Used Arbeitskorb V 1500 Ab for sale (44,980)

Condition: ready for operation (used), Year of construction: 2009, Technical data: Product number: WV 1500 C 001 Year of manufacture: 2009 Capacity: 1500 m3/h Maximum vacuum: 0.4 mbar The booster pump must operate together with an oil-sealed pump with 2-3 times lower capacity. Device after major overhaul, ready for operation. New seals and bearings, new oil. Bwedpfx Agexdvuio Hsn Achieves vacuum of 0.4 mbar.

Condition: used, Year of construction: 2002, grinding diameter 450 mm grinding length 1500 mm centre height 225 mm Control FAGOR EQUIPEMENT - T1: grinding wheel diameter 500 mm - T2: grinding wheel diameter 400 mm - T6: HF Fischer spindle MFV or MFZ 1224/1242/1260 - T7: HF Fischer spindle MFV or MFZ 1224/1242/1260 - Marposs tool measurement - active longitudinal positioning - Elaso GAP-control on T1 and T2 contactless integrated in the control surface - Elaso GAP internal grinding with fluid sensor for T6 and T7 - semi-automatic balancing by Elaso integrated in the control surface for T1/T2 - tailstock hydraulic with fine adjustment +/- 150 microns - dresser on workpiece spindle side table mounted - dresser on tailstock side table mounted - dresser on upper table - new service- and userfriendly housing SPECIAL EQUPEMENT: Workhead with direct drive - strongly recommended for non-circular grinding - workpiece weight flying max. 75kg - workpiece weight between centres 150kg - water-cooled B-axis with direct drive - center height 225 mm - extremely torsionally stiff - highly accurate positioning - resolution ° - water-cooled Hydrostatic ball screw - x-axis - wear-free, as there is no contact during operation - no loss of precision, even during long-term use at full load and maximum speed - no friction at low speeds - no friction force backlash when the direction of rotation changes - translates even the smallest rotational movements - no stick-slip effect even at low speeds - no fluctuations in frictional torque due to ball circulation - higher axial stiffness compared to ball screws - significant improvement in damping, resulting in better workpiece surface finish and tool life - no oscillations due to ball circulation - also suitable for high speeds and accelerations - cost-effective alternative to the linear motor with greater precision and significantly lower heat generation - significantly less power dissipation and, as a result, no problems with swarf on permanent magnets Bjdpsuxfu Nofx Ag Hswn New hydraulic unit - optimized temperature control (chiller) - Energy-saving Only one pump controlled by VFD - Pressure monitoring - monitoring of the hydrostatic oil for water content. (Damage to the bellows is recognised and detected prematurely) -fine adjustment +/- 150 microns Paper belt filter 375l – alternative 480l Grinding mist extraction system – emulsion MECHANICAL OVERHAUL -complete machine according to Kellenberger protocoll -new painting ELECTRICAL OVERHAUL - new modern Fagor CNC with BEMA HMI - new electric cabinet - new digital drive technology - replacement of all electrical cables, switches etc. - new absolute external scales in x- and z-axis - new absolute encoder (B-axis) Grinding software BEMA-Standard: - workpiece zeroing - grinding wheel zeroing - dressing diamond measuring - corrections - external and internal surface grinding - external and internal angle grinding (turning of the b-axis, dressing with straight wheel) - external and internal radius grinding (radius dressed on wheel) - semi-automatic traverse grinding - workpiece zeroing - 2 dressing diamonds - 1 dressing blade - dressing roll - 3 flat dresser - corrections - Z-position measurement - GAP control Optional grinding cycles at no extra charge: Profile plunge grinding: - external and internal profile plunge grinding with profile wheel Pr...

Condition: used, grinding diameter 350 mm grinding length 1500 mm centre height 175 mm Bwjdpfst Ii Rfsx Ag Hjn Grinding wheel left 500mm diameter Grinding wheel head fix. No swivelling possible. With new control. With new enclosure Overhauled according to Kellenberger protocoll

Condition: new, Year of construction: 2025, functionality: fully functional, travel distance X-axis: 1,500 mm, travel distance Y-axis: 1,000 mm, travel distance Z-axis: 700 mm, spindle speed (max.): 8,000 rpm, Traveling column machine Bsdpfx Ajvwip Dsg Hjwn New machine Work table clamping area mm 1500 x 1000 Table height mm 750 Number of T-slots 6 Size of T-slots DIN 650 mm 18 Travel paths X-axis mm 1500 Y-axis mm 1000 Z-axis mm 700 Distance table top edge - spindle bottom edge min/max. mm 150 / 850 Main spindle drive for speed 8000 min-1 AC motor, frequency controlled kW 16 at 44% ED Speed range: min -1 15 – 8000 Torque at 44% ED Nm 104 constant up to min -1 1500 Feed drives X-axis AC servo motor kW 3.5 Y-axis AC servo motor kW 2.0 Z-axis AC servo motor kW 3.5 Rapid traverse speeds (X/Y/Z): m/min. 30/30/20 Indirect position measuring system. Accuracy Positioning accuracy X, Y axis to 1000 mm mm ± 0.0150 Repeatability X, Y axis mm ± 0.0075 Positioning accuracy Z axis mm ± 0.0150 Repeatability Z axis mm ± 0.0075 Tool magazine 24-way - Tool positions 24 - Tool shaft (DIN 69871 / 69872) SK 40 - Max. tool diameter mm 76 - Max. tool length mm 250 - Max. tool weight kg 8 Machine control Heidenhain TNC 620

Condition: used, mileage: 4,46,000 km, power: 330 kW (448.67 HP), first registration: 03/2014, fuel type: diesel, overall weight: 32,000 kg, brakes: retarder, gearing type: mechanical, emission class: euro6, Equipment: soot filter, Arocs 3245 8x4 Hiab 26T (with German TÜV...) ----- Retarder – air conditioning – trailer hitch – Hiab 26T Suspension: leaf springs Bwedpfx Aoyxkc Hjg Hsn

Condition: ready for operation (used), Year of construction: 2000, functionality: fully functional, stroke length: 215 mm, throat depth: 410 mm, bending force (max.): 85 t, distance between stands: 1,750 mm, working length: 2,050 mm, TECHNICAL DETAILS Press force: 85 t Bending length: 2,050 mm Distance between uprights: 1,750 mm Stroke: 215 mm Bwsdpfx Agjyhmdqe Hen Throat depth: 410 mm MACHINE DETAILS Control: DELEM Dimensions & Weight Machine dimensions: 2,700 x 2,100 x 2,400 mm Weight: 7,900 kg EQUIPMENT Two-hand operation 2 support arms Side safety doors Lasersafe Fissler Wila tool clamping Adjustable die position Crowning system Tool cabinet

Year of construction: 2008, condition: good (used), Centralized dust, fume, and solid pollutant extraction system for industrial facilities. The VAC unit is an ideal choice for a high vacuum system for welding fume extraction and dust removal from grinding and polishing processes. Bedpjpug Dpofx Ag Hswn Capacity: 1,500 m³/h at 20,000 Pa vacuum Max vacuum: 22,000 Pa Inlet diameter: 135 mm Motor power: 22 kW Includes FlexFilter DX filtration unit with ATEX explosion relief panel (the panel discharges pressure in the event of an explosion). Separation efficiency: approx. 99.95% (fine dust) Additional cartridge filters on the clean air outlet. Noise silencer. The device is equipped with a new set of filter bags.

Condition: new, messurements (LxWxH): 1,10 x 1,15 x 1.40weight approx.: 1,150total power requirements: 4sheet thickness: 6 mm Details: - Hydraulic drive - Blade length: 200 mm - Adjustable angle: 60° - 140°, 6 mm Bwedsd Ab Idspfx Ag Hjn - Adjustable angle: 30° - 59°, 4 mm

Condition: new, Year of construction: 2026, Set Including LUFT 1500 COMPACT Screw Compressor with VSD Inverter and N10S Refrigeration Air Dryer The LUFT series screw compressor from the Polish brand CORMAK represents the latest innovations in pneumatic systems, combined with high-quality materials and components. Low operating costs, ease of use, ergonomic and solid construction, and high performance guarantee efficient and trouble-free operation. Additional Dual Filtration at the Dryer Included! Key Features Innovative Design Our screw compressors are based on advanced engineering and European manufacturing precision. The robust construction, enhanced with modern components, ensures long-lasting and reliable operation in all working conditions. Efficiency Optimization Thanks to variable speed drive (VSD) technology and intelligent algorithms, the CORMAK LUFT 1500 COMPACT screw compressor dynamically adjusts energy consumption to the current demand for compressed air. This results in significantly lower operational costs while maintaining maximum performance. Integrated Refrigeration Dryer The COMPACT version with a built-in refrigeration dryer provides a space-saving and comprehensive solution in a single device. The integrated dryer ensures dry and clean compressed air, protecting your system from corrosion and damage. Quiet Operation & Comfort Designed with attention to detail, our screw compressors operate at exceptionally low noise levels. Effective noise reduction and vibration damping systems ensure a comfortable working environment, improving operator focus and overall workplace comfort. Smart Control The intuitive MAM electronic control panel is the command center of your compressor. It allows precise parameter monitoring, maintenance scheduling, and quick diagnostics—ensuring system stability and protecting key components. Adaptability to Your Needs We understand that each application is unique. CORMAK screw compressors can be configured with additional air treatment systems, allowing for perfect alignment with your industry's specific requirements. Dynamic Working Pressure Automatic pressure regulation ensures the compressor delivers exactly the amount of compressed air needed at any given moment, maximizing energy efficiency and minimizing losses. Sustainable Development We are committed to environmentally friendly solutions. The energy-efficient technologies used in our compressors not only reduce your electricity bills but also limit environmental impact. Bodexmg Npjpfx Ag Hjwn Integrated Refrigeration Dryer – Top-Level Air Quality Two-Stage Drying System Effectively removes moisture and protects your pneumatic installation. Variable-Speed Fan Automatically adjusts cooling performance to working conditions, improving energy savings. Dual Filtration System Pre-filter with 3.0 µm precision removes larger solid contaminants. Fine filter with 0.1 µm precision captures oil aerosols and other small particles, delivering ultra-clean air. Technical Specifications Specification Value Motor Power 11 kW Voltage 400V / 50Hz Air Delivery (0–6 bar) 1620 L/min Air Delivery at 6 bar 1580 L/min Air Delivery at 8 bar 1350 L/min Air Delivery at 10 bar 1230 L/min Outlet Connection Diameter (G) 1" Dimensions (L x W x H) 1550 x 740 x 1150 mm Weight 500 kg

Condition: new, Year of construction: 2026, LUFT 1500 Screw Compressor with Inverter is a state-of-the-art solution used in pneumatics, combining high-quality materials and components. Low operating costs, ease of use, ergonomic and durable design, and high efficiency ensure effective and trouble-free operation. The LUFT 1500 INVERTER stands out with its direct drive, which offers significantly better efficiency and lower power losses compared to belt-driven models. This innovative solution ensures optimal use of motor power, resulting in higher performance with lower energy consumption. The maximum pressure generated by this screw compressor is 10 bar. Full control over operating parameters is provided by the intuitive MAM series electronic control panel, giving access to key compressor data and improving flexibility and control over your processes. Technical specifications: Motor power: 11 kW Voltage: 400V / 50Hz Output at 0–6 bar: 1620 L/min Output at 6 bar: 1580 L/min Output at 8 bar: 1350 L/min Output at 10 bar: 1230 L/min Bwsdpjxnxzajfx Ag Hsn Outlet connection diameter (G): 1" Dimensions: 1170 x 730 x 1020 mm Weight: 243 kg Manufacturer: Cormak

Condition: new, Year of construction: 2026, Three-phase 400V motor with frequency converter (kW) 4.0 Table dimensions (mm) 600 x 600 Cutting width (mm) 400 Cutting height (mm) 390 Cutting speed (m/min) 50 – 1000 Saw blade dimensions (mm) 3600 x 13 x 0.9 Machine dimensions without packaging (mm) 2225 x 1120 x 770 Weight (kg) 465 Standard features Precision drive controlled by a frequency converter Digital speed display Infinitely variable belt speed Balanced belt pulleys Hard rubber-coated running surfaces Hardened and ground guide jaws LED workstation light Height-adjustable guide arm Machine color RAL 7005 / RAL 7035 12-month warranty for single-shift operation OPTION Item No. 410.020 Machine price €15,450 Incl. minimum quantity slicing and longitudinal stop DELIVERY: FREE DOOR (within Germany) NOT THE RIGHT MACHINE? Bwodsir Ey Iopfx Ag Hen WE ARE A FLOTT SUPPORT POINT PARTNER AND CAN OFFER YOU ALL PRODUCTS FROM THE FLOTT RANGE! ASK FOR A QUOTE!

Condition: used, Clamping plate, welding table, welding table, straightening plate -Width: 1500 mm -Length: 1500 mm -Height: 125 mm -Surface: good -Holes: Ø 50 mm -Transport dimensions: 1500/1500/H125 mm -Weight: 1500 kg Bwodob Hzggepfx Ag Hjn

Condition: good (used), Frequency converter, frequency transformer, drive converter, controller, variable speed drive -Power: 1.5 kW -Output: 3x 230 V -Output frequency: 0-120 Hz -Number: 1x converter available Bwsdpfxsd Drx Ee Ag Hon -Price: per piece -Dimensions: 205/250/H190 mm -Weight: 6 kg/piece

Condition: new, bore capacity in steel (diameter) 60.0 mm threading M 42 throat 350 mm bore stroke 200 mm turning speeds 60 - 1530 U/min table: 720 x 510 mm bore spindles - Morse Taper 4 Kurzspindel MK column diameter 200 mm feed 0.15-0.2-0.3-0.36 mm/U Bwodpfx Agoxabgij Hen distance spindle /table 159 / 884 mm engine output 3.6 / 4.3 kW weight 605 kg Machine height 1950 mm Furnishing : - automatic feed with electromagn. Feed clutch - 4 feed levels 0.15 / 02, - 0.3 - 0.36 mm / rev - stepless speed adjustment - digital speed display - Feed overload protection - Spindle protection with electr. validation - digital speed display - machined base plate including special equipment: - Coolant device mounted in the foot pos. 24. - Thread cutting device pos. 20.0 - LED machine light pos. 12.

Condition: new, bore capacity in steel (diameter) 40.0 mm bore capacity in cast iron 50.0 mm throat 300 mm bore stroke 160 mm morse taper 4 MK table: 615 x 430 mm threading 24 in ST M threading 30 in GG M turning speeds 100 - 1.800 U/min feed 0.1-0.2-0.3-0.4 mm/U distance spindle /table 147 / 688 mm total power requirement 0.6 / 1.8 kW weight 470 kg height of the machine 1865 m Furnishing: - Electromagnetic feed clutch - with overload protection and electrical cross-handle switch Bwedpfjxaa R Hox Ag Hjn - Lockable main switch - Motor protection switch - Mushroom pushbutton (latching) for EMERGENCY STOP, in the front panel - Infinitely variable speed adjustment - Digital speed display - Protection class IP 54 - Spindle protection with electrical fuse - Motor insulation class "F" (155 degrees) - Operating instructions in German including special equipment: - LED machine light pos. 12. - Thread cutting device pos. 20.0 (Thread cutting with stop) - Coolant device "A" pos. 24. (Coolant base plate, complete) - digital drilling depth display pos. 37.1 (5-digit LED display)

Condition: new, bore capacity in steel (diameter) 50.0 mm throat 300 mm bore stroke 160 mm threading M 30 turning speeds 100 - 1600 U/min table: 615 x 430 mm bore spindles - Morse Taper 4 Kurzspindel MK column diameter 145 mm feed 0.1-0.2-0.3-0.4 mm/U distance spindle /table 147 / 688 mm engine output 1.8 / 2.9 kW weight 450 kg Machine height 1865 mm Furnishing : - automatic feed with electromagn. Feed clutch - 4 feed rates 0.1-0.2-0.3-0.4 mm / rev - stepless speed adjustment - digital speed display - Feed overload protection - Spindle protection with electr. validation - digital speed display - machined base plate - Motor 1.8 / 2.9 KW - 100 - 1600 rpm. Special accessories included: - LED machine light pos. 12. Bwedpfx Agsxabq Ij Hon - Thread cutting device pos. 20.0 (Thread cutting with stop) - Coolant device "A" pos. 24. (Coolant base plate, complete) - digital drilling depth display pos. 37.1 (5-digit LED display)

Condition: excellent (used), Year of construction: 1997, pressure 170 t chamfer lenght 4080 mm distance between columns 3680 mm column arm 410 mm dayligth 385 mm stroke 215 mm ajustment speed 200 mm/sec working feed 1-10 mm/sec return speed 135 mm/sec Bwjdsxcp Rbopfx Ag Hsn table width 200 mm table height 1050 mm Number of working hours 25.430 h oil volume 350 l total power requirement 29 KVA weight of the machine ca. 16.450 kg. range L-W-H 4620 x 2210 x 2885 mm Machine in good condition Regularly serviced by the manufacturer CNC backgauge with 8 axes (!!) - in checked conditions - machinevideo - ?v=yEaRj0XJAC4 Equipment: - CNC electro-hydraulic press brake/die bending press - DELEM CNC control - swiveling front left * High-resolution graphic screen * Clear, concise menus in the operator's language * Large tool and product library * Graphic 2D programming * Automatic bend sequence calculation and collision detection * Emergency stop button at front - CNC axis adjustment: * Y1 - Y2 - X1 - X2 - R1 - R2 - Z1 - Z2 axis + CNC crowning - X axis - adjustment speed: 500 mm/sec. * Max. stop range: 860 mm - R axis - Adjustment speed: 300 mm/sec. * Max. travel: 250 mm - Z axis - Adjustment speed: 1000 mm/sec. * Max. travel: 3260 mm - CNC electric motor table crowning - CNC electro-pneumatic die shift (I axis) - WILA / TRUMPF upper tool clamping - hydraulic - WILA / TRUMPF lower tool clamping - hydraulic - 2x front, robust support arms - movable - 1x freely movable 2-hand/foot control - 1x freely movable foot switch - Side safety device (swivel doors) - Rear safety device (sliding doors) - Original operating instructions

Condition: new, turning length 1500 mm turning diameter 560 mm turning diameter over slide 350 mm turning speeds 25-220/220-1500 U/min swing diameter over bed slide 350 mm turning dia. in gap 785 mm quill travel 185 mm spindle bore 105,0 mm engine output 7,5 kW spindle taper DIN 55029 D 1-8 quill: 5 MK weight of the machine ca. 2420 kg. range L-W-H 2840 x 1150 x 1610 mm Equipment: - 3-axis digital display ES-12 V with LCD display - 3-jaw chuck PS3-315 mm / D8 - Fixed steady rest - passage diameter max. 180 mm - Follow-on steady rest - passage diameter max. 120 mm - Foot pedal with brake function according to CE - Protective device for quick-change tool holder - LED machine light - Initial filling with Shell Tellus 46 Bwsdpfx Agsxaau Ej Hon - Clamping disk 450 mm - 2 centering points - Frequency converter - Digital speed display - Slip clutch - Rapid traverse longitudinal and planar - Coolant system - Quick-change tool holder with 4 inserts - Change gears - Reduction sleeve - Chip back wall - Operating tool

Condition: used, Year of construction: 1996, pressure 130 t chamfer lenght 3060 mm distance between columns 2690 mm column arm 410 mm stroke 215 mm dayligth 385 mm Bwedpfoxabqbsx Ag Hjn ajustment speed 200 mm/sec working feed 1-10 mm/sec return speed 135 mm/sec table width 120 mm table height 1050 mm tiltable up to +/- 10 mm Number of working hours 53.820 h compressed air 5.0 - 7.0 bar oil volume 250 l operating pressure 340 bar voltage 400 V total power requirement 16.0 KVA weight of the machine ca. 11250 kg range L-W-H 3640 x 2210 x 2375 mm - in checked condition - machine video - ?v=23IbxRaZ2KA Equipment: - CNC electro-hydraulic press brake - including DELEM CNC control model DA 65 * swiveling control panel, front left * 2D graphic programming & product display * tool & program library * including new TFT-LCD industrial monitor - CNC controlled axes: Y1 + Y2 / X / R - CNC electro-motor / controlled back stop (X axis) - CNC electro-motor / controlled height adjustment (R axis) - manual adjustment of the 2x stop fingers, from the front (Z axes) - manual adjustment of the die displacement, from the front (I axis) - WILA manual table crowning, including analog value display - TRUMPF hydraulic upper tool clamp - TRUMPF manual lower tool clamp - 1x freely movable 2 hand / foot control - Safety device at the rear (sliding door) - Safety device at the side (swinging door) - Original operating instructions + CE declaration + circuit diagram

Condition: used, Year of construction: 1997, pressure 130 t chamfer lenght 3060 mm distance between columns 2690 mm column arm 410 mm stroke 365 mm dayligth 535 mm ajustment speed 200 mm/sec working feed 1.0 - 10.0 mm/sec return speed 135 mm/sec table width 120 mm table height 1050 mm tiltable up to +/- 10.0 mm Number of working hours ca. 31.800 h compressed air 5.0 - 7.0 bar oil volume 250 l operating pressure 340 bar Bjdsxacfmspfx Ag Hewn voltage 400 V total power requirement 23.0 KVA weight of the machine ca. 12950 kg range L-W-H 3660 x 2310 x 2900 mm Machine in a well-maintained condition (!!) with only approx. 31.800 operating hours - in checked condition - machine video - ?v=PBV-MDtZnlE Equipment: - CNC electro-hydraulic press brake - DELEM CNC control model DA 65 * swiveling control panel, front left * 2D graphic programming & product display * Tool & program library * USB keyboard and mouse interface - CNC controlled axes: Y1 + Y2 / X1 + X2 / R1 + R2 / Z1 + Z2 / I axis - CNC controlled back stop (X1 + X2 axis) - CNC controlled height adjustment of the back stop (R1 + R2 axis) - CNC controlled adjustment of the stop fingers (Z1 + Z2 axis) - CNC controlled, pneumatic die displacement (I axis) - CNC WILA electro-motoric table crowning - TRUMPF hydraulic upper tool clamping - TRUMPF manuel Lower tool clamp - 1x freely movable 2-hand / foot control - Safety device at the rear (sliding door) - Safety device at the side (swinging door) - Original operating instructions + spare parts list

Condition: new, turning length 1500 mm turning diameter 410 mm swing diameter over bed slide 255 mm turning dia. in gap 580 mm spindle bore 52,0 mm turning speeds 30 - 3000 U/min bed width 250 mm spindle taper 55029 D 1-6 taper in tailstock 4 MK quill travel 120 mm total power requirement 5,5 kW weight of the machine ca. 1400 kg. range L-W-H 2530 x 1000 x 1450 mm Scope of delivery - 3-axis digital display ES-12 V with LCD display - 3-jaw steel chuck PO3-200 mm / D6 - Clamping disk 350 mm - Fixed steady rest - passage diameter max. 135 mm - Follow-on steady rest - passage diameter max. 65 mm Bjdpfx Agexaalde Hewn - Foot pedal with brake function according to CE - Quadruple tool holder - Protective device for quadruple tool holder - Micrometer longitudinal stop - Turret stop with fine adjustment - Frequency converter - Initial filling with Shell Tellus 46 - Coolant system - Slip clutch - Thread gauge - LED machine light - Change gears - Reducing sleeve - 2 centering points - Chip back wall - Operating tool * Images show identical machine

Condition: new, Year of construction: 2022, HOLZKRAFT Raw Air Extractor ASA 7703 Mobile chip extraction system with a rotating extraction unit and four extraction nozzles (Ø 100 / 120 mm) for milling, planing, and sawdust (not for dust) Nominal flow rate: 7,700 m³/h Extraction nozzle outlet: 1 x Ø 100 | 3 x 120 mm Extraction nozzle inlet: 1 x Ø 260 mm Vacuum pressure: max. 2,800 Pa Filter area: approx. 11.96 m² (2 x 5.98 m²) Chip bag volume: 2 x 290 liters Power consumption: 4.8 kW | 400 V - 50 Hz Bwedpowhui Asfx Ag Hon Idle speed: 2,950 rpm Sound pressure level: max. 98.3 dB(A) Dimensions (L x W x H): 1,900 x 670 x 2,800 mm Net weight: approx. 88 kg Includes 2 fine filter bags and 2 chip bags Availability: Short-term Storage location: Flörsheim

Condition: new, Year of construction: 2022, HOLZKRAFT Raw Air Extractor ASA 7703 Mobile chip extraction system with a rotating extraction unit and four extraction nozzles (Ø 100 / 120 mm) for milling, planing, and sawdust (not for dust) Nominal flow rate: 7,700 m³/h Extraction nozzle outlet: 1 x Ø 100 | 3 x 120 mm Extraction nozzle inlet: 1 x Ø 260 mm Vacuum pressure: max. 2,800 Pa Bwedpfx Aewhui Njg Hen Filter area: approx. 11.96 m² (2 x 5.98 m²) Chip bag volume: 2 x 290 liters Power consumption: 4.8 kW | 400 V - 50 Hz Idle speed: 2,950 rpm Sound pressure level: max. 98.3 dB(A) Dimensions (L x W x H): 1,900 x 670 x 2,800 mm Net weight: approx. 88 kg Includes 2 fine filter bags and 2 chip bags Availability: Short-term Storage location: Flörsheim

Condition: new, Year of construction: 2021, Exhibition unit Year of manufacture: 2021 Dimensions and Weights Length (product): approx. 1700 mm Width/Depth (product): approx. 600 mm Height (product): approx. 2400 mm Weight (net): approx. 69 kg Chip collection volume: 2 x 215 l Nominal outside diameter extraction nozzle (inlet): 260 mm Nominal outside diameter extraction nozzle (outlet): 2 x 100, 2 x 120 mm Electrical Data No-load speed: 2950 rpm Bwsdpfxsw I Uuwj Ag Hon Connection voltage: 400 V Mains frequency: 50 Hz Power consumption: 3.8 kW Output power: 3 kW Filter Filter area: 2 x 2.4 m² Noise Emission Max. sound pressure level: 89.9 dB(A) Airflow Nominal volumetric flow: 4300 m³/h Max. negative pressure: 2000 Pa SCOPE OF DELIVERY Fine filter bag, two chip collection bags Availability: short-term Storage location: Hochheim

Condition: used, Year of construction: 2012, x-travel 1520 mm y-travel 700 mm z-travel 800 mm control Siemens 828 D Shop Mill table surface area 1600 x 700 mm rapid traverse 30 m/min table load 1,4 t turning speed range 8000 U/min max. torque on the spindle 300 Nm power capacity - milling spindle 19,5 kW no. of tools in the magazine 30 Stück tool taper SK 40 | | weight of the machine ca. 10,0 t Bwodpfxov Nhlzj Ag Hon dimensions 4,4 x 2,3 x 2,9 m Equipment: - Coolant through the spindel - Rigid tapping - Dialog programming Shop Mill - Chip conveyor - external elect. hand wheel