Used Ajax Apollo 200 for sale (16,391)

Condition: excellent (used), CTS Type: TSS-70/130 Water-cooled refrigeration unit For sale is a high-quality thermal shock test chamber by CTS (Clima Temperatur Systeme), model TSS-70/130. This device is designed for performing thermal shock tests and is typically used in industry, research, and quality assurance. Application Areas: - Material testing - Aging tests - Electronics and component testing - Thermal shock and temperature cycling tests Technical Specifications: Type: TSS-70/130 Test volume: 130 liters Temperature range: - Hot chamber: +50°C to +200°C - Cold chamber: -80°C to +100°C Heating rate: approx. 6 K/min from ambient temperature to +180°C Cooling rate: approx. 4 K/min from ambient temperature to -60°C Temperature deviation: - ±1 K over time - ±2 K spatially Temperature change rate: - max. 100 K/min average for shock test mode (no radiant heat) Transfer time between chambers: - ≤ 15 min for -65°C to +200°C with 10 kg ICs Changeover time: - < 10 seconds Electrical Specifications: Connection: 400 V, 3/N, 50 Hz Nominal power: approx. 17.2 kW Nominal current: approx. 29 A Site fuse: 32 A slow-blow Connection: Cekon 32 Refrigeration System: Refrigerant: R404A / R23 Water-cooled, low noise, fully hermetic Features/Equipment: - CTS control panel - Microprocessor-controlled regulation and monitoring system - Programmable operation (up to 100 test programs) - Digital setpoint and actual value display - RS232 interface - 2 free switching channels for external device control - Fault notification via volt-free contact (Loadable up to 30 V DC, 2 A) - EMC tested Technical Construction: - Hot and cold chambers - Transfer basket with spindle drive - Test chamber/transfer basket made of stainless steel (material no. 1.4301) - Stainless steel wire insert basket - Tube port NW 50 with sealing plug - Compressed air connection 1/4" male - Non-pressurized condensate drain R 1/2" female thread - Safety door locking - Lockable door with window Dimensions (according to installation diagram): External dimensions approx.: 2335 x 940 x 1820 mm Installation clearance approx.: 1990 x 940 x 1652 mm Test chamber internal dimensions: height approx. 410 mm, width approx. 480 mm, depth approx. 660 mm Window: 300 x 300 mm Additional Data: Protection class: IP 22 Sound pressure level: < 60 dB(A) Weight: approx. 950 kg Average consumption during test cycle: approx. 8 kWh Important information for your safety as a buyer! The following points are performed on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. If required, refill with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, chambers undergo a documented test run. Condition: used Dcsdpfxoy Hkd Hj Aptol Scope of delivery: see photos (Specifications subject to change and errors excepted.) For further questions, please feel free to contact us by phone.

Condition: used, all stainless steel twin shaft paddle mixer intermeshing mixer Dodpfx Aezlrh Ujptscl useful content : 2.000 L dimensions (l x w x h) : ± 4.100 x 1.500 x 2.700 mm 1 front discharge guard 18 kW

Condition: excellent (used), Year of construction: 2011, operating hours: 361 h, functionality: fully functional, machine/vehicle number: 7428122100001.105, pressure: 6 bar, power: 16,500 kW (22,433.73 HP), temperature: 120 °C, operating temperature: 120 °C, total height: 4,300 mm, total length: 8,700 mm, nominal heat output: 165 kW (224.34 HP), total width: 3,700 mm, tank capacity: 33,500 l, empty load weight: 35,000 kg, We offer this Viessmann VITOMAX 200 hot water boiler in very good condition, manufactured in 2011. It is currently stored and preserved with nitrogen. Manufacturer: Viessmann Model: VITOMAX 200 Dcjdpfjzlc Edox Aptsl Year of manufacture: 2011 Type: hot water boiler Operating hours: 361 If you have any further questions or require additional information, please do not hesitate to send us a message or call us. Ioan Munteanu

Condition: good (used), Mounting plate, scribing plate, measuring plate, measuring table, straightening plate, scribing plate, test plate, inspection plate, precision measuring table Dodpezldm Nsfx Aptjcl -Mounting plate: Test plate with support ribs -Clamping surface: 300 x 200 mm -Sheet thickness: 10 mm -Plate: with supporting ribs -Transport dimensions: 446/200/H74 mm -Weight: 11 kg

Condition: used, Year of construction: 2022, operating hours: 3,242 h, Output: 200 kVA / 157 kW Fuel tank capacity: 585 liters Dcsdpfx Aozrkuaoptsl Operating hours: 3242 h, year of manufacture: 12/2022 Sockets: 125-63-32-16A + DS Residual current circuit breaker, Type B

Condition: good (used), Year of construction: 1985, Mengele Paternoster with 42 Trays Dsdpfx Aezrlmqoptscl High-quality, extremely space-saving vertical carousel storage system (paternoster) from the renowned manufacturer Karl Mengele & Söhne. The system operates on the paternoster principle, delivering stored goods directly to an ergonomic retrieval opening at the push of a button. Perfectly suited for tools, spare parts, small-parts storage, or documents in workshops, warehouses, or archives. Technical specifications at a glance: • Manufacturer: Karl Mengele & Söhne • Model designation: 130-200/12 • Number of trays (shelves): 42 units • Permissible maximum shelf load: 100 kg (per tray) • Permissible maximum total load: 4,200 kg (total load capacity) • Power rating / Output: 3,000 W (3 kW) • Connection: 380 V (three-phase current) / 16 A fuse protection • Permissible imbalance: up to 20% • Year of manufacture: 1985 Dimensions (external): • Height: 4,900 mm • Width: 2,660 mm • Depth: 1,300 mm The unit is in good, fully functional condition commensurate with its age. "Everything from a single source: We would be happy to offer you suitable bank financing for your project." komplett-konzept.leasingo.de You can find more storage lifts—both new and used—in our shop! International shipping costs available upon request!

Condition: excellent (used), Year of construction: 2020, operating hours: 19,409 h, functionality: fully functional, number of ink cartridges: 8, color channels: CMYK + Primer + Clear + White + White, number of print heads: 2, resolution (max.): 1,200 dpi, paper width (max.): 2,500 mm, paper height (max.): 1,300 mm, total length: 4,400 mm, total width: 2,450 mm, total height: 1,250 mm, counter reading (black): 3,023, year of last overhaul: 2026, type of input current: three-phase, input current: 16 A, input voltage: 400 V, Mimaki JFX200-2513 UV-LED Flatbed Printer (Model 2020) Professional UV-LED flatbed printer from a single owner – in top condition & serviced annually by a specialist company. For sale is a well-maintained Mimaki JFX200-2513 UV-LED flatbed printer from 2020. The machine comes from a single owner and has only been used in a professional environment. It was exclusively used to print on glass using printing stencils. Dcjdjzt Dmrjpfx Aptsl To guarantee maximum operational reliability and perfect print quality, the system has been serviced annually by the renowned specialist company ESC. All print heads are in good condition (see nozzle test). The last check, including the replacement of wear parts, was carried out by a specialist company in July. Technical data & operating hours (values read from the interface): Printing area: 2,500 mm x 1,300 mm (up to 50 mm media height) Operating hours (Use Time): 19,409 h Printed length: Print Length: Only 3,023 m, Print Area is currently only 5142m² UV lamps (LED): 2 UV-LED lamps (Note: Extremely long-lasting UV-LED technology) Printing area: 2,500 mm x 1,300 mm (up to 50 mm media height) Ink configuration & special features: Ink type: Mimaki LUS-120 (Excellent adhesion and flexibility on rigid and flexible media) Color configuration: CMYK + Primer + Clear (Varnish) + White + White Your advantage: The double white configuration provides extremely high opacity and speed when printing undercoat or overcoat. The integrated primer and clear varnish enable smart finishing options (spot varnish/textures) and printing on demanding materials such as glass, metal, or acrylic. Accessories & highlights included in the scope of supply: Including a powerful suction fan (vacuum add-on): Keeps even uneven or lightweight sheet materials perfectly flat on the printing table. Transport securing device available: The original transport securing device for safe shipping is fully available. Location & removal: Easy logistics: The hall has a large roller shutter door, which makes the removal for a specialist shipping company or a service company easy and straightforward on the ground floor. Inspection and test print can be arranged at the location. Price is net, plus VAT. Errors and prior sale reserved. This offer is exclusively aimed at commercial businesses and freelancers.

Condition: excellent (used), Year of construction: 2006, clamping force: 500 kN, screw diameter: 22 mm, clearance between the columns: 355 mm, overall weight: 2,700 kg, Clamping force: 50 t Year of manufacture: 2006 Injection unit .../200 Screw diameter: 22 mm Specific injection pressure: 2800 bar Injection volume: 41.8 ccm Mould clamping system 50/... Clamping force: 50 t Mould plate dimensions: 520 x 520 mm Tie bar clearance: 355 x 355 mm Dodpfx Aozt Ih Tsptscl Mould height: 210 mm Opening stroke: 400 mm Maximum platen distance: 610 mm Weight: 2700 kg Dimensions (m) L x W x H: 3.8 x 1.1 x 2.1 m Control: NC4

Condition: good (used), Cutter head, milling chuck, carbide cutter, indexable insert cutter, face milling head, milling head, cutter head shell cutter, face milling cutter, corner milling cutter -Face milling cutter: cutter head -Type: UER 200-1-12 -Mount: Ø 60 mm / Bolt circle Ø 102 x 18 mm Dsdszqyw Iopfx Aptscl -Dimensions: Ø 200 x 62 mm -Weight: 8.7 kg

Condition: used, Year of construction: 2004, functionality: fully functional, turning length: 307 mm, turning diameter: 250 mm, spindle bore: 51 mm, travel distance X-axis: 185 mm, travel distance Z-axis: 370 mm, Key figures at a glance: 250 mm maximum turning diameter, 420 mm swing over bed, 307 mm maximum turning length, 51 mm spindle bore, 4000 rpm maximum spindle speed, 5.5/7.5 kW main motor, an 8-station turret, Dcjdpfx Aozr Ir Ajptol 185 mm X-axis travel and 370 mm Z-axis travel. The year of manufacture is 2004 and the control system is a Fanuc Series 21i-TB. The machine plate states a supply of 220 V, three phase, 50/60 Hz, 42 A and a maximum power supply of 16.1 kVA, with control voltages of 100 V AC and 24 V DC. Buyers on a 400 V network should plan for a matching transformer. The approximate footprint is 1600 x 1280 x 1890 mm at a weight of around 2800 kg

Condition: ready for operation (used), Year of construction: 2004, Pack press Signode with plastic strapping Dcjdpfx Ajzca Uxjptel

Condition: used, mileage: 3,547 km, gearing type: other, fuel type: electric, color: red, first registration: 08/2016, emission class: none, suspension: other, Year of construction: 2016, operating hours: 3,547 h, driver cabin: other, fuel: electricity, For sale is a BT LPE 200/8 in red, first registered in August 2016. Dodpfxezvhyhs Aptjcl With only 1,728 km on the odometer, the vehicle is in very good, well-maintained condition and is ready for immediate use. The BT LPE 200/8 impresses with its reliable technology and easy operation – ideal for warehouses, industrial facilities, or logistics companies. Sale only to commercial businesses (agriculture, freelancers, small and large businesses) or for export. Subject to errors and prior sale.

Condition: used, mileage: 2,511 km, gearing type: other, fuel type: electric, color: red, first registration: 08/2016, emission class: none, suspension: other, Year of construction: 2016, operating hours: 2,511 h, driver cabin: other, fuel: electricity, For sale is a BT LPE 200/8 in red, first registered in August 2016. With 2,540 km on the odometer, the vehicle is in very good, well-maintained condition and is ready for immediate use. The BT LPE 200/8 impresses with its reliable technology and easy operation – ideal for warehouses, industrial facilities, or logistics companies. Dsdpfx Aozvhyneptscl Sale only to commercial businesses (agriculture, freelancers, small and large businesses) or for export. Subject to errors and prior sale.

Condition: new, new ! all stainless steel closed lid with seal 2 mixing directions (manual or automatic) tiltable CE-approved power : 2,2 kW overall dimensions (l x w x h) : ± 1.300 x 600 x 1.300 mm The Barmix 200 liter paddle mixer is an ideal machine for mixing all types of food products within the meat, poultry, fish, vegetables, dairy, cereal, confectionery, petfood and sandwich filling industry. Mixing for meat and vegetarian burgers, sausages, meatballs, coleslaw, potato salad and other wet salads, mash potato, vegetables fresh and frozen, cereals, raw petfood Also suitable for dry products, such as herbs, ingredients, powders, granules, nuts, grains, seeds, kernels, dried fruit, Granola, etc. Djdpfxezi Sdqe Aptjcl

Condition: excellent (used), Sanding belt width: 200 mm Sanding belt length: 1800 mm Table surface area: 230 x 600 mm Djdpfxszi A Sls Aptjcl 5 sanding speeds via stepped pulley drive Electrical connection: 400 V, 0.55 kW

Condition: excellent (used), Espec Type: TSA-202E-W Temperature shock chamber, water-cooled Cold chamber: -55°C to 0°C Hot chamber: +50°C to 200°C System: Two-zone testing via damper control Temperature fluctuation: ±0.5°C Dedpjzh Htksfx Aptecl Hot chamber: Temperature: Heating time: from ambient temperature (20°C) to +200°C within 15 minutes. Cold chamber: Temperature: Cooling time: from ambient temperature (20°C) to -55°C within 35 minutes. Temperature: Recovery time: within 5 minutes. Internal dimensions (W x H x D mm): 650 x 460 x 670 External dimensions (W x H x D mm): 1550 x 1900 x 1670 Approx. 200 liters Power supply: 400 V AC 50Hz: 65 A Refrigerant: R404A 5 kg, R23 2.0 kg Weight: approx. 1200 kg For your safety as a buyer, please note the following information: The following points are carried out on our offered chambers in advance: 1. Functional check and replacement of necessary components 2. If necessary, refilling with legally compliant refrigerant 3. Leak test with certificate 4. After successful inspection, the chambers are subjected to a documented test run. Condition: used Scope of supply: (See picture) (Changes and errors in the technical data are subject to change!) We will gladly answer any further questions you may have by phone.

Year of construction: 2019, condition: ready for operation (used), Ulma weighing and packing line Complete weighing and packaging line with an Ulma multi-head weigher and an Ulma vertical bagger. This line consists of the following machinery: 1. Infeed conveyor belt; 2. Ulma multi-head weigher; 3. Ulma VTI 200 vertical bagger; Dcjdpfx Aezvc Dzsptol 4. Outfeed conveyor belt; 5. Platform; 6. Stair; Ulma Multi-Head Weigher Manufacturer: Ulma Year: 2019 Max. weighing speed: 30 bags/minute Number of heads: 10 Volume of heads: 2.5 liters Max. weighing range: 5,000 grams Power: 400V / 50Hz / 1kW Ulma VTI 200 Vertical Bagger The VTI 200 machine has been specifically designed for the packaging of a wide range of different product types and focuses on markets where the main requirements are simplicity, reliability, and ease of operation. The combination of pneumatic operation of the horizontal sealer and an AC motor for the draw-down belts provides the machine with great versatility for use in many different environments. The robustness of all mechanical and electrical parts, a compact design, and ease of operation, together with low maintenance requirements, make it the ideal competitively priced machine for intermediate-speed applications. The machine is operated via a 5" color touch screen with an integrated industrial PC. All machine parameters are adjusted and saved within this interface, resulting in a very flexible and quick changeover machine. Manufacturer: Ulma Model: VTI 200 Year: 2019 Capacity: Max. 70 bags/minute Film reel width max.: 600 mm Film reel outer max.: 450 mm Film reel core max.: 76 mm Power: 400V / 50Hz / 4kW The machine is equipped with the following tool: Bag Type: Pillow bag; Bag dimensions: BOPP L x W 145x145mm / Laminate L x W 170x170mm Foil width: BOPP 310mm / Laminate 365mm; Max product dimensions: 70mm

Condition: used, mileage: 12,850 km, power: 90 kW (122.37 HP), first registration: 05/2025, fuel type: electric, overall weight: 2,550 kg, fuel: electricity, color: black, gearing type: automatic, suspension: steel, number of seats: 5, Equipment: ABS, air conditioning, airbag, central locking, cruise control, immobilizer system, navigation system, onboard computer, parking sensors, power assisted steering, seat heater, sliding door, traction control, E07 Hill-start assist, F2W Winter package, EY5 Mercedes-Benz emergency call system, SD1 i-Size child seat mounting, EY6 Breakdown assistance, B25 Parking brake, electric, EI0 Wireless charging system for mobile devices, T68 Child safety lock for doors and windows in the passenger compartment, Z1M Approval M1, IA0 Wheel formula 4x2, LG7 LED High Performance headlights, XO7 Mercedes-Benz Mobilo with breakdown assistance and extended warranty, EZ7 Active parking assist, R2H 40.6 cm (16) light alloy wheels in multi-spoke design, T78 Sliding door rail cover in vehicle color, Y10 First-aid kit, 804 AEJ X3/1, VL2 Velour floor mats, SF6 Driver's seat, height-adjustable with lumbar support, RD9 Tires without specified manufacturer, H00 Warm air duct to the passenger compartment, NM5 MB-NA 60 2b with flange, low mounting, M-engine speed, C6L Multifunction steering wheel, H10 Seat heating for driver and front passenger, H22 Heated rear window, EM7 2 USB ports in the center console at the rear, Y44 Warning triangle, GA2 Automatic transmission for electric drive, P2F Active safety package, FP3 Mirror package, FP4 Chrome interior package, XC8 VIN visible from the outside, SZ6 Table and illuminated trim elements on the backrest, Z6L Progressive, JH3 Communication module (LTE) for digital services, X30 Vehicle registration certificate, part II, X2W Weight variant 2,550 kg, FQ3 Glove compartment, passenger side, closed, I5T Underbody protection, plastic, RY2 Tire pressure monitoring system on front and rear axle, wireless, CK4 Handle strip above license plate in vehicle color, 054 AEJ X3/2, CK8 Heated steering wheel, XU1 Labels / printed materials in German, IG4 Standard, SK5 Automatic front passenger airbag deactivation, I6I With seat belt, center seat in the rear, W29 Fixed rear windows, CL1 Steering wheel adjustable in inclination and height, CL3 Leather steering wheel, FR8 Rear, We are available by phone Monday - Friday until 8:00 PM and Saturday until 4:00 PM!! Furthermore:!! Leasing/financing and trade-in possible!! Dcedpfezqt T Aox Aptsl !! !! -Errors and prior sale excepted!! -All information without guarantee ... more on our homepage

Condition: used, Year of construction: 2010, turning length: 1,495 mm, spindle speed (min.): 35 rpm, spindle speed (max.): 5,000 rpm, spindle bore: 65 mm, travel distance X-axis: 580 mm, travel distance Y-axis: 160 mm, travel distance Z-axis: 1,545 mm, workpiece weight (max.): 300 kg, total height: 2,577 mm, total length: 5,088 mm, total width: 2,450 mm, spindle nose: A2-6, spindle diameter: 660 mm, Equipment: documentation/manual, CNC Control Mazatrol Matrix Turning diameter 660 / 260 mm Turning length 1495 mm Spindle bore diameter 65 mm Spindle nose A2-6 Spindle nose sub spindle A2-6 Turning speed spindle 35 - 5.000 R/min Turning speed sub spindle 35 - 5.500 R/min Milling head speed 15 - 21.500 R/min Movement X-axis 580 mm Movement Y-axis 160 mm Movement Z-axis 1.545 mm B-axis travel 225° C-axis indexing 0,0001 (360) ° Tool taper Capto C6 Tools in tool magazine 120 Barfeeder Irco-Breuning ILS-MUK Dcjdpfx Apozqt Umotsl If you have any questions concerning the machine, please do not hesitate to contact us by phone or e-mail. Feel free to view our other advertisements for a complete overview of our stock.

Condition: refurbished (used), Year of construction: 1990, Drum chipper / chipping machine / wood shredder Dcjdpfx Aszq Sqgjptsl fully reconditioned (workshop-reconditioned) Make: Rudnick & Enners Year of manufacture: 1990 Rudnick & Enners drum chipper, type TH-200/650/3 workshop-refurbished (fully reconditioned) with new bearings (spherical roller bearings) and tested rotor New blades and counter-blades Feed width/height: 650 x 200 mm Rotor diameter: 600 mm Screen mesh size: 50 x 50 mm Drive power: 75.0 kW Feed motors: 2 x 3.0 kW Weight: approx. 3,500 kg Machine colour: RAL 6011 Reseda green Without electrical installation and without control cabinet

Condition: used, functionality: fully functional, Year of construction: 1991, Used loading silo Manufacturer: Ulrich Total volume: 200 tons - Bucket conveyor - Hoist winch - Electrical system Dedpfx Apozq S Ewotecl

Condition: used, Bench Grinder REMA DS 12/200 - 1 grind Rotation: 2900 RPM Grinding wheel: Ø 200 mm x 30 mm Dcsdpfx Ajzwgt Nsptel Motor: 0,9 kW Voltage: 380 V Width: 600 mm Depth: 400 mm Total height: 1100 mm Weight: approx 80 KG

Condition: used, Year of construction: 1999, functionality: unexamined, volume flow: 200 m³/h, input voltage: 400 V, input frequency: 50 Hz, type of cooling: air, PVR Vacuum Pump Dcedpfx Ajzwva Sjptsl Type PVL 200 Capacity 200 m³/h Absolute pressure 0.5 mbar Year of manufacture 1999 Price €3,000

Condition: excellent (used), Type: SWT 200/400-S Weiss Spray and Splash Water Test Cabinet Used to test water ingress into enclosures. In combination with a timer, the test cycle can be automated with an adjustable test duration from 3 seconds to 30 hours. Complies with DIN VDE 0470 T1 and EN 60529 for tests according to protection classes IPX3 and IPX4. The integrated recirculation system reduces water consumption to a minimum. Features - Glass door with wiper - Pneumatic drive for the oscillating pipe - Adjustable oscillation angle - Interchangeable oscillating pipes - Swivel and interchangeable nozzle holders - Adjustable and measurable water flow rate - Test duration control Data for mechanical load: - Max. load with test specimens (evenly distributed): Permissible total weight for specimen carrier: 25 kg - Spray radius: 200 mm / 400 mm Data for IP protection class tests - Oscillation speed approx. 60°/s - Oscillation angle IPX3 approx. ±60° - Oscillation angle IPX4 approx. ±180° -10° Dimensions: - External dimensions with control cabinet (D x W x H): approx. 1000 x 1350 x 1900 mm Djdpfozii Akjx Aptjcl - External dimensions (D x W x H): approx. 1000 x 1000 x 1900 mm - Internal dimensions (D x W x H): 400 x 650 x 750 mm Operating data: - Voltage: 3/N/PE AC 400V ±10% 50Hz - Rated power: 1.5 kW - Rated current: 6.0 A - Weight: 375 kg Important note: "The table shown in the photos is not included in the sale." Condition: used Scope of delivery: (See picture) (Technical data subject to change and errors excepted!) Further questions can be answered by phone.

Year of construction: 2023, condition: ready for operation (used), An unused Traub CNC twin-spindle turning and milling center with peripheral equipment is available. Spindle types 1/2: D76/D76, max. turning length: 900mm, max. workpiece diameter: 76mm, number of tool carriers: 3, control system: Traub TX8i-s V8. Main spindle bore: 76mm, taper size: 6, hollow clamping cylinder: D76/20, indexing: 2.5°, clamping pressure range: 8bar-75bar. Counter spindle bore: 76mm, taper size: 6, hollow clamping cylinder: D76/20, indexing: 2.5°, clamping pressure range: 8bar-75bar. Upper tool carrier: axes: X/Y/Z, stations: 12. Lower left tool carrier: axes: X/Y/Z, stations: 12. Lower right tool carrier: axes: X/Y/Z, stations: 12. Including Isi Elbaron RON4DHEC mist extraction and filtration system, custom-built circulation conveyor, Bürener hinged belt chip conveyor, Bürener Eco-Fluid coolant system (600l), cooling unit, coolant chiller, Traub WH workpiece handling system, various grippers and gripper pairs, IoT, and management and monitoring software. This machine was never put into operation and is therefore in as-new condition. Documentation available. An on-site inspection is possible. Dedezkvkqjpfx Aptscl