Used Jeumont Industrie Generator for sale (34,100)

Year of construction: 1999, operating hours: 76,000 h, condition: used, functionality: fully functional, machine/vehicle number: 510444, Technical parameters: • Manufacturer: Jeumont Industrie • Type: JISALT 420 • Serial number: 510444 • Apparent power: 14 MVA • Voltage: 15 kV • Stator current: 539 A • Frequency: 50 Hz Dsdpfx Aaoy D Hrzs Nokl • Rated speed: 1500 rpm • Power factor: 0.8 • Excitation voltage: 98 V • Excitation current: 454 A • Excitation with rotating diodes (brushless) • Water cooled • Insulated bearing shells on both (TE, EE) sides • Operating hours: 76,000 hours Last diagnostic inspections of the stator and rotor performed in 2023. Values and conditions were good, but factory inspection recommended. Without control and protection system!

Year of construction: 1999, operating hours: 76,000 h, condition: used, functionality: fully functional, machine/vehicle number: 510445, Gas turbine (GT) generator Technical parameters: • Manufacturer: Jeumont Industrie • Type: JISALT 460 (1999) • Serial number: 510445 • Apparent power: 60 MVA • Voltage: 11.5 kV • Stator current: 3012 A • Frequency: 50 Hz • Rated speed: 1500 rpm Dodpjy D Hp Tefx Aa Nokl • Power factor: 0.8 • Excitation voltage: 259 V • Excitation current: 617 A • Excitation with rotating diodes (brushless) • Air cooled • Insulated bearing shells on both (TE, EE) sides • Operating hours: 76,000 hours Last diagnostic inspections of stator and rotor performed in 2023. Values and condition were good, but factory inspection recommended. Without control and protection system!

Condition: used, Used Oxymat O500 PSA industrial oxygen generator made in 2012 and with capacity 40.6 m3/hour. Containerised system that includes the following equipment: - Almig 45 belt air compressor, cyclone separators, air receiver, Donaldson DCO 360 AB dryer, Donaldson ultrafilter, Oxymat 2-column O500 system, oxygen receiver, Oxymat control panel, Rix compressor, low oxygen gas detection system. - Not suitable for medical oxygen. Dkedpfx Aaeyt Rc Ie Njl

Year of construction: 1993, operating hours: 100 h, condition: used, functionality: fully functional, machine/vehicle number: 442714, Three-phase industrial generator sets with self-regulating alternator compliant with CEI 2-3 / IEC standards. Rated power 1100 kVA (880 kW) at 1500 rpm – 50 Hz operation. Units are installed on a steel base with containment system, independent control panel, and exhaust lines. Main specifications: Alternator Tessari EC 43 LA/4 Power: 1100 kVA Active power: 880 kW Rated current: up to 5000 A (depending on voltage configuration) Voltage: 127/220/254/440 V Cosφ: 0.8 Insulation class: H Year: 1993 The generator sets can be used for: Prime power generation Backup power supply Djdjytc Dwepfx Aa Njkl Power supply for large industrial facilities

Condition: excellent (used), Year of construction: 2022, operating hours: 95 h, functionality: fully functional, For sale: Complete industrial microwave generator system from MUEGGE GmbH (Germany), 30 kW at 915 MHz, in excellent condition with very low operating hours. This package includes the full WR975 high-power waveguide assembly, making it ideal for industrial heating, drying, food processing, chemical applications, and R&D environments. Technical Specifications Microwave Power Supply: • Output power: 30 kW • Frequency: 915 MHz • Input: 3 × 400 VAC, 50 Hz • Control interface: CAN • Colour: RAL7035 • Included: 10 m CAN cable Magnetron Head: • Power rating: 30 kW / 915 MHz • Waveguide interface: WR975 Dkjdpfox Ex Drsx Aa Nol Included Waveguide Components: • 100 kW circulator, WR975 • WR975 waterload • Detector diode (for forward/reflected power monitoring) • 20 dB attenuator, Type R 412 720 Documentation: • Complete English instruction manual and technical documentation provided on USB stick. Condition: • Excellent – barely used • Fully functional and tested • Located in France • Ready for immediate dispatch Applications: • Industrial microwave heating • Drying and dehydration processes • Pasteurisation and food treatment • Chemical and materials processing • Research and development Original New Price: • €109,000 (manufacturer reference) Asking Price: • Negotiable, subject to shipping and inspection

Condition: ready for operation (used), Year of construction: 2004, operating hours: 61,082 h, functionality: fully functional, travel distance X-axis: 2,800 mm, travel distance Y-axis: 2,200 mm, travel distance Z-axis: 800 mm, controller model: HEIDENHAIN TNC 426, Equipment: chip conveyor, Important information: Auction extended by 14 days. Controller has been subsequently identified as HEIDENHAIN iTNC 530. Previous specification: TNC 426. A new spindle was installed in January 2025! The machine has been regularly maintained! TECHNICAL DETAILS Travel X-axis: 2,800 mm Travel Y-axis: 2,200 mm Travel Z-axis: 800 mm Feeds Rapid traverse: 35,000 mm/min Spindle speed S1 (continuous operation) vertical: 10,000 rpm Spindle speed S1 (continuous operation) universal swivel head 2-axis: 18,000 rpm MACHINE DETAILS CNC control: HEIDENHAIN iTNC 530 Electrical data Supply voltage: 400 V (–15%, +10%) Frequency: 50 Hz Current consumption: 101.1 A Installed total power: 59.8 kW Dkjdjy Dgyfjpfx Aa Nsl Operating hours Power-on hours: 98,755 h Program run time: 61,082 h EQUIPMENT High-rigidity gantry design Precision linear guides and ball screws Generous workspace with 2.8 m X-axis travel High feed rates for efficient machining Ideal for tool, die, and machine building Documentation and acceptance certificate according to ISO standards Tool changer Cooling system Chip conveyor Swiveling milling head with 4th/5th axis

Condition: used, Year of construction: 2003, x-travel 2.500 mm y-travel 800 mm z-travel 1.250 mm Control Heidenhain iTNC 426 spindle tunring speed 4.000 U/min tool taper ISO 50 table surface area 2.200 x 750 mm max. table load 4.000 kg In our assessment, the machine is in good used condition and can be inspected under power by appointment. Djdsy I Dg Repfx Aa Njkl Technical Features & Accessories: - Automatic universal milling head, 0 and 180 degrees Accessories, tools, and clamping devices shown are only included if specifically stated in the additional information. Technical data and specifications are subject to change without notice. Prior sale is reserved.

Condition: like new (used), Year of construction: 2018, operating hours: 5,498 h, functionality: fully functional, travel distance X-axis: 2,500 mm, travel distance Y-axis: 1,300 mm, travel distance Z-axis: 3,500 mm, feed rate X-axis: 40 m/min, feed rate Y-axis: 40 m/min, feed rate Z-axis: 40 m/min, table length: 2,500 mm, table width: 3,500 mm, spindle speed (max.): 12,000 rpm, table height: 300 mm, table load: 1,30,000 kg, workpiece weight (max.): 1,30,000 kg, spindle nose: HSK A100, MOVING GANTRY MILLING MACHINE FPT MOD. DINOX 350 IAT 5 axes Numerical control: Heidenhain TNC 640 X axis: 2,500 mm Z axis (Vertical): 1,300 mm Y axis: 3,500 mm Rapid traverse: 40,000 mm/min Universal head with continuous positioning HSK A100 electrospindle interface Maximum speed: 12,000 rpm A axis: + / - 185° C axis: + / - 270° Table: 3,500 x 2,500 mm, height 300 mm Load capacity: 15t/m^2 Tool changer: 64 positions Total power: 85.13 kW Weight: 51,370 kg Complete with: - Laser probe and software for tool integrity check and tool length and radius measurement - Workpiece probing and alignment sensor - External/internal tool coolant with 1,500 l tank, p=40 bar - Workpiece washing gun with tool coolant, dedicated pump - Internal tool cooling with compressed air, High Speed - Chip conveyor USED MACHINE Dsdpfxjwzv Tcs Aa Nskl YEAR 2018

Condition: good (used), Year of construction: 1998, functionality: fully functional, Equipment: documentation/manual, Hansa Food-Mix 2000 – Industrial Cream Aerator / Continuous Mixer (similar to Mondomix®) For sale is a powerful Hansa industrial mixer Food-Mix 2000, specifically designed for the continuous processing and aeration of cream and similar products under hygienic conditions. The machine impresses with its robust stainless steel construction, precise process control, and high production capacity – ideal for use in the dairy and food industries. - Manufacturer: Hansa Industrie-Mixer GmbH & Co. KG (Germany) - Model: Food-Mix 2000 (re-infection free) - Year: 1998 - Design: Stainless steel frame and housing Dodey I A Eropfx Aa Nskl - Mobile: Machine mounted on castors - Infinitely variable mixing head drive - Speed range: 80 – 450 rpm - Motor power: 9.2 kW - Foam density: 400 – 900 g/l (cream) - Specific feed density: 1,000 – 1,200 g/l (cream) - Throughput: approx. 300 – 1,500 kg/h (cream) - Dynamic stainless steel mixing head - Mixing head volume: approx. 9 litres - Separate cooling for rotor/stator possible - Can be sterilized with steam

Year of construction: 2021, condition: as good as new (ex-display), functionality: fully functional, Single-head cutting machine OMC GIOBI 600 with measuring roller conveyor FOM INDUSTRIE ASSOMAK VS 6m and inlet conveyor PORTER 4,2m Year 2021 Condition: ex-demo, like new - Saw blade D 600 mm - Hdro-pneumatic feed - Inclination is pneumatic on both sides, with fixed graduations of 22.5° - 45° - 90°. For intermediate gradations, with manual mechanical stop - 2 vertical and 2 horisontal clamps - Spray mist blade lubrication system - Integral pneumatic protection - ASSOMAK VS 6m: measuring roller conveyor with digital display and manual length stop positioning - Minimum cut 0 mm - Maximum cut 6000 mm - Measurement reading by encoder - Positioning precision ± 0,5 mm - Loading capacity per linear meter: 10 Kg - Width of bar resting surface: 200 mm - PORTER 4,2m: inlet roller conveyor Djdpfx Asy Erwfja Nskl - Loading capacity per linear meter: 10 Kg - Width of bar resting surface: 200 mm

Year of construction: 2005, condition: used, CNC Machining Center 4 Axes – FOM (Aluminium/Steel Profiles) Configuration: 4-axis CNC Working length (X): 7,030 mm Condition: Working, maintained - Main Features CNC machining center designed for drilling and milling operations on aluminium and steel profiles, ideal for window and industrial profile production. 4-axis spindle (0° / 90° / 180°) for multi-side machining Electrospindle 4 kW – up to 12,000 rpm Tool holder: ISO 30 DIN 69871 6-position automatic tool magazine 6 pneumatic clamps (manual positioning) THK linear guides for high precision - Control & Software Software: FomCam + Prof2 (Windows XP) Easy programming with automatic CNC generation Movable control console (PC + display + keyboard) Barcode reader connection Remote control capability 📏 Technical Data X-axis: 7,030 mm Y-axis: 1,100 mm Z-axis: 425 mm Machine dimensions: 8,307 x 1,875 x 2,460 mm Dsdpfxeywhf Nj Aa Nekl Weight: 3,200 kg - Equipment Forced air spindle cooling Inverter-controlled spindle Automatic lubrication Protected tool magazine with rotary system - Machine ready to work, ideal for aluminium profile machining and window production.

Condition: used, Used DC motor Anchor 460V // Current 325A Dkedpfx Ajwbhg Uja Njl field 340V // current 4,7 A Speed 1880rpm Power 138kW

Condition: used, functionality: fully functional, Year of construction: 2026, load capacity: 300 kg, construction height: 1,950 mm, Technical condition: very good Dsdpfx Aaeymt Hce Nekl

Condition: used, Year of construction: 2017, operating hours: 1 h, Mast type: None Dkedpeymt E Sjfx Aa Nol

Year of construction: 2025, condition: new, New single head saw with up-feed blade Ø 300mm and manual positioning of vertical axis FOM INDUSTRIE PANDA 300 ECHO Dkodpfxjf Nwxws Aa Nel - Tungsten carbide saw blade Ø 300mm - Hydro-pneumatic feed of saw blade - Spray mist blade lubrication system - Cutting area guard kit - Two vertical vices - Two horizontal vices - Set up for the extraction of chips and fumes

Year of construction: 2025, condition: new, XZ100228 Single head sawing machine Ø 400 mm for aluminium and PVC with manual blade down-feed and pneumatic vices FOM INDUSTIRE SIKA PLUS M Machine in stock Configuration: - Aluminium and PVC cutting machine with CE certification Djdjpl Tgmepfx Aa Nokl - Tungsten carbide saw blade Ø 400 mm - Manual blade lowering (with lever) with pneumatic servo control to reduce operator stress - Side support plates on both sides - Blade motor power 2.2 kW - 2850 rpm - Self-braking motor with blade stop in less than 10 sec - Cutting angle from 45°Lh to 45°Rh on vertical axis and 45°Rh to 90° on horizontal axis - Intermediate angles with mechanical stop - Cylinder blocking involuntary head lowering - Double working pressure servo-controlled in low pressure - 1 pneumatic vertical vice - 2 pneumatic horizontal vices - 1 safety servo-valve for each pneumatic horizontal vice - Conical anti-crushing buffers - Worktable and turntable structure in stabilized cast iron - Motor transmission by belt - Saw blade holding spindle Ø 32 mm - Spray mist blade lubrication system - Integral blade guard in rest position - Set up for the extraction of chips and fumes

Year of construction: 2024, condition: new, 5 axis double head sawing machine FOM INDUSTRIE KEOPE E5 6.6 m Machine in stock and ready for shipping Equipment: Dkjdpfsd Izq Hsx Aa Njl - No.2 carbide tungsten saw blades Ø 600 mm - Minimum cutting capacity between two heads: 470 mm (with heads at 90°) - Maximum cutting capacity between two heads: 6.6 m - No.4 vertical vices and No.2 horizontal (for step-by-step operation) - Micro-drop pure oil blade lubrication system - Set up for the extraction of chips and fumes - Blade motors, three phase 5 HP (3.7 kW) - 230/400 V- 50Hz. Blade rotation speed 2400 RPM - Head rotation between 22.5° and 140° (Y and Z axes) with electronic control (vertical axis) - Internal blade inclination between 90° and 45° (W and U axes) with electronic control (horizontal axis) - Handling of mobile head (X axis) with electronic control - Mobile head max. speed 25 m/min. - Hydraulic saw blade feed (adjustable blade exit speed - quick return) - Profile lifting kit - Loading roller conveyor length 2.2 m, width 400 mm (on mobile head) - No.3 intermediate pneumatic retractable support - Chip conveyor belt - Label printer - FSTCut software - Software for special cut-off (beyond measure and super minimum) and profile bevel cut for 45° cuttings - Step-by-step cutting software, complete with 1 extra surface on fixed head, 90° cuts, two-hand control - Vacuum cleaner

Year of construction: 2024, condition: new, XX100329 CNC Machining Centre with 3 axes and worktable with pneumatic positioning at 0°/90°/180° FOM INDUSTRIE FMC 120 Machine in stock and ready for shipping Standard configuration: - Servo-ventilated three-phase spindle motor 3 kW, regulation of spindle rpm by numerical control - inverter (1000/17000 rpm) - 6 position tool-holder for manual change with pneumatic locking (ISO 30) - Pneumatic rotation of the work table 0° to 90° to 180° - Mobile control console with PC, 24'' - No.4 pneumatic vices with manual positioning and double pressure with safety valves - Manuallly adjustable profile reference stops on right and left of work table - Minimum quantity lubrication (MQL) with pure oil - Perimeter safety casing on 3 sides and retractable front door - FST CAM 4 program Optional equipment installed on the machine: - PR204851 5-position automatic tool magazine (ISO 30) - PR207680 4-vice Easy-to-Set configuration: • Transformation of standard vices into vices with automatic movement and pneumatic locking • 2 retractable pneumatic side stops • SW for vice positioning - PR-28965 Beam rotation stop for intermediate angles with manual adjustment - PR204833 External stop with tunnel - PR202971 Data import software for data in accordance to FOM protocol with wireless bar-code reader - PR-27602 Tool set for aluminium - QN-28849 ISO 30 cone with milling cutter Ø 75 mm thickness 6 mm for end milling Dkjdpfx Aajhlkqps Nsl

Condition: new, Year of construction: 2023, Corner crimping machine FOM INDUSTRIE BAIHA L Machine in stock - Max. profile height 200 mm - Hydro-pneumatic drive - Three pneumatic clamps - Min/max height of blade position from 0 to 180 mm - Kit for profile support - Digital counters for profile positioning - No. 2 right tool-holder - No. 2 left tool-holder - No. 2 knives 2 mm thickness - No. 4 tools 5 mm thickness - No. 2 fold-away profile fences Dkedpfsd E Eimjx Aa Nsl

Condition: like new (used), Year of construction: 2019, functionality: fully functional, 5 axis double head sawing machine FOM INDUSTRIE KEOPE E5 6.6 m Year: 2019 Condition: excellent, as new Equipment (standard + options): - No.2 carbide tungsten saw blades Ø 600 mm - Minimum cutting capacity between two heads: 470 mm (with heads at 90°) - Maximum cutting capacity between two heads: 6.6 m - No.4 vertical vices and No.2 horizontal (for step-by-step operation) - Micro-drop pure oil blade lubrication system Dkodewk R A Depfx Aa Nsl - Set up for the extraction of chips and fumes - Blade motors, three phase 5 HP (3.7 kW) - 230/400 V- 50Hz. Blade rotation speed 2400 RPM - Head rotation between 22.5° and 140° (Y and Z axes) with electronic control (vertical axis) - Internal blade inclination between 90° and 45° (W and U axes) with electronic control (horizontal axis) - Handling of mobile head (X axis) with electronic control - Mobile head max. speed 25 m/min. - Hydraulic saw blade feed (adjustable blade exit speed - quick return) - Profile lifting kit - Loading roller conveyor length 2.2 m, width 400 mm (on mobile head) - No.3 intermediate pneumatic retractable support - Chip conveyor belt - Label printer - FSTCut software - Software for special cut-off (beyond measure and super minimum) and profile bevel cut for 45° cuttings - Step-by-step cutting software, complete with 1 extra surface on fixed head, 90° cuts, two-hand control - Vacuum cleaner

Year of construction: 2025, condition: new, XX100292 New CNC Machining centre with 4 controlled axes FOM INDUSTRIE FMC 470 Machine in stock and ready for shipping Standard configuration: - Liquid-cooled electrospindle 7 kW, 20,000 rpm (HSK-F63) Dedeiv Imnopfx Aa Njkl - 9 location tool magazine on head (HSK-F63) - No. 2 pairs of pneumatic vices with positioning through the travelling column - No. 2 pairs of low profile jaws for clamping wide profiles - Left pneumatic reference stop - Minimum quantity lubrication (MQL) with pure oil - Central automatic greasing system and device for manual greasing - Chip and waste collection tank in base - Perimeter guard system with automatically opening, front retractable doors - X FLOW (automatic orientation of lubricant nozzles) - Control: POWER-D - Movable control console - 24” display - FST CAM 4 program Optional equipment installed on the machine: - PR202941 Fixed tool magazine for 8 positions in the center on the machine base - PR202962 Device for checking the integrity and measuring tool length - ZR204058 Pendulum mode with multiple workpieces (2 work areas, 4 workpieces) and processing of non-standard lengths with X-PAL: • Two pairs of additional vices with independent positioning • Transformation of std vices into vices with independent positioning • LED bar • Profile positioning software • Software for viewing the progress of the processing cycle • Device for measuring profile length • Second X-FLOW • Right pneumatic reference stop • Pendulum control software • Safety devices for pendulum processing • Tunnel for oversized profile machining • Software to manage oversized machining operations • ''Clock'' time calculation module program - PR202971 Data import software in accordance to FOM protocol and wireless optical bar code and QR code reader - ZP715010 Module for rigid tapping and chase tapping - PR202957 Hinged belt conveyor with ramp - PR203389 Rear chip collection tank - PR202975 Tool set A3/HSK F63 - PR202967 Angle head with vertical disc Ø 230 mm - PR202968 Cone with horizontal disc Ø 250 mm - PR204497 Holder HSKF63 with cutter Ø 200 x 6 mm - PR203072 Software adjustment of the vice pressure 3,5 - 7 bar - ZP714611 License for the office version of FST CAM 4

Condition: new, An additional aircompressor are required to enable the nitrogen generator to produce nitrogen. Nitrogen purity: 99.999% Input pressure: 8Bar Output pressure: 7Bar Power: 75W(Power is the cost per hour to produce nitrogen ) 3 în 1 design, no need for extra air compressor and refrigerator or dryer Gas clean Djdjxfrv Ejpfx Aa Nekl Price is EXW (Stock Europe), Include loaded on truck. Transport, installation, commissioning, training, and yearly service contracts are available upon request for an additional fee. Installation and training is always done by our high qualified Service team in 3 locations in Europe. Netherlands, Germany, Romania. Official Seller CNC Top Ten bv Coevorden, Netherlands

Year of construction: 2007, condition: good (used), - Used machine - Saw blade: 400 mm - Saw blade tiltable 0° left to 0° right - Hydropneumatic saw blade feed - Horizontal and vertical clamps - Motor power: 1.8 kW / 400 V - Cutting width: 242 mm Dedpfxjy E Itpj Aa Nokl - Cutting height: 140 mm - Incl. measuring roller conveyor 4000 mm - With digital readout and handwheel - Ex-stock, loaded free of charge

Condition: good (used), Year of construction: 2003, travel distance X-axis: 14,000 mm, travel distance Y-axis: 4,000 mm, travel distance Z-axis: 1,500 mm, spindle speed (max.): 2,500 rpm, feed length W-axis: 900 mm, spindle diameter: 152 mm, FPT MAR-X 3, 2003 CNC SELCA 4045 PLUS DIGITAL, Built 2003, CNC can be changed to Heidenhein 620. FPT TRT25. Rotary Table, 25 Ton. Two axis Head, 144 x 144. X, Column travel 14.000 mm Y, Headstock vertical travel 4.000 mm Z, Ram stroke 1.500 mm W, Spindle Ø 152,4 mm 900 mm Spindle taper ISO 50 Spindle speed 0 - 2.500 rpm Spindle motor 48 kW Automatic tool changer 40 Tools FPT TRT25. Rotary Table, 360.000° 2.500 x 2.500 mm Dedswdm A Hopfx Aa Njkl Rotary Table longitudinal travel 2.000 mm Table load 25 Ton

Condition: used, Year of construction: 2007, functionality: fully functional, travel distance X-axis: 3,100 mm, travel distance Y-axis: 2,000 mm, travel distance Z-axis: 1,000 mm, spindle speed (max.): 3,000 rpm, table length: 1,800 mm, table width: 2,000 mm, feed length W-axis: 700 mm, workpiece weight (max.): 12,000 kg, milling spindle length: 700 mm, FPT CASTEL RED HEIDENHEIN TNC 430. Built in 2007. X=3100mm Y=2000mm Z=1000mm Dkjdpfx Ajwdiu Eea Njl Table 2000 x 1800 mm, 12 Ton Cooling through spindle. X Column travel 3,100 mm Y Headstock vertical travel 2,000 mm Z spindle stroke 700 mm W Column in spindle direction 1,000 mm Spindle diameter 130 mm Spindle diameter ISO 50 Spindle speed 3000 rpm Spindle motor 37 kW Rotary table size 1,800 x 2,000 mm Table load 12 tons C-axes 360,000°