Used Heating Press Double Column Press 120 T for sale (89,698)

Condition: as good as new (ex-display), Year of construction: 2023, pressing force: 120 t, table length: 600 mm, table width: 600 mm, Here are the technical data of the offered machine: Technical data + information: HB 2021-A-188, oil hydraulic double column press 120 T bottom piston heating press. - idle speed up to 40 mm/sec - Opening speed up to 40 mm/sec - Starting press speed 5-15 mm/sec - Table size/heating plate size 600 × 600 mm - ram size/heating plate size 600 × 600 mm - 2 heating plates, electrically heated, up to 250 degrees - as OPTION - total size approx. 2000 × 1000 × 2800 mm height - Oil temperature control - Automatic lubrication - Free positioning of the ram - SICK/LEUTZE light barriers 14,1 mm on front side - Circuit oil cooling - Pressure holding valve 0 to 1800 sec. - Rear monitored door - Pressure adjustment from 30 T to 120 T - Travel limitation either by pressure or position - Programming set-up mode, single stroke (adjustable via rotary switch) - Control panel permanently installed in cabinet wall - Two-hand operation - Machine body double painted - Signal light: red: alarm, yellow baking phase, green: ready - Heating plates with electric heating rods, up to max. 250 degrees - Assembly, commissioning, instruction against separate charge Nledpfx Ahsk S Dt Tsnof Thermally neutral 80 - 120 °C Number of operating sides 1 side Forces Pressing force max. 1,600 kN Free ripping force max. 200 kN Pressure build-up time closed die steel to steel Max. 8 sec. Dimensions Max. Opening width per compartment 200 mm Stroke and min. opening per compartment 400/200 mm Table height above floor, without heating pl. 850 mm Height above floor (overall height) approx. 2.800 mm Hall height min. 3,500 mm Parallel deviation at 20 °C +/- 0.1 mm Deflection Determined at max. clamping force with 70 % occupancy ≤ 0.2 mm/m Total weight of the press without operating materials approx. 9 to Accessories: 4 HEATING PLATES 500 × 400 mm, max. heating capacity Equipped with temperature sensor 300 degrees Speeds Fast closing with 15 mm sec. Pressing speed 10 mm sec. Sound pressure level, measured at 1.5 m height at the control panel according to DIN 45635-T16-KL3 max. 8 db(A) Number of pressing cylinders 1 pc. Operating pressure max. 240 bar Pressing pressure build-up time 4 sec. Pressure accuracy during pressing stroke +/- 5 bar Main pump BOSCHREXROTH gear pump approx. 48 L/min Oil volume approx. HLP 46 MW 300 liters Ambient temperature max. 40 °C Oil temperature max. 55 °C Automatic pressure readjustment after 5 % pressure loss Pressure stabilization for up to 1800 sec. Electrical system Main supply 400 V AC Control voltage Hydraulic pumps 24 V DC 24 V DC Frequency 50 Hz Connection hydraulic main motor 15 kW Total connection approx. without heating plates 19 kW ##### If the press does not exactly meet your requirements, please click to request an individual offer exactly according to your needs: Contact us for an individual offer HIDROBRASIL manufactures presses exactly according to your requirements at surprisingly low prices! Our great strength is special machine construction and press automation. We sell customized hydraulic presses, press brakes and impact shears at surprisingly low prices. For the hydraulics of the presses we mainly use components of leading European manufacturers.

Condition: as good as new (ex-display), Year of construction: 2020, pressing force: 20 t, Double column press 20 T capacity, a) Closing speed up to 10 mm/sec b) opening speed up to 30 mm/sec c) table size between columns 1400x1100 mm d) ram size between columns 1400x1100 mm e) Manual lubrication (via grease nipple) f) UKF pump-cooling-filtration ( electrical cooling ) g) Pressure adjustment from 4 T to 20 T ( adjustable via rotary control ) h) Travel adjustable via slide control Type of construction Press design Double column press ,hydraulic Thermally neutral 80 - 120 °C Number of operating sides 1 side Forces Pressing force max. 200 kN Free ripping force max. 20 kN Pressure build-up time Closed tool Steel on steel Max. 4 sec. Dimensions Max. Opening width 500 mm Stroke 300 mm Table height above floor, approx. 900 mm Height above floor (headroom) approx. 2800 mm Hall height min. 3,500 mm Parallel deviation at 20°C #ERROR! mm Deflection Determined at max. clamping force with 2/3 occupancy < = 0.4 mm/m Weight Total weight of the press without operating materials approx. 3 to Table cut-out Size 1100x850 mm Speeds Fast closing with 9 mm sec. Pressing speed 9 mm sec. Sound pressure Sound pressure level, measured at 1.5m height at the control panel according to DIN 45635-T16-KL3 max. 78 db(A) Hydraulics Number of press/driving cylinders 2 pcs. Nlsdpfx Aohmbhqjhnof Operating pressure max. 280 bar Pressing pressure build-up time 3-5 sec. Pressure accuracy during pressing stroke +/- 5 bar Main pump BOSCHREXROTH/PARKER approx. 35 L/min Oil volume approx. HLP 46 D 150 litres Ambient temperature max. 40 °C Oil temperature max. 55 °C Flow temperature °C Circulation pump for cooling ACS approx. 6.5 L/min Electrical system Main supply 400 V AC Control voltage 24 V Frequency 50 Hz Hydraulic connection Main motor 3 kW Total connection Approx. 5 kW

Condition: new, Year of construction: 2026, pressing force: 30 t, DURENDUS 30 T Heated Press – Double Column Press – 700 × 500 mm Heated Plates, Sliding Table The machine shown here was already built and delivered to a customer. We can manufacture this machine for you again on very short notice—customized to your individual requirements if desired. This is a hydraulic heated press with electrically heated plates and a manual sliding table for pressing, laminating, and forming processes involving heat. Base price: €42,000 net Options (on request): Nlodpfx Ajy H Dtzehnof The listed options are based on completed customer projects and allow targeted customization of the machine to the specific application. The base machine provides a functional standard configuration—in practice, it is often supplemented with additional features and configured according to project requirements. ==== Technical Data + Information: ==== General Information * Design: Double column press * Pressing force: 30 t (adjustable) * Total weight: approx. 3,200 kg * Overall dimensions (W × D × H): 2,000 × 1,500 × 2,850 mm ==== Working Area * Table size: 700 × 500 mm * Heating plates: 700 × 500 × 65 mm * Installation height: max. 800 mm * Table stroke: 500 mm (manual) ==== Table & Ram * Ram stroke: 600 mm * Cylinder diameter: Ø 130 mm * Piston rod: Ø 80 mm * 8-point slide guide for parallelism ==== Speeds * Working speed: 9 mm/s * Return speed: 25 mm/s ==== Hydraulics & Drive * Working pressure: max. 240 bar * Pump output: 12 l/min * Motor power: 3 kW * Hydraulic tank: 80 l * Pressure accuracy: ±5 bar * Hydraulic system with air cooling ==== Control & Operation * SIEMENS S7-1200 control with 7" touch panel * Programmable parameters (stroke, pressure, time, cycles) * Two-hand operation * Electrical connection: 400 V / 50 Hz * Total connected load: approx. 25 kW (including heating) ==== Equipment * Electrically heated press plates up to 200 °C * Temperature monitoring with sensors * Passive pressure holding function up to 60 minutes * Hydraulic and electronic overload protection * Safety limit switches * CE certification * Dual-layer paint finish according to RAL ===== Hot pressing, laminating, plastics processing, rubber and composite material processing, forming press applications Heated press, hydraulic press, double column press, thermo press, laminating press, industrial press Are you looking for a hydraulic press tailored to your application? Contact us for a customized quotation. Our hydraulic presses are manufactured in compliance with German and European Machinery Directives (Directive 2006/42/EC), EC standards, and EU safety regulations. Furthermore, our presses exceed Canadian and European safety requirements as they fully comply with the Brazilian National Safety Directive NR 12, which is based on and extends these standards. Our key strength lies in special purpose machine construction and press automation. We offer custom-built hydraulic presses at surprisingly affordable prices. For the hydraulics, we primarily use components from leading European manufacturers.

Condition: used, Year of construction: 1988, pressure 400 t distance between columns 1100 mm stroke 250 mm no. of strokes 25 - 75 /min distance table/ram, max. stroke up, adjustment up 900 mm table surface area 1100 x 965 mm capacity of ejector in table 30 t ejector stroke of ejector in table 80 mm Nlsdpfx Ahszrpt Uonjf capacity of ejector in ram 3 t stroke of ejector in ram 60 / 70 mm ram surface 980 x 800 mm column travel -side 800 mm ram adjustment 20 mm power capacity 80,0 + 5,5 kW weight 47,0 t Dimensions (WxDxH) 3,5 x 3,3 x 6,0 m weight of switch cabinet 1,4 t dimensions of electrical cabinet (WxDxH) 4,9 x 0,5 x 2,6 m Multi-station cold extrusion press with link drive with infinitely variable drive, hydraulic clutch-brake combination (Ortlinghaus), hydraulic overload protection in the slide, motorised slide adjustment, pneumatic counterbalance cylinder in press frame, cam-controlled ejector in table (30 t / 80 mm), pneumatic ejector in slide (3 t, 60 mm), motorised central lubrication

Condition: good (used), Cauhe S-IV A 120×160 Hot Stamping Press The machine is fully operational, like new. Made in Spain. Format: 1200x1600mm Weight: 10,000kg Power supply: 380V Nsdpezlaitofx Ahnslf Motor: 11 kW Impact force: 2 Tm/dm² Equipment: – Pneumatic clutch and brake – Control panel – Full-format heating plate with 3 heating sections – 3 operating modes: continuous, time-delayed, manual – 3 independent foil feeds – Central automatic lubrication – Additional safety guards – Operating tools – Press plate

Condition: good (used), Year of construction: 1982, Press force: max. 200 kN Safety distance: 100mm Post-travel: max. 10 mm Motor power: 3 kW Nedezvfp Hopfx Ahnjlf

Condition: used, Year of construction: 1998, machine/vehicle number: SN: 5-2067, functionality: unexamined, power: 45 kW (61.18 HP), pressing force: 255 t, overall weight: 24,800 kg, PME Erfurt, Type: ZH 2500 / 1600, Serial No.: 5-2067, Year: 1998, 2500 kN, in operation until December 2025 Nlodpozvcxljfx Ahnof Technical data of the press according to the nameplate: Press force: 2,500 kN Stroke rate: 25-75 strokes/min Rated stroke rate: 40 strokes/min Stroke: 20-200 mm Ram adjustment: 140 mm Total power: 45 kW Operating voltage: 400 V Frequency: 50 Hz Machine weight: 24,800 kg Strip feeding system consisting of: PBK, Type: Roller feeder WV-120/DSM 500P, Serial No.: BA00482, Year: 1998, PBK, Type: Straightening machine, Year: unknown, PBK, Type: Unwinding reel SCi 530 M, Serial No.: BA00482, Year: 1998 including enclosure and roller conveyor with peripherals: - Conveyor system Functionality and technical data have not been verified. without additional items/without further accessories, unless explicitly stated as part of the item. If interested, please contact us by email.

Condition: as good as new (ex-display), Year of construction: 2022, pressing force: 400 t, Press design double column press Thermally neutral 80 - 120 °C Number of operating sides 1 side Forces Pressing force max. 4000 kN Free ripping force max. 400 kN Pressure build-up time Closed die steel to steel Max. 4 sec. Dimensions 3,800 mm long and 4,475 mm wide Max. Opening width 800 mm Stroke 800 mm Table height above floor 1100 mm Height above floor (headroom) approx. 4300 mm Hall height min. 5500 mm parallel deviation at 20°C +/- 0,1 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.2 mm/m Weight Total weight of press without operating materials and table plate approx. 28 t Press table Table size 1500x1500 mm Speeds Fast closing with 100 mm sec. Pressing speed 8 - 3 mm sec. Sound pressure Sound pressure level, measured at 1.5m height at the control panel according to DIN 45635-T16-KL3 max. 78 db(A) Hydraulics Number of pressing cylinders/driving cylinders 1 pc. Operating pressure max. 300 bar Pressing pressure build-up time 4 sec. Pressure accuracy during pressing stroke +/- 3 bar Main pump BOSCHREXROTH axial piston pump approx. 145 L/min Oil volume approx. HLP 46 MW 1000 liters Ambient temperature max. 40 °C Oil temperature max. 55 °C Flow temperature °C Auxiliary pump BOSCHREXROTH, gear pump 10 L/min Pressure stabilization for up to 300 sec. Electrical system Main supply 400 V AC Control voltage 24 V DC Frequency 50 Hz Connection hydraulics main motor 40 kW Sliding table press with 400 T capacity, Closing speed up to 100 mm/ ( adjustable via touch screen ) Opening speed up to 100 mm/sec ( adjustable via touch screen ) Starting press speed 10 mm/sec ( adjustable via touch screen ) table top size 1500x1500mm ram size approx. 1600x1500mm Oil temperature monitoring 55 degree warning, 60 degree shutdown Automatic lubrication ( adjustable via touch screen ) Free positioning of the ram ( adjustable via touch screen ) SICK/PILZ light barriers 14 mm, front, up to 1800 mm height Hydraulic and mechanical ram protection Circuit oil cooling ( adjustable via touch screen ) Ejector in table, 20 T press force, 350mm travel Ejector moves outwards with the table Table plate milled flat, with DIN 22 T grooves Pressure adjustment from 60 T to 400 T ( adjustable via touch screen ) Nlodpfx Ajph Uk Nohnsf Travel limitation either by pressure or position Set-up mode, single stroke and cycle sequence ( adjustable via touch screen ) Swiveling control panel on the cabinet Two-hand operation, with opening button, manual/single stroke/cycle switchover button Installation, commissioning, instruction against separate charge The control is supplied by SIEMENS. ( S 7 1200 ) Also the touch screen monitor with 9 inch. The remote maintenance unit SECOMEA -Ethernet is included in the delivery. The side of the press has two 1000 mm high and 800 mm wide windows with double doors. (sliding table press, hydraulic press, hydraulic press, double column press)

Condition: used, Double-column Hydraulic Press SCHÖN Type SH 25 Machine No. 2440 Year of manufacture: 1979 Press force: 25 tons Column spacing: 630 mm Lateral passage between columns: 120 mm Table area: 580 x 320 mm Ram area: 360 x 220 mm Clamping pin hole: Ø 40 mm Maximum ram stroke: 100 mm Maximum installation height: 270 mm Table height above floor: 900 mm Motor power: 7.5 kW Power supply: 380 Volt, 50 Hz - Main cylinder overhauled in 2025 - SICK LUV 206 safety light curtain - Two-hand control - Stroke counter - Rapid stroke and working stroke - Stroke limitation dependent on pressure or position - Mechanically adjustable fixed stop - Press force regulation - Press time extension 1–10 s (pressure holding time) - No operating manual and no wiring diagrams Required space (L x W x H): 1450 x 1100 x 2200 mm Weight: 1200 kg Nledpfxoyz Dr Ts Ahnjf In good condition

Condition: ready for operation (used), Two mechanical large-format double-column eccentric punching presses Rhodes (UK) are available. Press force: 350t, table dimensions X/Y: 1750mm/920mm, ram dimensions X/Y: 1550mm/615mm, ram stroke: 101mm, ram adjustment: 100mm, stroke rate: 50 strokes/min, max. installation height: 483mm, side opening X/Y: 630mm/380mm, table height: 933mm, weight: approx. 43000kg. Documentation available. On-site inspection is possible. Nledjyfv I Topfx Ahnef

Condition: new, Year of construction: 2019, pressing force: 275 t, pressure:275 t distance between columns:3000 mm total power requirement:30 kW weight of the machine ca.:40 t draw back pressure:27 t pump capacity:Axialpumpe mit Proportionalventil :6000 mm :max. 3000 mm Table dimensions:6000 x 3000 mm table height over floor:700 mm distance between table / ram:1100 mm :450 l traversing speed:auf X und Y, 30-33 mm/sec. down speed:2-10 mm/sec :2-50 mm/sec. Cylinder hub:900 mm Cylinder diameter:440 mm Stestle extension:200 / 200 mm / Ø :40 mm Siemens Control System:S7 1200 Monitor Siemens 9":Touch Panel Tax desk:tragbar Nlsdjfxyigopfx Ahnof

Condition: used, Year of construction: 1988, functionality: fully functional, Press capacity 5,000 kN Table area 2,400 mm x 1,700 mm Ram area 2,400 mm x 1,400 mm Adjustable stroke 25 mm - 200 mm Ram adjustment max. 200 mm Stroke rate 20 - 100 spm Drive power 84 kW Machine weight approx. 62,500 kg Nedpfjyg Emzox Ahnjlf with roller feeder/straightener combination + decoiler Further data and photos available on request

Condition: excellent (used), Year of construction: 2016, Specifications Manufacturer: IMV Model: DM125 Year: 2016 Condition: Used Stock number: 0396 Ram force: 1,250 t Number of press points: 2 Drive: Eccentric with stroke adjustment Ram stroke: 250–400 mm Strokes/min: 5–35 Vertical daylight below bolster, CBRA: 1,150 mm Table dimensions: 4,500 x 2,000 mm Ram dimensions: 4,500 x 2,000 mm Nlodpfsyw Uf Aox Ahnof Side column window: 2,600 mm Max. front column window: 4,900 mm Transfer cart: 2 units present Main motor power: 290 kW Press weight: 310,000 kg

Condition: used, Technical details: pressure: 80 t distance between columns: 880 mm dayligth: 200 mm Table dimensions: 880x300 mm height over floor: 1000 mm distance between columns: 800 mm total power requirement: ca. 12 kW machine weight ab.: 2855 kg space requirements of the machine approx.: T:1,4xB:1,65xH:1,9 m Embossing - Hot Embossing application area: - for example: for foils, plastics, paper, hardboard materials etc. - stamp plate size: 600x310mm equipment: - counter - hydr. tank Accessories: - Mounting plate (600x300x90mm) not heatable. Nledpfx Ahju Icwtonsf Sale as is. *

Condition: used, Year of construction: 1990, Technical details: Pressure: 63 t distance between columns: 200 mm stroke: 150 mm dayligth: 430 mm no. of strokes: 400 Hub/min T-slots H 12 650: 18 mm hole in table: 420x160 b x l mm ram surface area: 650 x 450 mm control: Wanske Tronicpress CNC passage of columns: 550x540 mm tank: 200 l stroke of ram - fixed: 100 mm ram diameter: 40 mm table height over floor: 1000 mm table: 600x450 mm table height over floor with metal base stand: 880 mm total power requirement: 30 kW weight of the machine ca.: 3,9 t Hydraulic automatic punching press for precision work (high-speed press) - for punching, drawing, pressing, minting, bending, riveting, straightening, assembling - with hydraulic gripper feed type HS 150 and 7-roller straightener (moving) - Normal strips of approx. 0.4mm - 2.5mm thickness x approx. 160mm width, as well as narrow strips up to approx. 4mm can be processed. Feed length can be adjusted as required via the control unit. - with ram round column guide - with automatic central lubrication - High-speed: up to 400 strokes min-1 Nlodpfxju Icxqo Ahnjf - motorized adjustable fixed stop (bottom can be adjusted by hand/motorized) - Operating modes such as continuous stroke and/or single stroke Equipment: - 1x hydraulic unit - 2x control cabinets *

Condition: used, Year of construction: 1987, pressure 800 t stroke 100 mm no. of strokes 45 /min distance between columns 600 mm table surface area 560 x 650 mm capacity of ejector 5 t ejector stroke 15 mm ram surface 590 x 450 mm power requirement 22,0 kW Weight 17,0 t dimensions (WxDxH) 1,7 x 2,55 x 3,1 m Nedpfozl E Saox Ahnjlf Nominal force travel 1,46 mm With knuckle-joint drive, flywheel brake, hydraulic clutch with 2nd brake, press frame balancing, single ejector in table, self-monitoring control

Condition: used, Year of construction: 1994, KAISER Press Nljdpfx Aozp Ed Rshnjf Pressing force 4,000 kN Stroke adjustment 40-200 mm Ram adjustment 150 mm Stroke rate 20-80 1/min Table area 2,340 x 1,600 mm Ram area 2,000 x 1,500 mm Installation height 550 mm

Condition: used, Double-column hydraulic press SCHÖN Type SH 25 Machine no.: 4453 Year of manufacture: 1999 Pressing force: 25 tons Column width: 500 mm Lateral column clearance: 120 mm Table surface: 440 x 320 mm Table opening: Ø 175 mm Ram surface: 360 x 220 mm Clamping pin bore: Ø 40 mm Max. ram stroke: 100 mm Max. installation height: 270 mm Nedpfxjw A Amrj Ahnjlf Table height above floor: 900 mm Motor power: 7.5 kW Connection voltage: 380 V, 50 Hz Equipment: - Safety light curtain SICK, type FGS 300-11 - Two-hand operation - Stroke counter - Rapid and working stroke - Stroke limitation dependent on pressure or position - Mechanically adjustable fixed stop - Pressing force regulation - Adjustable pressing time 1–10 s (pressure holding time) - Adjustable return stroke speed - Blow-off device electrically pre-wired, without air valve - Manual hydraulic tool safety, adjustable via handwheel Dimensions (L x W x H): 1300 x 1200 x 2200 mm Weight: approx. 1200 kg Good condition

Condition: used, Year of construction: 1990, pressure 3 t throat 0 mm stroke 200 mm total power requirement 15 kW weight of the machine ca. 4 t dimensions of the machine ca. m Nlsdpot Hw Amjfx Ahnjf Fully Automatically Straightening Press, 3 Stations,parts turning, (bolts)

Condition: new, Year of construction: 2021, pressing force: 17 t, Here are the technical data of the offered machine: If the press does not exactly match your requirement profile, please click to request an individual offer exactly according to your needs: Contact us for an individual offer HIDROBRASIL manufactures presses exactly according to your requirements at surprisingly low prices! Technical data + information: Hydraulic 17 T single column press Single column press with 17 T capacity, suitable for continuous shift operation, with these basic data: a) Traversing speed 10 mm/sec. downwards, b) opening speed up to 25 mm/sec c) starting pressing speed 10 mm/sec. d) table size 400x400 mm e) ram size 200x200 mm, with T grooves and central cylinder clamping f) Overall size approx. 1150x800x1750 mm g) oil temperature display on oil tank h) pressure adjustment from 5 T to 17 T ( adjustable by knob ) i) Hand lever operation with two speeds j) Machine body powder-coated, or double-painted k) Control cabinet supply line from above with 3000 mm cable and 16 Ampere plug l) assembly, commissioning, instruction against separate calculation Press design Single column press Thermally neutral 80 - 120 °C Number of operating sides 1 side Forces Press force max. ( at 250 bar ) 170 kN Free ripping force max. 10 kN Pressure build-up time Closed die Steel to steel Max. 2 sec. Dimensions Max. Opening width 250 mm Stroke and min. opening 100 mm Table height above floor 850 mm Height above floor (headroom) approx. 2200 mm Hall height min. 2.500 mm parallel deviation at 20°C +/- 0,1 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.3 mm/m Weight Total weight of press without operating materials approx. 1 to Speeds Fast closing with 10 mmSec. Press speed 10 - 0 mmSec Sound pressure Sound pressure level, measured at 1.5m height at the control panel according to DIN 45635-T16-KL3 max. 78 db(A) Hydraulics Number of pressing cylinders 1 pcs. Operating pressure max. 250 bar Nlodpfx Ajgrki Sshnjf Pressing pressure build-up time . 2 sec. Pressure accuracy during pressing stroke +/- 5 bar Main pump Gear pump approx. 6 L/min Oil volume approx. HLP 46 MW 100 liters Ambient temperature max. 40 °C Oil temperature max. 55 °C Flow temperature °C Electrical system Main supply 400 V AC Control voltage hydraulic pumps 24 24 V DC V DC Frequency 50 Hz Hydraulic connection Main motor 2.2 kW Total connection Approx. 3 kW Design The press is designed as an oil-hydraulic single-column press. The hydraulic system and the tank are located on the top and inside of the press, respectively. Hydraulic unit The hydraulic system is mounted on the top of the press. Safety devices For the scope of delivery described, the press complies with the valid safety regulations according to UVV, as well as with the standards and directives valid for the EU, in each case in the latest version. Electrical system / control system The control cabinet with control, power and safety components is located on the right side of the press. The press is operated by a hand lever control.

Condition: used, Year of construction: 1985, Pressure total: 250 ton Ram stroke: 70 / 250 mm Slide adjustment: 160 mm Ejector in ram: 20 ton Ejector stroke in ram: 10 mm Shut height (stroke down, adjustment up): 520 mm Free lateral opening F-B: 1.300 mm Table surface area : 1.600 x 1.600 mm Slide area: 1.600 x 1.600 mm Number of strokes: 0 - 50 s.p.m. Required power: 33 kW Height over floor approx.: 5.500 mm Nlsdeyvkukspfx Ahnjf Weight of machine approx.: 58 ton Roll feeder Material width: 1250 mm Material thickness: 0,3 - 1,6 mm Control: Siemens S7

Condition: used, Year of construction: 1989, Pressure total: 1400 ton Stroke: 950 mm Daylight: 2000 mm Nledeuqdi Uopfx Ahnef Table surface area : 3600 x 2500 mm Slide area: 3600 x 2500 mm Die cushion capacity in table: 400 ton Die cushion stroke: 500 mm Die cushion pad area: 3060 x 1860 mm Approach speed: 400 mm / sec Working speed: 40 / 80 mm / sec Return speed: 400 mm / sec Oil volume: 5000 l Required power: 450 kW Weight of machine approx.: 240 ton Standard configuration with hydraulic tool clamps on the ram

Condition: new, Year of construction: 2019, machine/vehicle number: DF0303, pressing force: 160 t, table length: 550 mm, table width: 500 mm, working height: 700 mm, pressure:160 t distance between columns:700 mm stroke:400 mm Return Capacity:16 t Engine Output:15 kW Travel:400 mm :600 mm Ram plate:700 x 600 mm table height over floor:850 mm Table size:700 x 600 mm speed of forward flow:10 mm/sec Pressing speed:10 mm/sec :10 mm/sec Oil cooling (electric):1,5 kW (max) Oil Tank Capacity:300 l weight of the machine ca.:4,2 t dimensions:950 x 2440 x 2400 m ejector:30 x 30 mm ejector stroke:150 mm pressure of ejector:15 t ejector speed:25 mm/sec Nledpfxefxyh Rj Ahnsf no. of ejector pins:1 Stück heating plates :550 x 500 mm :6800 ? :2400 ? :1200 ? :1200 ?

Condition: new, Year of construction: 2019, machine/vehicle number: DF0303, pressing force: 160 t, table length: 550 mm, table width: 500 mm, working height: 550 mm, pressure:160 t distance between columns:700 mm stroke:400 mm Return Capacity:16 t Engine Output:15 kW Travel:400 mm :550 mm Ram plate:700 x 600 mm table height over floor:900 mm Table size:700 x 600 mm speed of forward flow:50 mm/sec Pressing speed:10 mm/sec :50 mm/sec Oil cooling (electric):1,5 kW (max) Oil Tank Capacity:300 l weight of the machine ca.:4,3 t dimensions:1150 x 2600 x 2400 m ejector:30 x 30 mm ejector stroke:150 mm pressure of ejector:15 t ejector speed:25 mm/sec no. of ejector pins:1 Stück Heating panels (L x B) with 2 measuring sensors diagonally:550 x 500 mm Siemens Control System:S7 1200 Monitor:12 Zoll :2400 ? :1200 ? :1200 ? Njdpfx Asfxygpjhnelf

Condition: used, Year of construction: 2017, Schuler BEUTLER Press Nljdezui Haepfx Ahnsf Type: MC 4000 Year of manufacture: 2017 Press force: 4,000 kN Stroke rate: 20-80 strokes/min Stroke adjustment: 40-315 mm Ram adjustment: 200 mm Die height: 750 mm Table area: 3,000 x 1,400 mm Press weight: 72,000 kg Strip feeding system consisting of: GSW Schwabe, Type: MHR 5/2000, Year of manufacture: 2017 GSW Schwabe, Type: RMA 50/78, Year of manufacture: 2017