Used Spindle Press for sale (24,169)

Condition: new, Year of construction: 2026, Actually one showroom machine available. Very robust machine with high pressing force - is also suitable for producing a salable briquette quality * depending on the material. The large press cylinder and the 80 mm briquette make this possible. Our best-selling briquetting press series + Tried and tested, simple technology, for extremely low susceptibility to errors + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Top price-performance ratio Surcharge for cooling unit + € 4.995 net, (can also be retrofitted later) * cools the pressing tongs (important from 3.5 hours) and the hydraulic oil * Cooling device recommended for regular use of more than 3.5 hours at a time. Briquette diameter: 80 mm Front bush: 125 mm Briquette stroke max .: 100 mm Briquette lift opt ​​.: 80 mm Output (depending on material): up to 200 kg / h * * depending on the bulk weight * based on a bulk weight of 200 kg per cubic meter Motor power: 9.2 kW 400 volts / 50 Hz / 3 phases Length: 2095 mm Width: 1300 mm Height: 1700 mm Weight: 1250 kg Oil volume: 220 liters Silo diameter: 1200 mm Silo content: approx. 1 qbm Pump: 75 liters Hydraulic pre-compressor Cooling pressing tongs option: yes, with special accessory coolable pressing tongs Hydraulic oil cooling option: yes Bledpfjxfwdsx Af Ajn Cooling of the pressing tongs and the hydraulic oil with cooling device (special accessory) Level monitoring option: yes Strand briquette option; yes (depending on material) Option of enlarged filling slide: yes, with special accessory enlarged filling slide CE compliant . Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 18% - Chip length maximum 20 mm - Installation temperature: temperature-controlled room at at least + 5 ° C - The loading must be free of metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear

Condition: used, Year of construction: 2015, functionality: fully functional, operating hours: 170 h, pressing force: 320 t, working width: 5,100 mm, degree of automation: automatic, Equipment: emergency stop, finger protection, foot remote control, lower tooling, safety light barrier, upper tooling, TOSKAR press brake Pressure 320 tons Blodswq Aa Iopfx Af Aen Bending length 5100mm Bending length between columns 4100mm Speed of approach movement 100 mm/s Speed of bending movement 9 mm/s Speed of return movement 100 mm/s Opening 300 mm Distance to columns 500mm Year 2015 Only 170 working hours 5 Axes Y1, Y2, X, R, deflection arrow CNC controller with NexT touch screen

Condition: ready for operation (used), HSM V-Press 860 baler, year 2008–2009, price: €5,800 Pressing force: 54 kN Specific pressing force: 63.46 N/cm² Drive power: 7.5 kW Cycle time: 25 s Loading height: 1,110 mm Feed opening width x height: 1,195 x 650 mm Bale dimensions (L x W x H): 1,200 x 780 x 1,200 mm Bale weight: 480 kg Machine dimensions (W x D x H): 1,797 x 1,247 x 2,985 mm Machine weight: 2,008 kg Binding material: wire Materials processed: foil, mixed paper, cardboard, die-cut waste, textiles, Big Bags, polystyrene HSM V-Press 860 plus, year 2013–2015, price: €8,000 HSM V-Press 860 L, year 2015, price: €9,000 HSM V-Press 860 plus, year 2019, price: €9,000 HSM V-Press 860 plus, year 2024, price: €10,000 HSM V-Press 860, new/ex-demo, year 2020, price: €13,000 4-fold bale wire tying Bale dimensions (L x W x H, mm): 1,200 x 800 x 1,000–1,200 Bale weight: approx. 500 kg Technical data (L x W x H, mm): 1,213 x 1,824 x 2,987 Feed opening (mm): 1,200 x 565 Cycle (s): 35 Pressing force (t): 54 Power supply (V): 400 (three-phase) HSM V-Press 860 plus B, year 2020, price: €14,000 Pressing force: 594 kN Voltage/Frequency: 400 V/50 Hz Drive power: 4 kW Feed opening width x height: 1,500 x 651 mm Bale dimensions (L x W x H): 1,500 x 780 x 1,200 mm Bale weight: 550 kg Feeding type: Manual Machine dimensions (W x D x H): 2,099 x 1,245 x 2,985 mm Machine weight: 2,336 kg Binding material: wire Material processed: foil, cardboard Idle cycle time: 25 s Bljdpfx Afera Rbgo Asn

Condition: like new (used), Spindle support bearing Manufacturer: Union Blodpedvvtlofx Af Aen Overhang: 600 mm Spindle diameter: 130 mm

Condition: ready for operation (used), Year of construction: 1983, functionality: fully functional, machine/vehicle number: 681852N, total length: 2,200 mm, total width: 1,450 mm, total height: 1,550 mm, Size: 360 x 520 mm Availability: in stock Total impressions: 49.7 million Bjdpfx Ajz D Ernjf Aeln Estimated model year: 1983 Status: discontinued in 2025 Maximum sheet size: 360 x 520 mm Minimum sheet size: 105 x 180 mm Maximum speed: 8,000 sheets/hour Printing units: 2 Total weight: 2,850 kg Includes: 2 x Varn Kompac III, automatic, continuous dampening system Eltek elektrostat P22

Condition: good (used), Year of construction: 2015, functionality: fully functional, bending force (max.): 230 t, number of axes: 5, Bending length [mm] 3230 Press force [tons] 230 Control system TRUMPF TASC 6000 Standard equipment: Machine - Robust machine frame in all-steel construction - Press beam, stress-relieved by annealing - Spherical mounting of the press beam with inclination - Electro-hydraulic upper drive with 4-cylinder technology - Generous bending clearance - Flat front covers - Modern block hydraulics - Electronic pressure gauge - Measuring system with glass scale and spring compensation - Hydraulic oil in the machine (lifetime lubrication) - Oil cooler - Control cabinet cooling via air-to-air heat exchanger Bsdpfx Asz D Tnwsf Aeln - Modern machine design Back gauge system - Rear back gauge system, 2 axes, X and R axes - 2 back gauge fingers with secure adjustment from the front Tool clamping - Upper tool holder, manual clamping, hardened - Lower tool holder, hydraulic clamping, hardened - Lower tool displacement, 2 positions, pneumatic Crowning - Manual crowning Control system - TRUMPF TASC 6000 - Graphical workshop programming - Windows XPe (embedded), Pentium 4 with 2.8 GHz clock frequency - 2 GB RAM - 15-inch touch screen - Network capable - Teleservice via modem Operation - Control panel with LCD keypad and foot switch - Communication bus Safety - Standard safety devices

Condition: used, Universal temperature control unit REGLOPLAS Type 90M/10/SG75/D K/RT50 Pressurized water temperature control unit with electric heating and connections for external cooling Blsdpfx Aoz Au Hbef Ajn Circulating process temperature control for industrial applications in plastics processing, especially for the temperature control of injection molds and other process tools. Manufacturer's serial number: 102010170001, Year of manufacture: 2009 Temperature: max. 90°C (for water) Heat transfer medium: Water Temperature range: +20°C to 90°C Operating overpressure: max. 6 bar Pump capacity: 100 l/min Tank volume: 2.8 liters (internal filling volume) Heating capacity: 10 kW Cooling capacity of heat exchanger: up to 160 kW (depending on the external cooling unit) Pump motor power: 1.5 kW Continuous sound pressure level

Condition: used, functionality: fully functional, Comafer Dinamic 250N briquetting machine with closed-loop oil cooling and cooler capacity: 100–250 kg/hour, depending on the material. Briquette diameter: 75 mm. cylindrical housing (ø1200) with inspection door, additional ring (sleeve) ø1200 / h930, pressing force approx. 1100 kg/cm2. 2 cylinders. briquette cylinder ø 200 mm. pump motor (11 kW / 15 HP, 380 V, 50 Hz). Monobloc, self-centering, without fixing rods for the round die. Electrical control panel with PLC, automatic and manual cycle. Shut-down mechanism with open die and die pressure gauge. Bledpoz D A Ugefx Af Aen Digital thermostat for oil temperature control, level switch to prevent oil leakage. Closed-loop oil cooling system (air/oil). Closed-loop cooler for die cooling (580 mm x 550 mm x 908, weight 56 kg). threading head for the production of long briquettes, briquettes with uniform length, complies with CE standards dimensions: 2100 mm x 1350 mm x 1540 mm (height), weight: 1600 kg

Condition: like new (used), Year of construction: 2021, Almost New: Complete Compaction System Ludden & Mennekes SVS11+KEV 1. Stationary Screw Compactor L&M SVS 11 Bodpfjz Eg Dzsx Af Asln Virtually unused, stationary screw compactor (~1 month) designed for filling compaction containers and/or other containers. The machine is constructed from a robust, welded steel frame with continuously welded seams. Its low-maintenance screw compaction system is suitable for continuous feeding, and the compaction chamber does not require periodic cleaning. Main technical specifications Overall length: 2,480 mm Overall width: 1,660 mm Overall weight: 2,300 kg* Loading height: 1,350 mm Feed opening: 1,375 × 1,490 mm Screw diameter: 750 / 500 mm Screw speed: 17 rpm Drive power: 11 kW Residual-current device / Fused plug Type B / 300 mA 2. Hydraulic Container Coupling/Decoupling System Hydraulically operated coupling and decoupling system with forward and reverse movement. The hooking grippers are operated manually. Designed for the secure connection of different types of compaction containers. 3. L&M KEV Cardboard Intake/Deflection and Pre-Shredding Unit Virtually unused L&M KEV coarse shredding unit for bulky cardboard packaging, cardboard tubes with cores, and other large-format packaging materials. The material is reduced to a size suitable for efficient compaction, helping to improve compactor utilization and reduce disposal costs. The unit can be installed above L&M self-compacting containers or stationary compaction systems so that shredded material falls directly into the filling opening. Main technical specifications Dimensions (L × W): 1,230 × 1,490 mm Shredding shaft width: 1,400 mm Cutting knife diameter: 585 mm Number of cutting knives: 9 Feed opening: 960 × 1,400 mm Drive power incl. power supply: 2.2 kW + 0.75 kW 4. L&M PCS 6500 Compaction Container Main technical specifications Capacity: 32 m³ Dimensions: 6,500 × 2,500 × 2,600 mm PRICE ON REQUEST

Condition: used, Year of construction: 2005, power: 7 kW (9.52 HP), FOR SALE / FOR RENT: VERTICAL BALER! (Rental available in Lithuania, Latvia, Estonia, and Poland) Technical Information: Manufacturer: HSM Model: HSM 500 VL Pressing force: 54–540 kN Bale size: 1200 x 800 x 1200 mm Bale weight: approx. 500 kg Max. bale size: approx. 1200 x 800 x 1200 mm (W x D x H) Press chamber dimensions: 1200 x 800 x 1520 mm (W x D x H) Motor: 7.5 kW Blodpfez Ehgwox Af Aon Year of manufacture: 2005 SALE PRICE - 4400 EUR + VAT RENTAL PRICE - 160 EUR + VAT

Condition: excellent (used), Year of construction: 1989, functionality: fully functional, Equipment: documentation/manual, Man Roland 202 TOB Series 249 Size: 520 x 740 mm 2 colors Very good working condition Man Roland 202 TOB Series 249 Size: 520 x 740 mm 2 colors Very good working condition 4 grippers Bedpfxjzzk E Rj Af Aeln Weko RCI console

Condition: like new (used), Year of construction: 2020, operating hours: 5,600 h, functionality: fully functional, machine/vehicle number: 0-250-77-3262, 1. BASIC MACHINE - rigid steel frame construction - 2 workpiece clamping devices with integrated stop system - Separate adjustment of the clamping devices via rack and pinion gear in X-direction - Digital AC servomotors - The position of the clamping devices at the workpiece is program-controlled - Adjustment of the clamping devices between the separate processing steps in the processing area is possible. - Automatic measuring of the workpiece thickness and lengths by the clamps and the stop system - Blowing nozzle for safe removal of residual parts off the clamps 1.1 LOWER PROCESSING SUPPORT - Rigid aluminium cast construction - Integrated threefold divided table with selectable air cushion - Lateral stop system - Adjustment of the axes in Y- and Z-direction - Ball bearing spindle (Z-direction) and rack and pinion gear (Y-direction) - Digital AC servomotors - Suitable for fitting of various configurations 1.2 UPPER PROCESSING SUPPORT - Rigid aluminium cast construction - Integrated threefold divided pressure beam with selectable air cushion - Adjustment of the axes in Y- and Z-direction - Ball bearing spindle (Z-direction) and rack and pinion gear (Y-direction) - Digital AC servomotors - Suitable for fitting of various configurations 1.3 WORKPIECE DIMENSIONS workpiece length: min. 200 mm workpiece length: max. 2500 mm workpiece width: min. 70 mm workpiece width: max. 1000 mm - with restrictions in processing: 1300 mm workpiece thickness: min. 8 mm (2 x 4 mm) workpiece thickness: max. 80 mm (2 x 40mm) Bsdsz Df Txepfx Af Aeln workpiece stacking: max. 2 pieces - same workpiece dimensions Note: - Workpieces must have a straight edge at the reference edge - Max. curve tolerance: +/- 0.5 mm for a work- piece length = 2000 mm - The workpiece length/width ratio should be >=1. The longer edge of the workpiece should be placed on the machine. - Warped workpieces (>= 0.3 mm) lead to a higher rate of processing tolerances and wear at the workpiece tables - Due to the chips no stackable workpieces can be guaranteed for router processings. - An external cleaning or extraction in the outfeed area is recommended. - For through holes of double parts the drilling quality depends on the workpiece material and the tool as well as on the feeding speed profile and the rotation speed of the drilling spindle. Thus, however, efficiency could possibly be reduced. 1.4 WORKPIECE FEEDING AREA - Air cushion table in rigid frame construction - Surface from Hornit board - integrated fan 1.5 WORKPIECE REMOVAL AREA - Cross belt conveyor in rigid frame construction - 8 transport belts, frequency-controlled drive - 8 electro-pneumatic controlled disengaging device 2. CE SAFETY AND PROTECTION DEVICES - Safety fences in the lateral and rear area - Safety mats in the feeding area 3. ENVIRONMENTAL CONDITIONS - prescribed environmental temperature: + 5 degrees up to + 40° C (in case of environmental temperature >35°C or air humidity >65% a cooling unit for switch cabinet is recommended) 4. ENERGY SAVING MODE - ecoPlus button for starting stand-by operation. The button can be activated during processing. This will have the following impacts after the end of the program: - Primary power of drives will be switched

Condition: refurbished (used), Automatic line for forging / hot stamping Installed after refurbishing in 2015 and having run for not more than 1,000 hours, condition is excellent. ➢ ADIGE CM 500 AUTOMATIC SAW ➢ 50 KW INDUCTION OVEN ➢ ELECTRONIC AUTOMATION SYSTEM ➢ VACCARI SCREW PRESS 180 screw diameter ➢ 10-POINT AUTOMATIC LUBRICATION SYSTEM ➢ BALCONI 50T TRIMMING PRESS ADIGE CM 500 AUTOMATIC SAWING MACHINE WITH 3.5-METER AUTOMATIC BAR LOADER Technical specifications: -Min./max. cutting capacity: 8 mm / 60 mm diameter -Standard cutting speed: ADIGE SALA. -Head motor power: (50 Hz) 2.2 kW -End-of-bar scrap equal to or shorter than the usable piece -Central hydraulic tank capacity: 200 liters -Cutting emulsion tank capacity: 50 liters -Weight: approx. 1,200 kg -Siemens electrical components 50 kW INDUCTION OVEN WITH 1 INDUCTOR (8–20 mm) with ELECTRONIC LOADING ARM For horizontal and vertical loading of work pieces Features a brushless motor, programmable axes, and press interpolation with electric axes; electronic components: Siemens Load capacity: 4 kg; vertical stroke: 80 mm; power supply: Electro-pneumatic VACCARI SCREW PRESS 180 screw diameter Technical specifications: -Screw diameter: 180 mm -Theoretical pressure: 300 tons -Table dimensions: 430 x 550 mm -Slide dimensions: 500 x 650 mm -Ram stroke: 350 mm -Distance between uprights below the guides: 450 mm -Distance between uprights within the guides: 350 mm -Max. height between table and ram: 650 mm -Strokes per minute: 35 -Table height under the guides: 300 mm -Main motor: hp 30 -Machine dimensions: 4100 x 2600 x 2200 mm -Approximate weight: 11,000 kg Blodpozcdluefx Af Ajn NEW SIEMENS S7 ELECTRICAL SYSTEM NEW PNEUMATIC SYSTEM NEW LUBRICATION SYSTEM BALCONI 50T TRIMMING PRESS Technical specifications: -Power: 50 tons -Table dimensions: 800 x 500 mm -Ram dimensions: 440 x 380 mm -Max. die height: 400 mm -Adjustable stroke: 100 mm -Strokes per minute: 35–100 -Main motor power: 5.5 kW

Condition: ready for operation (used), Year of construction: 1998, functionality: fully functional, overall weight: 12,000 kg, Used toggle-type cold forming press Bodpfx Afsz E Dc Io Ajln Manufacturer: SCHMID Type: T400 Year of manufacture: 1997 Machine with standard accessories.

Condition: used, Display Model What's Included: - Carrying case Bjdszk Ntrspfx Af Aoln - Unit - User manual - Bit This item is an unused display model Availability: Available shortly Location: Röllbach

Condition: excellent (used), Year of construction: 2005, machine/vehicle number: 102940, WEINIG HYDROMAT H23 ELECTRONIC FEED FREQUENCY CONTROLLED (8 – 100 M/MIN). FEED MOTOR 22 KW 50MM SPINDLES WORKING WIDTH MAX. 230 MM WORKING HEIGHT MAX. 160 MM SHORT INFEED WITH 220MM TOP FEED ROLLERS BOTTOM 15KW 6,000 RPM, OUTBOARD BEARING, JOINTER READY RIGHT 11KW 6,000 RPM JOINTER READY LEFT 15KW 8,000 RPM JOINTER READY RIGHT 11KW 8,000 RPM JOINTER READY LEFT 15KW 8,000 RPM, JOINTER READY TOP 18.5KW 6,000 RPM OUTBOARD BEARING, JOINTER READY BOTTOM 11 KW 6,000 RPM OUTBOARD BEARING, JOINTER READY (STRAIGHT JOINTER) + OUTBOARD BEARING TOP 18.5KW 8,000 RPM OUTBOARD BEARING, JOINTER READY (STRAIGHT JOINTER) + OUTBOARD BEARING BOTTOM 22 KW 6,000 RPM OUTBOARD BEARING, JOINTER READY 12X TOP FEED ROLLERS (2X 220MM + 10X 140MM) 7X BOTTOM FEED ROLLERS POSSIBLE TO ADD ADDITIONAL STRAIGHT / PROFILE JOINTERS AS NEEDED AUTOMATIC LUBRICATION SYSTEM FULL DOCUMENTATION INCLUDED MACHINE LENGTH 5.2M Blodpfx Aez Ezn Uof Asn

Condition: new, Year of construction: 2026, neu 2026 070225 Oktober 2026, Zwiswchenve Türkei 33700 € 643.67 € 30 to 2 mm 400 mm 600 mm Bledpfx Ajwirbxsf Asn 150 mm 1 - 60 mm 140 1/min 4 60 mm 40 mm 200 mm 300 mm 3 kW 1300 mm 1150 mm 2050 mm 1670 kg Welded steel frame construction 4-fold ram guide Pneumatic clutch-brake combination Protective enclosure with light barriers and side doors Mechanical overload protection Two-hand and foot pedal operation Manual stroke adjustment Manual ram adjustment Variable stroke rate via frequency converter Operating modes: * Adjustment mode * Two-hand release * Foot release * 2-stroke operation via light barriers * Continuous operation Touchscreen for * Stroke counter with preselection for continuous operation * Stroke rate adjustment * Lubrication intervals and duration * Alarm messages * Motor direction of rotation * Monitoring of inputs and outputs 2 free cams for connecting peripherals Automatic central lubrication Equipment in accordance with CE regulations Options: vibrations pads € 132,- bolster plate € 720,-

Condition: new, neu ca. 14 - 16 Wochen ab Auf Türkei 74300 € 1404.27 € 100 to 4.5 mm Blodpfx Afjwiqq Se Asn 700 mm 1000 mm 210 mm 1 - 132 mm 58 1/min 6 90 mm 60 mm 300 mm 445 mm 7.5 kW 1650 mm 1545 mm 3011 mm 7000 kg Welded steel construction body frame Crankshaft made of AISI 4140 (42CrMo4) alloy steel, CNC grinded for max. precision SnBz-12 quality bronze to bearings, grinded for min surface resistance Ram supported from 8 sides Pneumatic counter-balancing of the ram 7" touchscreen Gears in oil bath Pneumatic clutch-brake combination PLC control for safety Photocell light barriers Motorized slide adjustable Hydraulic overload protection Two hand and foot pedal control Adjustable stroke (inverter) automatic centrallubrication Machine and equipment in conformity with CE-regulations OPTIONS: vibration pads € 192,00 bolster plate € 2.580,00

Condition: like new (used), Year of construction: 1984, functionality: fully functional, pressing force: 50 t, stroke length: 54 mm, total length: 1,750 mm, total width: 1,400 mm, total height: 3,000 mm, overall weight: 7,500 kg, year of last overhaul: 2022, DGUV certified until: 12/2027, ram adjustment: 80 mm, KAISER V50W high-speed stamping press, year 1984, extensively mechanically and electrically overhauled and modernized in 2022. The machine is in very good working condition and ready for operation. Technical data: Press force: 500 kN / 50 t Table size: approx. 800 × 550 mm Stroke: 54 mm Ram adjustment: 80 mm Speed: up to 400 strokes/min Main motor: SEW-EURODRIVE, 59 kW Year of manufacture: 1984 Bedpfx Afoz D Dq No Aoln Retrofit / modernization: 2022 Equipment / modernization: New electrical equipment Siemens SIMATIC PLC control Siemens SIMATIC HMI touch panel New 59 kW SEW-EURODRIVE main motor SEW drive/inverter PILZ safety system UNIDOR LVCpro press-force monitoring system Two UNIDOR piezoelectric force sensors on the connecting rods Separate monitoring of left/right and total press force on the HMI New electrical cabinet and modern safety components

Condition: good (used), Strautmann AutoLoadBaler baling press Bjdev Aktnopfx Af Aoln Suitable for baling: Cardboard Film PET bottles Foam Cans Electronic waste Machine dimensions (length / width / height) mm: 2047 / 2179 / 3050 Opening approx. 1192 mm / 575 mm Bale size (length / width / height) mm: 1200 / 800 / 1100 Bale weight approx. 480 kg Pressing force kN: 530 Year of manufacture: 2017-2018

Condition: ready for operation (used), Year of construction: 2010, functionality: fully functional, power: 37 kW (50.31 HP), input voltage: 380 V, input current: 80 A, input frequency: 50 Hz, pressing force: 220 t, stroke length: 200 mm, operating speed: 21 mm/s, reverse speed: 200 mm/s, table width: 120 mm, table length: 4,270 mm, table height: 900 mm, throat depth: 400 mm, ram plate length: 4,270 mm, distance table to ram: 400 mm, clearance between the columns: 3,820 mm, oil tank capacity: 350 l, total length: 5,370 mm, total width: 2,160 mm, total height: 3,275 mm, overall weight: 16,950 kg, Equipment: CE marking, documentation/manual, safety light barrier, Hydraulic press brake LVD EASYFORM-10 220/4270 Touch-B Year of manufacture: 2010 Serial number: 33189 Technical specifications Force: 2200kN Working length: 4270mm Distance between uprights: 3820mm Stroke: 200mm Distance table – ram: 400mm Gap: 400mm Turbo: PP5400 Approach speed: 120mm/s Working speed: 21mm/s Return speed: 200mm/s Weight: 16950 kg Motor: 37kW Oil capacity: 350 COMMAND CONTROL TOUCH-B • Table PP8170 V-axis • EFL 90/130 • Top tool clamping PP3090 – Wila • Back gauge X600 X’ R Z1 Z2 PP8096 • Safety: CE PP3580 – laser-safe • PP1115 manual front support: 2pcs • T-axis Heavy duty 200kg Bljdpfxoz Eqwlo Af Asn

Condition: excellent (used), Manufacturer: Indramat spindle motor with Emag spindle Type: 1MB 310 D-6DB-A094A1/SO20 Rotor: 1MR 310 D-A094/SO20 Stator: 1MS 310 D-6B-A1/SO20 Pn 19 kW P kb 27 kW n N 700 rpm n max 6000 rpm Condition: Used, fully functional 2 units available in stock. Bledpfev U Ag Dex Af Aen

Condition: used, Year of construction: 2006, working width: 520 mm, roll width: 520 mm, roll diameter: 1,000 mm, Equipment: documentation/manual, Video below We offer this used ETI Converting Equipment Cohesio ST 520 coater, die cutter, UV silicone coating, flexographic printing press 1 colour, , 11 magnetic cilinders, year of construction 2006. multifunctional equipment that allows self-adhesive materials and labels. linerless 1 flexo 2 hotmelt coating guns (roatating bar, lips + ‘Waterwall”) 3 unwinders Web width of 520 mm E + L webguides at the infeed and between hotmelt and UV printing unit 2 Corona treatments for two unwiders 2 cleaners UV Curing on 1 Flexo units (UV-Ray), which chilling rolls 2 die cutting units Chiller Blodpfx Afjyalqyj Aen Working hours 9000 Year of production 2006 more information on request If you have any questions or need more information, feel free to send us a message or give us a call.

Condition: new, Year of construction: 2026, machine/vehicle number: YC27-200T, functionality: fully functional, pressing force: 200 t, stroke length: 180 mm, operating speed: 8 mm/s, reverse speed: 140 mm/s, table width: 940 mm, table length: 740 mm, table height: 750 mm, throat depth: 400 mm, overall weight: 14,000 kg, Equipment: CE marking, documentation/manual, Digima YC27-200T Single-Column Press Hydraulic C-frame press with a 200-ton capacity for metal forming. The Digima YC27-200T is a modern, hydraulic single-column C-frame press designed for a wide range of metal forming processes. This machine is suitable for cutting, blanking, bending, light stamping, straightening shafts, and processing components requiring very high clamping forces. The C-frame design provides convenient access to the work area from three sides, facilitating material handling, workpiece positioning, and tool changes. The welded steel frame ensures high rigidity, minimizes deformation under load, and supports process repeatability. Key Advantages Why choose the Digima YC27-200T press? 200-ton capacity — very high working force for blanking, bending, stamping, and straightening components. C-frame design — access to the work area from three sides simplifies operation and tool changes. Welded steel frame — high rigidity, reduced deformation, and stability under load. Integrated valve block — compact hydraulic system design and rapid machine response. Fully enclosed drive — increased work safety and easier machine maintenance. Intuitive operation — lever-pedal system and control panel support comfortable operator use. Applications Where will the YC27 hydraulic press be useful? The Digima YC27-200T single-column press is designed for use in production facilities, tool rooms, maintenance departments, and industrial workshops where high clamping forces, convenient workpiece positioning, and a repeatable work process are required. Bending and forming — processing metal components using appropriate tooling. Blanking and cutting — working with parts requiring high, controlled clamping force. Light stamping — application in metal component forming processes. Straightening shafts and components — correction of machine components and technical parts. Tool rooms — assembly, fitting, testing, and servicing of production tools. Industrial production — repetitive operations with stable and safe working conditions. Technical Specifications: Model: YC27-200T Machine type: Hydraulic single-column C-frame press Nominal capacity: 2000kN/200ton Motor power: 18.5kW Maximum system pressure: 25MPa Stroke adjustment: 10-180mm Maximum slide stroke: 180mm Maximum mounting height / clearance: 80-380mm Table height from the ground: 750mm Slide dimensions: 770x580mm Table opening: 250mm Mounting hole: Ø70 mm Bledpjz Ari Tofx Af Ajn Throat depth / outreach: 400mm Fast descent speed: 21 mm/s Working speed: 8mm/s Return speed: 140mm/s External machine dimensions: 1800x2100x3600mm Machine weight: approx. 14000kg Type: Press Brand: Digima Condition: New Main application: Cutting, blanking, bending, light stamping, straightening shafts and components.

Condition: excellent (used), Year of construction: 2023, Pressing Lines for automatic multi-(2-3)-layer parquet production. Bsdpfx Asggflcef Aeln