Deburring Machine

LISSMAC SMD 123 RE

Condition: new, Year of construction: 2023, sheet width 1540 mm plate thickness 4 mm upper roll diameter 110 mm diameter of lower rolls 110 mm bending roll diameter 110 mm Dcjdpfjvx Uvxex Abzeh total power requirement 1,1 kW weight of the machine ca. 0,9 t dimensions of the machine ca. 2,5x0,6x1,1 m New machine Cone bending equipment, hardened and ground rollers, motorized bending roller stationary control panel, digital display bending roller right and left, digital display bottom roller

Condition: new, DESCRIPTION DM100 Z2C - performs edge rounding and removes sharp burrs from both the inner and outer edges of steel, stainless steel or aluminium parts after laser, shear or punch cutting of metal parts from 50 x 50 mm up to 1100 x 100 mm in size. Ekdjtxp The 1st station processes the products through a contact roller (approx. 55° shore) with an abrasive belt and removes strong burrs in the first step. The 2nd station processes the products with 2 counter-rotating cross belts each from below and from above. The cross belts round off the parts to be machined on both the inner and outer edges. A big advantage is also the deburring of products with surface protection foil, because only the edges are processed without damaging the foil. Technical data - DM1100 Z2C: Working capacity (Ø mm) 1100x100 No. of belt stations (Z) 1 No. of cross belt stations 2 Abrasive belt, dimensions (mm) 1100x2200 Abrasive belt speed (m/s) 8-22 Cross belt speed (m/s) 2-8 Feed speed (m/s) 0.6-3.2 Sanding belt motor per head (kW) 18.5 Cross belt motor (kW) (2x) 3 Feed motor (kW) (3x) 0.18 Dcodpfx Abjd Ixadszjh Total power (kW) 33 Power consumption (A) 62 Rod suction connection per head (Ø mm) 150+185 Dimensions (mm) 3600x2330x2350 Weight (kg) 5000

Condition: new, Year of construction: 2026, -TFON Edge Rounding & Surface Purification System -Material Compatibility. Mild Steel, Aluminum, and Stainless Steel -Working Thickness Range: Accommodates material thicknesses from 0 to 120 mm. -Edge Rounding Provides Radius 2 edge rounding for smooth, safe edges that enhance both the appearance and functionality of the workpiece. -Precision Control: Equipped with a Siemens automation system for accurate and consistent control throughout the entire process. Independent Stations: Multiple processing stations enable versatile operations, allowing different tasks to be performed simultaneously or sequentially. Dsdpfohq A T Ujx Abzoch Table Options: Available working table sizes of 650 mm, 1000 mm, or 1300 mm to meet specific production requirements. Table Types: Flexible configurations including magnetic, vacuum, or magnetic-vacuum tables ensure secure support for various materials and part sizes. Plasma and Oxygen Technology: Utilizes advanced plasma and oxygen technology to effectively remove heavy burrs and dross after cutting, delivering cleaner and smoother surfaces. Surface Purification: Efficiently removes surface contaminants such as rust, oxide, and scale, preparing parts for further processing. Edge Rounding for Coating: Prepares parts perfectly for painting and coating by ensuring a uniform, imperfection-free surface. Industry Applications: Ideal for Steel Service Centers, Energy, Mining, Construction, and Automotive sectors, offering tailored solutions for heavy-duty applications. Uniform Results: Six flap wheels operate in unison to provide consistent, equal radius edges on every part. Pneumatic Oscillation System: Extends the lifespan of emery bands by minimizing wear and maintaining consistent performance over time.

Condition: used, Aufspannplatte - Tisch einer Langhobelmaschine - Tischbreite/Aufspannbreite: 1845 Dcjdpfxjbn Amfo Abzjh Tischlaenge/Aufspannlaenge: 5505 mm 7 T-Nuten laengs fuer T-Nutensteine: M 30 T-Nutenabstaende zueinander: 263 mm Gesamtlaenge: 6230 mm Plattenhoehe insgesamt: 350 mm Gewicht: 11 t

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, year of last overhaul: 2025, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Dcodpfx Absvf E Avjzeh Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: ready for operation (used), Year of construction: 2005, A Hennecke HK135 high-pressure polyurethane foaming system with four 25000l mixing tanks, a casting robot and two release agent robots is available. Capacity: 225t/24h, tool carriers: 42, mixing positions for additive mixing: 10, mixhead type: MQ, max. working pressure: 180bar, pressure tank: 330bar. Foam types: Rigid foam, rigid integral foam, semi-rigid integral foam, semi-rigid filling foam, cold-curing flexible foam, hot-curing flexible foam. Multiple mold foaming is possible. Complete documentation available. On-site inspection is possible. Dedpettbd Nofx Abzsch

Year of construction: 2013, condition: good (used),  Plasma cutting and extraction table, dimensions 2.500 x 6.000 mm.  Gantry bridge. Dcsdpfxstp Dhpe Abzsh  Carriage with servo-drives (to position the gantry bridge in X-direction).  Machine track, length 8 m.  HEB450 profiles for the foundation of the machine track, 8 m.  Plasma cutting unit Hypertherm HPR 400XD, 1 pcs.  Plasma bevel cutting unit, including automatic height control system.  Fume extraction unit Filtercube 4H for plasma cutting unit.  Oxy-fuel cutting torch, 3 pcs.  Automatic height control system IHT M4000 CAP for oxy-fuel cutting unit, 3 pcs.  Torch suspension for oxy-fuel torch (motor driven).  Torch suspension Single Drive for oxy-fuel torch, 2 pcs (automatic torch positioning).  Laser pointer (to align and position the torch).  Computer control system (consisting of an industrial PC and a control panel).  Control software 'VACAM Machine Edition' (including VaCad and VaNest software and online support).  Automatic nesting software Sigmanest "Powerpack" (including 3 days of training for max. 3 persons at Voortman Holland (excluding travel costs and board and lodging) and 1 day online-support).  Emergency stop with stop cord.  Year of build: 2013.

Condition: new, Year of construction: 2023, functionality: fully functional, Drying system / dryer suitable for various materials such as powder, granulate etc. Dcsdpfxsqu R Nas Abzsh - Control for temperature regulation This machine is connected and ready for testing in our machine hall.

Condition: used, Year of construction: 2004, Sato cutting machine for sale Dcsdovx N I Nspfx Abzsh

Condition: used, Technical details: turning diameter: 626 mm Dcodevgmimopfx Abzoh turning length: 3000 mm Turning diameter: 600 mm spindle bore: 100 mm spindle turning speed range: 2800 U/min weight of the machine ca.: 18 t Machine overhold and retrofit in 2003 with SIEMENS 840 D control - NC steady rest - 12-fold revolving head - splash doors - tailstock - coolant device *