Used Eisele Vms Ii for sale (118)

Year of construction: 2009, condition: used, Sawing system for aluminum with 2 saw motors that independently perform a 45° cut. Pedeqzmnuspfx Abhspu Material feed unit with up to 8,100 mm Cross conveyor, storage table, chip conveyor and extraction Soundproof cabin Control via Siemens S7 panel Operating instructions etc. available, further technical data on request Machine was in operation until dismantling Further technical data on request or see photos

Condition: like new (used), Year of construction: 2023, operating hours: 1,809 h, functionality: fully functional, machine/vehicle number: 1559, saw blade diameter: 550 mm, feed length X-axis: 800 mm, total length: 2,400 mm, total width: 2,000 mm, total height: 1,800 mm, cutting range round steel at 90°: 190 mm, type of input current: three-phase, rotational speed (max.): 2,850 rpm, cutting height (max.): 150 mm, overall weight: 1,650 kg, section length (min.): 3 mm, section length (max.): 4,000 mm, saw blade speed: 2,850 rpm, input voltage: 400 V, saw drive: 7,500 W, cutting diameter: 270 mm, saw blade bore: 40 mm, Circular Saw Fully Automatic PROFILMA 502 + Chip Extraction MG 3 ST Circular Saw Fully Automatic PROFILMA 502 Ppedpfey Dtpmsx Abhou Fully automatic operation, 7.5 kW drive, S6, 400 V, 50 Hz, 2850 rpm. Suitable for saw blades Ø 550 mm, cutting capacity 270 x 150 mm (width x height), Ø 190 mm. Max. profile width 270 mm. Equipped with Siemens S7 controller with touch display incl. piece counter. Includes CPU 315 and Flexisoft, batch multiplier for bundle material processing. Cycle time indication in seconds, chain dimensions, includes reversing device for cut lengths up to 4 m max. Automatic shut-off via limit switch at end of material, fault diagnostics, including IXON router for VPN connection (see datasheet). Motorized saw blade feed, steplessly adjustable, vertical and horizontal clamping from bottom to top (both on feed and discharge side of saw head). Cutting gap extension on both sides of the saw blade. Electronic material feed unit with 800 mm feed length, utilizing ball screw and servomotor, including pneumatic horizontal and vertical clamping system. The profile support area in the feed zone is equipped with a lift/lower roller. Remnant cut from 75 mm, profile-dependent. Clamping pressure reduction horizontally and vertically with 6 pressure regulators. Intermittent spray device with level monitoring and automatic shut-off, 1-liter lubricant reservoir. Noise protection package—frame interior lined with soundproofing mats. Two extraction nozzles Ø 100 mm. Safety guard over both the saw head and the feed unit. 740 mm roller conveyor with intrusion guard on the infeed side, 450 mm pertinax tabletop with intrusion guard on the outfeed side. MG 3 Chip Extraction Dust and chips are collected in a 172-litre metal container, which is removable for easy emptying. Two outlets with 100 mm hose adapters (no extraction hose included). 3.0 kW drive, 400 V, 50 Hz, three-phase motor. Max. air flow rate 2,600 m³/h, vacuum 30 mbar, with fan snail housing above the extractor. Large filter surface, pneumatic shaker unit for filter cleaning, filter class M. Max. noise level 80 dB(A). Selector switch for continuous operation or saw-controlled operation (no power cable). Painted: RAL 7035 / 9016.

Condition: good (used), Year of construction: 1996, CUTTING RANGE ..... MIN 10MM TO 75MM CUTTING LENGTH ..... 5-900 SINGLE STROKE -9999 REVERSE RUN CUTTING SPEED ..... 0 - 40 MM SEC. INFINITELY VARIABLE REVERSE 135MM/S MATERIAL FEED SPEED ..... MAX. 350 MM/S Pedpfx Asquuufjbhjpu TENSION FORCE ..... MAIN CLAMP 10500N

Year of construction: 2009, condition: used, Drive with 3 milling motors ensures a very stable structure (steel profiles can be machined from 3 sides in a single clamping). Locking mechanism for the lift of the horizontal motors prevents profiles from being scratched when inserting and removing them. Processing of profile widths up to 300 mm possible (e.g., mailboxes) using only the vertical milling motor. Specification: - Equipped with 1 vertical and 2 horizontal milling motors - Pneumatic workpiece clamping with 2 horizontal clamping cylinders - 3 pneumatic spray nozzles - Milling area of the vertical motor (L x D): 365 x 230 mm Ppedpfx Asy Nm Ersbhsu - Milling area of the horizontal motors (L x H): 250 x 100 mm - Maximum profile height: 150 mm - Operation via switches and 4 hand levers

Condition: ready for operation (used), Year of construction: 2013, Circular Metal Saw manufactured in 2013. This PRESSTA EISELE Profilma 400 V features a saw blade diameter of Ø400 mm and a powerful motor with approximately 12 kW. It offers automatic material feeding and a pneumatic clamping system for efficient operation. If you are looking to get high-quality cutting capabilities, consider the PRESSTA EISELE Profilma 400 V machine we have for sale. Contact us for further details regarding this machine. • Design: Integrated material feed/loading magazine; floating feed to compensate for profile deviations • Power supply: 400 V / 50 Hz • Materials: Aluminum and non-ferrous metal profiles • Saw blade diameter: Ø400 mm • Saw blade speed: adjustable approx. 3,500–5,800 rpm • Saw movement drive: Servo motor with ball screw drive • Sawing direction: Linear feed from top to bottom • Cutting principle: Crosscut • Material feed: Automatic servo feed with repeat strokes for longer cutting lengths • Material separation: Before the saw blade retracts (no recutting) • Clamping system: Pneumatic, vertical and horizontal, on both sides of the saw blade; clamping force separately adjustable; replaceable plastic/PVC pads • Control: PLC-based; operation via control panel with display Pedpeyyxxfefx Abhjpu • Functions: Profile database; piece counter (incl. bundle cutting); cycle time display; diagnostics and error messages; machine status indicator • Saw blade lubrication: Minimum quantity lubrication (spray mist), programmable lubrication control • Extraction connections: Ø100 mm and Ø160 mm • Pre-installation: Prepared for external chip extraction • Motor Power: up to 22 kW (multi-speed motor: 3.5 / 11.5 / 18.5 / 22 kW) Additional equipment • External chip extraction unit (to connect to Ø100/Ø160 mm ports)

Year of construction: 2019, condition: excellent (used), functionality: not functional, Compact hydraulic C-frame punching machine with 160 kN punching force for precise applications on smaller profile cross-sections. The torsion-resistant frame design ensures accurate punching in aluminium, steel or plastic. Psdpoy Agqnofx Abhopu

Year of construction: 1996, condition: used, Hydropneumatic operation Punching force: 50 kN Work hub: 35 mm Overhang: 110 mm Podoyxpw Nspfx Abhjpu Installation height: 140 mm

Condition: excellent (used), Mitre saw in excellent condition Ppsdpeyw Tg Ejfx Abhju

Condition: excellent (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: 1015, profiles with dimensions (HxB) up to 100x195mm, 80x200 mm automatic work cycle driven by a 3 kW/400 V, 2850 rpm motor cutting disc d=450x3.8x40mm, z=110 Ppedpfswgmv Sex Abhsu horizontal and vertical material clamping on the feed side dosing spray system horizontal material clamping in the feeder moving both clamping jaws when retracting (prevents scratching of the profile) infinitely adjustable hydropneumatic cutting disc feed cutting disc exiting from the rear length of cut sections adjustable in the range of 0-300mm (with reversing device 0-600 mm) setting the cutting length by a handwheel with a mechanical counter maximum width of the cut profile 200 mm cutting range (height x width) 100x195mm, 80x200mm automatic shutdown when material runs out possibility of connecting a dust extractor

Year of construction: 2009, condition: used, Saw blade diameter vertical: 600 mm Pjdpfeywtqdsx Abhopu Saw blade diameter (horizontal): 500 mm Ejecting width: processing of profiles up to 300 mm at 90°, mitre tips up to 30° Profile height max. 280 mm Engagement depth: at 90° horizontal up to 185 mm / at 90° vertical up to 230 mm Material stop: swiveling 30° - 90° - 45° Material stop adjustable with detent points and display on the display Program control for automatic adjustment of the punch height, the angle, and the punching height Up to 6 programs can be stored Hydropneumatic material feed via 2-hand operation Pneumatic material clamps coolant lubrication

Year of construction: 1967, condition: used, machine/vehicle number: 9317, disk of circular saw-Ø: 275 mm cutting area at 90°: 120 x 75 mm cutting area at 45°: 90 x 65 mm rotations of disk: 2000 rpm engine: 380 V, 1,1 kW Ppsdpfx Abob N Eicshju space needed: 700 x 900 x 1000 mm

Condition: used, Year of construction: 2001, Hydropneumatic operation Profile height: 210 mm under hold-down Max. stamping height with double-adjustable punching heads: 145 mm Abutment height: 150 mm Ppedpfxsyu Rzte Abhsu Weight: approx. 400 kg

Condition: used, Year of construction: 2009, Hydraulic operation Profile height up to 210 mm under hold-down Podpfeyu Rw Isx Abhopu Max. stamping height with double-adjustable punching heads: 145 mm Abutment height: 150 mm Weight: approx. 450 kg

Condition: used, Year of construction: 1998, Hydropneumatic operation Profile height: 180 mm under hold-down Max. insertion height: 145 mm Abutment height: 150 mm Weight: approx. 400 kg Ppjdpfx Aeyrrddjbhju

Condition: used, Year of construction: 1995, Hydropneumatic operation Ppedoyrrbvepfx Abhju Profile height: 180 mm under hold-down Max. insertion height: 145 mm Abutment height: 150 mm Weight: approx. 400 kg

Condition: excellent (used), Year of construction: 1995, As-new notching milling machine from a training workshop Siegfried Volz Machine Tools Rüschebrinkstr. 151-153 Podpfxeyrh Rge Abhjpu DE - 44143 Dortmund - Wambel / Germany

Condition: used, Year of construction: 2011, Hydropneumatic operation Profile height: 200 mm below hold-down Max. punching height: 150 mm Abutment height: 150 mm Ppjdpfeynaluox Abheu Weight: approx. 400 kg

Year of construction: 2006, condition: good (used), for processing aluminium and PVC profiles in facade and structural construction Mitres in 3 planes, also suitable for use as a compound crosscut saw Ppodjyz T A Ujpfx Abhou Processing of profiles up to 300 mm width at 90°, sharp mitres up to 30° Notching depths horizontally up to 185 mm and vertically up to 230 mm at 90° Notching width at 90°: 300 mm, profile height up to 280 mm Motorised height adjustment for notching, positioning with electronic digital display Saw blade swivel range vertical 60° - 90° - 25° (front/centre/rear), motorised positioning with electronic digital display Saw blade swivel range horizontal with vertical blade 45° - 90° - 45°, motorised positioning with electronic digital display

Condition: good (used), Year of construction: 1995, machine/vehicle number: 9131, Offer 26050 Technical data: - Saw blade dimensions - vertical 400 x 3.5 x 40 mm - - horizontal 400 x 3.5 x 40 mm - Notching area / notch depth vertical 135 mm - Notching area / notch depth horizontal 105 mm - Notching width at 90° up to 280 mm - Notching width at 30° up to 100 mm - Vertical saw blade manually swivellable from 90° - 30° via hand wheel - Usable as a shifting saw without horizontal saw blade - Profile stop shoulder swivellable 30° - 90° - 30° - Pneumatic material clamp Psdpfx Ajyz Tqrobhopu - Coolant spray device - Air connection 6 bar - Drive 400 V / 2 x 2.2 kW / 2800 rpm - Space requirement approx. W 2200 x H 1600 x D 1400 mm - Weight approx. 800 kg

Year of construction: 1995, condition: good (used), machine/vehicle number: 8883, Offer 26051 Technical Specifications: - Feed of the milling unit manual - Worktable height adjustable via handwheel - Horizontal and vertical material clamping - Cutter diameter up to 300 mm - Max. milling height 150 mm - Max. milling depth 110 mm - Max. milling length 500 mm - Angle-adjustable stop left & right 20° - 90° - Spindle speed 2800 rpm Psdpfx Aboyz S Trohjpu - Drive 400 V 2.2 kW - Compressed air connection 6 - 8 bar - Air consumption per cycle 10 l - Pneumatic profile clamping - Spray device - Space requirement approx. W 1300 x H 1450 x D 1100 mm - Weight approx. 300 kg

Condition: as good as new (ex-display), Year of construction: 2018, saw blade diameter: 5,50,500 mm, Machine in perfect technical condition. Practically very little used. For processing aluminum and PVC profiles. Mitres possible in 3 levels and can be used as a splitting saw, manual adjustment of the horizontal saw blade by a maximum of 20 mm in front of the vertical saw blade. Psdpfx Aovtarnebhspu Notch options: rectangular, one-sided diagonal, two-sided diagonal, three-sided diagonal. Processing of profiles up to 300, width up to 90 °, bevels up to 30 °. Notch depth horizontally up to 185 mm, vertically up to 210 mm at an angle of 90 °. Notch width at 90 °: 300 mm, profile height 280 mm Manual adjustment of the notch and height, positioning using mechanical digital displays. Vertical saw blade rotation range 30° – 90° – 30°, (front/middle/back) manual, positioning via digital display. Vertical saw blade rotation range 30° – 90° – 30°, manual, positioning via digital display. The material stop (table top) can be manually rotated left and right within the range of 30° - 90° - 30°, positioning via measuring scale. The material depth stop can be manually adjusted via the sliding carriage and manual clamp, positioning via digital display.

Condition: used, Year of construction: 1994, functionality: unexamined, machine/vehicle number: 171982, saw blade diameter: 350 mm, main saw diameter: 350 mm, We offer this used EISELE LMS 350 P cut-off saw, year of manufacture 1994. Manufacturer: EISELE Model: LMS 350 P Serial number: 171982 Year of manufacture: 1994 Voltage: 380 V With double-button control and pneumatic clamps Ppodpoy D H Dwefx Abhju Equipped with a wood blade If you have any questions or need further information, please feel free to send us a message or give us a call.

Condition: excellent (used), Year of construction: 1994, functionality: fully functional, Type: AKF 250 Motor: 400V 2.2kW Speed: 2800 rpm Cutter diameter: 250 mm Cutter arbor diameter: 40 mm Podsygdf Aopfx Abhjpu Milling width: 300 mm Milling depth: 85 mm Profile height: 160 mm Weight: approx. 150 kg Dimensions (W x H x D): 950 x 1450 x 930 mm

Condition: used, Year of construction: 2008, Behringer Eisele HCS 150, year of manufacture 2008, feed magazine, cut-off disposal. The machine is operational and can be purchased in its current condition or fully reconditioned by us including assembly. Type: HCS 150 Machine number: Type no.: 49600H0024 Year of manufacture: 2008 Weight: 4,500 kg Required space: 9.3 m x 7.5 m Control: Siemens PLC control Round material (max.): Ø 150 mm Psdpsxpd D Nsfx Abhjpu Flat material (max.): □ 135 mm Saw blade feed: 0.5 - 40 mm/min Compartments incl. roller conveyor: 11 units Single compartment load: max. 500 kg at 3 m bar length Total load capacity: 4,000 kg Conveyor manufacturer: Geppert Conveyor length: 1,500 mm Conveyor width: 400 mm Conveyor speed: 6.3 m/min Total power requirement: approx. 34 kW Voltage: 400 V Air connection: 6 Bar

Condition: used, Hydropneumatic operation Max. punching height: 90 mm Ppjdpow Inudefx Abhou Abutment stroke: 100 mm Punching stroke: 20 mm Pressing force: 30 kN Max. profile height: 100 mm Weight: approx. 280 kg