For TCT bandsaw blades sharpening

Forestone 2

Condition: used, SPE Renergi Low Temperature Dryer. Njdpfx Akewp Rqfjfswf The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Year of construction: 2026, condition: new, functionality: fully functional, Complete plastics recycling line for films and fibre materials from Taiwan leading Plastics Recycling Machinery manufacturer. GENIUS Machinery Co who have more than 30 years of recycling extruder production and experience. Extruder can be fed without size reduction or shredding.. Materials in baled, loose or reel form can be fed. Line can be supplied complete with Belt conveyor, Cutter compactor, Main extruder, Filtration system, (variety of types to suit requirements), Hot pellet die-face cutting device, Centrifugal pellet dryer, Vibrating screener, Storage silo for pellets. Additional ancillary equipment can be supplied . A two stage " Cascade" version is also available for heavily printed films, or very dirty films requiring double filtration. Alternative sizes from 100 kgs per hr up to 1200 kgs per hr can be offered. Full sales and support and training is available in UK and Europe for these extremely modern and economic machines. Nwedpowg R Rtjfx Akfsf

Condition: new, Year of construction: 2025, Entry-level sheet fiber laser metal cutting machine Lower laser cutting cost and easy operation The modular cutting machine table with stiffeners saves time for disassambly and improves convenience and rigidity. The special fiber laser nozzle and cutting process ensure faster carbon steel oxygen cutting, more gas-saving low-pressure stainless steel nitrogen cutting, and better-quality carbon steel air cutting. Fiber laser heads are able to detect jutting obstacles to effectively reduce the damage rate and save the maintenance cost of a laser cutter. Applicable Material: metal Njdohwrgtjpfx Akfjwf Condition: New Laser Type: Fiber Laser Laser Power: 1000W, 1500W, 2000W, 3000W Cutting Area: 3000*1524mm Positioning accuracy: ±0.05mm Repositioning accuracy: ±0.03mm Cutting Speed: 0-100m/min Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT CNC or Not: Yes Cooling Mode: WATER COOLING

Condition: used, Year of construction: 2026, operating hours: 15 h, functionality: fully functional, machine/vehicle number: 204065, Used machine CNC cutter/plotter Cutting area in X and Y: 3,500 x 2,100 mm. Multifunctional CAM cutting system in CNC knife technology for 2D cutting of leather, fabric, technical textiles, foam and other flat, semi-flexible or rigid, non-metallic materials Equipment of the used machine • 1 cutting bridge and 1 multifunctional tool head The machine is sold with one driven circular knife, electric oscillating knife and one Milling Head + exhaust • Multifunctional tool head to hold max. 2 interchangeable tools • powerful vacuum blower for fixing the material • Standard equipped with gray conveyor table (Conveyor). Green-blue exchange conveyor possible (offers high contrast for dark materials) Can be extended with other tools (on request): • EOT electric oscillating blade • POT pneumatic oscillating knife • PRT rotating blade • UCT universal blade • KCT Kiss-Cut tool • CTT creasing tool • V-Cut angle-cut cutting blade • Punching tool for pinches or holes • Printer mark detection • Camera registration Easy-to-use function • Easy interchangeable cutting tools, "PLUG & CUT • Intuitive user interface • Easy blade change • Vacuum zones can be activated with a click Fast amortization • Low cost with high added value • Best material utilization through nest expert software modules (not included in equipment) • High velocity • Constant precision Data: • Short cutting times due to high positioning speed up to 90 m/min. • Repeatabiliy +/- 0.25 mm • Cuts single or multiple layers • Suitable for both single ply and multi ply or sheet goods and roll goods (can be extended with suitable unwinder) Nwodpfx Ajif Ek Rokfef (Product photo as example) The machine is CE certified.

Year of construction: 2006, condition: like new (used), Container volume 32 m3 Nodpfsfhb Tkjx Akfowf

Year of construction: 2023, condition: new, ! Offers for customers from Baltic states only: Lithuania, Latvia, Estonia. Nodpfoixz D Ujx Akfswf Guillotine RAPIDO is fast reliable shearing machine. Depends on sheets length there are guillotines with different working lengths available: 1300 mm / 2600 mm / 3200 mm / 4100 mm. Machine can do up to 35 cuts per minute. The drive system with eccentrics, pulldown rods, and hold down system which can be positioned as close as 2.5 cm from the knives allow for easy and expedient trimming of narrow strips. RAPIDO guillotine shear is equipped with squaring arms on both sides and the LED cutting line light. Available working lengths: 2600 mm / 3200 mm / 4100 mm

Condition: reconditioned (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: HBC 140 2x75kW 2001 (210-008-01), pressing force: 155 t, bale weight: 1,500 kg, pressure: 250 bar, power: 150 kW (203.94 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Nwodpetvau Asfx Akfof Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Year of construction: 2009, condition: like new (used), Press with container Nodpfefhb Tiox Akfewf Engine 5,5 kW 400 V

Condition: ready for operation (used), Year of construction: 2008, functionality: fully functional, machine/vehicle number: 20194, travel distance X-axis: 4,000 mm, travel distance Y-axis: 1,200 mm, travel distance Z-axis: 1,500 mm, power: 49 kW (66.62 HP), Features High rigidity for heavy-duty machining Large table for oversized workpieces Nedpfxjx S Hgzs Akfewf CNC control with HEIDENHAIN TNC 530 for precision operations Automatic tool changer with 50 positions Centralized lubrication and hydraulic system

Year of construction: 1999, condition: good (used), Edgebander Biesse Polymac ERGHO 5, year 1999 Biesse Italy S/N 80709 max. panel thickness 10-45 mm min and max banding strip heught 13-60mm max thickness of banding material in rolls: 0,4mm- 3mm min. panel width 50 mm min. length 150 mm operating speed m/min 10/20 Technical information: Glue Pot VC 700 End trimming unit 701 Edge trimming unit RS 700 Corner rounding CR 200 Tilting Edge Trimming unit +Chamfering RI 700 Compact edge scraper RBK501 Brushes SP700 Edge Sanding unit LV 700 heated infeed guide PLC control panel support guide Large diameter roll holder edge cutting device for 3mm thick rolled edges Nwsdpsgtx Aqofx Akfef 400 V , 50 Hz CE- marked Dimensions of the Maschine: ( Lx W x H ) = 4950mmx 1700mm x 1530mm 2900 Kg Technical information under subject of correction