Vertical turning lathe

FREMTAS 16FR23

Year of construction: 1988, condition: used, machine/vehicle number: 103.071.3156.78192, disk of circular saw-Ø: 400 u. 425 mm cutting area at 90° round: 130 mm cutting area at 90° square: 120 x 120 mm cutting area in mitre at 45° round: 130 mm cutting area in mitre at 45° square: 110 x 110 mm cutting speeds: 11 u. 22 m/min forward feed speeds: 670 mm/min cutting length: m. automat. Vorschub bis 1200 mm electrical connection: 380 V, ca. 4 kVA V Djdpsz N Amsfx Aptswb sawing drive: 1,6/2,5 kW space needed: 1800 x 3800 x 2000 mm weight: ca. 1800 kg

Condition: excellent (used), Year of construction: 2015, operating hours: 22,387 h, Manufacturer: Hermle | Type: C 400 U | Serial number: 23589 | Year of manufacture: 2015 | Operating hours: approx. 8939 | Control system: Heidenhain TNC 530; Travel ranges (X/Y/Z): 850 / 700 / 500 mm; Swivel/rotating table: Ø 630 mm, integrated, C- and B-axis. Dwsdpjzq Dkxefx Aptob Tool magazine: 38 positions; Spindle speed: up to 18,000 rpm; Drive power: approx. 20 kW; Machine weight: approx. 8,000 kg; Cooling system: Knoll 850 K-1 with high-pressure unit; Coolant system; Central filter with return conveyor and heat exchanger; NC swivel rotary table; The operating hours refer to spindle operation. | Dimensions: approx. 4000 mm x 3400 mm x 2700 mm (W x H x L) | Approx. 10,500 kg | The specified dimensions are approximate values. All other information is provided without guarantee. | Grey | Steel Category: Machines and technical equipment

Condition: used, length:1800 mm Djdpecxxu Djfx Aptswb width:1200 mm weight of the machine ca.:1,6 t dimensions of the machine ca.:1,8 x 1,2 x 0,4 m

Condition: used, Wig welding machine L-TEC, Inverter TIG 200 DC type WIG welding machine for direct current DC Serial no. 184548, year of manufacture approx. 1994 Power: 200 Amps = 60% duty cycle 155 Amps = 100% duty cycle Adjustment range: stepless Current type: DC (direct current) Mains connection: 400 Volts, 50 Hz, 32 Amps plug - 4 meter hose set with central connection and hand torch - with remote potentiometer (foot switch) - gas pressure regulator - DC only - HF ignition Dwedpfx Ajdzqb Eeptjb Space requirement L x W x H: 850 x 480 x 740 mm Weight: approx. 150 kg The welding test yields very good results when welding stainless steel with direct current. Otherwise in good condition.

Condition: ready for operation (used), Year of construction: 2013, This Okuma MCR-A5C30x65 gantry milling machine was manufactured in 2013. It features a robust 100 mm spindle, capable of speeds up to 4000 min⁻¹, and accommodates a maximum workpiece size of 2540 mm by 5540 mm. The machine supports a hefty 30,000 kg on its 2500 × 6300 mm table. Ideal for heavy-duty milling with a rapid feed rate of 20,000 mm/min. Contact us for more information about this machine. Machine Benefits Technical Machine Benefits • Dimensions of machine (lxwxh): 2500 mm x 6600 mm x 6350 mm / weight (kg): 59000 kg • Max workpiece width: 2540 mm / max workpiece length: 5540 mm Dwsdpex D S Ekjfx Apteb • Table size (width × length): 2500 mm × 6300 mm /max load on table: 30000 kg table height from floor: 850 mm /effective width between columns: 3050 mm/ t-slot (width × number): 24h7 × 13 • Cutting feed rate: 1 to 10000 mm/min/ rapid feed rate: 20000 mm/min/ table movement x-axis: 6500 mm /x-axis travel: 6500 mm /y-axis travel: 3500 mm/ z-axis travel: 650 mm • Tool holder: bt50 + masz type/ tool storage capacity: 50 tools /max tool length: 300 mm • Power supply: 400v, 3 /phases, 50hz rated capacity: 513 kva /full load current: 741 a /peak current: 117/138 a /short circuit current: 18 ka • Spindle diameter: 100 mm /spindle speed: 30 to 4000 min⁻¹ • Large table size suitable for heavy loads. /extensive tool storage capacity. /high rapid feed rate for efficient operations.

Condition: used, swing diameter 2000 mm turning height 1800 mm Control Siemens Sinumerik 840 Dsl turning speeds range 2,8-315 U/min cross rail adjustment - vertical 1200 mm cross rail adjustment - horizontal +/- 1150 mm 1500 mm bit feeder section 240 x 240 mm Minimum immersion diameter 340 mm cutting capacity 50 kN max. torque on the faceplate 50000 Nm speed range step 1 2,8 - 80 U/min speed range step 2 12 - 315 U/min Max. clamping weight 12000 Kg power capacity faceplate 105 kW weight of the machine ca. 33 t dimensions of the machine ca. 10 x 5 x 6,5 m Further technical data: - Feed range of three-phase servo motors: 1–3000 mm/min; 0.01–50 mm/rev - Crossbeam travel speed: 425 mm/min Features/Accessories - Increased turning height (+600 mm) - Z-axis extended to 1500 mm - Magazine capacity: 20 positions - Magazine type: disc magazine - Max. tool length: 525 mm - Chip conveyor - Workpiece measurement - Renishaw probe - Coolant tank capacity: approx. 2000 litres - Coolant pump flow rate: 60 litres/min at 2 bar Dsdpfx Asy Dvlqjptowb Overhaul: - Extensively overhauled in 2012 by Siemens Industry Munich - Items overhauled included: control system, cabling, motors, measuring systems, etc. - Further information can be found in the PDF

Condition: new, cutting diameter 305 mm saw band length 3375 mm cutting width 350 mm dimensions of saw-band 3375 x 27 x 0,9 mm 305 mm Dwjdpfx Apeu Dbvtstjb 260 mm 350 x 200 mm 250 mm 230 mm 230 x 200 mm 175 mm 155 mm 170 x 100 mm total power requirement 1,5 / 1,8 kW weight of the machine ca. 0,7 t dimensions of the machine ca. 1,5 x 1,8 x 1,9 m

Condition: ready for operation (used), Year of construction: 2008, spindle speed (max.): 3,300 rpm, spindle motor power: 30,000 W, overall weight: 9,100 kg, controller manufacturer: MAZATROL, controller model: Mazatrol Matrix, number of axes: 3, This 3-axis Mazak QT Nexus 350 II M was manufactured in 2008. It features a Mazatrol Matrix control unit, a maximum swing over bed of Ø 830 mm, and a turning length of 1500 mm. The spindle supports speeds up to 3300 rpm with a power of 30 kW. It includes a chip conveyor and tool presetter. If you are looking to get high-quality turning capabilities, consider the Mazak QT Nexus 350 II M machine we have for sale. Contact us for more information. Additional equipment • Chip conveyor • Tool presetter • Autoblock chuck • Toolholders • User and maintenance manuals Dwjdsx D I Riepfx Apteb Machine Benefits Technical Machine Benefits • Max. Turning diameter: Ø 420 mm • Max. Turning length: 1500 mm • Bar capacity: Ø 102 mm • Spindle nose: asa 11” • Chuck type: autoblock Ø 315 mm • Tool size: 25 × 25 mm / Ø 50 mm • Driven tool motor power: 7. 5 kw • Max. Speed of driven tools: 4000 rpm Extra Information Machine still under power

Condition: new, TECHNICAL DATA Dwjdpfxefbgz Io Apteb Gas-fired preheating furnace, make VEI type: VEI_KO_V_GB_400-350 temperature: 350°C burners power: 2 x 200 kW fans: 2 x 4 kW useable dimensions x 2 (h x d x w): 1.000 x 1.400 x 2.800 mm

Condition: used, Lasko hammer KGK 063 Dsdpfju Eb Niex Aptjwb Impact force 630 mkp Stroke max. 630 mm Bear weight 630kp Top pressure - filling pressure 5 bar