletizing with air-cushion gripping system Bottle rinser | FIMER | Rotary rinser with conveyor system Filling monoblock | MAG Schymanski | BETTA 28/4 | 2000 | 28 filling valves / 4 capping heads, hot fill Cooling system | 3-zone cooling tunnel with spray system Plate heat exchanger | GEA | Integrated cooling circuit Feed tank | Speidel | Atmospheric tank Pasteurization system | API Schmidt-Bretten | Plate heat exchanger based heating system Carton erecting system | BORTOLINKEMO | F.O.C. 23/30 | 1993 | Automatic carton forming unit Carton sealing system | BORTOLIN |  Hot melt carton sealing Glue system | Nordson | Series 3400 | Hot melt unit Conveyor systems | Various transport conveyors Guedpjy Rmfbjfx Anxsb

Condition: used, Year of construction: 1990, sheet width 3050 mm plate thickness 12 mm distance between columns 3100 mm table height over floor 900 mm cutting angle adjustment 0,5 - 3 ° no. of strokes 6 - 13 Hub/min back stop - adjustable 1000 mm down holder 18 St oil volume 350 l total power requirement 22,5 kW weight of the machine ca. 8 t dimensions of machine L x W x H 3,96 x 2,10 x 2,22 m - with adjustment of cutting gap - Guodju Uu Smspfx Anxeb Accessories: electr. back gauge, spare knives

Condition: excellent (used), Year of construction: 2015, Equipment: documentation/manual, Clamping force: 100 t Opening max: 500 mm Mould heigh: 250 mm Platen size: 590x600mm Distance between tie bars V: 420 mm Distance between tie bars H: 420 mm Type: Horizontal Drive: Hydraulic Gjdpfx Aeyg Eu Senxjub Screw diameter: 30 mm Injection weight: 103 g Injection volume: 115 cm3 Injection pressure: 2755 Hours: 42493 extra equipment: 1. 2 hydraulic core pull circuits on moving platen (proportional valves) 2. Additional connections for 2 core pulls on fixed platen 3. Pneumatic core pull (2 circuits) on moving platen 4. 4-zone cooling water flow controller with temperature display 5. Compressed air blow valves on fixed and moving platens (programmable) 6. Integrated hot runner control, 8 zones 7. Interfaces for external nozzle heating bands 8. Interface for integrated temperature control units (up to 6 circuits) 9. Interface for mould temperature monitoring (2 circuits) 10. EUROMAP 67 for automation equipment

Condition: good (used), 1. DEMAG drum brake Type: TH806/60 - RT315 TH806 1 piece available. 2. ELDRO electrohydraulic lifting device Ed 1250/60 Guedpeu Uvmfsfx Anxeb

Condition: used, Valves, gate-valves, butterfly-valves, ball-valves, security-valves Guedpfx Anstunb Aoxob

Condition: used, Year of construction: 2003, (1) Injection molding machine, Handling: Sepro Robotique | Success 7 | 2016 Temperature control: HB Therm | Miscellaneous: 1x Protective Enclosure 1x Conveyor Belt, company RAU Maschinenbau 1x Hot Runner Controller 1x Conveyor Belt, company SAS Grillet 1x Conveyor Unit, company Motan Technical Details: Machine size: 500/370-200 Guedpfx Ajy N R U Rjnxob Power supply: 3/N/PE AC 400 V Frequency (Hz): 50 Current (A): 94 Weight (t): 3.3 Pressure (bar): 210 Flow rate (l/min): 130