Used Metal Material for sale (47,891)

Condition: used, Pay-off and take-up decoiler for coil material WANZKE CAMU Type SC 515/M Serial no. 8487 Year of manufacture: 2006 Coil weight approx. 1,500 kg Maximum coil width: 600 mm Coil inner diameter: 370 - 640 mm Maximum coil outer diameter: 1,800 mm Mandrel shaft diameter: 90 mm Distance from mandrel crown center to mandrel base: 950 mm Mandrel crown speed: 13 rpm Motor speed: 920 rpm Codpfowvv Rqjx Ab Sjhc Gearbox transmission ratio: 1:70 Mandrel drive motor power: 1.1 kW Power supply: 400 Volt, 50 Hz - Mechanical expansion of the mandrel crown with hand crank - Drive via geared motor with worm gearbox, directly mounted on the mandrel shaft - Geared motor with electric brake - Mandrel shaft with mechanical slip clutch, pre-tensioned and adjustable via disc springs - Mandrel crown without strip travel arms - Without electrical control system and without loop switch Space requirement (L x W x H): 1300 x 800 x 1230 mm Weight: 380 kg Good condition

Condition: used, Strip Processing Line, Decoiler and Straightening Machine Year of manufacture: 1991 Strip width: 50 to 450 mm Sheet thickness with straightener inactive: 6 mm Sheet thickness with straightener active: 2 mm - Very well equipped with feed-in aids Required floor space for the entire line (L x W): approx. 7000 x 3000 mm Total weight: approx. 11 tons Good condition Straightening Machine HMS Type RS 47-04/1, Machine No. Strip width, nominal: 400 mm Strip width, max. pass-through: max. 455 mm Strip thickness at 400 mm width: max. 1.5 mm (steel) Chodpfx Abjif Sg So Soc Strip thickness at 400 mm width: max. 2 mm (copper) Speed: max. 40 m/min Number of straightening rolls: 7 Straightening roll diameter: Ø 40 mm Number of pinch rolls: 2 Pinch roll diameter: Ø 80 mm Entry height/pass-through height: 1500 mm - Straightening rolls hardened, ground and hard-chromed, with central support - Pinch rolls hardened, ground and hard-chromed, with hydraulic lifting - Manual straightening roll adjustment - Feed assist with hydraulically extendable tongue and hydraulically adjustable deflection pulley - Adjustable side strip guides - All straightening rolls driven via distribution gearbox and cardan shafts - Both pinch rolls driven via gearbox with cardan shafts - Frequency-controlled drive via geared motors - Straightener opening stroke 250 mm for cleaning or for processing thicker material, lifting by trapezoidal-thread spindle - Ultrasonic loop control Transport dimensions (L x W x H): 3600 x 2200 x 2200 mm Net weight: approx. 4 tons Decoiler HMS Type BA 1.5-06/80, Machine No. Coil weight: max. 8000 kg Outer coil diameter: max. 1600 mm (with load carriage) Outer coil diameter: max. 2000 mm (without load carriage) Diameter of coil turntable: Ø 1700 mm Coil inner diameter, expansion range: 460–520 mm Coil width, nominal: max. 630 mm Expansion jaw width: 750 mm Height of decoiler drum above base plate: 1500 mm - Decoiler drum driven by hydraulic motor and gear - Pneumatic overrun brake on the decoiler drum (TWINFLEX) - Hydraulic expansion of the decoiler drum, centrally via wedge slider system - Hydraulic pressure arm with hydraulically driven double pendulum roller - Coil loading carriage with 12-ton lifting capacity and 300 mm stroke - Decoiler on elevated travel frame with motorized cross travel drive Transport dimensions (L x W x H): 3500 x 1900 x 2500 mm Net weight: approx. 5 tons Central Hydraulic Power Unit (adjacent) Tank capacity: 350 liters Drive power: 18.5 kW - Drive motor with 2x REXROTH tandem pumps - Oil cooler as air heat exchanger with fan motor Transport dimensions (L x W x H): 1600 x 850 x 1450 mm Net weight: approx. 800 kg Electrical Cabinet (adjacent) - All cable connections via Harting connectors Transport dimensions (L x W x H): 2800 x 500 x 2250 mm Net weight: approx. 800 kg

Condition: ready for operation (used), functionality: fully functional, power: 7.5 kW (10.20 HP), 6 rotor knives 2 stator knives Chsdpfxjxfzaas Ab Sjc Grinding chamber 500 x 250 mm Power 7.5 kW

Condition: good (used), functionality: fully functional, power: 10 kW (13.60 HP), 6 rotor knives 2 stator knives Grinding chamber 500 x 250 mm Chjdpexfy Tlsfx Ab Ssc Power 10 kW

Condition: used, Revolving briquetting press RUF type RBK 55/2500/120 S Hydraulic pellet press or briquetting press for grinding sludge, metal chips, or similar No. 70002 Year of construction 2009 Briquette diameter 120 mm Briquette length in the pre-compactor approx. 120 mm Pressing force in the pre-compactor 30 tons at 260 bar Briquette length in the main compactor approx. 80 mm Pressing force of the main press cylinder 250 tons at 260 bar Stroke size of the main press cylinder 120 mm Pressing force of the counter-press cylinder 250 tons at 260 bar Stroke size of the counterpress cylinder 15 mm Piston diameter of the main press cylinder 350 mm Csdpfx Ajhg Uz Ieb Sohc Press stroke Cycle time approx. 30 sec. for grinding sludge with low residual oil content Hopper size of the screw conveyor 1000 x 600 mm Hydraulic motor power 37 kW Mains connection 400 Volt, 50 Hz, 45 kW - Revolver with 5 stations for high material throughput - Pre-compressor stage for pressing material into the turret disk - 2 opposing main press cylinders with 120 mm and 15 mm stroke - Ejection cylinder for ejecting the finished briquettes from the turret disk - Infinitely variable adjustment of the hydraulic speed for each pressing stage - was used for grinding sludge from metal processing - Material hopper as hopper with screw conveyor - the machine was completely overhauled at RUF in 2018 - a new SIEMENS Simatic touch panel was installed in 2020 - only a few operating hours after the overhaul very good condition Grinding sludge recycling - great savings through cooling lubricant recovery - Large savings in disposal costs due to the reduction in volume and weight of the grinding sludge - Grinding sludge briquettes with a low residual oil content can possibly be classified as "non-hazardous waste".

Condition: new, Year of construction: 2025, turning diameter over cross slide: 250 mm, turning length: 730 mm, turning diameter: 500 mm, spindle speed (max.): 1,800 rpm, CNC lathe machine CK 6150 with flat bed We offer a new CNC lathe machine model CK6150. We use this machine in our production and you can see it in operation before ordering. The CK 6150 lathe has a flat bed and hardening guides, which ensures a long period of operation of the equipment. The machine is equipped with a CNC system, the GSK CNC system is installed as standard. Optionally, the machine can be equipped with a Fanuc or Siemens CNC system. The machine can have a tool holder for 4-6 or 8 tools, depending on the customer's wishes. It is possible to install a hydraulic chuck on the machine, which will greatly simplify the process of installing parts on it and a hydraulic tailstock. The CK 6150 lathe can be equipped with additional supporting frame for more accurate manufacturing of long parts. Technical specifications: Model CK 6150 x 1000 Maximum workpiece diameter over bed 500 mm Maximum workpiece diameter over support 250 mm Maximum workpiece length 1000 mm Maximum turning length 730 mm Spindle bore diameter 82 mm Spindle speed 150-1800 rpm Engine power 7.5 kW Mechanical chuck (hydraulic optional) Chuck size 250 mm. 4-position tool holder (6 or 8 optional) Maximum tool size for tool holder 25x25 mm Machine weight 2700 kg Chjdpfxoxdmgvj Ab Sec Machine dimensions 2650×1700×1820 mm We can also supply lathes CK 6140, CK 6150 and CK 6160 with other dimensions of the working part: CK 6140 dimensions of the working part 550/750 mm CK 6150 dimensions of the working part 1000/1500/2000 mm CK 6160 dimensions of the working part 1000/1500/2000 mm CK 6152E dimensions of the working part 1000/1500/2000/3000 mm CK 6165E dimensions of the working part 1000/1500/2000/3000 mm CK 6165E dimensions of the working part 1000/1500/2000/3000 mm CK 6185E dimensions of the working part 1000/1500/2000/3000/4000 mm CK 61100E dimensions of the working part 1000/1500/2000/3000 mm CK 61125E dimensions of the working part 1000/1500/2000/3000 mm

Year of construction: 2018, condition: ready for operation (used), Control Unit Brand MITSUBISHI Model GOT2000 Additional Equipment Full optimization of 30 dimensions in two quality grades Cutting programs for different customers Cutting at marks made with fluorescent chalk Trimming of margins (beginning and end of the input material) Cutting in bundles (several pieces at once) Counters for meters, total, shifts, operator, monthly Cutting accuracy ±0.2 mm This METAL TECHNIKA OWD-1600 was manufactured in 2018. It features a GOT3000 Mitsubishi controller and excels in full optimization of 30 dimensions across two quality grades. It supports various cutting programs and can handle input material widths from 12 to 250 mm and heights up to 120 mm. Central oil lubrication ensures smooth operation. Consider the opportunity to buy this METAL TECHNIKA OWD-1600 Optimizing Cross-Cut Saw. Contact us for more information about this machine. Chedow Uaigopfx Ab Sec Application Types Sawing (Wood)

Condition: new, We offer here for sale a new workbench from the manufacturer Metal Sistem. Delivery time: approx. 3 - 4 weeks Technical data of the workbench: Manufacturer: Metal Sistem Type: Super 4/5/6 Workbench width: 1.200 mm Workbench depth: 900 mm Workbench height: 900 mm Included in delivery: 02x workbench stand, new Material color: compl. galvanized type of stand: TS4 incl. cross and diagonal braces, foot plates The stands are pre-assembled (bolted truss) 723 mm high 700 mm deep Cedpfxjhq Txhe Ab Sohc 04x workbench trusses, new Crosshead type: TS profile dim.: 70 x 42 x 3 mm clear width: 920 mm Material color: compl. galvanized 01x worktop, new Wood type: MDF thickness: 28 mm dimension: 900 x 1.200 mm Material color: black 03x steel shelves, new dimension: 300 x 700 mm Type: H29/D 02x swivel castors, new 02x brake/steering rollers, new 01x angle set, new for mounting the worktop 08x safety hook, new Material color: compl. galvanized

Year of construction: 2025, condition: new, functionality: fully functional, cutting width (max.): 1,500 mm, spindle speed (max.): 700 rpm, spindle speed (min.): 60 rpm, warranty duration: 12 months, Equipment: rotational speed infinitely variable, TGM-1250 Expanded Metal Mesh Machine Expanded Sheet Press is suitable for both plate production and integrated production with Roll tape. Expanded Metal Press is preferred for the best performance electronic products. Expanded Metal Machine is operated with 1 operator control. Materials that our Expanded Metal Machines can process; DKP, HRP, Aluminum, Stainless etc. By entering the quantity and stroke values you want to produce on the control screen, your production will be provided automatically. Without cutting your expanded metal products, you can make hollow production by entering the desired gap dimensions between PLC control screen. Our machines are speed controlled, adjusted according to the material to be processed and the mold. The expanded sheet machine is automatically lubricated by the oil tank as all moving machine elements. (All moving elements of the expanded sheet machine are automatically lubricated with the help of the oil tank) Our Expanded Metal Machines; Suitable for filter wire production, culvert wire production, suspended ceiling mesh production, aluminum facade mesh etc. You can contact us for Expanded Metal Machine For Sale, Expanded Sheet Press For Sale, Baklava Sliced Perforated Press For Sale. THRA - 1250 - DECOILER (HYDROLIC) Acts with sensors connected to the expanded sheet metal press or other machines. In accordance with demand, internal clamping system can be produced mechanically and hydraulically. V type hydraulic loading trolley can also be integrated into the machine. Chsdewihwpspfx Ab Soc We manufacture in 500, 1000, 1250, 1500 mm and different capacities. You can contact us for Roll Forming Machines for Sale, Roll Forming Machines for Sale. TGE-1250 - Expanded Metal Flattener Machine Expanded Sheet Flattening Flattening Machine is suitable for both plate production and integrated production with Expanded Sheet Press. The expanded metal flattening ironing machine can be precisely adjusted on both sides. All of our Flattening-ironing machines are made of special solid steel material and special heat treatments are applied. Irons the thickness of the expanded metal to the raw material thickness of the sheet. Materials that our Expanded Metal Flattening Machines can process; DKP, HRP, Aluminum, Stainless etc. You can contact us for Expanded Metal Flattening Machine for Sale, Expanded Sheet Metal Flattening Machine for Sale and Perforation Flattening Press for Sale with Baklava Slices. It does not damage and wear the roll bands. We also provide custom designs by offering engineering solutions in line with customer demand. TGD - 1250 - Expanded Metal Leveler and Straightening Machine Expanded Sheet Leveller and Straightening Machine is suitable for both plate production and integrated production with Expanded Sheet Press. The expanded metal Leveller and Straightening machine can be precisely adjusted on both sides. All of our crushing-ironing machines are made of special solid steel material and special heat treatments are applied. Irons the thickness of the expanded metal to the raw material thickness of the sheet. Materials that our Expanded Metal Crushing Machines can process; DKP, HRP, Aluminum, Stainless etc.

Condition: ready for operation (used), Year of construction: 2017, functionality: fully functional, Metal Technika OWD 1600 Optimizer - manufactured in Poland - year of production 2017 TECHNICAL PARAMETERS: - cutting width 250 mm - cutting height 120 mm Chodpfsrx Rxpox Ab Sec - Capacity from 3 200 to 8 150 mb /8 h - sorting table with 5 knockouts - Electronics Controller with color touch screen display "MITSHUBISHI" - Features - full optimization of 30 dimensions in two quality classes, - creation of cutting programs for different customers, - cutting at the point of marking with fluorescent crayon, - margin cutting (beginning and end of the input material) - cutting in packages (several elements at once) - meters, total, shift, operator, monthly counters, - cutting accuracy ±0.2 mm - Motor 5.5 KW (saw Ø500 - 140z) - Width of input mat 12 - 250 mm max. width / height ( 250 / 50 mm) - Height of input mat 12 - 120 mm max. h/w ( 120 / 130 mm) - Input mat length up to 4,200 mm - Lubrication Oil central lubrication system - Automation at the output Connection for slant conveyor and sorting table

Condition: used, Rain gutter, downpipe and elbow forming machines, complete line. Three machines. 1. Rain gutter forming machine, strip cutting with band saw. Produced gutter diameter: 80 x 100 mm Used sheet metal dimensions: Width: 350 mm. Thickness: 0.43 – 0.55 mm. 2. Downpipe forming machine, can form 127 mm and 152 mm (standard) sizes. Cutting with guillotine. Used sheet metal dimensions: Width: 300 mm. Csdpfxev Evcts Ab Sshc Thickness: 0.43 – 0.55 mm. 3. Elbow forming machine: 400V/3 If you have any further questions, we will be happy to answer them.

Condition: new, Year of construction: 2024, operating hours: 1 h, functionality: fully functional, table length: 3,000 mm, It is primarily designed for use in recycling of waste cables (used to separate copper or aluminium particles from plastic ones), but because of its unique design it is also applicable for the separation of different particles (eg. the electronic waste, the recycling of automobiles and industrial radiators, the recycling of batteries, catalysts, or for the separation of any two particles of different specific gravity). Cedeuzyfhspfx Ab Sjhc A new version with double beds enables high throughput of material with very high purity of the obtained fractions (copper) and copper loss is reduced to zero. The machine is equally efficient in the separation of the granules obtained by grinding of solid cable and granules of so called hair wire. Unlike the dry separator, here in plastic there are no copper particles. Several companies bought it just to screen the plastic they got by recycling of cables with dry separator and thus additionally extracted copper from the plastic (up to 10%). There are standard three sizes that can recycle 350-1000 kg of ground mass per hour, but on request there can be larger performances (the machine code is also the size of table). The machine is extremely quiet and peaceful and is not it necessary to additionally be fixed on the ground (foundation). One can easily be built on your existing recycling line or we can offer you the cable granulator, and conveyor belt for material supplying from granulator to separator or from the separator.

Condition: excellent (used), Desktop Metal 3D Printer Complete System Here we offer you Desktop Metal 3D printer complete system. Desktop Metal 3D printer studio system Complete system: 3D printer + debinding machine + sintering furnace Desktop Metal The three-part solution includes 3D printer, debinder and furnace Manufacturer Desktop Metal Model Desktop Metal Studio System Operating condition Used (Good) Year of manufacture 2019 Desktop Metal Studio System Includes: 1.1 Desktop Metal Studio 3D Printer Bound Metal Deposition (BMD) Technology. Features: Printed materials metal Technology FDM Use Industry Other features Office X-stroke 30 cm (12 in) Y-stroke 20 cm (8 in) Z-stroke 20 cm (8 in) Description: Unlike laser-based systems that selectively melt metal powders, the printer extrudes bonded metal rods - similar to an FDM printer. This eliminates the safety requirements often associated with metal 3D printing, and it enables new features such as the use of closed-cell fills for lightweight strengths. 1.2 Desktop Metal Studio debinder (delamination machine) fully automatic debinding Cleaning tank: 17.4 L (in process) / 22.5 L (stock) Description: The debinder prepares green parts for sintering by dissolving the primary binder. With a low emission design, it requires no external ventilation and is safe for an office environment. Cjdpfx Ajk Hz Nqeb Sjhc Automatic liquid distillation and recycling means no need to refill between cycles. 1.3 Desktop Metal Studio Sintering Furnace hybrid technology (microwaves & conventional heating elements) Installation space 305x205x205mm Carbon housing Gas supply: 2 x 900 L gas cylinders Heating power: 20 kW Features: Function Sinter Configuration Chamber Heat source gas Other features High temperature, automatic Maximum temperature 1,400 °C (2,552 °F) Description: Fully automated and sized to fit through an office door, the furnace delivers industrial-grade sintering in an office-friendly package. Built-in temperature profiles matched to each design and material provide uniform heating and cooling without the residual stresses associated with laser-based systems. Condition: used / used Scope of delivery: (see picture) (Changes and errors in the technical data, specifications are reserved!) Further questions we can answer on the phone for you.

Condition: new, We offer here for sale a new workbench from the manufacturer Metal Sistem. Delivery time: approx. 3 - 4 weeks Technical data of the workbench: Manufacturer: Metal Sistem Type: Super 4/5/6 Workbench width: 1.200 mm Workbench depth: 900 mm Workbench height: 900 mm Included in delivery: 02x workbench stand, new Material color: compl. galvanized type of stand: TS4 incl. cross and diagonal braces, foot plates The stands are pre-assembled (bolted truss) 888 mm high 700 mm deep 04x workbench trusses, new Crosshead type: TS profile dim.: 70 x 42 x 3 mm clear width: 920 mm Material color: compl. galvanized Chjdpfx Ajhq Twyeb Sec 01x worktop, new Wood type: MDF thickness: 28 mm dimension: 900 x 1.200 mm Material color: black 03x steel shelves, new dimension: 300 x 700 mm Type: H29/D 01x Angle set, new for fixing the worktop 08x safety hook, new Material color: compl. galvanized

Condition: as good as new (ex-display), Fronius TPS 4000 CMT ✅ Scope of delivery: ➤Fronius TPS 4000 CMT power source ➤Fronius FK 4000 ➤Fronius VR 7000 CMT wire feeder ➤Fronius Robacta CMT hose package or CMT hand hose package ➤Fronius intermediate hose package ~1.5m ➤Fronius RCU 5000i ➤Fronius Interbus Rugged Line interface ➤Ground cable 3-4m ➤Pressure regulator from Messer (new) The prices listed start at ... euros. Prices/offers are customized based on the device configuration. CMT (Cold Metal Transfer) technology is particularly known for its high precision and flexibility when welding thin materials and delicate components. Unlike traditional MIG/MAG welding processes, CMT uses a controlled, pulsating wire feed, which transfers the welding wire very precisely into the weld pool. This minimizes spatter, enables excellent heat input control, and reduces distortion and discoloration of the material. We always have several machines in stock in different versions. Ask for a personalized configuration / additional options. ---- AVAILABLE FOR IMMEDIATE DELIVERY PROPER INVOICE A viewing is possible in Vienna, Austria! ✔ Insured shipping on a pallet is no problem! ✔ ✅Questions✅Questions✅ Questions: ✅Questions✅Questions✅ Questions✅ Cjdpfx Abswbixrj Sehc ►►►What is the condition of the machines? ►►► To explain, we buy like-new used devices, disassemble them, inspect everything, replace any worn parts if necessary, and only then, after successful test welding, is the device released for sale. "All" devices are clean and have neither burn holes in the displays nor countless burn holes or dents scattered throughout the device! You're buying an item from us that's ⭐worth seeing and doesn't look completely finished! ►►►Do we receive an invoice when you purchase from us? Yes, you receive a proper invoice from us. If you have a valid VAT ID, we can issue a net invoice if the requirements for intra-community delivery within the EU are met. ►►►What payment options are available? Prepayment or cash upon personal pickup ►►►Is insured shipping possible? Yes, we will be happy to send you the purchased set, well packaged and insured, on a Euro pallet. ►►► ►►►Is there a warranty? We sell the machines at one-third the original price and unfortunately don't have the flexibility to offer a warranty. You are welcome to test the devices on-site and pay in cash. ►►►Why buy from us? We are experts in this Fronius welding machine series and always have 60-80 devices in stock – exclusively Fronius, no other manufacturers! We are experts in these devices and don't sell anything we don't know about.

Condition: new, functionality: fully functional, Year of construction: 2025, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, nozzle changer, safety light barrier, High-strength welding bed Partitioned smoke extraction system Fully automatic butter injection system Fully automatic cutting, material saving, fast speed Cutting area 4000 × 2000 mm X‑axis travel 1520 mm Y‑axis travel 4020 mm Z‑axis travel 80 mm Csdpjw A Iiljfx Ab Sohc Max. combined positioning speed 170 m/min Acceleration 2.8 G Machine dimensions (L×W×H) 9500 × 2900 × 2380 mm Footprint 10500 × 3400 mm Net weight 8500 kg

Condition: good (used), Year of construction: 2020, Complete set worked only 2 years New price EUR 500.000   Set with: 3d printer Furnace oven Crosslink Oven Inverter and paxcking table Worked with fillament BASF 17.4 stainless steel   Build rate 800 cc/Hr 1600 Dpi Up to 800 Dpi with 10pL print head Up to 400 Dpi with 30 pL print head Layer thickness 30 to 200 Micron X - Travel: 400mm Y - Travel: 250mm Z - Travel: 250mm Chodpfx Abowrcuue Sec Plastic printer:Yes Metal printer: Yes Resolution: 200 Accurate: 800 Length: 2500mm Width: 1800mm Height: 2310mm Weight: 2000kg

Condition: good (used), Year of construction: 2020, operating hours: 50 h, functionality: fully functional, Desktop DMA series Dynamic mechanical analyzers DMA25 and DMA50 are "desktop" dynamic mechanical analyzers that offer a high force range and excellent flexibility. From glass transition determination to immersion testing, they are powerful and very cost-effective thermomechanical testing platforms. Applications of the Metravib Desktop series Dynamic mechanical analyzers DMA25 and DMA50 for a wide range of applications - DMA and TMA tests - Determination of glass and secondary transitions - Static and quasi-static tests: Creep, stress relaxation, tensile, compression, etc. - Particularly suitable for the characterization of polymers and composites Codpfx Aborxfy Us Sehc - Tests on materials immersed in a liquid - Analysis of material moisture dependence - R&D / quality control / training / laboratory work

Condition: new, We offer here for sale a new workbench from the manufacturer Metal Sistem. Delivery time: approx. 3 - 4 weeks Technical data of the workbench: Manufacturer: Metal Sistem Type: Super 4/5/6 Workbench width: 1.200 mm Workbench depth: 900 mm Chjdpfx Abehq Txws Sjc Workbench height: 900 mm Included in delivery: 02x workbench stand, new Material color: compl. galvanized type of stand: TS4 incl. cross and diagonal braces, foot plates The stands are pre-assembled (bolted truss) 723 mm high 700 mm deep 02x workbench trusses, new Crosshead type: TS profile dim.: 70 x 42 x 3 mm clear width: 920 mm Material color: compl. galvanized 01x worktop, new Wood type: MDF thickness: 28 mm dimension: 900 x 1.200 mm Material color: black 02x swivel castors, new 02x brake / swivel castors, new 01x angle set, new for mounting the worktop 04x safety hook, new Material color: compl. galvanized

Condition: new, functionality: fully functional, Year of construction: 2025, laser type: fiber laser, Equipment: CE marking, centralized greasing system, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, nozzle changer, safety light barrier, Laser power: 3KW, 6KW, 12KW Standard hardware: waste car, fully automatic butter injection, dual-control workbench, adaptive multi-angle site placement, beam light curtain Optional hardware: fire bricks, high-pressure proportional valve (standard for 6KW and above), safety door lock, Independent laser cabinet, rear exchange table light curtain, rear lifting light barrier, Chsdowz Ukyepfx Ab Soc Rear camera, internal camera, monitoring display, radiation-proof glass, upper cover fan, upper cover, partition dust removal

Condition: good (used), Year of construction: 2020, operating hours: 20 h, functionality: fully functional, The advantages of DMA+300, DMA+1000 and DMA+2000 DMA and TMA testing Precise measurement of viscoelastic properties Determination of glass and secondary transitions Chsdpfx Aborxf Rts Sjc Static and quasi-static tests: Creep, stress relaxation, tension, compression... Fatigue testing of material and industrial component samples (with controlled waveform) Crack growth testing Analysis of solid, pasty and liquid materials: elastomers, plastics, composites, biomaterials, etc. Particularly suitable for the characterization of polymers and composites (polymerized materials, polymerization process tracking, simultaneous DMA/calorimetry, fatigue) Particularly suitable for testing and characterizing elastomers (Mullins effect, Payne effect, frequency sweep, heat build-up, crack growth testing, etc.) Analysis of material moisture dependency Comparison and classification of complex materials for construction R&D / quality control / training / laboratory work DMA+ series with high power Solutions for material characterization The devices in the DMA+ series are dynamic testing machines based on an innovative concept of a one-piece test frame with high rigidity. They are dedicated to accurately analyzing the viscoelastic properties of the most advanced materials. The DMA+ one-piece high stiffness test frame has been designed to offer the widest stiffness and frequency analysis ranges as well as best-in-class ergonomics. The Dyna+ software enables a variety of DMA tests to track the dependence of the material's viscoelastic properties on many parameters. With the optional fatigue module of the Dyna+ software, the testing capabilities can be extended to advanced fatigue tests, heat build-up tests or crack growth tests.

Condition: new, We offer here for sale a new workbench from the manufacturer Metal Sistem. Delivery time: approx. 3 - 4 weeks Technical data of the workbench: Manufacturer: Metal Sistem Type: Super 4/5/6 Workbench width: 1.200 mm Workbench depth: 900 mm Workbench height: 900 mm Included in delivery: 02x workbench stand, new Material color: compl. galvanized type of stand: TS4 incl. cross and diagonal braces, Codpfxjhq Tqdj Ab Sehc foot plates The stands are pre-assembled (bolted truss) 888 mm high 700 mm deep 02x workbench trusses, new Crosshead type: TS profile dim.: 70 x 42 x 3 mm clear width: 920 mm Material color: compl. galvanized 01x worktop, new Wood type: MDF thickness: 28 mm dimension: 900 x 1.200 mm Material color: black 01x angle set, new for fixing the worktop 04x safety hook, new Material color: compl. galvanized

Condition: new, Year of construction: 2025, functionality: fully functional, coil outer diameter: 1,500 mm, coil inner diameter: 508 mm, material thickness: 200 mm, feed length X-axis: 1,520 mm, feed length Y-axis: 3,020 mm, feed length Z-axis: 80 mm, warranty duration: 24 months, total height: 2,380 mm, total length: 8,900 mm, total width: 2,300 mm, load capacity: 1,300 kg, input frequency: 50 Hz, input voltage: 380 V, overall weight: 180 kg, repeat accuracy: 0.02 mm, workpiece weight (max.): 15,000 kg, Equipment: cooling unit, GS-J Series has various workbench sizes such as 3015, 4015, 4020, 6015 to meet different processing needs Suitable for batch processing of thin plates with high flatness requirements of 0.6-3.0mm Uncoiling machine parameters: Maximum weight of coil (kg): 15000 Coil width (mm): 200～1524 Coil outer diameter (mm): Φ800～Φ1500 Coil inner diameter (mm): Φ508mm~Φ610mm (cast iron pad) Coil thickness: (mm) 0.6-2.0mm (stainless steel) ≤1524mm 0.8-3.0mm (carbon steel) ≤1524mm Feeding length (mm): 0～ Maximum stroke of equipment Unwinding speed (m/min): 0～15 Moving speed (mm/s): 0-8 Lifting speed (mm/s): 3.0 Lifting stroke (mm) : 350 Codpsv Awgujfx Ab Sehc Leveling flatness (mm/㎡): ≤±3 Fixed feeding line height (mm) : 870 Sizing accuracy (mm/m) : Length direction ≤±0.2 Diagonal direction : ≤±0.8 Revolutionize Your Coil Processing with One Machine, Five Functions! Uncoiling, leveling, feeding, cutting, and blanking – all in one seamless automated system for maximum efficiency. Smart, Flexible & Versatile - Effortlessly cuts special-shaped workpieces, adapting to diverse production needs - Optional touchscreen control with top-tier international cutting systems - High-quality drag chain cables – durable, bend-resistant, and interference-free

Condition: good (used), Technical data for pallet rack beam: Racking system: Metall Sistem Type: Unipal Codpexb Tp Eofx Ab Sshc Scope of delivery includes: 01x pallet rack beam, used Material color: yellow Box profile: 140 x 45 mm Clear width: 1,800 mm Your contacts in our company: Mr. Andre Evering Mr. Mario Klöver Mr. Falk Deutsch General information about the item: This item is offered for collection only. Any additional transport or shipment of this item will incur extra costs, which can be quoted separately depending on the place of delivery or scope of delivery.

Condition: new, functionality: fully functional, Year of construction: 2025, laser power: 30,000 W, travel distance X-axis: 3,050 mm, travel distance Y-axis: 13,050 mm, travel distance Z-axis: 450 mm, repeat accuracy: 0.02 mm, workpiece weight (max.): 20,000 kg, input frequency: 50 Hz, total length: 16,800 mm, total width: 2,200 mm, total height: 5,120 mm, warranty duration: 24 months, positioning accuracy: 0.03 mm, working range: 13,000 mm, Equipment: cooling unit, safety light barrier, GS-L Series, Glorystar Single Table Gantry Type Metal Laser Cutting Machine Laser Power: 12000-8000W The GS-L Series is a high-power metal laser cutting machine with a gantry-type segmented bed design. It can be freely customized to meet processing format requirements according to customer needs. Key Features: ● Super Large Processing Format with a gantry-style segmented design. ● The GS-L Series has the largest Z-axis travel and height in its class in the industry. Supports extreme thickness cutting for plates over 20mm. Capable of cutting ultra-thick plates up to 70mm. ● High Negative Pressure Automatic Partition Dust Removal ● Equipped with a high-air-volume fan for effective dust removal. Technical parameters: Working area (mm): 13000mm*3000mm（bevel cut: 12500mm*2500mm） X axis travel distance (mm): 3050mm Y axis travel distance (mm): 13050mm Z axis travel distance (mm): 450mm X/Y axis positioning accuracy: ≤0.03mm/m X/Y axis repeat positioning accuracy: ≤±0.02mm Max. synthetic positioning speed: 110m/min Max. acceleration: 1.2G Chjdovmwn Hepfx Ab Sjc Min. setting unit: 0.001mm Floor size (mm): 18500mm*6500mm Main body dimension (mm): 16800mm*5120mm*2200mm Worktable max. weight capacity (T): 20 tons (even load bearing)