CNC turning and milling center

Mazak QUICK TURN Nexus 350M

Condition: good (used), Year of construction: 2007, max. wheel diameter 400 mm gear width 250 mm max. module 8 min. module 0,5 root circle diameter 10 mm number of teeth 5 - 999 ical angle +/- 45 ° weight 12.5 t With Hoffmann filter system: Year of manufacture: 2006 Filter no. 05919 - Type HSF 100 SEK • Grinding wheel flange • 1 grinding wheel Fjdpfx Adeyclrpsaefw • 1 original dressing device • 1 set of dressing wheels • 1 sensor -> Very good condition, only 22,500 operating hours

Condition: ready for operation (used), Year of construction: 2019, total height: 2,797 mm, overall weight: 1,570 kg, This 3-axis ZEISS Contura 7/10/6 RDS was manufactured in 2019 and features a robust motorized CNC drive system with a maximum vector speed of 465 mm/s. It includes the ZEISS RDS-C articulating head and VAST XXT TL3 sensor, capable of scanning speeds up to 150 points/second. Ideal for precise measurements with a maximum workpiece weight of 730 kg. Consider the opportunity to buy this ZEISS Contura 7/10/6 RDS CMM machine. Contact us for more information about this machine. Additional information • Maximum workpiece size: approx. 1344 x 910 x 716 mm • Maximum workpiece weight: 730 kg • Table height: 850 mm • Equipped with vibration damping system • Sensor System: • Articulating head: tilt ±180°, rotation increments 2.5° • Scanning speed: up to 150 points/second • Max. stylus length: 150 mm • Max. stylus weight: 15 g • Min. stylus tip diameter: 0.3 mm • Accuracy (per ISO 10360 standards): • Length measurement error (E₀): 1.7 + L/350 µm (at 18–22°C) • Scanning error (THP): 2.7 µm • Form measurement error (RONt): 1.7 µm Ffsdpfex D Ngfjx Adaow • Repeatability (R₀): 1.2 µm • Controller: ZEISS C99L • Software: ZEISS CALYPSO, ZEISS GEAR PRO, ZEISS HOLOS • Control mode: Motorized / CNC • Interface: Ethernet, USB • Performance: • Drive system: Motorized CNC • Travel speed (axes): 0–70 mm/s • Max. vector speed: 465 mm/s • Max. acceleration: 1.85 m/s² • Scanning speed: up to 125 mm/s • Utilities: • Power supply: 100–240V AC (±10%), 50–60 Hz • Max. power consumption: 800 VA • Typical power usage: 200 W • Compressed air: 6–8 bar, pre-cleaned, dry (ISO 8573-1 Class 4) • Air consumption: max. 120 Nl/min • Environmental Conditions: • Operating temperature: 18°C–22°C • Relative humidity: 30–60% (non-condensing) • Compliance & Certifications: • Conforms to EC Machine Directive 2006/42/EC • EMC Directive 2014/30/EU • Quality management: ISO 9001:2008 • Environmental management: ISO 14001:2004 • Accredited ISO / IEC 17025:2005 Dimensions Machine Depth 1975 mm

Condition: reconditioned (used), Year of construction: 2006, CNC Universal Milling & Drilling Machine DECKEL MAHO DMU 80 P duoBlock With MILL PLUS iT path control system Year of manufacture: 2006 Travel paths: X 800 Y 800 Z 800 mm Spindle speed range: 0 – 8,000 rpm, stepless (SK 50) Including the following accessories: - NC rotary table, 900 mm x 700 mm clamping surface (maximum table load 1.4 t) Fjdpexn Aczjfx Adasfw - Universal milling head with controlled B-axis - Universal tool changer with 40 magazine stations, double gripper (SK 50) - Fully enclosed guard cabin with sliding doors and interior lighting - ICS – 40 bar (internal coolant supply) - Chip conveyor - Rotoclear - 3D tactile probe Heidenhain TS 641 - Operating modes 3 + 4 - Electronic handwheel - 50 pcs. tool holders SK 50 - 3 height-adjustable machine feet - Transport device - Operating manuals

Condition: used, Year of construction: 2015, machine/vehicle number: A2536805, pressure:40 t stroke:250 mm return capacity:6,3 t Ffjdpfx Asfxyhfodaow motor:5,5 kw Max Working height:450 mm :90 mm/sec. :10 mm/sec. spindle stroke:250 mm pestle plate:500 x 200 mm table plate:600 x 650 mit T-Nuten mm Table cut-out:200 x 170 mm table height:850 mm :200 l

Year of construction: 2003, condition: good (used), Strokes 560x 410 x 510 mm, table 900 x 410, magazine 30 tools, spindle 12.000 rpm, chip conveyor Ffsdpfx Asiwkhksdaew

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, CNC Tool Grinding Machine Walter Helitronic Power FH, Year of manufacture: 2015 Fanuc control system with cylindrical pallet loader, pallets from 4 mm to 25 mm 8-position disc changer, electrostatic mist collector Ffjdpfxoyh Dl Ne Adasw fire extinguishing system, Software: Walter Window Mode and Toolstudio, Software packages: 001, 002, 003, 016, 017, 026, 090, 091, 098, 099, 032, Helicone, Helidrill, Heliflute, NC-Mode, Power-IMS, Toolstudio_Standard, with preparation for hydraulic unit (steady rest), The grinding spindle (single spindle) is directly driven and equipped with an oil cooler. The hollow shaft motor for the A-axis operates at a speed of 0-750 rpm. The C, X, Z, and A axes were overhauled in 2022.

Condition: used, CNC Press Brake AMADA Type HFBO 50 x 2000 Serial No. HFBO 50 20 S60906 Year of manufacture: 1996 Press brake with 8 axes - CNC control Operator II Pressing force: 50 tons Working length: 2090 mm Stroke: 200 mm Frame depth: 420 mm Distance between side frames: 1660 mm Max. tool installation height: 460 mm Table width: 60 mm Table height above floor: 910 mm Motor power: 4.5 kW Mains connection: 400 Volt, 50 Hz, 20 Amp. - 8-axis CNC control Operator II (Y1-Y2 / X1-X2 / Z1-Z2 / R1-R2) - 2 freely programmable backgauge fingers, movable laterally and in height (Z1+Z2+R1+R2) - Press beam with servo valves and measuring system Y1 and Y2 Fjdpfx Ajw Iq Ugsdaofw - Operation via electric foot switch and/or two-hand control panel - Mechanical lever-style tool clamping for the upper tool (5 AMADA Expert, 5 UKB 50.667 H=120 mm) - Tool holder for lower tool, 60 mm wide - 11-piece upper tool set, 30°, total length 1675 mm - consisting of: 1x 835 / 1x 300 / 1x 165 / 1x 50 / 1x 45 / 1x 35 / 1x 20 / 1x 15 / 1x 10 / 2x 100 mm (end pieces) in length - 2-piece lower tool, 88° - V8, total length 1250 mm - consisting of: 1x 835 / 1x 415 mm in length - Indicated operating hours: 30,537 h - Operating manual, electrical diagram, spare parts book included Weight: 4,700 kg Good condition

Condition: good (used), Year of construction: 1989, operating hours: 64,136 h, Centre height: 350 mm Turning length: 1000 mm Max. swing diameter over bed cover: 600 mm Max. swing diameter over cross slide: 360 mm Spindle bore: 107 mm Speed range: 16 – 3150 rpm Feed range longitudinal & face: 0.5 – 5000 mm/min Rapid traverse longitudinal & face: 9 m/min Fsdpfxsvr Eh Eo Adasfw Main drive: 30 kW Dimensions of machine with chip conveyor (L x W x H): 5400 x 2200 x 2000 mm Weight: 6400 kg Accessories / Special features: • CNC control GILDEMEISTER EPL 2 with TFT display General description: CNC manual input control system with program entry via function and numeric keypad. All information is entered in dialogue with the screen. Integrated menu technology with plain text display of all functions. Operator keypad, display, and electronic handwheel located within a separate chip guard housing. The EPL control offers the following capabilities: • Direct interactive program entry and editing by the operator through the EPL control without manual technological preparation • NC programs in ISO/EIA format can be entered, output, or manually keyed in via the RS 232 serial interface Machining cycles: • Removal cycles for longitudinal, facing, and contour turning, including with allowance • Thread cutting • Undercuts as per DIN 509-Form E and F and DIN 76; grind stock programmable • Axial and radial grooves as per DIN 471 and 472, including bottom finishing • 90° radii and 45° chamfers • Automatic cutter radius compensation for cycles, undercut, groove, radius, chamfer Programming: • Block-orientated, metric/inch, diameter for absolute entry, radius for incremental entry • Full circle programming, subroutine technology, hide levels for program sections, zero point offset, mode selection via menu Program entry and output: • Interactive via guided menu or direct in dialogue • Hydraulic 3-jaw chuck Ø 315 mm with through spindle bore Ø 80 mm • Hinged chip conveyor • 12-position tool turret VDI 40, 6 standard stations + 6 driven tool stations • Coolant system • RS 232 interface • Electronic handwheel • Electric foot switch for 3-jaw chuck and tailstock quill • Lighting • 12 various standard toolholders (to be finalized on site) Overhauled servo drive for main spindle, 06/2025 Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: refurbished (used), Overhauled Mazak main spindle for VTC 200 or VTC 300 for sale. The spindle has been fully overhauled, spindle bearings and intermediate sleeves have been replaced. The taper has been reground. Subsequently, it has been balanced. The maximum speed is 12,000 rpm. We have additional overhauled Mazak spindles in stock; feel free to send us your inquiry. This is an exchange spindle, meaning a core return is required. If you have any further questions, we are at your disposal. Ffjdpovdkdiefx Adasw

Condition: refurbished (used), functionality: limited functionality, Year of construction: 2003, operating hours: 24,000 h, pipe diameter (max.): 100 mm, pipe length (max.): 4,100 mm, bending angle (max.): 183 °, bending radius (max.): 300 mm, wall thickness: 8 mm, Transfluid DB 2090 DB CNC Mandrel Tube Bending Machine. Excellent High Quality Germany Machine, with fully refurbished main hydraulic pumps and main head fully reconditioned. Only requires new encoder to be fitted and this machine is ready to go. Features include. 100mm x 1.6mm Tube Maximum Capacity at 1.5D Anticipated Mandrel Withdrawal Fully automatic setup of clamps and follower Boosted Follower for tight radius thin wall tube bending. Long bed with 4000mm over mandrel. Comes with huge amount of tooling worth over AU$150k. Tooling Included: 101.6mm 152mm CLR 101.6mm 200mm CLR 76.2mm 114mm CLR 76.2mm 200mm CLR 76.2mm 238mm CLR 63.5mm 96mm CLR 57.2mm 86mm CLR 50.8mm 76mm CLR 44.5mm 67mm CLR 40 x 40 120mm CLR 50 x 50 150mm CLR Fodpfxotrd T To Adasfw 60.3mm 150mm CLR 48.3mm 120mm CLR