Vacuum nitriding furnace (Vacuum nitriding)

RUBIG GN 240/175

Year of construction: 1984, condition: ready for operation (used), Rafamet UBB 112/2 Kwodpohvml Iofx Adwst Wheel Tread Diameter Minimum 700 mm Wheel Tread Diameter Maximum 1120 mm Clamping length 540 - 1050 mm Wheelset Axle Length Minimum 1640 mm Wheelset Axle Length Maximum 2800 mm Maximum Tire Width 150 mm Maximum Wheelset Weight 4000 kg Saddle Set Up Motion Speed 2000 mm/min Saddle Feed Maximum 2000 mm/min Main Drive Motor Power 80 kW Weight aprox 40000 kg

Year of construction: 2021, condition: new, type: gas-fired with central recuperator max. temperature: 1300°C max. furnace output: approx. 700 kg/h clear door opening (w x h): 600 x 400 mm number of burners: 6 number of control areas: 3 heating capacity: 720 kW el. total connected load: approx. 15 kVA Ksdpog E S Injfx Adwswt PLC: Siemens S7

Condition: excellent (used), Year of construction: 2005, travel distance X-axis: 600 mm, travel distance Y-axis: 450 mm, travel distance Z-axis: 400 mm, rapid traverse X-axis: 35,000 m/min, rapid traverse Y-axis: 35,000 m/min, rapid traverse Z-axis: 35,000 m/min, workpiece weight (max.): 200 kg, total length: 500 mm, total width: 400 mm, table load: 200 kg, rotary table diameter: 280 mm, Coolant system Filtration tank HR 410 Handwheel iTNC530 controller 1e owner machine X - Travel: 600mm Y - Travel: 450mm Z - Travel: 400mm A - Axis: 110° B - Axis: 360° Kwodpsx R S Smofx Adwet Table Length: 500mm Table Width: 400mm Table load: 200 Table Ø: 280mm Feed rate X-Axis: 35000mm/min. Feed rate Y-Axis: 35000mm/min. Feed rate Z-Axis: 35000mm/min. Feed rate A-Axis: 10Degrees/min Feed rate B-Axis: 15Degrees/min Spindle Taper: 40ISO/Bt/Mk Power on spindle: 15kW Speeds / ranges: 18000Rpm ATC / revolver: 30 Coolant through spindle / Bar:20 Number of controlled axis: 5 Chip conveyor: Yes Coolantsystem: Yes Length: 3500mm Width: 3500mm Height: 2800mm Weight: 6600kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Year of construction: 2004, Clampable cutter head type (max.) 460 mm Cutter head weight (max.) 150 kg Mounting disc diameter for cutter heads (Ø) 360 mm Mounting cone for cutter heads Nominal diameter Ø 58,227 mm travel -z axis 200 mm diagram-drawing enlargement ±10 - ± 500 µm Kwsdpfx Adjul Efmewst weight of the machine ca. 2,3 t dimensions of the machine ca. 2 x 1,5 x 2,03 m In the manufacturing process for spiral-toothed bevel gears, the quality of the gear cutting gear cutting tools used plays a decisive role. Particularly in high gear cutting quality and a long service life can only be achieved with precisely can only be achieved with precisely adjusted cutterheads. The Oerlikon cutterhead setting and testing device CS 200 enables quick and easy setting of the individual knives and simple adjustment of the individual knives, it checks the position and documents the measurement results. The measuring sequence on the CNC-controlled testing device is partially automated: The individual actions for carrying out the actions for carrying out the sequence are displayed on the screen via the operator guidance. The positioning of the individual knives in the cutter head and the height of the knife tips is largely automatic thanks to a special sequence and is simultaneously documented by means of a run-out diagram. A subsequent measuring sequence checks the radial position of the inner and outer cutting edges of all knives in the cutterhead. If individual test parameters on the knives do not correspond to the the tolerance specifications, this can be individually repositioned. The combination of semi-automated setting sequence, operator-guided set-up actions and automatic operator-guided set-up actions and automatic measuring sequence, cutterheads can be can be set conveniently, quickly and with high precision. Operator-guided setting and test sequence - Graphic display of the cutter head design and the measurement results with tolerance check - Instructions for the operator in plain text Instructions for the operator in plain text (without coded information) - Simple assignment of the measurement results to the knives - Documentation of the setting and measurement results via printer- Setting and test sequence suitable for ARCON®, RSR, Spirapid, SPIRON®, TRI-AC® types - Interface for neutral data

Condition: used, sweeping width 800 tenb. container volume 114 l total power requirement 3,0 kW 2759 m²/h max. 5232 m²/h Sweeper - scrubber dryer Operating hours: approx. 400 hours incl. 4x brush + charger Kedpfx Adeg Ti Ihewewt including new battery pack (consisting of 6x gel battery) !!

Condition: good (used), Waelz piston blower Manufacturer: Leybold Type: RUVAC WAU 1001 Kjdpfx Aeb Rnfisdwjwt Cat.-No.: 11741 suction capacity: approx. 1000m³/h Status: Refurbished Warranty: 12 months Delivery time: ex stock

Condition: used, HYDRAULIC DOUBLE COLUMN PRESS CAMP 250 tn Double column press Pressing power 250 tn Stroke of the piston 500 mm Table size 570 x 570 mm Distance from table to piston 600 mm Ksdpfx Adogr Ur Rewjwt Distance between uprights 570 mm Approach speed 95 mm/seg Workin speed 7.5 mm/seg Retraction speed 135 mm/ seg Engine power 30 cv

Condition: used, Year of construction: 1965, honing diameter 80 mm stroke 280 mm throat 300 mm total power requirement 6 kW weight of the machine ca. 2,6 t Honing Ø 10 - 100 mm Max. honing depth, approx. 250 mm Max. spindle stroke 260 mm Kwjdpst Hwupsfx Adwjt Distance between spindle and column 300 mm Mounting height 1,000 mm Table size 350 x 500 mm Height of table above floor 500 mm Spindle speeds in 2 steps, infinitely variable, approx. 85 - 300 rpm 170 - 600 rpm Stroke speed, infinitely variable, hydraulic 0 - 23 m/min Spindle drive 2 kW Total electrical load 6 kW - 380 V - 50 Hz Weight 2,600 kg Accessories / Special Features * Built-on 2-station tilting table which accommodates 2 workpieces. Mechanical workpiece clamping, using a manual lever. * Hydraulic infeed of the tool. * Switch-off via timer. * Air measuring device (probably). * Honing oil unit. * Various splash shields, etc. Condition : Good. Machine can be inspected under power. Delivery : Ex stock, as inspected. Payment : Net, after conclusion of contract. Thank you for your interest. We have a selection of honing machines available. Please let us know what you need.

Year of construction: 2022, condition: as good as new (ex-display), Manipulator with hydraulic height adjustment, face plate with clamping slots and manual remote control. Height (face plate horizontal): approx. 532 - 1.132mm Lifting distance/lifting time (hydraulic): approx. s = 600mm, t = 20s Swivel range of face plate: approx. +-300°. Height (Pl.-sch.vertical axis): approx. 709mm Ksdofw Ah Rjpfx Adwowt Dimensions face plate: Ø1.200mm x 40mm, 6x clamping slots Speed of the main axle: approx. 2.0 rpm (other Torque main axis of rotation: approx. 7,500 Nm Face plate speed: approx. 2.5 rpm Face plate torque: approx. 1,500 Nm

Condition: excellent (used), Several 150 m³ steel storage tanks (extinguishing water tanks) located underground Volume: 150,000 litres diameter: approx. 3.000 mm length: approx. 22.500 mm Weight: approx. 28,000 kg The tanks are converted to underground extinguishing water tanks according to DIN 14230: The tank has an extinguishing water suction connection according to DIN 14244 with a mounted fire brigade coupling/fixed coupling A according to DIN 14319 in the design form B without gauge connection. Kwedefnh Tgepfx Adwet Furthermore, the tank has a venting flange connection in NW/DN 100 with cap in a total length of approx. 1,300 mm suitable for 800 mm ground cover and 500 mm above ground. - The tank is emptied, cleaned and has been provided with a bitumen exterior coating by us at the factory. - if required, we can provide the tank with a full bitumen-based interior coating (against corrosion) or epoxy resin interior coating A cost-effective delivery with our own truck is possible. Simply inform us of the delivery location, you will then immediately receive the exact freight costs. An inspection is possible at any time by prior appointment. If you need any further information, just give us a call or send us an e-mail to b.barth (a) barth-tank. de