Used Integral Stops for sale (14,260)

Condition: ready for operation (used), Year of construction: 2001, operating hours: 27,267 h, functionality: fully functional, turning length: 180 mm, turning diameter: 100 mm, spindle bore: 43 mm, spindle speed (max.): 6,000 rpm, travel distance X-axis: 125 mm, travel distance Z-axis: 195 mm, TECHNICAL DETAILS Turning diameter: 190 mm Turning length: 180 mm Max. turning diameter: 100 mm Travel X-axis: 125 mm Travel Z-axis: 195 mm Rapid traverse X-axis: 15 m/min Rapid traverse Z-axis: 20 m/min Spindle bore: 43 mm Spindle bearing diameter: 80 mm Spindle speed range: 60–6,000 rpm Tailstock diameter: 40 mm Tailstock taper: MK 3 Tailstock travel: 45 mm Number of tool positions: 10 MACHINE DETAILS Transformer: 400 V / 200 V Data interface: V.24 / RS-232-C Operating hours: 27,267 h EQUIPMENT Bar feeder Integrated CNC control Space-saving, compact design Inductively hardened flat guideways for bed and carriage Continuously variable AC main spindle drive Constant cutting speed programming Integrated cold light Ammeter for main spindle drive Swiveling central control panel Controls for automatic, manual, and CNC programming modes Three-phase servo motors for X and Z axes Backlash-free, pre-tensioned precision ball screws for X and Z axes Automatic central lubrication with electrical monitoring Rcsdpfxjzul T Ns Abpef Coolant system with tank, pump, lines, and spray nozzle Electric 10-position turret system, MORI SEIKI Automatic turret indexing logic Direct coolant supply through the turret disk Fixed hydraulic unit for power chuck Front sliding door with large viewing window Electrical connection for chip conveyor, prepared Electrical equipment according to VDE 0113 Attached control cabinet Freestanding transformer

Condition: ready for operation (used), Year of construction: 2003, operating hours: 4,256 h, functionality: fully functional, turning length: 570 mm, turning diameter: 176 mm, travel distance X-axis: 245 mm, travel distance Z-axis: 570 mm, controller model: MSG-805 V, TECHNICAL DETAILS Turning diameter: 176 mm Turning length: 570 mm Swinging diameter: 510 mm Machining diameter: 420 mm Travel X-axis: 245 mm Travel Z-axis: 570 mm Rapid traverse X/Z-axis: 24 m/min Spindle bore: 43 mm Spindle speed: 60–6,000 rpm Tailstock diameter: 85 mm Tailstock travel: 120 mm Rcodpezul Tvsfx Abpsf MACHINE DETAILS Control system: MSG-805 V Total power requirement: 5.5 kW Dimensions & Weight Footprint: approx. 2,000 × 1,700 × 1,800 mm Machine weight: approx. 3,400 kg Operating hours: 4,256 h EQUIPMENT Integrated CNC control system Inductively hardened flat guides for bed and cross slide Continuously variable AC main spindle drive Programming of constant cutting speed Integrated cold light Power meter for main spindle drive Operator controls for automatic and manual operation CNC programming and control panel Tailstock with hydraulically actuated quill, MK 4 Continuously variable quill pressure Programmable actuation of the tailstock quill via toggle switch and M function High-dynamic three-phase servomotors for X and Z axes Backlash-free, pre-tensioned precision ball screws for X and Z axes Automatic central lubrication with electrical monitoring Coolant system with tank, pump, lines, and nozzle Electric 12-station turret system MORI SEIKI Automatic direction logic on the turret Direct coolant supply through the turret disk Fixed hydraulic unit for power chuck Full enclosure of the work area Front sliding door with large viewing window Electrical preparation for chip conveyor Electrical equipment according to VDE 0113 Data interface V.24 / RS-232-C Mounted control cabinet Freestanding transformer: 400 V / 200 V

Condition: ready for operation (used), Year of construction: 2018, operating hours: 13,072 h, functionality: fully functional, working width: 2,500 mm, No minimum price – guaranteed sale to the highest bidder! The machine is in very good overall condition, both visually and technically. No visible damage, corrosion, or significant wear and tear can be detected. Maintenance was carried out internally using SAP PM (electrical maintenance every 6 months, mechanical maintenance every 3 months). TECHNICAL DETAILS Material: Continuous corrugated cardboard Working width max.: 2,500 mm Minimum length: 200 mm Cardboard thickness: 2.57 mm Tool width: approx. 45 mm Longitudinal cutting accuracy: 0.2 mm Length tolerance: 1.5 mm/m Packaging size: 600 × 600 × 300 mm Performance: approx. 55 s/packaging unit Software and control (with 21" multi-touch panel and integrated control cabinet) PC: Beckhoff C6930 (Intel Core i5, 16 GB RAM, SSD) with Windows 10 IoT Enterprise Software: Beckhoff TwinCAT 3 Packaging design database: approx. 250 designs Production list control Dynamic tool management Rsdozu Akropfx Abpjcf Multi-level waste optimization Bidirectional processing Remaining length monitoring Production data recording in CSV format Plain text error messages MACHINE DETAILS Operating hours: 13,072 h (in single-shift operation) Machine construction: Welded construction Multi-function tools for longitudinal processing: 6 Transverse processing tools: 1 Rubberized rollers: 2 Overpressure: segment-controlled Weight (according to nameplate): approx. 2,110 kg EQUIPMENT Automatic cardboard changer Automatic selection of the optimal cardboard web width Two stations for cardboard webs Box designer programming software for customer-side workstations Creasing, scoring, perforating, and cutting according to the single-point principle Material-friendly creasing technology to prevent the cardboard from flaking Perforation using an oscillating knife with adjustable perforation level Cutting using a toothed knife on a rubberized roller Clean, fiber-free cut edges Servo-motor adjustable tools Packaging designs Bottom/lid construction Bottom with corner locks for upright fixing of rims Lid according to FEFCO 0331 Suitable for the production of precisely fitting individual packaging for aluminum and forged wheels

Condition: ready for operation (used), Year of construction: 2019, operating hours: 12,568 h, functionality: fully functional, 4-axis Lathe – Universal | Brand: DMG MORI | Type: CTX alpha 500 V4 Year of manufacture: 2019 (Start-up: July 2029) (Version with Y-axis and driven tools) The machine can be inspected by appointment under power. Condition: Fully functional / ready for operation. Operating hours (week 34/2026): - Total operating hours: 12.641 h - Spindle hours: 2.605 h TECHNICAL SPECIFICATIONS / EQUIPMENT: - Turning diameter: 165 mm - Turning length: 500 mm - Main spindle as an integrated spindle motor, ISM 52 Synchro * Drive power (100/40% duty cycle): 13/14 kW * Speed range: 20 - 6.000 rpm - Partial hollow chuck (hydraulic) * Pull-tube internal diameter: 52 mm - C-axis and spindle brake (hydraulic) - Y-axis for cross slide: +/- 40 mm, stroke: 80 mm - Tool turret: 12-position, brand: Sauter * Tool holder: VDI 30 mount, DIN 69880-30 * Driven tools * Connection/drive to DIN 5480 - Direct measuring system on the X-axis - Tailstock Rcedpszvz Aisfx Abpjf - CNC control: Siemens SINUMERIK 840D sl Operate * User interface: CELOS / ERGOline * Programming: ShopTurn 3G - Hollow spindle stop, adjustable, mounted at the rear on a hollow chucking device, Ø 66 mm (chuck-independent) * Belt filter system, filter fineness 40 µm * Level monitoring - Mechanical oil mist separator - Special version, operating mode BA4 “emery operation” - Coolant spray gun - Chip conveyor (hinged belt), incl. coolant tank and coolant pump, - Coolant system: 8 / 20 bar, * Coolant tank: approx. 600 l (selectable via M-function, with supply through the turret disc to the turret stations) - DMG MORI NETSERVICE - DMG MORI IoTconnector (enables DMG MORI’s online services) - DMG MORI Service Agent (controlled machine maintenance and servicing) - Bar machining package D65, consisting of: * D66 hydraulic hollow-bar clamping device * Workpiece retrieval device, with conveyor belt, conveying to the left for parts up to max. D65 x 185 mm in length, max. workpiece weight 3 kg - Documentation - CE marking Machine dimensions (L x W x H): approx. 3.843 x 2.580 x 1.825 (Height including attachment: approx. 2.415 mm) Available as an option: Milling attachments, - Collet chucks, - Jaw chucks, - Tools No guarantee is given as to the completeness or accuracy of the technical specifications or the equipment. - Subject to prior sale -

Condition: reconditioned (used), Year of construction: 2016, operating hours: 345 h, functionality: fully functional, working width: 1,230 mm, area performance: 8,600 m²/h, overall weight: 1,944 kg, warranty duration: 12 months, water tank capacity: 310 l, sweeping width: 1,230 mm, HAKO SCRUBMASTER B310 R CL TB1230 SCRUBBER Rcjdpfx Asy Ui Akjbpsf NEW HAWKER PERFERCT PLUS 36V 640Ah TRACTION BATTERY (8PZS640) NEW NEOS 36V 100A CHARGER Manufactured in 2016 with 345 hours on the clock 1230mm cleaning head (TB1230) equipped with three new medium-hard disc brushes for work on any surface. Integrated pre-sweeper with new side brushes and a new cylindrical brush to remove loose dirt before the actual cleaning. New squeegee blades made of high-quality natural rubber are ideal for use on all surfaces. New protective rubbers around the brush head prevent water from splashing outside the machine's contours. The device is equipped with new, durable drain hoses and a new suction hose. New suction turbines ensure high water suction power from the squeegee blade. Each device we offer has individually taken photos; you get exactly what you see. TECHNICAL DATA: Working width (mm): 1230 Squeegee width (mm): 1260 Capacity (m²/h): 8600 Voltage (V): 36 Number of disc brushes (pcs): 3 Working speed (km/h): 7 Clean water tank capacity (l): 310 Dirty water tank capacity (l): 310 Weight without batteries (kg): 935 Weight (kg): 1944 Power (kW): 7.6 INCLUDED: NEW HAWKER PERFERCT PLUS 36V 640Ah TRACTION BATTERY (8PZS640) NEW NEOS 36V 100A BATTERY CHARGER NEW pre-sweeper side brushes - MIX antistatic bristles NEW pre-sweeper roller brush - MIX antistatic bristles NEW 430mm PPL 0.5 disc brushes (3x) NEW 36V 600W suction turbines (2x) NEW drain hoses (2x) NEW suction hose NEW head guard rubbers (2x) Squeegee blade with new rubbers Tenzi Normal 5 fluid 1000 liters - FREE KEY FEATURES: The 310-liter tank with a durable, flexible divider allows for large amounts of cleaning solution, eliminating the need to frequently stop for refills. The machine's design makes it highly maneuverable. A small turning radius allows for operation even in narrow passages and alleys. The parabolic squeegee beam ensures precise solution extraction from the cleaned surface. The large working width (1230 mm) ensures high surface coverage. The control panel is easy to read and intuitive to use.

Condition: good (used), Year of construction: 2017, functionality: fully functional, X Working range max.: 2000 mm (without repositioning) Y Working range max.: 1250 mm Control: Bosch PNC-P Machine - C-frame - Coordinated guidance - Linear magazine with 15 positions for clamping jaws and tools - Hydraulic clamping jaws (2 pieces) - Drives with maintenance-free three-phase motors - Repositioning device with programmable retaining device - 1st stop pin (right, inside) - Dividing slide Punching head - Electro-hydraulic punching head - Rotatable mono-tool holder - Programmable retaining device position - Tool length compensation - Spray lubrication for punch - Punch slug extraction - Forming function Control - TRUMPF control based on Rexroth IndraMotion MTX - Operating panel with 15" TFT color screen - Integrated technology data - Teleservice interface via the internet - Automatic shutdown - Program management - Production plan Data transfer - USB interface - RJ45 network connection Safety - CE marking - Multi-beam light barriers - Rapid shutdown of drives Extended standard equipment - Ball tables - Chip container - Initial oil filling - Additional clamping jaw - Foot switch for start - Warping detection - Vibration-damped installation Rodpfezv Safex Abpecf - 5 RTC cassettes with die plates

Condition: excellent (used), Year of construction: 2021, GANNOMAT "PROTEC 571" (drilling, grooving, milling) with Clamex and milling tools In top condition Base machine complete in standard configuration for drilling and grooving, including: - Additional safety device via louver curtain - Prerequisite for horizontal Lamello P-system milling - Prerequisite for milling diameters > Ø 16 mm, as well as for the use of multi-part milling tools Detailed technical data can be found in the data sheet for ProTec Type 0571 Machining unit with: PowerBlock with 21 spindles and 1 dado saw - 13 vertical drilling spindles - 6 horizontal drilling spindles in Y / 2 horizontal drilling spindles in X - 1 grooving unit in Y Workpiece sizes and weights - Workpiece width (X): min. 60 mm / max. 1000 mm - Workpiece thickness (Z): min. 6 mm / max. 60 mm - Workpiece length (Y): min. 250 mm in continuous mode max. 5600 mm programmable workpiece length in software - Workpiece weight: max. 75 kg 1 Milling unit Profit HSK63F with 3-way magazine for automatic tool change, motor 5.5 kW (S1), 1000-18000 rpm with frequency inverter, clockwise and counterclockwise rotation, for tool holder HSK63F with collet 462E/OZ25, cutter length up to 130 mm including options 1 Roller table 765 mm (Y-axis) foldable, for the front of the machine, width 500 mm 1 Roller table 765 mm (Y-axis) foldable, for the rear of the machine, width 500 mm 1 Auxiliary stop 600 mm with integrated rollers for roller tables 1 SET OF TOOLS: Drill set for ProTec Rjdezu A D Eepfx Abpjcf 1 Carbide grooving cutter  125/30 mm, grooving cutter width (SB) 4 mm, Z=12, LI, by Leitz 1 Tools for milling unit Profit HSK63F and HSK63F with 3-way magazine with collet 462E up to shank diameter 25mm, HSK and cutter set 1 HSK mounting set 1 Mounting device HSK63F, easiest operation with maximum user comfort thanks to roller clamping system, no clamping or tightening required, mounted on a stable base or workbench, 1 Hook wrench for HSK63F collet 462E, 1 Extraction distributor Ø 160 mm / Ø 80-80-80 mm, pitch 196 mm 1 Counterpressure device from above 1 Tool for vertical Lamello P-system milling Machine in very good condition with many drills and tools included. The machine can be viewed and demonstrated at our showroom. Location: available from stock in 54634 Bitburg - immediately available -

Condition: like new (used), Year of construction: 2021, functionality: fully functional, workpiece length (max.): 4,600 mm, workpiece width (max.): 2,200 mm, workpiece height (max.): 250 mm, Equipment: rotational speed infinitely variable, Holz-Her 5-Axis CNC Nesting Machining Center DYNESTIC 7535 Working area: 4600 x 2200 mm. Vector speed is 128.0 m/min. The milling spindle has a power output of 13.0 kW (S6) and accommodates tools with a maximum diameter of 350 mm via HSK interface. Drilling unit with 24 spindles – 18 vertical and 6 horizontal. The maximum drilling diameter is 35 mm. For grooving, the drilling head is equipped with an integrated saw unit for blades with a maximum diameter of 125 mm and a maximum width of 4 mm. 18-position disc tool changer, pneumatically liftable and covered to protect the HSK 63F holders, as well as a single-position pick-up changer for saw blades up to 350 mm in diameter. Pneumatically retractable stops in the table for special machining either on the nesting table or using vacuum pods. Rjdpjx E Ah Iefx Abpocf Vacuum capacity of 750 m³/h, distributed across 2 pumps with 500 m³/h and 250 m³/h respectively, intelligently controlled by ECO-VAC software. To optimize vacuum efficiency, the table features a 16-zone vacuum system. The pre-installed pusher unit is connected to the extraction system and can be used for panel cleaning and/or clearing the nesting table. Delivery, installation, and machine commissioning training available directly through us at additional cost. The machine is currently located at our shipping warehouse in Gratwein, Austria. In case of discrepancies between the German version and any foreign language version, the German version shall prevail. Our general terms and conditions can be found on our website at holzher.de/de/agb.

Year of construction: 2022, condition: ready for operation (used), controller manufacturer: SIEMENS, table load: 3,000 kg, Automated sheet metal storage system manufactured in 2022. This TRUMPF Automated Sheet Metal Production System features a storage height of 7,900 mm and a maximum load per storage location of 3,000 kg. It includes 266 storage locations and supports sheet formats of 3,050 x 1,525 mm. If you are looking to get high-quality automated storage capabilities, consider the TRUMPF Automated Sheet Metal Production System we have for sale. Contact us for further details. • Storage system: STOPA Compact II • Type: Automated sheet metal storage system with chaotic storage management • Storage height: 7,900 mm • Sheet format: 3,050 x 1,525 mm • Maximum load per storage location: 3,000 kg • Number of storage locations: 266 • Total storage capacity: 798 t • Configuration: 8 sections/towers, up to 37 storage levels per section • Pallet format: GF 3050 x 1525 x 90 mm • Pallet types: SPO, SPMgl • Loading heights: 185 / 275 / 460 mm • Functions: Automatic material storage and retrieval; automatic material supply to connected production cells; storage interface for integrated production machines • Storage control • Server operating system: Windows Server 2022 • Central storage management and automated material flow management • Integration with TRUMPF production equipment • Connected production cells • TRUMPF TruLaser 5030 fiber (L76) • Machine type: CNC 2D fiber laser cutting machine • Working area: 3,000 x 1,500 mm • Laser source: TruDisk 6001, 6,000 W • CNC control: Siemens SINUMERIK 840D sl • TRUMPF TruMatic 6000 fiber • Machine type: Combined CNC punching and fiber laser cutting machine • Working area: 3,050 x 1,550 mm • Laser source: TruDisk 3001, 3,000 W • Maximum punching force: 180 kN • Linear tool magazine: 25 positions • TRUMPF TruBend Center 7030 (B34) – Cell 1 • Machine type: Automatic panel bending center • Max bending length: 3,123 mm • Max thickness: structural steel 3.0 mm; stainless steel 2.2 mm; aluminum 4.0 mm • Max box height: 220 mm • TRUMPF TruBend Center 7030 (B34) – Cell 2 • Same specifications as Cell 1 • System functionality (summary) • Central automated storage and retrieval of raw sheet material • Automatic supply of material to connected laser, punch-laser, and panel bending cells • Automatic transfer between storage and production stations • Centralized, high-capacity sheet handling • Main system configuration • 1 x STOPA Compact II automated sheet storage system • 1 x TRUMPF TruLaser 5030 fiber 2D laser cutting cell • 1 x TRUMPF TruMatic 6000 fiber punching and laser cutting cell • 2 x TRUMPF TruBend Center 7030 automatic panel bending cells Additional equipment Rsdpfxjzu Sugs Abpscf • For TRUMPF TruLaser 5030 fiber (L76) • Automatic pallet changer • LiftMaster Compact 1530 (automatic loading and unloading) • STOPA storage connection/interface • For TRUMPF TruMatic 6000 fiber • SheetMaster 3000 x 1500 mm (automatic sheet handling) • GripMaster 3000 x 1500 mm • Storage system integration/interface • For TRUMPF TruBend Center 7030 (both cells) • 2-axis part manipulator • 5-axis rear stop • Rotary manipulator • ToolMaster Bend • Automatic loading and unloading • Storage interface • System-wide • Central storage management server (Windows Server 2022)

Condition: used, Year of construction: 2018, operating hours: 6,442 h, Technical Data Working Area Axis Travel - X-axis: 4000 mm - Y-axis: 1970 mm - Z-axis: 455 mm Machining Area - X working area: 3000 mm - Y working area: 1550 mm - Z clearance: 250 mm Axis Systems - X-axis: Helical rack and pinion drive - Y-axis: Precision ball screw drive - Z-axis: Precision ball screw drive - Linear guides on all axes - Automatic central lubrication Main Spindle - 5-axis electro spindle - Type: 5-axis spindle with universal joint - Power: 12 kW (S6 operation) - Tool holder: HSK F63 - Maximum speed: 24,000 rpm - Ceramic bearings with air cooling - Full power available at approximately 12,000 rpm - Speed range: 1,000 - 24,000 rpm - Clockwise rotation - Integrated tool changer interface - Liquid-cooled spindle - Electrically controlled extraction hood - Maximum tool weight: 6 kg - Maximum saw blade diameter: 350 mm Tool Changer System 12-position linear tool magazine - Mounted on the left side of the machine frame - Separate station for tool changers - Maximum tool diameter: 250 mm - Maximum tool length: 240 mm 18-position disc tool magazine - Mounted on the gantry - Suitable for drilling tools and tool changers - Maximum tool diameter: 250 mm - Maximum tool length: 280 mm Drilling Aggregated Head DH18 6H 1S drilling head - 12 vertical spindles: 7 spindles in the X direction, 5 spindles in the Y direction - 4 horizontal spindles in the X direction - 2 horizontal spindles in the Y direction - Drilling stroke: 70 mm - Maximum drilling depth: 70 mm - Tool holder: 10 mm - Individual control of the spindles - Integrated slotting saw - Saw blade diameter: 120 mm - Maximum slotting saw blade thickness: 5 mm - Speed up to 7,500 rpm Vacuum and Clamping System Console Table - 6 consoles with front and rear stops - Wireless two-circuit vacuum system - Height of vacuum cups: 100 mm - Pneumatic console locking - Programmable pneumatic stops - 4 adjustable side stops - Reinforced support arms - Load-bearing capacity of the support arms: 40 kg each Vacuum Pump Capacity: - 90 m³/h at 50 Hz - 108 m³/h at 60 Hz - Additional vacuum connection for template machining - Controlled compressed air connections for frame clamps - Separate vacuum and compressed air switching for all consoles WoodFlash Software Package Control Panel - Complete machine operation via the CNC panel - Program creation and editing - Tool and workpiece management - Manual machine commands Rjdpfx Aszuw E Rjbpecf - Monitoring of vacuum, compressed air and safety systems Mobile Control Panel - 24" LED monitor - Keyboard and mouse - USB connection Operator Device for Feed Rate - Manual feed override potentiometer - Variable feed rate adjustment during machining Safety Devices - CE safety system - Safety mats instead of light curtains - Emergency stop system - Protective fence on the left side - Safety monitoring of the doors - Sensors to monitor vacuum and compressed air Optional Equipment - External release switch - Protected energy chain system - Additional locking for A and C axes - Saw blade changing station on the gantry - Operating hours: 6442 hrs.

Condition: used, Year of construction: 2018, CNC-CONTROLLED MACHINING CENTER AUTHOR M 200 AUTHOR M200 3710x1620 Z250 - CNC-controlled machining center 1 Technical data Work area I.M.S. I.U. Work area X-axis 3710 mm * 146" * Work area Y-axis 1620 mm * 63¾" * Workpiece passage Y 1900 mm 74¾" Workpiece passage Z 250 mm 9¾ Workpiece length for pendulum machining 1700 + 1700 mm 67" + 67" Travel speed of the X-Y axes PRO-SPACE 56 m/min 184 ft/min Travel speed of the X-Y axes PRO-SPEED 78 m/min 256 ft/min * Distance covered by all tools in the X and Y direction; see the corresponding layout for further details. With a 5-axis motor, the dimension in Y increases to 1680mm (66"), for motor JQX or 1720mm (67½") for motor KS/KT max. Width of the loadable plate for horizontal drilling, electric spindle only oriented vertically, no central reference stops Installation data I.M.S. I.U. Installed power 23 - 28.5 KVA Electrical standard specifications 400 Voltage 50 Hz 3 phases Air consumption 450 Nl/min Compressed air consumption 4500 m³/h 2650 CFM Extraction air velocity 30 m/sec Extraction nozzle diameter 250 mm 9.8 Inches Noise level VSA * LAV * Drilling 72.2 74.6 Milling 74.3 80.7 Reference standard EN ISO 11202:1995* VSA = unloaded and without extraction * LAV = in operation with extraction Structure of the base body: The CNC machining center can be equipped flexibly with different milling units as well as multi-spindle drilling heads and many other units, up to dowel drilling units. In order to meet all requirements in the field of wood and plastic processing, as well as the demands of the users, each machine can be equipped with 3, 4 or 5 machining axes. The selection of drilling units extends to up to 34 drilling spindles with an integrated groove saw for the back panel groove or rabbet machining. The possibility of using this high-quality CNC machining center both as a cantilever table machine and with an aluminum grid table underscores the flexible range of applications and the performance of the M100 and M200 series. Powerful drilling heads, with individually selectable drilling spindles, max. RPM 8,000, and implemented in . technology, "the most robust drilling spindles on the market", with more than 1,000 maintenance-free application hours (lubrication interval of the drilling spindles). The possibility of being able to replace the drilling spindles within a very short time, "even without a technician", through the technology, without disassembling the drilling gear, sets a benchmark in the industry and is already standard on your machining center. Imagine your CNC machine performing hinge drilling in just one drilling operation (option), instead of the usual 3. An option that underscores our claim to offer you robust and high-performance units on our machines. Ideally and flexibly equipped for a wide variety of requirements. Whether manual or automatic, the FLEX cantilever work table allows vacuum cups and mechanical clamping elements, such as pneumatic clamps for window or curtain wall constructions (option), to be quickly, safely and cost-effectively adjusted to any material and clamping requirements, making your day-to-day work easier. Differently sized vacuum cups and clamping elements, which were developed in close cooperation with customers and users, are available as an option. Redozvhkyopfx Abpjcf

Condition: good (used), Year of construction: 2010, functionality: fully functional, bending force (max.): 230 t, number of axes: 5, Equipment: CE marking, documentation/manual, safety light barrier, Bending length [mm] 3230 Press force [tons] 230 Control system TRUMPF TASC 6000 Standard equipment: Machine - Robust machine frame as a welded construction in all-steel design - Press beam with high bending strength - Spherical bearing of the press beam with press beam inclination - Proportional valve technology and switchable double pump - Modern block hydraulics with control valves mounted on the cylinder - Electronic pressure gauge - Measuring system with centrally mounted glass scales and temperature compensation - Oil cooler - Control cabinet cooling - Modern machine design Back gauge system - Rear back gauge system, 2-axis, with rack and pinion drive for X and R axis - 2 back gauge fingers with secure adjustment from the front Tool clamping - Upper tool clamping system "New Standard Clamping", manual, hardened, self-centering; for vertical tool change - Lower tool holder with hydraulic clamping, hardened Lower tool movement - Lower tool movement programmable (pneumatic, 2 positions) Control - Machine control: TRUMPF TASC 6000, graphical - Workshop programming - Windows XPe, Pentium 4 with 2.8 GHz clock frequency - 2 GB RAM - 15" touch screen - Network-enabled - Teleservice via analog telephone connection Operation - Control panel with LCD keypad, foot switch for up, down and emergency stop - Communication bus for the use of ACB angle sensor tools Safety - Safety device: integrated side doors + Rear back gauge system, 5-axis (X, X1, R, Z1, Z2) + Upper tool clamping, hydraulic + CNC crowning + BendGuard + Additional foot switch Rjdpfjzv Sbiex Abpocf + 2 support consoles + 1 MobileControl + ACB prepared

Year of construction: 2018, condition: used, Screw compressor Manufacturer: Renner Type: RS132D Year of manufacture: 2018 Technical data - Main drive motor: direct drive of the compressor stages via a shaft coupling - Oil filter / thermostat unit: regulates the cooling of the compressor oil and filters it - Oil-injected compressor stage: compressed air generation - Suction regulator: regulates the amount of air drawn in by the compressor - Control cabinet: controls and regulates the compressor system - Suction air filter: filters the air drawn in - Radial fans: generate cooling air for the oil and compressed air coolers - Compressed air outlet: connection point for an external compressed air network - Minimum pressure retaining valve: maintains a minimum system pressure for oil supply, separates network / system pressure - Fine oil separator with oil suction line, sight glasses, and check valve: oil separation via air-oil filter cartridges, return of separated oil from the compressed air - Safety valve: relieves pressure in case of overpressure - Oil filler plug with oil level monitoring: electronic oil level monitoring - Oil drain: drains the oil reservoir - Compressed air / oil combined cooler: cools the compressed air and the compressor oil - Control system: RENNERtronic - Integrated standby heater Rcedpjzu Aibofx Abpef Compressor - Counterclockwise rotation (without gearbox) / Clockwise rotation (with gearbox) Suction regulator The suction regulator is mounted directly on the screw compressor. It regulates the volume flow of air drawn in by the screw compressor through the suction filter. Operating principle of the suction regulator: The suction regulator has only one main valve. This valve operates as a stepless control valve as well as a tightly closing shut-off valve. In full-load operation, the suction cross-section is fully open with minimal pressure drop. In part-load operation, the suction cross-section is automatically regulated by limiting the stroke and adjusted to the actual air requirement. When the system is stopped, this valve quickly and automatically closes the entire suction cross-section completely. The multiple functions of the regulator are initiated by only one control unit. Minimum pressure retaining valve The minimum pressure valve is located at the compressed air inlet of the air aftercooler. It performs two functions: 1) As a pressure retaining valve, it prevents the pressure from dropping below a minimum overpressure of 4.5 bar when there is no back pressure. This pressure is necessary to ensure the oil supply to the compressor. At the same time, this minimum overpressure is required for good oil separation. 2) As a check valve, it prevents the backflow of compressed air from the compressed air network or the pressure vessel into the compressor system. This allows the separator vessel to be completely relieved when the system is shut down. The valve operates automatically. Adjustment of the minimum pressure valve may only be carried out by personnel authorized by the manufacturer! Suction air filter The suction air filter is installed in the housing and connected to the suction regulator via a ventilation hose. The micro-dry filter with a fineness of 10 μm is used to filter the suction air. The filter can be cleaned several times before it needs to be replaced. Use only original replacement filters! Pressure transmitter The pressure transmitter, used in all systems with electronic control (RENNERtronic / -Plus), is connected to the compressed air outlet (network press

Condition: ready for operation (used), Year of construction: 2016, travel distance X-axis: 710 mm, travel distance Y-axis: 750 mm, travel distance Z-axis: 210 mm, spindle speed (max.): 20,000 rpm, number of axes: 3, This 3-axis ISEL FlatCom M30 DoppelFlat 75-35 was manufactured in 2016. It features a complete sound-insulated safety enclosure with sliding viewing doors and a swivel-mounted CNC control console. The machine is equipped with a top-mounted multi-port suction hood and integrated pneumatic pressure regulators. If you are looking to get high-quality milling capabilities, consider the ISEL FlatCom M30 DoppelFlat 75-35 gantry milling machine we have for sale. Contact us for further details. • Machine Type: CNC Gantry Milling (Double Flat / Twin Table Station) • Enclosure: Complete sound-insulated safety enclosure with sliding viewing doors • Control Unit: Swivel-mounted CNC control console with monitor, keyboard, touchpad, status indicator lights, and key switch • Operator Controls: Standalone two-hand safety control pedestal equipped with palm switches and emergency stop button • Extraction System: Top-mounted multi-port suction hoods with 4 flexible extraction hoses • Cooling & Climate Control: Cabinet-mounted enclosure air conditioning/cooling units • Pneumatic System: Integrated pneumatic pressure regulators, air filtration assembly, manifold block, and coiled hose connection • Safety Equipment: Red/Green signal tower light mounted on the frame Rcjdpfx Abszu Rtuepof

Condition: used, Column-guided bandsaw, semi-automatic, METORA - KALTENBACH, type HMB 380 DS for 90° cuts only (Made in Austria) Machine no. 4580028, year of manufacture approx. 1993 Cutting range: round Ø 380 mm Square 380 x 380 mm Saw blade dimensions: 5650 x 34 x 1.1 mm Saw blade speed: 25-108 m/min, infinitely variable Material feed height: 870 mm Hydraulic drive power: 1.5 kW Saw motor drive power: 4 kW Power supply: 400 volts, 50 Hz - Fully hydraulic bandsaw in a two-column design - Hydraulic saw head lowering with infinitely variable cutting pressure adjustment - Lowering speed infinitely adjustable - Hydraulic clamping of the workpiece with hydraulic bundle clamping from above - Hydraulic unit integrated in the machine base - Material feed roller on the feed side with gear motor (not mounted on the machine frame) - Coolant system with coolant pump for water emulsion - Minimum quantity lubrication for the saw blade - Electric heating element for coolant and hydraulics - Length stop, TRENNJAGER type EX-Stop1, with handwheel adjustment, digital display and hydraulic stop carriage clamping Rjdpfx Absdzqtgopscf Stop base length 6750 mm, stop travel 5650 mm, stop arm can be hydraulically folded up without roller conveyor Footprint of the base machine L x W x H: 2800 x 1400 x 2450 mm Machine weight: approx. 3 tons Weight of the stop system: approx. 800 kg in good condition

Year of construction: 2015, condition: ready for operation (used), controller manufacturer: SIEMENS, Robotic Brushing Cabin manufactured in 2015. This M.A.I. ASD 1 features a KUKA 6-axis industrial robot arm and a Siemens SIMATIC Touch Panel for intuitive control. It includes a mobile Ruwac industrial dust extraction system and a central vertical clamping fixture for workpiece positioning. With comprehensive safety features such as a fully enclosed booth and emergency stop controls, this machine ensures a secure working environment. If you are looking to get high-quality brushing capabilities, consider the M.A.I. ASD 1 machine we have for sale. Contact us for further details. Rsdpozu Rwtsfx Abpecf - Description: Robotic Brushing Cabin- Integrated Industrial Robot: KUKA 6-axis industrial robot arm (labeled "04")- Robot Controller: KUKA KRC4- Control Panel: Siemens SIMATIC Touch Panel- Extraction Unit: Mobile Ruwac industrial dust extraction system (Zone 22 ATEX compliant)- Workpiece Fixture: Central vertical clamping and positioning fixture- Safety Features: Fully enclosed protective booth, safety light curtains (Leuze electronic), interlock key switches (Schmersal / Eaton), Emergency Stop control, and Lockout/Tagout (LOTO) station

Condition: used, Year of construction: 1991, Eye-level control panel, Aigner integral stop including feed with sliding carriage (without stop ruler), milling stop with digital display and swivel mechanism Storage location: Nattheim Rcedoyi A Tdopfx Abpof

Condition: used, Year of construction: 2024, Integrated SIAD Industrial Hydrogen Compression System (249 kW) - Manufacturer: SIAD Macchine Impianti (compressor), SAEP & FLOVEX (exchangers), Capelli & Cie (vessels). - Type: Turnkey reciprocating hydrogen compressor skid designed for ATEX Zone 2 hazardous areas. - Applications: Hydrogen gas (H2) boosting for chemical processing, mobility, and energy storage. Technical Specifications Rcedpfx Aboztw Upspof - SIAD HMS4-2 Compressor (2024): 249 kW | 384 kg/h | 0.1 to 3.5 bar(g) | ATEX Zone 2 - IIC - T3. - SAEP Gas Exchanger R-36050 (2024): 248 L volume | 10 bar(g) | -20 to +200 °C. - FLOVEX Oil Cooler (2024): BEM/OTT 403.4-13-2 | ASME VIII Div.1 | 10 bar(g). - Capelli Main Buffer Vessel (2024): 10,250 L | P265GH Carbon Steel | -1 to +0.5 bar(g) | 2,310 kg. - Capelli Condensate Tank (2024): 1,140 L | 316L Stainless Steel (X2CrNiMo17-12-2) | 730 kg. Working Principle & Highlights Low-pressure hydrogen (0.1 bar) is boosted to 3.5 bar(g) at 384 kg/h by the 249 kW SIAD unit. Thermal management is handled by FLOVEX and SAEP exchangers, while the 10,250 L Capelli tank absorbs system pressure surges. - ATEX Compliant: Certified for hazardous Zone 2 gas group IIC environments. - Robust Metallurgy: Built with P265GH steel and 316L stainless steel for H2 service durability. - Modular Skid: Plug-and-play setup combining compression, cooling, and buffer storage.

Condition: used, Year of construction: 2012, - Machining area: 5300x1400 mm - Main spindle replaced 3 years ago - 18-position tool changer Technical data Machining area - In the X direction: 5300 mm - In the Y direction with main spindle + WZ-0: 20 mm: 1400 mm - In the Y direction with drilling unit: (all vertical drills) 890 mm - Single-position machining: X = 2 x 2550 mm - Free space in the center: X = 200 mm - Alternating field machining: X = 2 x 2250 mm - Free space in the center: 800 mm 1 automatic tool/adapter changer magazine - Arrangement: mounted on the support, moving in the X direction - Disc changer with 18 magazine positions Guidance system - All axes are equipped with pre-tensioned, surface-hardened precision roller guides. Rodpezuw Rtsfx Abpocf Central lubrication - Manual central lubrication for all main axis linear guides and Z ball screw. 1 vacuum pump, 90 m3/h Console table consisting of: - 2 work piece stops fixed on the right and 2 on the left in the X direction, for movement in the Y direction - 10 adjustable support arms in the X direction, each with a rear stop - All stops are controlled by the program - The suction plates are fixed via the patented 2-circuit clamping system, eliminating the need for hoses. - 8 smooth support rails, automatically retractable - 2 push buttons for the workpiece clamping/releasing function Additional 2nd vacuum pump, 90 m3/h 1 additional central stop row, for centering workpieces Chip conveyor 1 main spindle - Drive power: 10.0 kW in S-6 operation - 7.5 kW in S-1 operation - Tool holder: HSK F63, taper diameter = 38 mm, similar to DIN 69893 - Speed range: infinitely variable RPM, programmable 1 centrally integrated CNC axis, rotating 360 degrees - for all adapter units, with torque support on the main spindle and pneumatic interface 1 vertical drilling unit l14 with 6 spindles, horizontal and attachment unit for a dado cutter - Horizontal drilling units with 2 outputs each Attachment unit for a dado cutter - Swivel range: 0 or 90° Control system ICOS CNC Modern, powerful PC-based control system with: - User-friendly interface with Windows standards - Trajectory control of all servo axes - Job list / order processing - IMA backup and recovery system on two hard drives - Uninterruptible power supply (UPS) IMAWOP software package - for dialog-oriented creation of CNC machining programs - - 3D view and basic simulation of the programmed workpiece, the suction cups and consoles including tool and adapter display.

Year of construction: 2026, condition: new, ProfiStop Alpha is a simple to use auto measuring stop for high-accuracy medium-heavy timber cutting. Speed up your cutting through the roof, simply, and introduce advanced job-management functions to run your production efficiently. • High-speed automatic servo motor cut measurement • Simple operation and setup, compatible with most saws • Medium duty 20-40 kg recommended material weight • Ideal for steel, framing timber, aluminium • Automated and streamlined jobs management • Label printing and bar-code / QR code jobs input (optional) • Jobbing integration to your ERP system (optional) Available lengths: 1.5 m, 3 m, 4.5 m, 6 m, 7.5 m, 9 m. Highly suitable for: • Frame and truss manufacture • Pallets and boxes manufacture Rcsdpfxolwuk Te Abpef • Furniture manufacture • Planters manufacture • Retail timber sales Can be used with all your existing saws including: • Industrial drop saws • Guarded up-cut saws • Band saws • Radial arm saws • Drills and presses Model: ProfiStop Alpha Length: 3 m Stroke: 2580 mm Pushing capacity: 20 - 40 kg Software: Optimiser Supplied with a roller table or as a linear unit only for installation to your existing tables. Quoted price is excluding the table. QUALITY AUSTRALIAN-MADE MACHINES.

Condition: used, mileage: 32 km, power: 121 kW (164.51 HP), first registration: 01/2026, fuel type: diesel, overall weight: 3,500 kg, color: grey, gearing type: automatic, emission class: euro6, number of seats: 3, total length: 6,704 mm, total width: 2,474 mm, total height: 2,778 mm, loading space length: 4,256 mm, loading space width: 1,784 mm, loading space height: 2,025 mm, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), navigation system, soot filter, Internal number: 4019.CHO25.SC52480 Errors and prior sale excepted! ---- SPECIAL EQUIPMENT * Airbag (passenger side) * Trailer hitch - fixed, 13-pin socket - incl. trailer stability control (TSC) * Bi-Xenon headlights with static cornering light, LED daytime running lights * Fuel tank 95 l * Load compartment floor: vinyl floor covering "Easy Clean" * Sliding door, left * Side wall paneling extending to the roof * Seat package 8A: driver's seat adjustable in 4 ways - passenger's double seat - headrests, height adjustable - driver's seat & passenger's seat (outer seat), individually and variably heated - tray on the passenger's double seat (foldable) - interior armrest for driver - lumbar support for driver - seat cover: fabric - leather steering wheel, heated * Technology package 6P: exterior mirrors elect. adjustable, heated and foldable - Blind Spot Information System incl. Cross Traffic Alert - audio system - fog lights - LED downlight - Pre-Collision Assist, camera and radar-based - rear emergency braking assist - lane keeping assist incl. lane departure warning - traffic sign recognition system, extended - Park Pilot System front/rear - speed control system, adaptive with Stop & Go function - all-round camera - navigation OTHER EQUIPMENT * 1 battery * Airbag driver side * ABS with electronic brake force distribution - ESP with traction control - hill start assist - crosswind assist - safety brake assist - rollover protection - emergency brake assist incl. hazard warning lights * Exterior mirrors, short arm - with integrated turn signals * Battery: battery life, programming of the battery life to 10 min * On-board computer with consumption and mileage information (e.g. remaining range) as well as outside temperature display and Ford ECO-Mode * Headliner in driver's cab * Double-wing rear door with 256° opening angle, (without window) without rear window, with locking magnet * Rev counter * Power windows - with quick-up/-down function for driver's side * Parking brake electronic * Ford Easy Fuel - comfort fuel filler cap and misfueling protection * FordPass Connect - incl. live traffic information and WLAN hotspot 5G modem (up to 5G/LTE, for up to 10 mobile devices) * Heated windshield * Glove box with lockable lid * Interior lighting with delay function with reading lamps in the front * Automatic climate control - with automatic temperature control * Load compartment lighting * Steering column, adjustable in height and reach * Emergency Assist eCall emergency call system * Particulate filter: diesel particulate filter Rcsdpfx Asxvgczsbpef * Radio accessories: 12-inch multi-function display and Ford SYNC 4 communication and entertainment system with voice control as well as Bluetooth and USB interface - integration of various telephony functions and hands-free system with control via voice command - integration of storage media - emergency call assist - Ford Power-Up software updates - support of Android Auto and Apple CarPlay, AppLink (wireless) - capacitive touchscreen technology - 15 different languages * Wheels: wheel covers - full surface * Wheels: tire repair set * Wheels: steel wheels 6.5 J x 16 with 235/65 R 16 tires * Windscreen wipers with rain sensor * Sliding door, right * Mud flaps rear * Side protection strips * Power steering * Seat belts - seat belt tensioners and force limiters front - warning system for unfastened driver's seat belt * Start-stop system * Rear bumper, with integrated step * Partition (plastic) at the height of

Condition: used, mileage: 32 km, power: 121 kW (164.51 HP), first registration: 01/2026, fuel type: diesel, overall weight: 3,500 kg, color: black, gearing type: automatic, emission class: euro6, number of seats: 3, total length: 6,704 mm, total width: 2,474 mm, total height: 2,778 mm, loading space length: 4,256 mm, loading space width: 1,784 mm, loading space height: 2,025 mm, Equipment: ABS, air conditioning, central locking, electronic stability program (ESP), navigation system, soot filter, Internal Number: 4008.CHO25.SC49175 Errors and omissions excepted! ---- SPECIAL EQUIPMENT * Airbag (passenger side) * Trailer hitch - fixed, 13-pin socket - incl. trailer stabilization (TSC) * Bi-Xenon headlights with static cornering lights, LED daytime running lights * Fuel tank 95 l * Load compartment floor: vinyl flooring "Easy Clean" * Sliding door, left * Side wall paneling, high up to the roof * Seat Package 8A: driver's seat, 4-way adjustable - passenger's double seat - headrests, height-adjustable - driver's seat & passenger's seat (outer seat), individually and variably heated - tray on the passenger's double seat (foldable) - interior armrest driver - lumbar support driver - seat upholstery: fabric - leather steering wheel, heated * Technology Package 6P: exterior mirrors, elect. adjustable, heated and foldable - blind spot assist incl. cross traffic alert - audio system - fog lights - LED downlight - Pre-Collision Assist, camera and radar-based - rear collision warning - lane keeping assist incl. lane departure warning - traffic sign recognition system, extended - park pilot system front/rear - speed control system, adaptive with Stop & Go function - all-round camera - navigation FURTHER EQUIPMENT * 1 battery * Airbag driver side * ABS with electronic brake-force distribution - ESP with traction control - hill start assist - side wind assist - safety brake assist - rollover protection - emergency brake assist incl. emergency brake light * Exterior mirrors, short arm - with integrated turn signals * Battery: battery runtime, programming of the battery runtime to 10 min * On-board computer with consumption and mileage information (e.g. remaining range) as well as outside temperature display and Ford ECO-Mode * Headliner in driver's cab * Double-wing rear door with 256° opening angle, (without window) without rear window, with holding magnets * Rev counter * Electric windows - with quickdown/up function for driver's side * Parking brake, electronic * Ford Easy Fuel - comfort fuel filler cap and misfueling protection * FordPass Connect - incl. live traffic information and WLAN hotspot 5G modem (up to 5G/LTE, for up to 10 mobile devices) * Windshield, heated * Glove compartment with lockable lid * Interior lighting with delay function with reading lights in front * Automatic climate control - with automatic temperature control * Load compartment lighting * Steering column, adjustable in height and reach * Emergency call assistant eCall emergency call system * Particulate filter: diesel particulate filter * Radio accessories: 12 inch multifunction display and Ford SYNC 4 communication and entertainment system with voice control as well as Bluetooth and USB interface - integration of various telephony functions and hands-free system with control via voice command - integration of storage media - emergency call assistant - Ford Power-Up software updates - support for Android Auto and Apple CarPlay, AppLink (wireless) - capacitive touchscreen technology - 15 different languages * Wheels: wheel covers - full area * Wheels: tire repair kit * Wheels: steel wheels 6.5 J x 16 with 235/65 R 16 tires * Windshield wipers with rain sensor * Sliding door, right Rjdpfx Absxvgchjpscf * Mud flaps rear * Side protection strips * Power steering * Seat belts - seat belt pretensioners and belt force limiters in front - warning system for unfastened driver's seat belt * Start-stop system * Rear bumper, with integrated step * Partition (plastic) at the height of the

Condition: used, mileage: 2,45,280 km, power: 130 kW (176.75 HP), first registration: 07/2018, fuel type: diesel, empty load weight: 2,097 kg, maximum load weight: 1,403 kg, overall weight: 3,500 kg, wheelbase: 3,640 mm, next inspection (TÜV): 05/2028, fuel: diesel, energy efficiency: C, fuel consumption (urban): 8 l/100km, fuel consumption (extra-urban): 7.4 l/100km, fuel consumption (combined): 7.6 l/100km, color: white, driver cabin: other, gearing type: automatic, emission class: euro6, suspension: other, number of seats: 3, loading space volume: 11 m³, loading space length: 3,450 mm, loading space width: 1,780 mm, loading space height: 1,950 mm, Equipment: ABS, air conditioning, airbag, central locking, cruise control, electronic stability program (ESP), immobilizer system, onboard computer, sliding door, soot filter, traction control, * Very well-maintained German vehicle, second owner * Vehicle IDNT No.: WV1ZZZSYZJ9044772 * Valid MOT until: Technical Data: * Overall length 5986mm * Overall width 2040mm * Overall height 2590mm * Wheelbase 3640mm * Permissible total weight 3500KG * Unladen weight 2097KG * Payload 1403KG * Trailer load 3000KG Cargo area: * Length 3450mm * Width 1780mm * Height 1950mm Special Equipment: * Storage Package 2 * Airbag driver/front passenger side, front passenger airbag can be deactivated * Audio system Composition Media (radio/CD player, MP3 playback function) * Exterior mirrors electrically adjustable and heated * Flooring in the cargo area: wood * Driving Assistance Package 2 * Driving assistance system: Parking assistance front and rear with active side protection * Remote key (2) foldable * Air conditioning Climatic (cab) * Rear view camera * Seats in the cab: Driver's seat comfort Standard Equipment: * Anti-lock braking system (ABS) * Drive type: Front-wheel drive * Exterior mirror, convex, left * Exterior mirror, convex, right * LED turn signals integrated into exterior mirror * Flooring in the cab: Rubber * On-board tools * Underbody panel with Cd value * Dual headlights * Two-tone horn * Entry handle on rear pillar, left * Entry handle on rear pillar, right * Electronic Stability Program (ESP) * Driving assistance system: Hill-start assistant * Driving assistance system: Brake assistant (HBA) * Driving assistance system: Side wind assistant * Power windows, front * Windshield laminated glass * Transmission automatic - (8-speed) * Grab handles A-pillars * Rear wing doors without glazing * Interior lights in the cab: LED * Interior lights in the cargo/passenger compartment: LED * Body/structure: Box high-roof * Body variant: High roof in vehicle color * Fuel tank: 75 liters * Radiator grille with chrome strip on top * Cargo area partition, high, without window * Steering column (steering wheel) adjustable * Headlight range control * Truck registration * Engine 2.0 liter - 130 kW TDI * Rear fog light * Wheelbase 3640 mm * Tire repair kit * Diesel particulate filter * Low emissions according to emission standard Euro 6 * Sliding door cargo/passenger compartment, right * SCR system (AdBlue technology) * Power steering, electro-mechanical * Seat cover / upholstery: Fabric * Seats in the cab: Front passenger seat adjustable * Start/stop system engine * Sockets (12V connection) in the cab (2 pieces) * Front bumper in gray with trim in vehicle color * Daytime running lights * Lashing eyes in cargo area * Seat belt warning system (driver's side) * Immobilizer (electronic) * Heat-insulating glazing * Central locking with remote control and interior operation * Permissible total weight 3.50 t Nationwide delivery possible!!! Trade-in possible!!! Leasing and financing also possible without down payment Errors, printing errors and prior sale are subject to change Rcjdpfjy Umn Rsx Abpof

Condition: new, Year of construction: 2023, Stable cast iron construction Milling spindle can be swiveled backwards from 0° to -45° Right-left rotation of the milling spindle Generously dimensioned milling unit made of cast iron, attached directly to the table Solid and precise cast iron table Standard curved milling protection hood Aluminum sliding carriage ball contact system Torsion-resistant, highly precise, smooth-running and problem-free in daily use 10-year SCM guarantee on wear of the guideways Milling spindle mounted high up with precision ball bearings, resulting in the lowest possible bearing load and the longest possible service life Exact router fence with quick adjustment and fine adjustment with a scale on the stop jaw Integrated suction connection Large milling table opening allows the use of larger tools Weight approx. 290 kg Extraction connection diameter 2 x 120 mm Working table L x W = 1000 x 435 mm Table height 900 mm Rodpfxeiknp Rj Abpscf Sliding carriage length 1000 mm Sliding carriage width 270 mm Drive motor power 5.0 kW, 400 V, 50 Hz Milling spindle inclination 0 to -45 ° Spindle usable length 100 mm Overhang max. above table 130 mm Spindle speeds 3500/7000/10000 rpm Mandrel diameter 30 mm Tool diameter max. lowerable 180 mm

Year of construction: 2026, condition: new, ProfiStop Alpha is a simple to use auto measuring stop for high-accuracy medium-heavy timber cutting. Speed up your cutting through the roof, simply, and introduce advanced job-management functions to run your production efficiently. • High-speed automatic servo motor cut measurement • Simple operation and setup, compatible with most saws • Medium duty 20-40 kg recommended material weight • Ideal for steel, framing timber, aluminium • Automated and streamlined jobs management • Label printing and bar-code / QR code jobs input (optional) • Jobbing integration to your ERP system (optional) Available lengths: 1.5 m, 3 m, 4.5 m, 6 m, 7.5 m, 9 m. Rodef Dqhaopfx Abpjcf Highly suitable for: • Frame and truss manufacture • Pallets and boxes manufacture • Furniture manufacture • Planters manufacture • Retail timber sales Can be used with all your existing saws including: • Industrial drop saws • Guarded up-cut saws • Band saws • Radial arm saws • Drills and presses Model: ProfiStop Alpha Length: 4.5m Stroke: 4080 mm Pushing capacity: 20 - 40 kg Software: Basic Supplied with a roller table or as a linear unit only for installation to your existing tables. Quoted price is excluding the table. QUALITY AUSTRALIAN-MADE MACHINES.