Punching machine

Heidelberg Varimatrix 105 CS

Condition: good (used), Year of construction: 2013, Operating hours: only 14,500 - Format size – max. 750 x 1050 mm, min. 350 x 400 mm - Net die cutting area: 727 x 1050 mm - Materials: - Paper, min. 80 g/m² - Cardboard & solid board, up to 1400 g/m² - Corrugated board (B-flute) up to 4 mm - Die cutting pressure, max. 300 tons - Speed, max. 7,500 sheets/h - Pile height at feeder: 1000 mm (non-stop) Equipment & features: - Fully automatic die cutting, creasing, and embossing machine - Touch screen control panel - Stripping station for internal waste as well as side and rear edges - Centerline system Lrjdpfx Asx R Tiajdvoi - Small format device: minimum 300 x 350 mm - Non-stop automatic sheet feeder with pre-piling system - Non-stop standard delivery - Register system in feeder and die cutting station - Mechanical double sheet detector - Side lays on operating and drive side, switchable between pull and push lay - Four active front lays with sensors for sheet infeed control - Independent fine adjustment of front lays for drive and operator sides - Gripper margin adjustable, 10–18 mm - Delivery section with gripper margin removal - Stripe inserter in the delivery - Centralized and automatic chain lubrication - Two standard stripping frames - Two die cutting chases - Die cutting plate, 5 mm - Screw compressor Varimatrix 105-CS Note: All technical terms and specifications are provided as per industry standards for machinery listings in the printing and packaging sector.

Condition: ready for operation (used), Year of construction: 2006, Bobst SP102-BMA Foilmaster Equipped with: Fully Automatic Feeder Double Sheet Control Centre Line Hot Foil Unit 2 x honeycomb chase 2 x die cutting chase 16 Independent Heating Zones Foil Advance Shafts Automatic Delivery Lrjdpfx Adowgz Rkevoi Elevated (High Pile) Specification: Sheet Format Max: 720mm x 1020mm Sheet Format Min: 350mm x 400 mm Working Material Paper/Solid Board: 80-2000gr Corrugated Board: "E" and "B" - max. 4mm Gripper margin: 9-15mm Stamping Format: Max 680mm x 1010mm Max speed: 7,500 p/h

Condition: used, Year of construction: 1988, BOBST Printing Machine with 4 bottom colors anilox cilinders 120l/cm and 80l/cm TRANSFER BOBST FLATBED DIE CUTTER BOBST AUTOPLATINE SPO 1600, max format 1100 mm x 1600 mm / 43.3" x 63" with 4 Bottom Printing unit and transfer Bobst * Vacuum feeder * Die cutting section * Waste elimination section * Centerline II * High pile delivery with two lifting tables * Max sheet format: 1100 mm x 1600 mm / 43.3" x 63" * Min sheet format: 520mm x 600mm / 20.5" x 23.6" * Cutting force: 400 t * Materials: E, B, C, CB, BE flutes * Max speed: 6,000 sheets/hour Lredpfxsv Ifpus Advoi Possibility to sell them separately

Condition: refurbished (used), Year of construction: 2009, functionality: fully functional, overall weight: 52,000 kg, punching force: 600 t, space requirement height: 3,520 mm, space requirement length: 12,150 mm, space requirement width: 9,340 mm, Machine for punching, embossing, waste stripping and blanking Used machine, overhauled at the QTM Schwalmtal plant System equipped with high-performance sheet feeder for NON-STOP operation ⦁ For fully automatic punching, creasing and embossing with or without gripper edge Lredet E Nthepfx Advsi ⦁ for stripping the inner waste as well as the side and rear sheet edges ⦁ for stacking the punched and stripped sheets with the attached gripper edges or the attached gripper edges or ⦁ for cutting off the gripper edges and then depositing the remaining sheets in stacks remaining sheets ⦁ with a patented gripper carriage register system for maximum register accuracy ⦁ with a bundle stacking machine that features a fully automatic separating sheet feeder and NON-STOP delivery and does not need to be converted even for the smallest blanks. changeover even the smallest cuts. (Shuttle table with comb structure) ⦁ Cut-off sheet magazine with electrical stock control, during production refillable during production ⦁ with Centerline equipment ⦁ with automatic pallet changing device in the storage area ⦁ Modem ⦁ Standard elevation of the machine 600 mm Specification Sheet format max. 1060 x 1450 mm Sheet format min. 500 x 700 mm Maximum punching force 6.0 MN (600t) Speed 8,000 Bg / h Processable materials: Paper min. 80 g/m² Cardboard up to 2000 g/ Corrugated cardboard up to 5 mm (max. sheet curvature 4 %) Features: patented QTM rail system manual non-stop feeder stripping station depaneling station Centerline Fully automatic pallet changing device Deposit incl. platform Upgrade of the control system to Siemens S7 Completely overhauled machine drive Quick-clamping frame in all tool stations

Condition: ready for operation (used), Year of construction: 1983, BOBST SPO 1600 Max Speed 5000 per hour Year 1983 Max lenght 1075mm Lrsdpfx Aoxcayyedvei Max width 1580mm Fully reconditioned by Bobst 2015 Central line

Condition: new, Die cutting machine TYMC-1200 with hot stamping The latest version, with a „honeycomb” plate with locks. The machine is designed for hot knife die-cutting and standard die-cutting without the need to remove the heating plate. Format: die cutting 1230x850mm hot stamping 1100x780mm Weight 6000 kg Operating speed 23 cycles/min Foil travel 1-820mm Operating temperature 1-150’C Power supply 380V Equipment: Lodpswxtb Eefx Advjri – electromagnetic clutch and brake – quick assembly frame – control panel with a touch PLC programmer – three independent foil pulling systems, controlled by stepper motors – 3 operating modes: continuous, time delay, manual – 6 heating plate sections, energy saving – central lubrication – additional safety covers – photocells – operating tools and instructions, CE declaration – sheet for pressure Machine available immediately 12-month warranty.

Year of construction: 2021, condition: ready for operation (used), Features: automatic non-stop delivery with conveyor, non-stop feeder with rods, pull mark left, push mark right, quick clamping frame for tooling, lower stripping station, upper stripping station, two exchange frames for lower stripping station. Without die-cutting plates. Processable materials: min. paper 90g/m², max. solid board 2000g/m², max. corrugated board/ with MasterSet 4/ 2mm, max. sheet size 760x1060mm, min. sheet size/with MasterSet 300x350/ 350x400mm, max. cutting pressure: 2.6MN/ 260t, max. machine speed: 8000 sheets/h, max. feeder pile height without non-stop/ in non-stop operation: 1500/ 1200mm, max. feeder pile weight: 1500kg, max. delivery pile height: 1400mm, max. delivery pile weight: 900/ 1340kg. Operating hours: 1525h. An on-site inspection is possible. Lrjdpfx Aew Tc R Rodvei

Condition: used, functionality: fully functional, machine/vehicle number: 908108, fuel type: electric, Year of construction: 2009, Kama Pro Cut 53 (2009) with Mabeg M1/60/400 Suction head and Sidelay (2008) Fully operational and rarely used. Please message so a video of the machine operating can be provided. For cutting, creasing, perforating, kiss-cutting, cold embossing and Braille. Profitably even with small and personalised runs. Be it printed matter or packagings, offset or digital printing. Benefits • AutoRegister, aligns each sheet to a print mark • Multifaceted applications for the 530 x 400 mm format • Highest register accuracy (less than 0.1 mm) • Profitable finishing also of small runs • Clean cutting contours thanks to very few to no nicks • Moving upper table ensures gentle passage of the material • Space-saving design, requires only 4.5 m² Options • Motor-driven pressure control system (MPC) • Cutting pressure indicator on the display and automatic overload protection • Platen changing system (4+1 mm) • Module for hot cutting of plastic materials • Hot foil and hologram stamping module available for retrofitting Technical Features • Material: Paper, cardboard, plastics 80–800 g/m² • Maximum sheet size: 530 x 400 mm • Minimum sheet size: 210 x 148 mm • Maximum cutting size: 530 x 390 mm • Minimum gripper margin: 10 mm • Height of cutting blades: 23.8 mm • Maximum machine performance*: 6,000 sheets/h • Maximum cutting pressure: 120 tonnes • Maximum stacking height (sheet feeder): 700 mm • Maximum stacking height (delivery unit): 500 mm • Dimensions: 2.60 x 1.75 m Lsdpewh Tq Sjfx Advori • Net weight: 3,000 kg * dependent on material, sheet size and die configuration. when using a cardboard kit (option) or single-sheet feeding. Technical data and figures are subject to change.

Condition: used, Year of construction: 2018, operating hours: 6,90,00,000 h, functionality: fully functional, Folder gluer machine Lsdsyg Edgspfx Advjri Folding carton with longitudinal seam: max. 1,150 × 600 mm min. 75 × 55 mm min. 45 × 55 mm (with small carton device) Crash-lock bottom carton: max. 1,150 × 600 mm min. 146 × 80 mm 4-corner box (erected): max. 1,150 × 680 mm min. 120 × 110 mm 6-corner box (erected): max. 1,150 × 630 mm min. 250 × 130 mm With BELKHOFF control system Roller and drying tunnel TÜNKERS EAS 480 delivery station, right-hand, year of manufacture 2019

Year of construction: 2018, condition: excellent (used), Max sheet size: 1080 x 780 mm Max single product to take out: 450 x 450 mm Min single product to take out: 30 x 30 mm Paper pile height: 40 - 100 mm Lodpfx Adou I U N Usvjri