Used Tire Recycling Plant for sale (18,727)

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, input current: 238 A, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h Tsdpfx Aovf E Avjc Nof bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: used, -Fuel delivery system -Biomass combustion system -Hot water boiler -Ash removal system -Flue gases primary cleaning system -Stairs and service platforms -Draft fan Todpfx Aowfpwpsc Nof - Automatic control system -Chimney -Circulation system and water treatment Main parameters and guarantee value are calculated according to fuel parameters: -Moisture 60-65 % -Ash till 8 % - Calorific value 7990 kJ/kg and 1907 kcal/kg Main parameters of the furnace 6000 K: - Maximal designed thermal output – 6.5 Mw - Maximum continuous rate – 6 MW - Furnace regulation range 20% - 100% - Volume of furnace- 31.6 m3 - Volume of combustion chamber – 24m3 - Grates area 12 m2 - Grates designed thermal load – 500 Kw/m2 - Combustion chamber designed thermal load – 250 Kw/m3 - Maximum temperature in the combustion chamber - 900°C The following kinds of biomass are accepted for combustion in the furnace: - wood chips – 100% - forest wood residues- 100% - saw dust – 100% (G15) - chunk peat – 100% - bark – 100%

Year of construction: 2010, condition: new, functionality: fully functional, Technical specifications: Todpoxm Uf Sofx Ac Nsf • Manufacturer: JMC Recycling Systems Ltd. (England) • Model: Dolphin 5005-Lite • Year of manufacture: 2010 • Connection: 380–415 V, 3-phase • Recommended hydraulic oil: ISO 46 • Robust construction, mobile on wheels • Includes control unit and hydraulic drive Condition: • NEW, unused • Only storage marks present (see pictures) • No operating hours

Condition: new, Year of construction: 2025, Also, different models are available! Tsdpfx Aogwcfzjc Nof IMPORTANT: MACHINE WILL BE BRAND NEW SEE THE TECHNICAL DESCRIPTION BELOW 1. Electric Motors Total Power: 2 x 45 = 90kW 2. Machine Weight: 12.000 kg 3. Shredding Capacity : 3 - 4 tons / h ( Aluminum profiles, barrels, fridge, etc steel thickness up to 3 mm and waste ) 4. Cutting blades are made of material HARDOX 500. Blade thickness is 6 cm and coated with HRC 60 hardfilled welding. Blades are easy to replace. 5. Loading Chamber Dimensions: 800 mm x 1200 mm 6. The walls will be covered with HARDOX 500 material. 7. Before painting, the whole machine body will be sandblasted. 8. Two cover undercoat and one cover paint will be applied. 9. The movement of the rotors is provided by an electric motor linked with a gearbox. 10. The rotors are moving independently of each other 11. The loading of the shredder can be done by grape or conveyors 12. In case of a jam between the rotor blades the machine turns the rotors in the opposite direction to remove the compression. 13. After the jam is solved the rotors return to their normal direction, If Jam is continuing the machine will stop with an acoustic warning. 14. A Hydraulic Oil cooling system is implemented. 15. Rotors are independent from each other and work at 18-20 rpm. 16. Hydraulic system components will be provided by PARKER or EATON-VICKERS & KAWASAKI brands. 17. All electrical parts will be SCHNEIDER and SIEMENS brands. 18. The machine is fully automatic with SIEMENS S7-1200 PLC control. 19. The machine is certified with ISO 9001 issued by URS, and CE issued by SGS. 20. Machine will be under AYMAS MAKINA San. Ve Tic. A. S. guarantees against manufacturing defects for one (1) year or two thousand five hundred (2.500) hours of operation.

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, Technical data on the EPS (Polystyrene) press: Manufacturer FZ-Recycling GmbH & Co. KG, Germany Type FZR 320 Year of construction 12/2022 Drive power shredder 4 kW Drive power of compactor screw 7.5 kW Drive power hydraulic unit for the holding clamp in the press channel 1.1 kW Total connected load 12.6 kW Current consumption 32 A Compaction ratio of the compacted blocks to the original product approx. 50:1 (depending on material) Tedpfou Thkaex Ac Njf Block weight after compaction approx. 300kg/m³ (depending on material) Block dimensions 320 x 320 mm, variable length Throughput approx. 100 kg/hour, depending on material Achievable density approx. 250 - 300 kg/m³ The pressed blocks are stacked approx. 1400 mm high on pallets and stretch-wrapped. Machine dimensions approx. 4,600 x 1,400 x 1,980 mm (l x w x h) Transport weight press 1,325 kg Condition of the baler: The press was only used sporadically, is in very good condition and available at short notice. Due to the low weight of the machine and the forklift shoes in the transport frame, the press is mobile and can be used directly on the construction site where the material is produced. The electrical connection is made via a CEE 32 A plug. Scope of delivery for the baler: 1 piece EPS press, ready for connection and use Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, Year of construction: 2025, MACHINERY WILL BE BRAND NEW The machinery is available to bale aluminum cans as well as steel cans up to 0.2 mm of the thickness and 3 liters of the volume. All electric-electronic materials will be from Schneider and Siemens Brand. The machine will be fully automatic with PLC control and a touch screen Siemens HMI Simatic Panel with emergency buttons. Machine will be under AYMAS Makina San. Ve Tic. A. S. Guarantee for one (1) year or two thousand five hundred (2.500) operation hours, whichever comes first. There will be an Oil cooling/heating system depending on the operation zone. MB 500 Magnetic Separator and VH (120-250) Vibration Hopper are optional for separating the scrap aluminum and steel cans and for getting rid of the dirt and dust in the scrap. Technical Specifications: Bale Size: 500mm x 330mm x ... Container Dimension (Width x Length x Height): 500mm x 1.000mm x 330mm Capacity Up to 1.000 kg/hour (Aluminum) Up to 2.000 kg/hour (Steel) Bale weighs with a mechanic scale system: 10-20 kg Cycle Time: 30 seconds Top Cover Cylinder Force: 25 tons Main Compression Cylinder Force: 100 tons General Working Pressure: 225 bars Machine Dimensions (Width x Length x Height): 1.100mm x 4.200mm x 2.600mm Electric Motor: 18,5 kW Machine Weight: 5.000 kg Todpfx Acorc Dkqe Nef

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: MACHINE WILL BE BRAND NEW Tjdpfevtw Iysx Ac Nsf SEE THE TECHNICAL DESCRIPTION BELOW 1. Electric Motors Total Power: 2 x 160 = 320kW 2. Machine Weight: 38.000 kg 3. Shredding Capacity : up to 6 tons / h ( Aluminum profiles, barrels, fridge, etc steel thickness up to 3 mm and waste ) 4. Cutting blades are made of material DIN 1.2746 Dimension : 105x105x49 mm . Blades are easy to replace. 5. Loading Chamber Dimensions: 2200 mm x 4500 mm 6. The walls will be covered with HARDOX 500 material. 7. Before painting, the whole machine body will be sandblasted. 8. Two cover undercoat and one cover paint will be applied. 9. The movement of the rotors is provided by an electric motor linked with a gearbox. 10. The loading of the shredder can be done by grape or conveyors 11. A Hydraulic Oil cooling system is implemented. 12. Rotor work at 20-30 rpm. 13. Hydraulic system components will be provided by PARKER or EATON-VICKERS & KAWASAKI brands. 14. All electrical parts will be SCHNEIDER and SIEMENS brands. 15. The machine is fully automatic with SIEMENS PLC control. 16. • The machine is CE certificated. The marking certifies that a product has met European Directives regarding consumer safety, health or environmental requirements. 17. Machine will be under AYMAS MAKINA San. Ve Tic. A. S. guarantees against manufacturing defects for one (1) year or two thousand five hundred (2.500) hours of operation.

Condition: new, Year of construction: 2025, IMPORTANT: MACHINE WILL BE BRAND NEW * The cutting guillotine is made of cast steel and is more resistant to fracture, buckling, and abrasion. * Cast steel cutting ram is subjected to a stress-relieving process. * The bolts of the blades on the cutting ram are monitored by the automation system and they are constantly kept tight by the hydraulic tightening system. Fracture and wear of the blades are minimized with this system, and 5 tons of force is applied to each bolt of the blades. * A hydraulic clamping system is used on both the moving and fixed parts of the blades. * Friction surfaces are coated with HARDOX 450 & 500 to prevent wear. * The machine has a fully automatic PLC control and a professional remote controller. * All electric-electronic components used are Schneider and Siemens Brands. Tedpfxodd Tp Rs Ac Nsf * Machine will be under AYMAS Makina San. Ve Tic. A. S. Guarantee for one (1) year or two thousand five hundred (2.500) operation hours, whichever comes first. SEE THE TECHNICAL DESCRIPTION BELOW: Cutting Force: 700 Tons Side Compression Force: 2x120=240 Tons (each wing) Clamp Compression Force: 120 Tons Pusher Ram Force: 120 Tons Electric Motor: 180 kW Machine Weight: 70.000 kg Cutting Width: 800 mm Box & Bale Size: 800 mm x 600 mm Box Length: 6.000 mm Box Width Opening: 350 mm Capacity: < 10 - 15 ton/h (Cutting Capacity), 15 - 20 ton/h (Baling Capacity)

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: MACHINE WILL BE BRAND NEW SEE THE TECHNICAL DESCRIPTION BELOW 1. Bale Size: 400mm x 400mm x... 2. Container Dimensions (Width x Length x Height): 1.000mm x 2.000mm x 800mm 3. Capacity: 4 tons/hour (Steel), 5 tons/hour (Copper), 2 tons/hour (Aluminium) 4. Cycle Time: 90 seconds ( Idle ) 5. Top Cover Cylinder Thrust: 90 tons 6. Preliminary Compression Cylinder Thrust: 150 tons 7. Main Compression Ram Thrust: 210 tons 8. Maximum Working Pressure: 300 bars Tjdpfx Acsdfc Iyj Nsf 9. Electric Motor: 37 kW 10. Machine Dimensions (Width x Length x Height): 3.400 mm x 6.800 mm x 3.000 mm 11. Machine Weight: 18.000 kg 12. There will be an ejection door. 13. Repairable and four-edge-usable blades. 14. Container walls will be covered with HARDOX 450 - 500 material. 15. There will be an automatic SKF liquid lubrication system integrated into the compression chamber. 16. There will be an automatic SKF greasing system that will grease the bushings. 17. Piston shafts will be induction-hardened and chrome-plated. 18. Pumps and valves used in the hydraulic system will be by PARKER or EATON VICKERS & KAWASAKI brand. 19. Bypass filter will be added to the hydraulic system. 20. There will be an AKG Hydraulic Oil Cooling System. 21. All electrical parts will be SIEMENS or SCHNEIDER Brand. 22. The machine will be fully automatic with PLC control, PLC brand and model will be SIEMENS. There will be a touch screen SIEMENS HMI Simatic Panel with emergency buttons placed on some important points. 23. There will be blades from 2767 material (hardness 55HRC) at the borders of the top cover and the sides of the scrap chamber. 24. Machine will be under AYMAS Makina San. Ve Tic. A. S. Guarantee for 1 year or 2.500 working hours whichever comes first against manufacturing defects.

Condition: new, Year of construction: 2025, 1. Electric Motors Total Power: 360 kW 2. Machine Weight: 44.000 kg 3. Shredding Capacity: 10 - 15 tons/h (Iron & Steel) 4. Blade Quantity: 78, Blade Thickness: 150 mm. 5. Loading Chamber Dimensions: 2350 x 4085 mm Tjdpfodfc Uzsx Ac Nof 6. Shredding Chamber Dimensions: 1500 x 2000 mm 7. Replacement and maintenance of the blades can be easily done from the top of the chamber. 8. Cutting blades are made of material No: 2767 9. Main shafts are made of material: 42 CrMo4, 32-34 HRC (Twisting and breaking resistant ) 10. All chamber walls will be covered with anti-wearing armor steel material HARDOX 500. 11. All static blades and distance rings will be made of HARDOX 450. 12. Speed: 4,5 – 6 rpm 13. The movement power of shafts will be provided by four planet reductors which are driven by four power-controlled bi-directional hydro motors. Hydraulic equipment will be PARKER brand or BOSCH-REXROTH. 14. There will be hydraulic oil and reducer oil cooling units separated from each other. 15. Each shaft will be able to move independently from each other. 16. The loading of the shredder can be done by crane 17. The machine will stop itself with an acoustic warning with the help of security sensors which are going to protect the machine against any harm. 18. There will be an automatic grease oiling system to keep bearings oiled automatically. 19. All electrical parts will be SCHNEIDER and SIEMENS brand. 20. The machine will be fully automatic with PLC control. There will be a touch screen on the control panel which will provide easy access to machine settings and process monitoring. 21. The machine will be under Aymas Makina San. Ve Tic. A. S. Guarantee against manufacturing defects for one (1) year or two thousand five hundred (2.500) operation hours. 22. The machine is CE certificated. The marking certifies that a product has met European Directives regarding consumer safety, health, or environmental requirements.

Condition: new, Year of construction: 2025, - Cutting Force : 1600 Tons - Capacity : up tp 70 tons per hour Tjdpfxsgv Acuj Ac Nef - Side Compression Force : 2 x 220 Tons - Clemp Compression Force : 250 Tons - Electric Motor : 480 kW - Machine Weight : 150.000 kg - PLC Controlled - Remote Control Avaliable - Output Length Adjustable

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: MACHINE WILL BE BRAND NEW SEE THE TECHNICAL DESCRIPTION BELOW 1. Bale Size: 500mm x 500mm x... 2. Container Dimensions (Width x Length x Height): 2.000mm x 2.500mm x 1.100mm 3. Capacity: 15-20 tons/hour (steel) 4. Cycle Time: 90 seconds ( Idle ) 5. Top Cover Cylinder Thrust: 90 tons 6. Preliminary Compression Cylinder Thrust: 150 tons 7. Main Compression Ram Thrust: 300 tons 8. Maximum Working Pressure: 300 bars 9. Electric Motor: 2 x 75 kW = 150 kW 10. Machine Dimensions (Width x Length x Height): 10.000 mm x 10.000 mm x 4.000 mm 11. Machine Weight: 55.000 kg 12. There will be an ejection door. 13. Repairable and four-edge-usable blades. 14. Container walls will be covered with HARDOX 450 - 500 material. 15. There will be an automatic SKF liquid lubrication system integrated into the compression chamber. 16. There will be an automatic SKF greasing system that will grease the bushings. 17. Piston shafts will be induction-hardened and chrome-plated. 18. Pumps and valves used in the hydraulic system will be by PARKER or EATON VICKERS & KAWASAKI brand. 19. Bypass filter will be added to the hydraulic system. 20. There will be an AKG Hydraulic Oil Cooling System. Todsgwa T Rspfx Ac Nof 21. All electrical parts will be SIEMENS or SCHNEIDER Brand. 22. The machine will be fully automatic with PLC control, PLC brand and model will be SIEMENS. There will be a touch screen SIEMENS HMI Simatic Panel with emergency buttons placed on some important points. 23. There will be blades from 2767 material (hardness 55HRC) at the borders of the top cover and the sides of the scrap chamber. 24. Machine will be under AYMAS Makina San. Ve Tic. A. S. Guarantee for 1 year or 2.500 working hours whichever comes first against manufacturing defects.

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: MACHINE WILL BE BRAND NEW SEE THE TECHNICAL DESCRIPTION BELOW 1. Briquette Diameter: Ø 80mm 2. Capacity: 700-900 kg/hour ( Copper ) 3. Preliminary Compression Ram Thrust: 12.5 tons 4. Main Compression Cylinder Thrust: 250 tons ( 5 tonne / cm2 ) 5. Maximum Working Pressure: 300 bars 6. Cycle Time: 12 - 14 seconds 7. Electric Motor Power: 30 kW 8. Machine Dimensions (Width x Length x Height): 2.200 mm x 2.600 mm x 2.800 mm 9. Machine Weight: 6.000 kg 10. Screw drive feeders will fill the compression chamber automatically and a built-in vibrating hopper will provide safety to the chamber by preventing the oversize material from entering the chamber. 11. Cylinder Rods are induction-hardened and chrome plated. Tjdpfx Acogwa Urj Nsf 12. A Hydraulic Oil cooling system is implemented. 13. Pumps and valves of hydraulic systems are from worldwide reputable brands such as PARKER. 14. The machine is fully automatic by PLC control. 15. All electrical and electronic parts are by SCHNEIDER or SIEMENS Brand. 16. The machine is CE certificated. The marking certifies that a product has met European Directives regarding consumer safety, health, or environmental requirements. 17. Machine will be under AYMAS Makina San. Ve Tic. A. Ş. Guarantee against manufacturing defects for one (1) year or two thousand five hundred (2.500) working hours.

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: THE MACHINE WILL BE BRAND NEW An Inclined Shear is a heavy-duty machine used in metal recycling facilities to cut various types of scrap materials efficiently. • Mixed and heavy-duty scrap can be processed (HMS 1 & 2, cars, pipes, etc. ) • No scrap length limit • No operator needed • Cut length adjustment options • Electric and Diesel options • Stationary and semi-mobile options • Hydraulic blade tightening system • The guillotine is made of casting • A remote diagnostic system is implemented • Automatic lubrication • Good output density • Heavy-duty structure • Chrome-plated & tampered shafts and sensitively honed cylinders • Special anti-wear plates • Reliable filtration system for the hydraulic oil • Reliable cooling system depending on the working climate • Top-brand hydraulic and electronic components The machine is CE-certified. The marking certifies that a product has met European Directives regarding consumer safety, health, or environmental requirements. Machine will be under AYMAS Makina San. Ve Tic. A. Ş. Guarantee against manufacturing defects for one (1) year or two thousand five hundred (2.500) working hours. SEE THE TECHNICAL DESCRIPTION BELOW Model: IS 1350 Cutting Force: 1.350 ton Hold Down Force: 250 ton Side Compression Force: 2x200 ton Cutting Width: 1.040 mm Number of Cuts: 2-3 cuts/min. Capacity up to 50 ton/h Weight: 128 ton Electrical Motor Power: 3x132 kW Chamber Dimensions: (W x L) 2,45 m x 8,5 m. General Dimensions: (W x L) 4,6 m x 11 m. Tjdpfx Ajgv Abpsc Njf

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: MACHINE WILL BE BRAND NEW SEE THE TECHNICAL DESCRIPTION BELOW 1. Briquette Diameter: Ø 160mm 2. Capacity: 4.500 – 5.500 kg/hour (Iron & Steel) Tjdpfogv I Ihjx Ac Nsf 3. Preliminary Compression Ram Thrust: 50 tons 4. Main Compression Cylinder Thrust: 600 tons 5. Maximum Working Pressure: 300 bars 6. Cycle Time: 12 - 14 sec 7. Electric Motor Power: 170 kW Overall 8. Machine Dimensions (Width x Length x Height): 5.200mm x 8.000mm x 3.100mm 9. Machine Weight: 42.000 kg 10. Screw drive feeders will fill the compression chamber automatically and a built-in vibrating hopper will provide safety to the chamber by preventing the oversize material from entering the chamber. 11. Cylinder Rods are induction-hardened and chrome plated. 12. A Hydraulic Oil cooling system is implemented. 13. Pumps and valves of hydraulic systems are PARKER or BOSCH-REXROTH brand. 14. The machine is fully automatic by PLC control. 15. All electrical and electronic parts are by SCHNEIDER or SIEMENS Brand. 16. The machine is CE certificated. The marking certifies that a product has met European Directives regarding consumer safety, health, or environmental requirements. 17. Machine will be under AYMAS Makina San. Ve Tic. A. Ş. Guarantee against manufacturing defects for one (1) year or two thousand five hundred (2.500) working hours.

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: MACHINE WILL BE BRAND NEW. SEE THE TECHNICAL DESCRIPTION BELOW 1. Briquette Diameter: Ø 200mm 2. Capacity: 12.000 kg/hour ( Steel) 3. Preliminary Compression Ram Thrust: 50 tons 4. Main Compression Cylinder Thrust: 850 tons 5. Maximum Working Pressure: 300 bars 6. Cycle Time: 10 - 12 sec 7. Electric Motor Power: 6x37=222 kW (Main Motors) 8. Machine Dimensions : 11.000mm x 10.000mm 9. Machine Weight: 60.000 kg 10. Screw drive feeders will fill the compression chamber automatically and a built-in vibrating hopper will provide safety to the chamber by preventing the oversize material from entering the chamber. Tedpfx Acogv I N Uj Njf 11. Cylinder Rods are induction-hardened and chrome plated. 12. A Hydraulic Oil cooling system is implemented. 13. Pumps and valves of hydraulic systems are PARKER or BOSCH-REXROTH brand. 14. The machine is fully automatic by PLC control. 15. All electrical and electronic parts are by SCHNEIDER or SIEMENS Brand. 16. The machine is CE certificated. The marking certifies that a product has met European Directives regarding consumer safety, health, or environmental requirements. 17. Machine will be under AYMAS Makina San. Ve Tic. A. Ş. Guarantee against manufacturing defects for one (1) year or two thousand five hundred (2.500) working hours.

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: THE MACHINE WILL BE BRAND NEW The compression chamber walls are covered with HARDOX material for long-term life-cycle and friction resistance. A hydraulic Oil Cooling system is implemented for efficiency in hot climate conditions. Cylinder Rods are induction-hardened and chrome-plated. Pumps and valves of hydraulic systems are from worldwide reputable brands such as PARKER, and BOSCH-REXROTH. The machine is fully automatic by PLC control. It is easy to use with the help of the touch screen. All electrical and electronic parts are by SCHNEIDER and SIEMENS Brands. The machine is CE-certified. The marking certifies that a product has met European Directives regarding consumer safety, health, or environmental requirements. Todpfxsdfcqao Ac Nof Machine will be under Aymas Makina San. Ve Tic. A. Ş. Guarantee against manufacturing defects for one (1) year or two thousand five hundred (2.500) working hours. SEE THE TECHNICAL DESCRIPTION BELOW Bale Size 400mm x 400mm x... Bale Weight 120-180 kg (Steel), 50-80 kg (Aluminium),150-200 kg (Copper) Press Box Dimensions (Width x Length x Height): 1.000mm x 2.700mm x 900mm Loading Bunker Dimensions (Width x Length x Height): 1.650mm x 2.300mm x 800mm Feeding Opening: 1.000mm x 1.600mm Capacity*

Condition: new, Year of construction: 2025, - Cutting Force : 700 Tons Todpfogv Aacsx Ac Nof - Capacity : up tp 20 tons per hour - Side Compression Force : 2 x 85 Tons - Clemp Compression Force : 100 Tons - Electric Motor : 160 kW - Machine Weight : 55.000 kg - PLC Controlled - Remote Control Avaliable - Output Length Adjustable

Year of construction: 2024, condition: new, - Cutting Force : 1100 Tons - Capacity : up tp 50 tons per hour - Side Compression Force : 2 x 120 Tons - Clemp Compression Force : 160 Tons - Electric Motor : 264 kW - Machine Weight : 85.000 kg - PLC Controlled - Remote Control Avaliable Todpfxodfcpae Ac Njf - Output Length Adjustable

Condition: new, Year of construction: 2025, - Cutting Force : 900 Tons - Capacity : up tp 25 tons per hour - Side Compression Force : 2 x 120 Tons - Clemp Compression Force : 160 Tons - Electric Motor : 220 kW - Machine Weight : 78.000 kg - PLC Controlled Tsdpjgv Aa Iefx Ac Nof - Remote Control Avaliable - Output Length Adjustable

Condition: new, Year of construction: 2025, IMPORTANT: MACHINE WILL BE BRAND NEW Tsdpfxsgwcc Ao Ac Njf SEE THE TECHNICAL DESCRIPTION BELOW 1. Electric Motors Total Power: 180 kW 2. Machine Weight: 20.000 kg 3. Shredding Capacity: 10 t/h (Steel) 15 t/h (Copper) 4. Blade Quantity: 90, Blade Thickness: 100 mm. 5. Loading Chamber Dimensions: 1.600 mm x 2.400 mm 6. Shredding Chamber Dimensions: 1.000 mm x 1.600 mm 7. Replacement and maintenance of the blades can be easily done from the top of the chamber. 8. Cutting blades are made of material No: 2767 9. Main shafts are made of material: 42 CrMo4, 32-34 HRC (Twisting and breaking resistant ) 10. All chamber walls will be covered with anti-wearing armor steel material HARDOX 500. 11. All static blades and distance rings will be made of HARDOX 450. 12. Speed: 4 – 6 rpm 13. The movement power of shafts will be provided by four planet reductors which are driven by four power-controlled bi-directional hydro motors. Hydraulic equipment will be PARKER brand or BOSCH-REXROTH. 14. There will be hydraulic oil and reducer oil cooling units separated from each other. 15. Each shaft will be able to move independently from each other. 16. The loading of the shredder can be done by crane 17. The machine will stop itself with an acoustic warning with the help of security sensors which are going to protect the machine against any harm. 18. There will be an automatic grease oiling system to keep bearings oiled automatically. 19. All electrical parts will be SCHNEIDER and SIEMENS brand. 20. The machine will be fully automatic with PLC control. There will be a touch screen on the control panel which will provide easy access to machine settings and process monitoring. 21. The machine will be under AYMAS Makina San. Ve Tic. A. S. Guarantee against manufacturing defects for one (1) year or two thousand five hundred (2.500) operation hours. 22. The machine is CE certificated. The marking certifies that a product has met European Directives regarding consumer safety, health, or environmental requirements.

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: THE MACHINE WILL BE BRAND NEW The compression chamber walls are covered with HARDOX material for long-term life-cycle and friction resistance. A hydraulic Oil Cooling system is implemented for efficiency in hot climate conditions. Cylinder Rods are induction-hardened and chrome-plated. Pumps and valves of hydraulic systems are from worldwide reputable brands such as PARKER, and BOSCH-REXROTH. The machine is fully automatic by PLC control. It is easy to use with the help of the touch screen. All electrical and electronic parts are by SCHNEIDER and SIEMENS Brands. The machine is CE-certified. The marking certifies that a product has met European Directives regarding consumer safety, health, or environmental requirements. Machine will be under AYMAS Makina San. Ve Tic. A. Ş. Guarantee against manufacturing defects for one (1) year or two thousand five hundred (2.500) working hours. Todpfx Aod Iya Njc Nsf SEE THE TECHNICAL DESCRIPTION BELOW Bale Size 400mm x 400mm x... Bale Weight 100-180 kg (Steel), 40-100 kg (Aluminium),120-180 kg (Copper) Press Box Dimensions (Width x Length x Height): 1.000mm x 2.600mm x 900mm Loading Bunker Dimensions (Width x Length x Height): 1.500mm x 2.200mm x 650mm Feeding Opening: 1.000mm x 1.600mm Capacity*

Condition: new, Year of construction: 2025, Also, different models are available! IMPORTANT: MACHINE WILL BE BRAND NEW SEE THE TECHNICAL DESCRIPTION BELOW: 1. Briquette Diameter: Ø 120mm 2. Capacity: 1.800 – 2.200 kg/hour (Iron & Steel) 3. Preliminary Compression Ram Thrust: 15 tons 4. Main Compression Cylinder Thrust: 400 tons 5. Maximum Working Pressure: 300 bars 6. Cycle Time: 12 - 14 sec 7. Electric Motor Power: 75 kW 8. Machine Dimensions (Width x Length x Height): 3.200mm x 4.200mm x 3.500mm 9. Machine Weight: 13.000 kg Tjdedfc Ikopfx Ac Njf 10. Screw drive feeders will fill the compression chamber automatically and a built-in vibrating hopper will provide safety to the chamber by preventing oversize material from entering the chamber. 11. Cylinder Rods are induction-hardened and chrome plated. 12. A Hydraulic Oil cooling system is implemented. 13. Pumps and valves of hydraulic systems are PARKER or BOSCH-REXROTH brand. 14. The machine is fully automatic by PLC control. 15. All electrical and electronic parts are by SCHNEIDER or SIEMENS Brand. 16. The machine is CE certificated. The marking certifies that a product has met European Directives regarding consumer safety, health, or environmental requirements. 17. Machine will be under AYMAS Makina San. Ve Tic. A. Ş. Guarantee against manufacturing defects for one (1) year or two thousand five hundred (2.500) working hours.

Condition: new, Year of construction: 2024, Technical Specifications: Maximum Cable Diameter: Ø 90mm Tjdpfx Acod Imwfo Nsf Minimum Cable Diameter: Ø 5mm Cutting Speed: 10 m / min Electric Motor Power: 4 kW Machine Dimensions : 70cm x 131,5cm x 119cm Machine Weight: 460 kg • With the help of the “Safety System Stop” bar, operating accidents are reduced. • All electric-electronic materials will be SCHNEIDER and SIEMENS. • Machine will be under Aymas Makina San. Ve Tic. A. Ş. Guarantee against manufacturing defects for one (1) year. • The machine is CE certificated. The marking certifies that a product has met European Directives regarding consumer safety, health, or environmental requirements.

Condition: new, Year of construction: 2025, Capacity: 1000 - 1500 kg/hour Tsdpfx Aod Im Adoc Nof Electric Motor Power: 15 kW Machine Weight: 1800 kg