Used Femia Bean Calibrator for sale (1,139)

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, Equipment: documentation/manual, type plate available, Taylor Hobson Talyrond 265 roundness measuring instrument. Extremely accurate; it can measure the roundness of lenses, optics, pistons, turbine components, tubes, shafts, and also eccentricity, e.g., of cams on a camshaft or journals of a crankshaft. It is certainly of interest for motorsport and tuning companies. Nsdpfszcqy Ejx Ab Usdb The first photo is a "representative image" from a Taylor Hobson catalog, showing how it is constructed, except for the computer, which is a newer, more modern HP model with a small form factor. Max. diameter 350 mm Max. test piece height 500 mm (higher values are possible by measuring in two parts, up to a maximum of 1000 mm...) Self-centering of the workpiece +/- 5 mm Max. weight of test piece 40 kg The system has been used very little and has had only two owners. The first owner, from whom I bought it, was an implant company in Hamburg; it was used in a "medically clean environment" and is extremely clean. It was never located in a dirty machine hall. The year of manufacture is estimated to be between 2003 and 2005. The Taylor-Hobson measurement software is, of course, included and runs on the supplied HP computer (without a password...). It is also on the USB stick, perhaps for installation on another machine at your location. Accessories are included: the original Taylor-Hobson desk, computer, monitor, seven (7!) measuring probes, each of which is very expensive to purchase. A sample/sample lens (hemisphere) is included for calibration! The very detailed operating manual is on the USB stick, and all circuit diagrams and functional diagrams are also included! The system will be shipped on two Euro pallets via a freight carrier. It is already well secured on them. The Talyrond 265 and the desk will be wrapped with bubble wrap, etc., and secured with stretch film to provide extreme protection during transport. The system itself is fixed with "transport safety screws." Shipping is at the buyer's expense and will be on two Euro pallets. The measuring system should definitely be assembled and put into operation by a Taylor Hobson service technician, who can then also recalibrate the system on-site. This is now recommended after a few years. Errors can be made during assembly and commissioning. For example, some locking screws are installed for transport, and if you forget them, the system could be damaged when starting up. A truly well-maintained, very accurate system that will continue to provide excellent service for many years to come!

Condition: refurbished (used), Year of construction: 2026, functionality: fully functional, spindle bore: 90 mm, turning diameter: 630 mm, turning diameter over bed slide: 630 mm, turning diameter over top slide: 380 mm, turning length: 3,000 mm, quill diameter: 90 mm, total length: 4,900 mm, total width: 1,420 mm, total height: 1,590 mm, rotational speed (max.): 1,800 rpm, rotational speed (min.): 18 rpm, overall weight: 3,700 kg, workpiece weight (max.): 1,500 kg, spindle mount: MK 6, The universal lathe FAT TUR 630M/3M has been comprehensively rebuilt and modernized, has technical parameters in accordance with the technical and operational documentation DTR of a new machine, WOT technical acceptance conditions and the Polish Standard and also meets EU requirements. The machine is covered by a full 12-month warranty on spare parts and electrical components. Availability: in stock, under power, ready for technical acceptance. Technical specifications: - distance between centers/turning length: 3000 mm - turning diameter over bed: 630 mm - turning diameter over support: 380 mm - spindle bore diameter: 90 mm - maximum workpiece weight between centers: 1500 kg Nodpfx Ajd Eaa Ejb Uodb - number of spindle speeds: 21 - range of rotational speeds (rpm): 18 - 1800 - range of feeds (mm/rev): longitudinal: 0.05 – 3,26 transverse: 0.25 – 1,63 - engine power: 15 kW - overall dimensions: total length: 4900 mm width: 1420 mm height: 1500 mm total weight: 3650 kg Standard equipment: tailstock, coolant pump, tool post, chuck cover Additional equipment available at extra charge: - 3- or 4-jaw chucks, various diameters and variants - Digital readout on 2 axes with assembly and calibration - Steady rest, 10-140 mm, with rollers - Steady rest, 10-180 mm, with rollers - Steady rest, 140-300 mm, with rollers - MULTIFIX quick change tool post

Condition: new, Turbocharger core balancing machine DBST-20 Nedsn Nxcfopfx Ab Ujdb Low-speed turbocharger core balancing machine meets the needs of turbocharger repair workshops. Machine is used for balancing common truck and passenger car turbos. It is multi-functional and universal, so it is suitable for many large turbochargers of special vehicles, railroad and marine turbines, and even for industrial turbochargers of gas and diesel power plants. The DBST-20 is used for balancing common truck and car turbochargers. It is multifunctional and universal, so it is suitable for many large turbochargers of special vehicles, railway and marine turbines, and even industrial turbochargers of gas and diesel power plants. This stand allows for the final balancing of cartridges due to the specific design features of large turbines. The stand is used for balancing turbocharger cartridges at low speeds, as well as for checking turbocharger cartridge oil leaks. This is a larger version of the DBST-10 model that our company has developed specifically for large turbochargers weighing up to 30 kg. HIGHLIGHTS High accuracy of determining the unbalance of the rotor (0.4 g ∙ mm / kg). Reinforced torsional vibration suspension - high accuracy of vibration transmission, quality balancing results. Mounting the cartridges on their standard surfaces (as on the engine) allows the installation of almost all turbochargers. Wide range of accessories and adapters for installing any kind of turbos. Includes adapters for installing turbochargers with lower oil inlet. Oil system with oil heating allows to recreate similar conditions to the real one during balancing. 3-stage system of oil filtration allows to eliminate an unbalance directly on the machine by portable grinders. The measuring system displays the balancing process in real time and monitors the rotor unbalance behaviour on the screen to achieve the best possible result. Rotor adjustment and machine calibration are performed by the operator, ensuring maximum machine sensitivity at all times. Safe turbo shaft speed allows risk-free quality running-in of assembled cartridges, which significantly increases cartridge reliability after repair. KEY FEATURES • High accuracy 2 plane balancing • Truck and car turbocharger balancing • Any turbocharger can be installed • All type turbocharger adapters included • Quick and easy turbo core installation • Balancing speed up to 10 000 rpm • Fast oil heater and temperature regulation • 3-stage oil filtration • Real-time unbalance measurement • Calibration of the machine by the operator • Industrial fanless touch screen PC control system • Creation and printing of reports on turbocharger balancing SPECIFICATIONS Maximum turbocharger weight 30 kg Maximum turbocharger diameter 300 mm Maximum turbocharger length 300 mm Maximum rotation speed 10 000 rpm Minimum achievable residual specific imbalance, 0,4 g mm/kg Pneumatic system operating pressure 0,6 – 0,8 MPa Power supply 220V, 1Ph, 50Hz Power input 1,5 kW Dimensions 1120 х 780 х 1350 mm Weight 285 kg

Condition: new, workpiece weight (max.): 30 kg, rotor diameter: 700 mm, The BALANCING MACHINE 9A713 is a universal horizontal-axis balancing machine designed for light rotors up to 30 kg in various configurations. This series incorporates innovative technical solutions, ensuring that balancing is straightforward and accessible. With high performance and functionality, the 9A713 is popular in manufacturing across multiple industries. Originally designed for small series and individual production, its versatility and productivity have also made it a favorite in various repair shops. HIGHLIGHTS • High balancing accuracy 0,4 gmm/kg = 0,4 µm • Advanced Rollers: Specially designed rollers with advanced grinding technology mounted on precision bearings. • Bearing Design Options: Hard-bearing design suitable for small rotors, with optional soft bearing support available. • Belt Drive System: High degree of belt tensioning repeatability with a micro-tuning function for precise belt tension adjustment. • Quick Changeovers: Easy access to support rollers for quick rotor reinstallation and rapid replacement of roller units with prism units, significantly reducing changeover time. • Versatile Rotor Balancing: Capable of balancing rotors with small distances between bearing journals, limited only by the drive belt width. • Variable Speed Control: Frequency inverter asynchronous electric drive with a powerful motor for infinitely variable speed control and smooth acceleration/deceleration. • Height-Adjustable Supports: Adjustable supports to accommodate different bearing journal diameters, aiding in centering the workpiece. • Easy Installation: Requires no special foundation and can be installed on a standard concrete floor. MEASUREMENT AND CONTROL • We make balancing easier - the main advantage of our balancing systems. • The balancing process is displayed in real time and the unbalance behaviour of the rotor is monitored on the screen to achieve the best possible result. • The maximum sensitivity of the machine at any moment of operation, the set-up and calibration of the machine is carried out by the operator himself. • Free from the influence of external vibration factors on the measurement result, it has a high degree of protection against various types of interference. • Easy to learn working skills and maintenance for any employee. SPECIFICATIONS Weight range of balanced rotors 0.3 - 30 kg (60 kg) Maximum rotor diameter (above the bedding) 700 mm Distance between centres of rotor supports 10 – 700 mm Support type Rollers + Prisms Transmission element for rotor rotation Belt Minimum achievable residual specific unbalance 0.4 g*mm/kg Rotor speed range 300 – 2000 rpm Electric motor power 0.75 kW Parameters of the supply network 380V, 3 Ph, 50Hz Ndjdpjtu Ukaefx Ab Ujb Do you need a machine for a different load capacity, diameter or length? We manufacture balancing machines for every needs. Please contact us to get the best offer! 👇

Condition: excellent (used), Year of construction: 2013, functionality: fully functional, measuring range X-axis: 500 mm, measuring range Y-axis: 400 mm, measuring range Z-axis: 400 mm, Equipment: type plate available, Mitutoyo coordinate measuring machine, type Crysta Apex S544 Multi-sensor cabling (analog scanning) Temperature compensation for all axes Measuring range, X-axis = 500mm Measuring range, Y-axis = 400mm Measuring range, Z-axis = 400mm Measurement uncertainty = 1.7 + 3L/1000 (µm) Mitutoyo controller UC200H Renishaw probe head PH6M Njdpfxjzhumfs Ab Ujdb Renishaw sensor SP25M Renishaw module SM25-1 Measuring software MCosmos-1 v.4.x PC system WIN10 and 27" monitor (new) Reference sphere / calibration sphere (new) Hardware & software upgrades available upon request Delivery & other services available upon request

Condition: used, functionality: fully functional, measuring range X-axis: 700 mm, measuring range Y-axis: 700 mm, measuring range Z-axis: 600 mm, Equipment: type plate available, Mitutoyo coordinate measuring machine type Crysta Apex C776 Temperature compensation on all axes Measuring range X-axis = 700 mm Measuring range Y-axis = 700 mm Ndodpfxswhfh Ao Ab Ujb Measuring range Z-axis = 600 mm Measurement uncertainty = 1.9 + 3L/1000 (µm) Renishaw probe head PH10MQ Renishaw change rack SCR200 Renishaw sensor TP200 Renishaw TP200 modules = 6 pcs Measuring software MCosmos PC system WIN10, 27" monitor Reference sphere / calibration sphere Software upgrade optional Hardware upgrade optional Full service upon request

Condition: used, functionality: fully functional, measuring range X-axis: 700 mm, measuring range Y-axis: 1,000 mm, measuring range Z-axis: 600 mm, Equipment: type plate available, Mitutoyo Crysta Apex C7106 coordinate measuring machine Temperature compensation on all axes Njdpfx Ajwhb A Nob Ujdb Active vibration isolation system from BILZ X-axis measuring range = 700 mm Y-axis measuring range = 1000 mm Z-axis measuring range = 600 mm Measurement uncertainty = 1.9 + 3L/1000 (µm) Renishaw PH10MQ probe head Renishaw SCR200 interchangeable rack Renishaw TP200 sensor Renishaw TP200 modules = 6 units MCosmos measuring software WIN10 PC system, 27" monitor Reference sphere / calibration sphere Optional software upgrade Optional hardware upgrade Full service available upon request

Condition: ready for operation (used), Year of construction: 2013, operating hours: 7,358 h, functionality: fully functional, machine/vehicle number: 6LUD00036, travel distance X-axis: 620 mm, travel distance Y-axis: 520 mm, travel distance Z-axis: 460 mm, feed length X-axis: 620 mm, feed length Y-axis: 620 mm, feed length Z-axis: 460 mm, feed rate X-axis: 36,000 m/min, feed rate Y-axis: 36,000 m/min, feed rate Z-axis: 36,000 m/min, torque: 108 Nm, controller manufacturer: Heidenhain, controller model: iTNC530, workpiece length (max.): 500 mm, workpiece width (max.): 400 mm, workpiece height (max.): 350 mm, workpiece diameter (max.): 680 mm, workpiece weight (max.): 300 kg, total height: 3,400 mm, total length: 4,600 mm, total width: 2,700 mm, table width: 600 mm, table height: 755 mm, table length: 600 mm, table load: 300 kg, rotary table diameter: 600 mm, rotational speed (min.): 20 rpm, rotational speed (max.): 12,000 rpm, overall weight: 8,500 kg, spindle speed (min.): 20 rpm, spindle speed (max.): 12,000 rpm, operating hours of spindle: 5,303 h, coolant supply: 18 bar, distance table center to spindle nose: 50 mm, spindle motor power: 17,000 W, spindle nose: SK40, number of spindles: 1, number of slots in tool magazine: 100, input voltage: 400 V, type of input current: three-phase, Equipment: chip conveyor, documentation/manual, Commissioned 4/2014 Table rotation, C-axis: 360° Table swivel, B-axis: -50° to +110° Distance from spindle nose to table: 150 mm Table clamping surface: Ø 650 Table load capacity, max.: 300 kg Table slots: 5 x 18H7 x 100 mm Centering bore: Ø 50 H7 x 30 mm Workpiece size, max.: Ø 520 x 330 mm Machine accuracy: VDI I DGQ 3441* Positioning accuracy: +/- 0.006 mm* Axis resolution: 0.001 mm* *determined at a constant ambient temperature of 20°C +/- 1°C Main spindle: Main drive, AC motor, direct drive Drive power (100% / 25% ED): 10.0 / 17.0 kW Speed range, stepless: 20 - 12000 rpm Spindle taper: SK 40 DIN 69871 Torque at (100% / ED): 63.7 / 108.6 Nm Axis drives: Axes X, Y, Z: AC motors Axes B, C: AC motors Travel speeds: Rapid traverse in axes X, Y, Z: 36 m/min Speed, max. B-axis: 25 rpm Speed, max. C-axis: 25 rpm Acceleration X, Y, Z: 6.5 m/s² Coolant system: External tool cooling via external nozzles Coolant tank: 280 l Operating pressure, external: 0.9 bar Coolant system, internal tool cooling DIN 69871 Form A Operating pressure, internal coolant supply: 18.0 bar Manual rinsing of the work area via an additional gun Standard accessories: Ndodjz Diq Uepfx Ab Uob - CNC control: Heidenhain iTNC 530, full simultaneous 5-axis version - Handwheel 410 (Heidenhain) - Digital axis drives - Digital spindle drive - Swarf conveyor with discharge height 800 mm • Spindle cooling – radiators – plate cooling for spindle motor - Full protective enclosure with cabin roof Tool magazine VZG 65 5A by Indunorm: Number of tools: 100, with a tool length of up to 320 mm / can be converted to 125 tools, then a tool length of only 200 mm is possible. Tool diameter, max.: 80 mm Tool diameter, max.: 130 mm (with free adjacent positions) Tool change with double gripper - Linear path measuring system in axes X / Y / Z (glass scale) - Direct encoder in axes B / C - Temperature compensation - IR measuring probe – 3D Software - Option - iTNC 530 Kinematic-Opt • Calibration software Internal tool cooling 18 bar • Coolant tank • Internal tool cooling: 280 L DIN 69871 Form A • Double-circuit filter • Switchable filter cartridges • Filtration rate: 10 µm Band filter system PRODUCTION - LINE - RT 100 Automatic pallet changing system Loading and unloading via a linear axis system: Handling data: Handling weight, max.: 100 kg (35 kg) Pallet capacity: 6 pallet positions up to 400 x 400 mm: Control: PLC control with integrated control cabinet incl. switching and control components incl. software for the automatic sequence Zero point clamping system 320 x 320 x 60 mm - Clamping via 4 clamping bolts - Axis distance: 180 mm - Clamping force: 4 x 12500 N - Repeatability: 0.005 mm - Axial load, max.: 4000 kg • Zero point clamping plate 320 x 320 - Automatic door Interface for automation and clamping systems Universal interface for automatic pallet changing systems, force clamping devices and zero point clamping systems • for pneumatic clamping systems • 2-channel rotary feedthrough integrated in the table • Pneumatic lines led to the outside • Pneumatic maintenance unit • Control via M commands logical inputs and outputs prepared incl. 7 pallets 320x320 with 6 vices and one 3-jaw chuck !!without tool holders and without tools!! Machine ex works, without delivery and assembly, all information without guarantee, price plus statutory value-added tax.

Condition: good (used), Rolong Hydraulic Book Spine Calibration Press This machine is used to calibrate the spines of book blocks or brochures. After calibrating the spine, its thickness is equal to the thickness of the block in the groove. This process is performed after the books have been sewn. Ndjdpfezt H T Iex Ab Uob 380V power supply Manufacturer: Gantenbein, Switzerland

Year of construction: 2023, operating hours: 4,371 h, condition: ready for operation (used), travel distance X-axis: 460 mm, travel distance Y-axis: 320 mm, travel distance Z-axis: 660 mm, spindle motor power: 11,500 W, spindle speed (max.): 10,500 rpm, number of axes: 5, This 5-axis WALTER HELITRONIC RAPTOR DIAMOND was manufactured in 2023. It features a tool diameter capacity of Ø3-290 mm, with an optional extension up to Ø400 mm, and a maximum tool length of 270 mm. The machine is designed for the production and regrinding of carbide, HSS, PCD, and CBN tools. If you are looking to get high-quality grinding capabilities, consider the WALTER HELITRONIC RAPTOR DIAMOND cylindrical grinding machine we have for sale. Contact us for further details. • Operating hours: approx. 4,371 h • Working range: • Tool diameter: Ø3–290 mm (optional up to Ø400 mm, depending on configuration) • Maximum tool length: 270 mm (optional up to 350 mm, depending on configuration) • Maximum tool weight: 50 kg • Axes: • Number of CNC axes: 5 • Linear axis speed: up to 15 m/min • Spindle: • Max grinding wheel diameter: Ø200 mm • Interface: HSK • Belt-driven, double-ended spindle • Grinding / Eroding: • Grinding and EDM in one setup • For carbide, HSS, PCD, CBN tools • Configurable for up to 3 electrodes and 3 grinding wheels, or alternatively up to 6 grinding wheels • Control / Machine design: • WALTER / UNITED GRINDING CNC control • Enclosed working area with automatic protective door • Installed machine options/features: • Upper table • Glass scales • Reinforced A-axis, up to 750 rpm • Preparation for automatic calibration/probe • Grinding wheel measuring probe • Automatic fire suppression system with leak detection • TS-Remote Ready • Keyboard support • Oil leak sensor • Connection for external filtration system Additional equipment • Automatic loading/manipulator system for shank tools (automatic tool loader/manipulator) • Process cooling system • Coolant/dielectric filtration and circulation system • Coolant/dielectric system • Tool holders • Flanges/adapters • Grinding wheel/electrode accessories • Automation/handling: • TOP loader • 12 pallets • Filtration/cooling/extraction: • Oil mist extraction system • Extraction silencer Ndedpfx Abszxg Tfj Ueb • Oil cooling unit • Filtration system with tank and pump • Workholding/tooling: • Collets 6–16 mm • Collets 16–32 mm • 351 ES collets: 6, 8, 10, 12, 16 mm • 4 x 351 ES collet sets • Collets: 6, 8, 10, 12, 14, 16, 18, 20, 25 mm • Automatic holder 6–16 mm • Automatic E386 holder, 16–27 mm • Manual hydraulic holder, diameter 32 mm • ISO 50 socket • ISO 50 arbor • 2 x 50 mm HSK electrode holders • 4 x 45 mm HSK grinding wheel holders • Grinding wheel holder for dressing • Grinding wheel set measuring adapter • HSK calibration disc • Calibration roller • Measuring: • Heliset Plus measuring device • Software/options/packages: • Tool Studio for PC • Tool Studio Step Tools • 45-degree P-System sharpening option • P36 wood drill tooling package • Drill package • Hoger P58 package • Consumables: • 4 x 208 l dielectric fluid

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, machine/vehicle number: AFMAAAABABAA+, The Coriolis Mass Flowmeter Proline Promass 83F, manufactured by Promass in 2011, is a precision instrument designed for accurate mass flow measurements in various industrial processes. This model, designated as 83F1H-3967/0 with serial number E710E302000, has a nominal size of DN100 (4 inches) and is equipped with a hygienic process connection DN100 DIN 11851, making it suitable for applications requiring sanitary standards, such as dairy processing. Nodey Anhzjpfx Ab Uodb Constructed from high-grade stainless steels 1.4404/316L and 1.4539/904L, the device offers durability and corrosion resistance. It is rated for a nominal pressure (pnom) of 25 bar and operates in a process temperature range from -50°C to +200°C, with an ambient temperature tolerance from -20°C to +60°C. The flowmeter's housing features IP67 and NEMA/Type 4X protection ratings, ensuring resistance to dust and immersion in water. Sensor calibration includes a K factor of 1.6287 / 51 and a density accuracy of 0.0005 g/cc. The surface finish meets hygienic standards, featuring a roughness of 0.8 µm (150 grit). The unit is powered by a voltage range of 20-55 VAC or 16-62 VDC, consuming 15 VA/W at a frequency of 50-60 Hz. The housing shows some surface wear and minor dents, and the label exhibits slight wear but remains mostly legible. It is mounted on a wooden pallet and is equipped with attached braided cables with yellow markings and black cable ties. Some dust accumulation is visible on the flowmeter body, indicative of prior use. This Promass 83F flowmeter is suitable for precision mass flow measurement in the pharmaceutical, chemical, and food industries, particularly where hygienic conditions are required.

Condition: used, mileage: 2,02,000 km, power: 355 kW (482.67 HP), first registration: 03/2024, fuel type: diesel, overall weight: 20,500 kg, axle configuration: 2 axles, next inspection (TÜV): 02/2026, brakes: retarder, color: white, gearing type: automatic, emission class: euro6, Year of construction: 2023, Equipment: air conditioning, electronic stability program (ESP), navigation system, parking heater, soot filter, DAF XF480 FT Super Space Cab – One of the last new MY2017 XFs! ----Nutzfahrzeuge Göppl GmbH – Authorized DAF Dealer----USED VEHICLE – AVAILABLE IMMEDIATELY Manufactured: 12/2023 First registration: 08.03.2024 Roadworthiness certificate (HU): 02/2026 Safety inspection (SP): 08/2025 Warranty: Plus Vehicle: 3 years – 500,000 km full warranty Next service: March 2026 – 250,000 km Equipment: - Super Space Cab - Air-suspended cab - Exterior sun visor, “green light-permeable” - Fog lights with cornering/turning illumination - Skylights - Aero package - Fixed roof spoiler Nsdpfx Abexdgd Uj Ujdb - Side skirts - Side deflectors - “Super Air” driver’s seat with heating and ventilation - Passenger seat: Basic - Curtain with partition curtain - LED cabin lights - Upper bunk - Lower bunk with 65-liter drawer - XtraComfort mattress - Refrigerator - Automatic climate control - Auxiliary heater - DAF Night Lock - Manual master switch - Turn assist system - Axle load monitoring - Adaptive cruise control with FCW and AEBS - MX-13 engine, 355 kW/483 HP, EURO 6 - ECO-Performance - 12-speed TraXon gearbox - ZF-Intarder - Rear axle ratio: 2.38 - Wheelbase: 3.80 m - Tires: Pirelli - Front: 385/55R22.5 - Rear: 315/70R22.5 - Suspension: - Front: 8.0t parabolic - Rear: 13.0t air suspension - SAF S36-20 fifth wheel, 150+40mm - Alternator: 150A, batteries 2x 210Ah AGM - Battery energy monitoring - Heated fuel pre-filter - Aluminum fuel tanks: 845 + 340 liters - AdBlue tank: 90 liters - Splash guard - Preparation for gearbox PTO Optional: - OBU installation - Tachograph calibration - Gearbox PTO - Hydraulic system: tipper/walking floor/tanker ----Nutzfahrzeuge Göppl GmbH Weiden – Regensburg – Leupoldsgrün – Bamberg – Nuremberg Authorized DAF Dealer – DAF Service Partner – FIAT Professional Service Partner Subject to errors and prior sale Sale to commercial customers only.

Year of construction: 2016, operating hours: 9,580 h, condition: excellent (used), functionality: fully functional, Edge Polisher Comandulli Musa 7+4 DX Partially processed meters – 5578m Total operating hours – 9580h Working direction: from right to left - Advance/feed speed (conveyor belt) 0–3 m/min - Belt width 600 mm - Working thickness 10–80 mm Ndodpfxjzipzgj Ab Usb - Min. working width 80 mm - Max. working width (without bar) 1200 mm - Max. working width (with bar) 3000 mm - Loading plane height 750 mm Aggregates: - Calibrating spindle for vertical and horizontal positioning for a 260 mm diameter flat diamond wheel - Edge polishing spindles no. 7 with floating mechanism – oscillation - Beveling spindles no. 4, the first two beveling spindles (no. 1 upper and no. 1 lower), inclined at 45°, are equipped with the mechanical locking system TMM3. Two spindles at 45° (no. 1 upper and no. 1 lower) for polishing the previously generated bevels. Automatic valves for the water 2 roller tables, 1.5 m each Color touch screen Rated output 22 kW Dimensions (excluding rollers) 5.15 x 1.8 x 1.74 m Weight 4000 kg

Condition: like new (used), functionality: fully functional, working width: 1,300 mm, grinding width: 1,300 mm, overall weight: 2,240 kg, grinding height: 160 mm, working height: 160 mm, height adjustment type: electric, workpiece height (max.): 160 mm, table width: 1,300 mm, workpiece width (max.): 1,300 mm, VIET Challenge 211 B Wide Belt Sander – 2 Heads! LIKE NEW! Professional, Italian wide belt sander – VIET Italia Challenge 211 B calibrator. This machine is equipped with two sanding heads, enabling calibration and precise sanding in a single pass. Head configuration: - First head – calibrating roller - Second head – hard rubber roller for precise sanding - Pneumatic oscillation and belt tensioning - Air blowing and cleaning system for the belts on both heads Nedpfx Abszxz E Ns Uodb - Pressure rollers for processing shorter workpieces The machine is suitable for processing solid wood, laminated boards, MDF, plywood, veneer, and furniture components. Its heavy-duty construction ensures stability, high calibration accuracy, and excellent surface finish. Technical data: - Manufacturer: VIET Italia - Model: Challenge 211 B - Type: Wide belt sander / calibrator - Number of sanding heads: 2 - Maximum working width: 1300 mm - Material thickness range: approximately 3–160 mm - Adjustable feed speed - Control from the operator panel - Pneumatic belt tensioning - Pneumatic belt oscillation - Air blowing of sanding belts - Pressure rollers for short workpieces - Power supply: 400 V - Compressed air requirement: approximately 6 bar - Machine weight: approximately 2240 kg The machine is available immediately. It can be started and inspected before purchase. We offer assistance with loading and can arrange transport throughout Poland and abroad. JBS WOODWORKING MACHINERY Sale of used and new woodworking machines. It is possible to view the machine in operation by prior arrangement. You can test the machine on-site. Financing options are available through leasing or installment plans. WE ORGANIZE TRANSPORT WHERE CAN YOU SEE OUR MACHINES? JBS WOODWORKING MACHINERY WOLICA DRUGA 26 23-310 MODLIBORZYCE jbsmaszyny.pl

Condition: excellent (used), Year of construction: 2015, operating hours: 3,104 h, functionality: fully functional, machine/vehicle number: 11415741834, operating hours of spindle: 1,347 h, Equipment: chip conveyor, documentation/manual, DMG MORI DMU 50 – 5-Axis Machining Center – Excellent Condition – Only 1,347 Spindle Hours For sale is a meticulously maintained DMG MORI DMU 50 5-axis machining center from 2015. The machine was relocated to our facility in June 2026 and subsequently fully commissioned, geometrically measured, and technically inspected by the DMG MORI factory service. During this process, all functions were checked, the machine was realigned, the measuring probe was calibrated, and the kinematics were checked and corrected. Afterwards, a successful test run was performed without any issues. The machine is immediately ready for production. With only 1,347 spindle hours and approximately 3,104 operating hours, the machine is in exceptionally good technical condition. Technical data: • Control system: Siemens SINUMERIK 840D solutionline / CELOS • Spindle speed: 14,000 min⁻¹ • Machine weight: approx. 4,450 kg • Voltage: 400 V / 50 Hz Equipment: Nodpsziz S Dofx Ab Usdb • 5-axis machining • Siemens SINUMERIK 840D solutionline / CELOS • Internal cooling (IKZ) • High-pressure coolant system • Chip conveyor • 3D measuring probe • Tool measuring device TT160 • Electronic handwheel • USB interface activated • CELOS user interface Maintenance / Service: DMG MORI Service, July 2026 The following work was carried out by the manufacturer: • Machine realigned • Geometry fully checked • Geometry report created • Measuring probe newly calibrated • Kinematics checked and corrected • Tool measuring device TT160 refurbished • Complete function test performed • Operator training provided The machine was subsequently fully inspected and approved by DMG MORI.

Year of construction: 2015, operating hours: 100 h, condition: excellent (used), functionality: fully functional, machine/vehicle number: 4S 10kN 2268/000 1215 902, Dyna-Mess TP 10kN HF Cyclic Testing Machine / Endurance Testing System – Top Condition, including Temperature Chamber (up to 120°C) & Software Description: Manufacturer: DYNA-MESS Prüfsysteme GmbH Model: TP 10kN HF (Servopneumatic High-Frequency Cyclic Testing Machine) Maximum Testing Force: 10 kN (Static and dynamic range) Maximum Machine Stroke: 12 mm Date of Purchase: December 2015 Condition: Almost new, very little use, ready for immediate use (Plug & Play) Availability: Immediate For sale is a compact, high-precision cyclic testing machine from the premium manufacturer DYNA-MESS with a nominal load of 10 kN and a stroke of 12 mm. The system was acquired for dynamic endurance tests and service life determinations as part of a research project and has not been used since. It is in excellent, virtually new condition, both visually and technically. The complete package includes a matching temperature chamber with a controller up to 120°C. This enables standard-compliant, dynamic testing of components and materials under realistic thermal ambient conditions. System & Scope of Delivery: Load frame Dyna-Mess TP 10kN HF with high-precision force and displacement sensors. Complete PC including installed and calibrated control software DYNA-TCC under Windows 7. The system operates completely independently and is ready for immediate start-up. Nedpfx Aezunz Neb Uodb Temperature chamber with external control unit for tests up to 120°C. All associated documentation and connection cables. The machine is perfect for laboratories, universities or quality assurance departments that are looking for a reliable system for fatigue and endurance testing without incurring the budget of a new device. Inspection of the machine is possible by prior arrangement. As this is a commercial sale, it is offered ex works without any guarantee or warranty. The sale is preferably to buyers who will collect the machine themselves (dismantling and transport must be organized by the buyer). Price: €24,500 (negotiable) plus VAT.

Condition: used, Year of construction: 2000, Fine bakery line Seewer Rondo SPF 602 Nodsz A Sdhjpfx Ab Uedb Condition: used, functional Year of manufacture: 2000 Calibrating head, year of manufacture 1996 Cutting station Spraying device Filling station Guillotine Includes cutting tools

Condition: good (used), Year of construction: 2019, functionality: fully functional, Table surface: 7,500 x 2,500 mm Positioning speed: 40,000 mm/min Positioning accuracy: = 0.06 mm/min Repeatability: 0.05 mm/min Machine weight approx.: 2,300 kg MicroStep CNC cutting system of the MG series with the following features: Nsdpezwl Dmsfx Ab Uodb - Hypertherm® XPR170™ plasma power source with automatic OptiMix™ console - Plasma rotator for weld preparation - Fully automatic oxy-fuel torch - Fully automatic drilling spindle MG-40-P26 with 26.8 kW - Steel portal driven and stiffened on both sides for a clear and precise cut - AC servo motors from Panasonic for high drive power and excellent dynamics - Durable and low-maintenance planetary gearboxes - User-friendly machine control - High reliability and long service life, even in three-shift operation - MicroStep iMSNC® machine control with MMI console and 24" touchscreen - iMSNC® module | User management - iMSNC® module | Expert system - iMSNC® module | Automatic calibration of mechanical sensing - iMSNC® module | Visualization of wear parts - iMSNC® module | Assistant for loading CNC programs - iMSNC® module | Management of cutting programs (MRP) - iMSNC® module | EcoInfo - iMSNC® module | MachineInfo - iMSNC® module | Assistant for service and maintenance operations - USB 3.0 connection for storage media - Remote maintenance module MicroStep RemoteDiagnostics® - Remote maintenance access via TeamViewer - Two LCD control units on the portal - Laser pointer with automatic offset transfer - Hypertherm® XPR170™ plasma power source - Industry-leading cut quality - X-Definition - Advanced HyDefinition technology - Automatic gas console | OptiMix™ - CNC interface for the Hypertherm® XPR170™ Connection to the CNC control - Module for automatic power control of the Hypertherm® XPR170™ - Electrical and mechanical torch sensing - Remote activation of plasma power source - Double-sided cable protection (collision protection) of the portal bridge via emergency stop - Extraction table system with oscillating conveyor OXYtrac 2580 HD Main components and dimensions: 1 Table consisting of: 4 table elements WxLxH (mm) 2,600 x 2,080 x 950 Total support area: WxLxH (mm) 2,600 x 8,320 x 950 Contiguously usable working area per table: Vertical cutting: WxL (mm) 2,500 x 8,000 Bevel cutting: WxL (mm) 2,000 x 8,000 Table width (outer): W (mm) 2,830 2 Oscillating troughs L (mm) approx. 8,900 Cutting processes and associated extraction capacity: 1x Plasma max. 170 Amp., bevel cutting 1x Oxy-fuel max. 100 mm workpiece thickness regularly 200 mm workpiece thickness occasionally

Condition: used, 13 setting rings Company Märklen: 16; 40 Company Hommel: 27; 57; 56; 68; 65 Company Fer Ter: 38.997; 42.5025 Manufacturer unknown: 8.005; 19; 49; 55 Calibration rings, e.g. 16.000 mm, Ø 20 mm Calibration tools from various manufacturers for inspection – calibration ring used Nodpfx Aozumixob Uodb Price negotiable Our asking price for 24 pieces is €390 net, ex works, plus packaging costs. All technical information is subject to typographical errors and omissions. Sale exclusively to countries within the EU.

Condition: new, Year of construction: 2021, machine/vehicle number: GWH432125, Working width 1,100 mm, Sanding belt dimensions 1,120 x 2,150 mm, Max. work piece thickness 160 mm, Combination sanding unit with calibrating roller D = 150 mm, Pneumatic segmented sanding shoe with insert control, Motor 15 kW (20 hp), Sanding belt speed 18 m per second, Infinitely variable feed speed 4 - 20 m/min, Feed motor 0.55 kW (0.75 hp), Electric table positioning with motor 0.24 kW and digital LCD height display, Ndedpfx Abehgmmas Uob Mechanical "ECO GEAR SYSTEM" (oscillation of the sanding belt), Automatic belt centering, Automatic emergency table lowering, Check control panel, Automatic sanding roller shut-off on the control panel, Sanding grit adjustment with 6 positions for 2 rollers each in the infeed and outfeed, Dust extraction connection D = 160 mm, Machine complies with CE regulations Dimensions approx. L x W x H, 1,650 x 1,800 x 2,025 mm Weight approx. 1,300 kg, (Identical construction to Unitek LC 1120 1N KRT) Ex works, from warehouse Seevetal, subject to prior sale, without transport, assembly and instruction.

Condition: like new (used), machine/vehicle number: 00399, LT Industries – Quantum 1200 Plus, model 20 channel multiplexer • Real-Time Multi-Constituent Process Analyzers • Multipoint, Fiber Optic Multiplexing Capability • Shock and Vibration Free The LT Industries Quantum 1200 Process Analyzer Series is comprised of the rugged, rapid scanning Quantum 2000 and 1200 Systems which were developed for both Pilot Plant and dedicated stand-alone installations in closed-loop-control of manufacturing processes. Using rugged, proven technology, LT Industries' systems enhance quality control, increase yield and reduce waste by providing real-time analysis. The sampling process is non-destructive and non-extractive, involving none of the sample preparation required by other testing technologies. LT Industries' Quantum 1200 Process Analyzers provide continuous multiple analyses in real-time. These analyses have proven to be as accurate as traditional lab testing for liquids, powders, solids, slurries, pastes, emulsions and/or suspensions. These systems deliver the real-time data output that has made LT Industries a recognized NIR leader in process measurement for control. Artisan Scientific Corporation dba Artisan Technology Group is not affiliated with or a distributor for LT Industries. The depiction, description, or sale of products featuring names, trademarks, brands, and logos is for identification and/or reference purposes only and does not indicate any affiliation with or authorization by any rights holder. T Industries' Quantum 1200 Process Analyzers provide continuous multiple analyses in real-time. These analyses have proven to be as accurate as traditional lab testing for liquids, powders, solids, slurries, pastes, emulsions and/or suspensions. Our systems deliver the real-time data out-put that has made LT Industries a recognized NIR leader in process measurement for control. The Quantum 1200 Process Analyzer Series combines analytical power and intelligence with ease of use in an integrated systems package. A pre-dispersed, monochromatic beam of light travels through the patented harmonic drive grating mechanism, where is it separated into discrete wavelengths and sent through a fibre optic link to illuminate the sample. The light transmitted back through the fibre optic link is converted into an electrical signal, which is compared by the microprocessor to the calibrated responses in memory. The data output results of this comparison are then used for process control Important Notice: Other accessories, manuals, cables, calibration data, software, etc. are not included with this equipment Delivery condition, FCA: Oradea/Romania We can deliver/export everywhere in the World. Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare prealabila. Nsdpfxeg Tdwvs Ab Ujdb We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: used, This listing is for 1 of 4 Parker SciLog SciPres Pressure Monitor. The unit is in full working condition and is ready for immediate release The Parker SciLog SciPres Pressure Monitor is a pre-calibrated, single-use pressure sensor specifically engineered for biopharmaceutical applications. It seamlessly integrates advanced pressure sensing with disposability, offering a hassle-free setup that enhances operational efficiency in critical environments. Key Features: - Pre-calibrated Sensors: Each sensor comes pre-calibrated for immediate use, simplifying setup and reducing error risks. - Unique ID for Traceability: Each unit is pre-programmed with a unique identification number, enabling thorough traceability and data documentation through the SciLog® SciDoc software. - Integrated Calibration Data: Calibration and identity information are stored on the sensor's chip for easy access and validation. - Simultaneous Inputs: The monitor can display inputs from up to three SciPres pressure sensors at once, providing comprehensive monitoring. - Pressure Calculations: It calculates and displays both trans-membrane pressure (TMP) and differential pressure (dP) for enhanced process visibility. Ndedpfx Ajxxycysb Ueb - Stability: Gamma-stable, NaOH stable, and autoclave stable, ensuring compatibility with various sterilization processes and chemical environments. Applications: - Filtration Processes: Ideal for monitoring pressure changes in filtration systems for efficient operation. - Chromatography: Supports precise pressure control, crucial for effective separation processes. - Reverse Osmosis: Ensures accurate pressure measurements for optimally functioning systems. - Fermentation: Monitors pressure conditions critical for bioprocessing and yield optimization. Additional Specifications: - Digital Display: Easy-to-read digital interface for real-time monitoring of pressure data. - Plug-and-Play Convenience: Designed for out-of-the-box use, allowing quick integration into existing systems without extensive setup.

Condition: new, Year of construction: 2023, functionality: fully functional, machine/vehicle number: AE00003735, overall weight: 4,300 kg, input frequency: 50 Hz, input current: 126 A, input voltage: 400 V, warranty duration: 12 months, Basic information Manufacturer: SCM Group / DMC Model: DMC Eurosystem M4 1350 Year of manufacture: 2023. Condition: unused, new Operating hours: 0 h Working width: 1.350 mm Working thickness: 3-200 mm Feed speed: 2-16 m/min Power supply: 400 V, three-phase, 50 Hz Rated current: 126 A Weight: approximately 4,300 kg Serial number: AE00003735 Location: Tenja, Croatia Availability: immediately Description; For sale is an unused SCM DMC Eurosystem M4 1350 automatic wide-belt sanding and calibrating machine, manufactured in 2023. The machine has never been used in production and has 0 operating hours. It is installed at our production facility and is available for inspection by prior appointment.   Working unit configuration 1st working position - sanding roller • R 320-2620 sanding unit • Roller diameter: 320 mm • R45 rubber-coated roller, 45 Shore hardness • 15 kW motor with frequency inverter • Oscillating abrasive-belt blowing and cleaning system 2nd working position - brush unit • BF 300 brush unit • SI 300-E helicoidal brush roller • 3 kW motor with frequency inverter • Abrasive inserts, grit 180 and 240 • Automatic electronic brush position setting • Side oscillation and reversible brush-roller rotation 3rd working position - brush unit • BF 300 brush unit • SI 300-E helicoidal brush roller • 3 kW motor with frequency inverter • Abrasive inserts, grit 180 and 240 • Automatic electronic brush position setting • Side oscillation and reversible brush-roller rotation 4th working position - superfinishing sanding pad • S-2620 unit with superfinishing sanding pad • PE 32/L EPICS electronic sectional sanding pad • Segment pitch: 32 mm • 11 kW motor with frequency inverter • Electronic working-pressure control • Oscillating abrasive-belt blowing and cleaning system   Outfeed finishing unit • SB/U oscillating finishing unit • SB 200 UFC Ultra Fine brush roller • Silicon-carbide fibres • Rotating blowers for final workpiece cleaning Additional equipment • Fixed working height of 900 mm • BL 32 electronic infeed panel-reading bar • EPICS electronic sectional-pad system • Vacuum conveyor system with motor up to 7.5 kW • Perforated vacuum conveyor belt • Rubber-coated conveyor belt, 50 Shore hardness • 2.2 kW conveyor-belt drive motor • Front and rear roller support tables • Eye-M industrial PC Ndsdpfszyghlox Ab Ueb • 21.5-inch Full HD touchscreen • Maestro Pro-Sand control software • Remote service capability • Operator interface in English and Croatian • CE-compliant version Inspection and terms of sale; The machine is available immediately and can be inspected by appointment at our production facility in Antunovac, Croatia. The machine is offered ex location. Dismantling, loading, transport and installation at the buyer's site will be agreed separately. All technical information is based on the original SCM quotation and the machine identification plate. The buyer may verify the specifications and condition during inspection. Additional photographs, videos, the original technical specification and the relevant SCM documentation are available to serious prospective buyers. Price; EUR 125,000 net, plus VAT - negotiable

Condition: excellent (used), Year of construction: 1995, functionality: fully functional, machine/vehicle number: 94681, travel distance X-axis: 700 mm, travel distance Y-axis: 900 mm, travel distance Z-axis: 500 mm, overall weight: 3,000 kg, ZEISS PRISMO 5 3D coordinate measuring machine with VAST probing system For sale is a used ZEISS PRISMO 5 3D coordinate measuring machine, serial number 94681. The machine is equipped with a ZEISS-VAST probing system and a comprehensive multi-probe changer. A machine-side ZEISS control console is also included. Additionally available is a cabinet with probes, which is not included in the stated machine price and can be offered separately if desired. Details regarding the content and scope of the probe inventory can be provided upon request. Machine data Manufacturer: ZEISS Model: PRISMO 5 Serial number: 94681 Probing system: ZEISS VAST Equipment: Multi-probe changer Condition: used ZEISS service and inspection marking The machine has a marking from the technical service department of Carl Zeiss IQS Deutschland GmbH, referring to an inspection according to DIN EN ISO 10360. Documented specifications: MPE(E0): 2.70 + L/250 P: 2.00 RONt: 4.40 Type: PRISMO 5 Serial number: 94681 Calibration date: 02/2025 The values stated are reproduced according to the ZEISS marking on the machine. ZEISS CALYPSO 5.8 is visible on the existing control PC. The exact scope of the license or the transferability of an existing software license is not part of this information and can be checked separately if desired. Optionally available In addition, there is the possibility of purchasing a separate cabinet with a comprehensive inventory of ZEISS probes and accessories. This cabinet is not included in the machine price and can be offered separately if desired. Ndedpfxszwvk Ro Ab Ueb Condition and inspection The machine is in used condition. An inspection is possible after prior arrangement. The exact scope of delivery can be agreed upon or checked based on the available components if there is concrete interest. Errors, changes and prior sale are subject to change. HOLZHÄUER Hydraulik & Maschinenbau GmbH

Condition: like new (used), functionality: fully functional, Year of construction: 2018, operating hours: 60 h, Equipment: CE marking, A stunning toroidal edge polisher, practically brand new! Tilting calibrator 2 pre-cutting/chamfering stations Njdpfx Aozxi Husb Uedb 6 polishing heads