Roller leveller

KENNY TCL 150 A

Condition: used, Year of construction: 1984, turning diameter over cross slide: 1,600 mm, turning diameter: 2,000 mm, turning diameter over bed slide: 2,000 mm, turning length: 35,000 mm, workpiece weight (max.): 63,000 kg, Center Lathe SKODA - SUT 200 TD MACH-ID 9446 Manufacturer: SKODA Model: SUT 200 TD Year of manufacture: 1984 Tandem construction on one bed, with left and right headstocks Faceplate double tailstock left and right Double carriage Steady rest included Roller rest included Operator panel with scales requires attention and replacement Motorized tailstock for each side (left and right) 3-bed way design Torque on chuck: 160,000 Nm Minimum turning diameter: Ø 315 mm Industries served: - Shipyards - Propeller shaft manufacturing - Hydraulic cylinder shafts - Camshafts - Defence & Aerospace - Rolls and shafts for steel mills Fgsdpfeynky Aox Am Tjd - Crankshafts Specifications Metric / Imperial Turning length: 35,000 mm Swing over bed: Ø 2,000 mm Swing over carriage: Ø 1,600 mm Spindle power: 75 kW Bed width: 1,600 mm Quill diameter: Ø 400 mm Quill stroke: 250 mm Max spindle speed: 180 rpm Feed X-axis: 5,000 mm/min Feed Z-axis: 5,000 mm/min Workpiece weight: 63,000 kg Approximate dimensions: Length: 42,000 mm Width: 3,250 mm Height: 3,250 mm Weight: 158,000 kg Please note: The information on this page has been provided to the best of our knowledge and, where possible, obtained from the manufacturer. The information is given in good faith, but accuracy cannot be guaranteed. Accordingly, they do not constitute representations or contractual terms. We recommend verifying all important details.

Condition: good (used), CHARACTERISTICS Plate diameter ⌀; 3200 mm Maximum turning/turning diameter ⌀; 3300 mm - With upright forward; 3300 mm - With upright set back; 5600 mm Min. turning/turning diameter ⌀ - With advanced upright; 800 mm - With upright set back; 3100 mm Max turning height; 750 mm Control; FAGOR 8025 Spindle RPM (2 ranges); - 0,5 - 10 rpm - 10 - 40 rpm Motor Power; 80 hp Fodpfx Aer I Aykjm Tsgd Maximum table load; 30.000 kg

Condition: used, Year of construction: 1980, machine/vehicle number: A-07/471A, sheet width - max.:130 mm straightening roll diameter:40 mm :5 :2+2 Fgsdpfocxxx Rsx Am Tjd sheet thickness - min.:0,4 mm sheet thickness - max.:3,5 mm weight:0,4 t dimensions of the machine ca.:0,6x0,65x1,15 m with integrated, stepless adjustable Vari-drive, reversing, operating-mode switch for manual and automatic operation, introduction roller cage, position indicator of straightening rolls via analogue display, adjustment of straightening rollers via hand wheels, automatic swivel arm control, very good condition

Year of construction: 1987, condition: used, sheet width 150 mm coil weight 80 kg coil external diameter 650 mm Fedofn Aqljpfx Am Tegd 1000 mm diameter of the mandrel 230 - 445 mm total power requirement kW weight of the machine ca. t dimensions of the machine ca. m

Condition: ready for operation (used), Year of construction: 1969, Centre height: 355 mm Centre distance: 3000 mm Max. swing diameter over bed/gap/cross slide: 715/790/520 mm Spindle bore: 86 mm Spindle mount according to DIN 55027: Size 11 Quill taper of tailstock: MK 5 21 spindle speeds: 5.6 - 560 rpm 42 feeds longitudinal/cross: 0.09 - 5.6/0.045 - 2.8 mm 22 Whitworth threads: 2 - 28 TPI 28 metric thread pitches: 1 - 14 mm 27 module thread pitches: 0.25 - 3.5 module 32 module threads: 4 - 56 module 32 diametral pitch threads: 8 - 112 DP Drive motor, pole-changeable: 380 V, 7/11 kW Weight approx.: 7 t Fedoxpuu Espfx Am Tsgd Space requirement approx.: 6000 x 2300 mm

Condition: used, Radial drilling machine CSEPEL, Type RFh 75 / 1500 Machine no. 13704, Year of manufacture 1985 Drilling capacity in steel: Ø 75 mm Fjdelhwr Repfx Am Tsgd Drilling capacity in cast iron: Ø 90 mm Spindle mount: MK 5 Nominal overhang: 1500 mm Maximum overhang of the spindle: 1500 mm (to the column) Minimum overhang of the spindle: 440 mm (to the column) Distance from spindle nose to clamping surface: 370 - 1700 mm Overarm vertical adjustment: 950 mm Table size / clamping surface: 1800 x 1100 mm Column diameter: 450 mm Quill stroke: 380 mm Spindle speed: 19-1900 rpm, 21 steps Feed rate: 0.047-2 mm/rev, 12 steps Motor power: 11 kW Mains connection: 380 Volts, 50 Hz, 15 kW - Right-hand and left-hand rotation of the drilling spindle via hand lever switch - Hydraulic gear change for spindle speed and feed rate - Hydro-mechanical central clamping device - Motorized overarm vertical adjustment - Without coolant system - Machine light - Operating manual Space required: Length 2720 mm x Width 1170 mm x Height max. 3770 mm Transport height with motor on the column: 3500 mm Transport height without motor on the column: 3250 mm Weight: 6.3 tons Good condition

Condition: good (used), Make: Ursviken Type: VPF 1000/800-5,0 Control: Siemens Simatic panel Year: 1970 Hydraulic press for fabrication off large componts like dish heads tanks boiler shipyard and steelconstruction Fgedokvmi Sspfx Am Tsd Renewed in 2015 with Siemens SIMATIC panel and E-Cabinet Rittal Build in height 2950 mm Maximum die height 1500 mm Movable Table & Piston in X-Ways Large package Die tooling radius 10/20/30/50/60/80/100 Pressing force 210 kg/cm2 Maximum stroke 800 mm Machine 2350 mm placed in ground Specifications Metric US Standard Capacity Kg 1000 Ton Distance between column 5010 mm Table Length 3000 mm Table Width 2000 mm Table Height 550 mm Ram stroke 1450 mm Approche speed 50 mm/min. Working speed 5 mm/min. Return speed 50 mm/min. Dimensions (Estimate) Length 0 mm Width 0 mm Height 0 mm Weight 0 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: excellent (used), travel distance X-axis: 10,000 mm, travel distance Y-axis: 2,100 mm, travel distance Z-axis: 1,300 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 30 m/min, rapid traverse Z-axis: 30 m/min, feed rate X-axis: 30 m/min, feed rate Y-axis: 30 m/min, feed rate Z-axis: 30 m/min, spindle speed (max.): 6,000 rpm, spindle speed (min.): 36 rpm, pivoting range: 360 °, SHW PowerSpeed 5 Travel Paths • X-axis (Bed): 10,000 mm • Y-axis (Vertical): 2,100 mm • Z-axis (Horizontal spindle): 1,300 mm Control System • CNC Control: Heidenhain iTNC 530 Feed Rates • X, Y, and Z axes: 2 - 30,000 mm/min • Acceleration: 3.5 m/s² Universal Milling Head in Orthogonal Design Fsdpoxgq Ayefx Am Tjgd • Milling head holder swivel range: 360 x 1 degree • Milling head swivel range: 180 x 1 degree • Tool holder: SK 50 DIN 69871 • Spindle speed range: 36 – 4,000 rpm o Intermittently 36 – 6,000 rpm Automatic Tool Changer • Tool magazine for 48 tools Coolant System • Tank capacity: 500 l About the company MBM MBM Maschinenservice & Gebrauchtmaschinen GmbH is an independent specialist for SHW machine tools. Our main focus is on tool milling machines. Our services include supply of spare parts, on-site customer service, machine overhauls, and control system modernization. Services: - Used machines - Spare parts - Customer service - Machine service - Machine overhauls - Control system modernization ---- Used machine - used milling machine - used travelling column milling machine - orthogonal milling head - metalworking - tool milling machine - milling head - SHW machine - SHW spare parts - used milling machine - used fraesmaschine - used CNC milling machine - used bore milling machine - used metal milling machine - used metal mill - used metal milling machine - used CNC mill - CNC fraesmaschinen - CNC milling machines - milling machine - large component machining - large part machining - CNC large part machining - milling - SHW - PS5 - PS 5 - Powerspeed - SHW PSZ 5 - SHW Powerspeed - SHW Powerspeed 5 - PSZ 5 - Heidenhain - MBM milling machine - MBM machine - column milling machine

Year of construction: 2007, condition: used, gear hobbing diameter - external 1200 mm gear hobbing diameter - internal 1200 mm gear hobbing width -max. 260 mm Fjdpfxew Rf S Eo Am Tsgd control Liebherr PC-NC max. workpiece diameter 1500 mm table diameter 900 mm table bore diameter 320 mm max. table load 95 kN power capacity 30 kW coolant pump 120 l/min Axial distance between thrust spindle - table 0-820 mm Shaping spindle diameter 125 mm tool taper SK 45 DIN weight of the machine ca. 26 t dimensions of the machine ca. 8,073 x 6,183 x 4,375 m Strokes: - Stroke length min./max. - 0 mm / 270 mm - Stroke length adjustability - 270 mm - Stroke rate (double strokes) - 10 to 270 DH/min Equipment/accessories: - Chip conveyor - Cutting wheel holder SK 45 DIN - Cooler - Technical documentation

Condition: excellent (used), Year of construction: 1987, pressure 320 t plate thickness 0 mm no. of strokes 80 Hub/min pressing capacity total 320 t stroke 30 - 80 mm table surface area unten: 630 x 740 mm table surface area oben: 630 x 630 mm total power requirement 60 kW This fineblanking press FEINTOOL HFA 320 was completely overhauled in 2019 and is in new condition with new CE mark MAIN RAM total force (nominal) 320 to stroke min. 30 mm Fgjdpfxovwgl No Am Tjd stroke 80 mm V-RING nominal force 160 to stroke 30 mm COUNTER RAM nominal force 80 to stroke 30 mm TOOL DIMENSIONS lower table - width 630 mm lower table - depth 740 mm upper table - width 630 mm upper table - depth 630 mm daylight max. 320 mm ELECTRICAL SPECIFICATIONS total power consumption 60 kW