Sandblasting system, blasting hall

Oliver Fritz GmbH & Co. KG Strahlhaus Easy 10mx5mx5m LxBxH

Condition: new, overall weight: 47,000 kg, axle configuration: 2 axles, Year of construction: 2025, Technical data MAX510-Z-2H-ATX-A-6.85-PA Speed: 80 km/h Total weight: 47,000 kg Fifth wheel load: 23,000 kg Axle load: 24,000 kg Gooseneck length: 3,750 mm Fifth wheel height loaded: 1,200 mm Steering radius to the rear: 2,300 mm Loading area length: 6,850 mm Extendable by: 5,500 mm Loading height with max. load: 350 mm Chassis length: 2,600 mm Loading height of rear chassis with max. load approx: 1,005 mm Suspension travel: -150/+450 mm Axle spacing: 1,360 mm Total width: 2,540 mm Total weight depends on fifth wheel load. Low bed: Low bed with external supports in extendable design "SUPER LOW" design, length approx. 6,850 mm. Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking. The supply lines are protected in the extendable supports and automatically adjust to the respective low bed length. 5 pairs of lashing rings that can be folded outwards (LC 10,000 daN). 6 pairs of threaded blocks on the inner support for mounting screwable RUD rings. Rear chassis: Rear chassis with closed outer frame, checker plate covering and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear. 2 pairs of lashing rings that can be folded outwards (LC 10,000 daN). 1 pair of tension rings lying in the trough (LC 8,000 daN+5,300 daN). 2 pairs of stake pockets for 100 x 50 mm stakes in the outer frame Nodjizu Nwjpfx Abbowp Gooseneck: Gooseneck in SNT design to optimize the loading area length, length approx. 3,785 mm. Gooseneck can be raised/lowered hydraulically and removed. Technical fifth wheel load: 23,000 kg For tractor units: 4 x 2, 6 x 2 and 6 x 4 PENDEL-AXLE: "PENDEL-AXLE", all axles hydro-mechanically forcedly steered. Hose rupture valve on the axle compensation cylinder with automatic RESET function. Hydraulic cylinder with shut-off valves and pins for securing in raised position. Final painting of the axles with 2 layers of 2-component paint in a single color in "FAY-Gray-34-0260". Technical axle load: 12,000 kg Hydraulic axle compensation. Axle tool. Braking system: Braking system in accordance with EU regulations with EBS-E (2S2M) without connecting cables to the tractor unit. Electrical system: Electrical system in accordance with EU regulations, lighting 24 volts ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets. Connection in accordance with ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel construction: Steel construction made of high-strength fine-grain steels. Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Paint: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) top coat in a single color in RAL colors of your choice. Rear section metallized and painted in RAL 9010 (pure white). No metallic paint possible. Tires: Tires 245/70 R 17.5 3PMSF At the manufacturer's discretion. Load index (146/146F) Preparation for screw-on container positioning for 1x 20' or 1x 40' container on the outer supports. Without container locks. i i2" kingpins iA galvanized steel bulkhead, approx. 400 mm high. iA spare wheel with holder in front of the bulkhead. i2 brake shoes with holder on the bulkhead. iYellow-red air couplings on the galvanized connection strip at the front. Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles. (without insta

Condition: new, Year of construction: 2024, SEMI-AUTOMATIC DRILLING RIG “UNIBORFIX 50” With the UniBohrFix 50 drilling system, all profiles can be machined against a stop or with grippers. The Drilling is done manually using the lever, with the materials on the X-axis automatically pointing to the drive to the next drilling position. Easily drill entire programs or work with the stop plate quickly carry out individual drillings. The system is suitable for weights up to 100 kg. The facility also contains a minimum quantity spray unit with holder and spray can. The technical data of the standard version can be found in the table. If necessary, all components of the system can be adapted to your requirements. You can choose between different drilling machines, roller conveyors, Nodpsgwt Slefx Abbewp select positioning systems and vices. Plantec configures the system so that it suits you perfectly! ADVANTAGES A sequence of holes is automatically executed at precise intervals. Potential operator errors are drastically reduced. Programming takes just a few minutes. Very good value for money. Significant reduction in manpower. Standard measuring lengths: 3,000mm 6,000mm Drill: Unimax 2 T Spindle MK2 Continuous drilling capacity 18 mm Speed ​​ranges: 100-2000rpm, 200-4000rpm Projection 225 mm Spindle/table distance 60-400 mm Adjustable vice with measuring linear display Positioning length stop: PD-100e control for automatic positioning Positioning: absolute or chain dimensions Easy to read LED display Trolley with DC servo motor Positioning accuracy +/- 0.1 mm/m Attachment arm with spring damping Stop plate with groove Memory control with 3,000 memory options Roller conveyors: RD-200/3 load capacity 200 kg/m Roll width 290 mm Roll diameter 40 / 50 mm insert sheets Struts for stabilization switch cabinet Available options: Minimum quantity spray system with spray head and holder Gripper tongs for clamping the material on the stop plate

Condition: new, Cardan shaft balancing machine BVI-03-74 Available in stock in Poland !!! Delivery time: one day!!! . . Machine for driveshafts weighing up to 150kg and up to 4700mm long. Suitable for small workshops with a large range of different shafts, including trucks. This balancing machine has high productivity and serves to balance the cardan shafts of cars and trucks. It makes the process of balancing the cardan shaft easy thanks to many technical solutions, while the machine has an affordable price, which reduces your financial burden and allows you to develop your business effectively. . . TWO TIMES faster than your machine. This balancing machine is majored to balance the shaft not only qualitatively, but also quickly. If you can balance in 2-2.5 times faster, then this is your real competitive advantage. . . HIGH PERFORMANCE ACCESSORIES The machine is equipped with three main types of adapters: 1. Fast clamping universal adapters. It has two main advantages: The first is that due to the special design the driveshaft flange is clamped within 5 seconds. This advantage is due to the fact that the driveshaft flange does not need to be fixed with bolts. THE SHAFT CAN BE CLAMPED 4 TIMES FASTER WITHOUT BOLTS. The second advantage is the centering rings. The driveshaft is mounted in the adapters with centering rings that can be made on an ordinary lathe to fit most common driveshafts. 2. KV Flange adapters. Used for balancing shafts with cross-tooth flanges. Applies to four flange sizes: 120, 150, 180, 205 mm. Usually used on truck driveshafts. 3. Adapter with slots. Used to mount various flanges with holes. Mounting the driveshaft is the same as on universal adapters, with the help of centering rings. Nwodpfxspbv Tfj Abbop KEY FEATURES • Balancing of 2, 3 and 4-support cardan shafts • Shaft length up to 4700mm, weight up to 150kg • Cardan installation in 1 minute • Standard set of adapters - Installation of 80% of cardan shafts; • Three ways of fixing the center bearing • Soft-bearing type machine - high sensitivity to any vibration • Machine is operated by one worker • Sliding bearing supports - quick changeover, comfortable operation • Safety bracket with clamp for quick installation • Measurement in all planes at one time • Calibration of the machine by the operator • Displays imbalance in real time • Create and print reports SPECIFICATIONS Maximum cardan shaft weight 150 kg Maximum flange diameter 300 mm Maximum length of cardan shaft 4700 mm Number of machine supports 4 Number of simultaneously measured planes 2, 3, 4 Minimum achievable residual specific imbalance, 10 g mm/kg Rotor speed range 1000-2000 rpm Power supply 380V, 3 Ph, 50Hz Power, minimum, 2,2 kW Dimensions (length x width x height) 6000 х 1100 х 1450 mm Weight 700 kg ! We manufacture а full range of equipment for drive shaft balancing and repair service. Please contact us to get the best offer!

Condition: excellent (used), Year of construction: 2023, operating hours: 1,851 h, functionality: fully functional, pressing force: 70 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 500 kg, overall weight: 17,000 kg, oil tank capacity: 70 l, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410 BS-22/50 Year of construction 2023 Pump operation hours 1,851 hours, as of July 24 Press power main press 70 t (a 70 tonne hydraulic cylinder is installed, special equipment) Specific press force 90,9 N/cm² (a 70 tonne hydraulic cylinder is installed, special equipment) Feed channel 1,400 x 1,000 mm Theoretic cycle time 13 sec Theoretic throughput capacity 266 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 22 kW Connected load 65 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 5,5 t/h bulk weight of 50 kg/cbm approx. 7,5 t/h bulk weight of 100 kg/cbm approx. 9,7 t/h Bale weight with a bale length of approx. 1.2 m up to 500 kg, depends on material SPS controller Siemens S7-1500 Operating panel Schneider Harmony Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 17 t Special equipment: Wear-resistant floor made of HARDOX steel Larger main hydraulic cylinder with 70 tonnes of pressing force Special press ram for pressing loose bulk materials with small grain sizes OptiCut XS system for lower cutting forces and higher throughput rates Special pressing piston for pressing "difficult" materials Technical data for the conveyor belt: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Deutschland Type KGF GB 1500 Year of construction 2023 Drive power 4.0 kW Belt speed approx. 0.3 m/second Length feeding conveyor 2,679 mm Length elevating conveyor 6,866 mm Length goose neck 1,272 mm Grade 35° Effecting width 1,400 mm Side wall height 800 mm Carrier height 50 mm Carrier distance 750 mm Belt quality EP 400/3, 3:1 (DIN quality N) Overall height 4,515 mm Overall transport dimensions11,148 x 2,502 mm (l x w) Technical data on the non-contact personal protection system: Manufacturer BOREMA Umwelttechnik AG, Switzerland Type APSS iBOR 22 Year of construction 2023 Condition of the press system: The entire system is in very good condition due to the short operating time of only 1,851 pump hours and the processing of only paper, cardboard and film. Scope of delivery: Avermann baler, type AVOS 1410 BS-22/50, incl. wire drawing stations and bale chute Nodju Thbxopfx Abbswp Avermann conveyor belt, type KGF GB 1500 BOREMA personal protection system, type APSS iBOR 22 Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 2004, overall weight: 40,000 kg, pressing force: 450 t, AXIAL 4100x450tn + Cybelec ModEva 10 + 5 axes (Y1, Y2, X, R, Z) + WILA cnc compensation table + WILA hydraulic punch and die clamp Bending length: 4.100mm Force: 450tn Cursa: 365mm Axes: 5 axes (Y1, Y2, X, R, Z) Nwsdpfx Abeu Au U Tebjp *Z-axis (double prismatic guide nipples) WILA hydraulic clamping of punch and die WILA cnc compensation table Trancha working speeds: Approach speed: 110mm/sec. Working speed: 8mm/sec. Up speed: 90mm/sec Distance between uprights: 3600mm Neckline: 410mm Opening between table and truss: 500mm Pit penetration: 975mm Cnc: Cybelec ModEva 10 (Control CPU New as of September 2023) Laser safety: DSP LASER - TX Weight: 40tn Motor power: 30KW

Condition: excellent (used), Year of construction: 2012, section dimension max. 150 x 50 mm pipe Ø 50 – 150 mm wall thickness 1,5 - 5,5 mm reference material (tensile strength) 600 N/mm² coil Ø max. 2.100 mm coil weight max. 10 t finish pipe length max. 9.000 mm round pipe Ø according to list rectangular pipe according to list speed 100 m/min working direction left → right The line consists of: 1. entry part: double carousel decoiler Njdpfx Asuc Sw Asbbewp coil opener/pinch roll unit/leveller crop shear strip tail end welding machine strip guide strip twister/pinch roll unit/strip accumulator entry strip accumulator edge trimming exit twister 2. forming part: No. of horizontal stands: 4 No. of vertical stands: 3 3. welding part (HF) 4. calibrating part 5. separation 6. edge bevelling 7. blowing out 8. bundling 9. hydraulics 10. electrics

Condition: new, Year of construction: 2025, -Tfon Leveltech® TF M-5516 Leveling Machine Engineered for precision leveling, the TF M-5516 efficiently handles material thicknesses from 1 to 15 mm with advanced control features for optimal performance and ease of use -Key Specifications -Material Thickness: 1 – 15 mm -Maximum Material Width: 1,600 mm Minimum Material Length: 110 mm. Quick Change System for Straightening Rollers: Standard Flattening Gap Adjustment: Servo Hydraulic / PC Controlled Overload Protection: Standard Control Screen: Touchscreen Nsdpfx Abjkyrqfjbjwp Machine Size (L × W × H): 3,500 × 2,905 × 1,950 mm Total Weight: 19.000 kg.

Condition: excellent (used), Year of construction: 2007, Zeppelin Diesel Genset Type: PPO2000 - C32 Serial No.: ZPSU1023; Arr.No: 273-9683; Year: 2014; Voltage [V]: 400; Rating [kW]: 1600; Rating [kVA]: 2000; speed [RPM]: 1500; Frequency [Hz]: 50; SMU [hrs]: 0; Application: prime; Layout: Canopy; condition: pre-owned; Notes: Diesel Engine 2 * CAT C32 PPO, new Stamford HC6J alternator, with ComAp automatic Panel Inteli Compact, 2 x circuit breaker, 4000 L in two fuel tank, Jacketwater heater. L/W/H: 11 m,/ 2,3 m/ 3,2 m, weight. 26t, Import duty unpaid. Njdeizbdaepfx Abbswp

Condition: good (used), turning diameter: 5,000 mm, travel distance Z-axis: 2,000 mm, turning length: 2,500 mm, The machine is in good technical condition, fully functional, modernized in 2008. It is equipped with a Siemens Sinumerik 802 D control system, a maximum turning diameter of 5000 mm and a clamping plate diameter of 2500 mm. The workpiece weight is 40 tons and the height is 2000 mm. Nedpfx Asv Dkyksbbowp

Condition: used, Year of construction: 2015, machine/vehicle number: 5319, travel distance X-axis: 8,000 mm, travel distance Y-axis: 2,600 mm, travel distance Z-axis: 1,300 mm, BASIC MACHINE PowerSpeed 5 WITH FORK HEAD – KEY TECHNICAL DATA Travels: X-axis: 8,000 mm Y-axis: 2,600 mm Z-axis: 1,300 mm Machine bed (X-axis): Flat-bed design with 1,000 mm guideway width. Two electric motors drive via a centrally bolted rack. Hardened compact roller guides ensure high precision. Machine base (Y-axis): Welded steel construction with 900 mm guideway width. Two liquid-cooled feed motors and two measuring systems ensure dynamic performance and accuracy. Protected by telescopic steel covers. Headstock slide and headstock: Made of GGG 60 cast iron, guided by compact roller guides. Optimal power transmission thanks to long guideways and close arrangement of the Y and Z axes. Dual-spindle drive: Two vertical ball screws with separate drives and measuring systems for high dynamics and long-term accuracy. Drive system: Individual digital drives with AC motors. Feed and rapid traverse range: 2–30,000 mm/min. Acceleration: 3.5 m/s². Measuring system: Direct, non-contact linear measuring systems for high manufacturing accuracy. Nodjwdub Depfx Abbswp Automatic 2-axis yoke head with motor spindle: A-axis: 764 Nm (100% duty cycle), ±105°, clamping torque 2,160 Nm, accuracy ±5″ C-axis: 810 Nm (100% duty cycle), ±200°, clamping torque 3,024 Nm, accuracy ±3″ Motor spindle: HSK-A 63, up to 18,000 rpm, 89 Nm (100% duty cycle), internal/external coolant supply up to 70/20 bar, liquid-cooled Electrical equipment: 400/230V, 50Hz, 80kVA power rating. Control cabinet (IP54) with control and switching devices. Machine-to-cabinet cable length: 5m. Control cabinet cooling: Two-chamber system with automatic internal air cooling and dehumidification. Lubrication: Centralized lubrication for guides, permanent grease lubrication for the main spindle, oil mist lubrication in the milling head. Power supply: Compressed air 4–6 bar, G 1/4 connection, with filter pressure regulator and condensate separator. Control: Siemens 840D sl with swiveling control panel. Wireless handwheel with LCD display, potentiometers, and buttons for axes, feed, and spindle. Remote maintenance: Fault diagnosis via alarm manager, notification via email/SMS (SIM card and network required). TightBlock base frame (X = 8,000 mm): Solid composite construction for damping. Foundation recommendation: ≥100 mm thickness per 1,000 mm of X-travel, structurally tested. Coolant system: 500 l tank, filter system