Length stop

Graule RLH

Condition: new, Year of construction: 2026, Cut-to-length and mitre saw type: ZS 200 N - 5 KW motor with machine stand, Machine via handwheel and worm gear (rear) Tiltable Saw blade diameter 520 mm, saw blade mounting hole 50 mm Saw blade speed: 2800 rpm 400 volt / 5 KW (S6/40%) motor with brake and automat. Star delta motor control Cutting width at 90 degrees: 420 mm Podpfxsk H Ic Uj Afhopl Cutting width at 45 degrees: swiveled: 295 mm Cutting height at 90 degrees: 200 mm Cutting height at 45 degrees inclined: 140 mm Saw can be swiveled on one side up to approx. 25 degrees to an acute angle and tilted flat to the left up to 30 degrees Carbide circular saw blade 520x4.0/2.8 x 50 mm 60 WZ neg. for wood RLH-ST60 6.0 mtr. measuring length, mounting side: left Cross-cut fence / roller conveyor, heavy-duty design, Stop slide adjustable from the workstation via handwheel, electronic-digital dimension display, pneumatic clamping of stop slider, stop flap folds backwards, with steel rollers 60 mm diameter, roller spacing 200 mm, 400 mm roller width, with 4 support feet and connection piece: overall length: 6.7 mtr. Surcharge for digital electronic display unit type: FIAMA EP6 for 230 V mains operation, with electric on/off switch and socket. Powerful dark red LED display. Higher accuracy than the battery-powered crystal display RO-ST60 4.0 m long feed roller conveyor Mounting side: Right Heavy-duty design, steel rollers: 60 mm Diameter, roller spacing: 200 mm 400 mm roller width, 3 support feet and connection piece Location: From stock 54634 Bitburg - immediately available - Picture: similar. Machine is still in original packaging

Condition: reconditioned (used), functionality: fully functional, Year of manufacture 1997, connected load 380V 5.2A 2.0kW, saw blade diameter 350 mm, can be swiveled 45° on both sides, height adjustable with hand crank, cutting length 600 mm, extraction connection 100 mm, table height 890 mm, roller conveyor on the right with stop cutting length 3200 mm, roller conveyor on the left with stop cutting length 2200 mm Podpfx Aswhn T Uefhspl

Condition: new, Extraction capacity of filter unit at spigot*: 350 m³/h Total power consumption*: 0.09 kW Operating voltage: 230 V, 50/60 Hz, 1PH + N + PE Noise level*: 52 db(A) Dimensions L/W/H in mm: L 329 / W 374 /H 510 Colour: RAL 7035 Weight: 25 kg Manufacturer: ISI Industrieprodukte GmbH *Depending on the filter equipment Special voltage or special colour on request Application: Extraction of oil mist and smoke, for small to very large machine workrooms. Your advantages of the ELBARON series: - 18 unit variants available - Direct from the manufacturer - ISI-TRONIC as standard (digitalised filter control) - Electronically controlled EC fan as standard - Speed and air flow rate adjustable - Simplex (single-stage) or duplex (two-stage) available Psdpjh Rdwxsfx Afhspl - Wide range of air flow rates available - Adaptable to pollutant load and air performance requirements - Large range of mounting and connection accessories - Quality Made in Germany We have developed the ELBARON® filter series for use in machining operations with pure oil or for separating oil mist and smoke. For many years now, the digital electrostatic air filters of the ELBARON® series have been among the most efficient filter units on the market and are in use worldwide. Our filter units are already digitalised as standard and can be controlled, for example, using a laptop. The ELBARON® unit series comprises 18 unit variants and can be optimally designed for your application in terms of size and performance. ELBARON® units impress with their long service life and absolute functional reliability. Our electrostatic filter cells are dimensioned in such a way that the best possible filter efficiencies, service lives and trouble-free operation are achieved under economic aspects.

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, spindle bore: 20 mm, spindle speed (max.): 10,000 rpm, bar passage: 20 mm, Equipment: documentation/manual, CNC sliding headstock lathe Citizen L520, year 2000 control, Cincom Mitsubishi Meldas, Ppjdpfx Aet St A Tsfhsl 7 axes (X1/Z1/Y1/C1/X2/Z2/C2) Bar Ø max. 20 mm, turning length max. 205 mm, Main spindle, max. speed 10,000 rpm, C-axis 0.001 degrees, Counter spindle, max. speed 10,000 rpm, C-axis 0.001 degrees, Tool holder for a total of 18 tools (linear tool holder, front attachment, rear machining), Live tools on the main spindle FMB barfeeder Machine runs without problems or defects, can be inspected in production and seen running. Machine has all books and manual.

Condition: used, Length 2700 mm Width 1100 mm Height 850 +- 150 mm engine output 0,37 kW Electric capacity 0,5 kw compressed air 6 bar Horizontal impregnation system 'Pro flow' for individual parts with rinsing circuit. ----- Features: Machine for horizontal flooding of individual parts. The product will go through flooded a row of nozzles. The excess product is then removed through air jets blown off. The pump and the air nozzles are controlled automatically and only then operated when the workpiece passes through. In this way the Compressed air consumption reduced. The circulation operation ensures minimal product consumption. ----- Construction features: structure Sturdy steel frame, painted with high-strength, water-soluble products. Machine body made of heat-sealed, thick polypropylene plates. 4 independent chambers for inlet, flooding, blow-off and outlet. Horizontal feed of the workpieces By motor-driven rollers made of plastic with grooves. Electrical converter for controlling and changing the conveying speed. transmission The machine is equipped with an exclusive system so that all Gear located outside the flood chamber and easily accessible to the Podpenl Nqqsfx Afhjpl Operators are to guarantee a longer service life and the to facilitate maintenance operations. The moving components are protected by cover plates and appropriate seals protected. circulation pump Pneumatic double diaphragm pump made with valves, seals and diaphragms Nitrile rubber and housing made of plastic material (PVDF). air jets A blow-off system is present in the first chamber to prevent product leakage avoid. A second blow-off system after the flood chamber blows off the excess product from the workpiece. Electrical panel According to CE, degree of protection IP 55. Including inverter to the set feed rate. technical features Length mm 2700 Width mm 1100 Conveyor speed (min./max.) m/min 3-6 Motor power train group kW 0.37 Installed electrical power kW 0.5 Distance between infeed and outfeed rollers mm 2520 Working height (adjustable) mm 850 +- 150 Min. length of the workpieces to be flooded mm 250 Max. width of the workpieces to be flooded mm 300 Max. height of the workpieces to be flooded mm 250 Compressed air consumption lt/min 2000 Pressure of the required compressed air bar 6 Equipment and available accessories Flushing circuit for Pro Flow ----- Price of the above machine: on request! plus packaging and transport ----- (Technical information according to the manufacturer - without guarantee! Illustrations may be dated Deviate from the original, prices net, plus VAT (domestic))

Condition: used, Year of construction: 2008, fully equipped, with cutting extension to 540 mm incl. HM special blade 350 x 3.5 x 40, 108 trapezoidal teeth flat tooth, negative rake for aluminum cuts used, top condition, low hours Manufacturer: Graule Model: ZS 135 Year of manufacture: 2008 Machine no.: 2008/30/23 CE pattern tested Motor 2 kW Brake motor Cutting height approx. 135 mm Large cutting length extended to approx. 540 mm Blade diameter approx. 350 mm Saw blade bore approx. 30 mm Tiltable right Tiltable left Machine base Roller table right 3000 mm with stop and scale – RLH with handwheel adjustment, pneumatic clamping, and electronic digital display Roller table left 5000 mm, type RO Feed brake Psdpjww Nd Tjfx Afhjpl Material support made of aluminum Coolant spraying system 2 x pneumatic workpiece clamps right + left Pressure reducing valve Original price approx. €12,750.00 Location: 97447 Gerolzhofen, free loaded, unpacked Delivery in as-inspected condition, without warranty or guarantee.

Condition: new, Glass bead nailer "2 P Jumbo automatic E.C." - new - Your advantages: - The corner connections are closed - No open glazing bead joints - There are no color differences when painting - The glazing bead frames are easy to assign Clamp corner joining machine 2P Jumbo Automatic E.C. for clamping glazing bead frames. Choice between automatic and manual operation; With angle system, clamping device from above and front Pressure can be regulated separately. Inserting parallel and superimposed ones Clamps possible via electronic programming control. Stapler can be mounted on a suitable work table, Operation via foot valve. ----- Price in this version on request! Plus packaging/shipping ----- Pictures show Clamp corner joining machine 2P inlcuding the option of movable work table (please find details as follows under additional prices) Additional prices: ----- Movable work table height adjustable from 700 - 1000 mm, 2 pieces of support bars can be plugged in 1000 mm long, 2 pieces swiveling and sliding Support bars 1000 mm, support bars covered with felt, 4 swivel castors, 2 of which have a stop device. ----- Additional price: 1.321,00 euros net Brackets: packages 15 mm brackets (package of 2000): Price 22.00 euros Podpfx Asvnh T Njfhepl 12 mm brackets (package of 3000 pieces): Price 32.00 euros 10 mm staples (package of 3000 pieces): Price 32.00 euros Dimensions and weights ----- Jumbo Automatic E.C 470 x 370 x 300 mm, 35 kg Work table 32 kg All prices net. plus statutory VAT Ex works plus packaging and shipping (technical data according to manufacturer - no guarantee!)

Condition: refurbished (used), Year of construction: 2024, Manufacturer: Elumatec Type SA/ SAS 142 Overhaul year: 2024 Saw blade max. carbide: 500 mm Drive power saw motor: 4 KW Saw motor speed: 2800 min-1 Cutting speed saw blade 500 mm: 4400 m/min Saw height control: infinitely variable, fully electronic Working range square 90° max.: 130 x 130 mm Working range flat: 90° max.: 190 x 130 mm Working range round: 90° max.:150 mm Pneumatic feed length: 5-560, 10-1120 mm Compressed air connection, on site 6 bar Weight(saw)approx.: 800 kg Dimensions LxWxH (saw)approx.:2900mm x 1400mm x 1500mm Installation area LxW: 2900mm x 1400mm Additional description Elumatec SA/ SAS 142 4KW Retrofit Elumatec SA 142 4KW Retrofit Fully automatic sawing machine for non-ferrous metal and plastic After completion of the retrofit, the machine is in mint condition, both technically and visually. The machine will be overhauled in our company at the customer's request. Among other things, the following points were renewed: - Conversion to Siemens S7 PLC control - Conversion to Siemens HMI control panel - New electrical components - New pneumatic lines - Maintenance or replacement of all pneumatic cylinders and valve terminals - Maintenance of minimum lubrication system - Replacement of general wear parts - Overhaul of the cab Warranty: Unless otherwise agreed, we provide a 6-month warranty on all parts overhauled or replaced by us. Working time and wearing parts are excluded from the warranty. Optional: - Extension of the sawing area to flat 90° max.: 300 x 120 mm - Splitting extension (for a high-quality cut surface without return marks) Pedpfxsuiy Nyj Afhspl - Servo-controlled material feed - Saw blade feed Servo-controlled - Mass clamping device Feed vice - Delivery and installation on your premises - Training of your employees

Year of construction: 1998, condition: good (used), Used Emmegi Automatica 550 Single head cutting-off machine from 1998 in good condition for 90 degress cutting of aluminium profiles, with pneumatic bar feeder and stop, as well as adjustment of cutting length and tolerance op to +/- 0,10 mm of the required size. Specifications: • Blade diameter: 550mm • Blade drive power: 4 kW Pedpetlpl Hsfx Afhopl • Blade drive rpm (50hz): 2840 1/min • Total installed power: 4,3 kW • Operating pressure: 6-8 bar • Max. Feeder stroke: 500mm • Max. Clamp opening, feeder: 410mm

Condition: used, machine/vehicle number: 007350, X axis working area: 4000 mm Y axis working area: 1400 mm Working Table: Pod and Rail Main Electrospindle power: 15 KW Ppsdpfxswcyd Is Afhol Number of controlled axes: 4 axes Total number of drilling spindles: 30 Total number of tool changer positions: 28