Pneumatic forging hammer, air hammer

SAY-MAK SPH 50

Year of construction: 1940, condition: used, Automatic universal hobbing machine for the production of spur gears worm gears Lsdekw T Rmspfx Ap Aohg Largest milling diameter 120 mm Smallest milling diameter 5 mm Smallest tooth pitch module 0,30 Largest tooth pitch 2 mm largest milling length 100 mm with all accessories

Condition: used, Year of construction: 1998, turning diameter over bed 0400 mm turning diameter over slide rest 260 mm turning length 1500 mm centre height 200 mm centre distance 1500 mm spindle bore 50,8 mm speeds 20- 3150 U/min feeds longitudinal slide 0,01 - 3,24 mm/U Lhsdpfxexp Rzbs Ap Aog feeds cross slide 0,005- 1,62 mm/U weight of the machine ca. 2 t dimensions of the machine ca. 3,35 x 1,4 x 1,9 m voltage 400 V connected load 7,7 kVA With chuck, Multifix toolholder and digital readout.

Year of construction: 2024, condition: new, Motorized guillotine shears Technical data Cutting capacity: 2,5mm Cutting length: 2550mm Cutting angle: 1°40' Stroke rate/min: 35 1/sec. Motor power: 3kW Lodpfx Aehk Nf Rjp Ajhg backgauge range: 550mm table width: 400mm table height: 850mm height: 1260mm width: 1350mm length: 3100mm Weight approx.: 1540kg

Year of construction: 1980, condition: good (used), A used very well preserved cycle controlled lathe from Weisser Heilbronn with SIEMENS control. centre distance 2000 mm centre height 295 mm Swing over bed 600 mm Swing over cross slide 260 mm Swing diameter in the bend 800 mm Total length of the crank 375 mm Bed width 450 mm Plan travel X-axis 350 mm Longitudinal travel Z-axis 1850 mm Spindle nose DIN 55022 size 8 Spindle speed Number 18 14 - 1400 rpm spindle bore 71,5 mm Diameter of front bearing 110 mm feed range 0,01 - 40,95 mm/rev rapid traverse 8 m/min Direct current drive 15 kW 400V 50Hz Max. permissible torque at the spindle 2500 Nm Tailstock quill 80 mm quill stroke 250 mm inner taper quill MK 5 Length x width x height Weight of the machine 5500 kg Accessories Tailstock Pneumatic three-jaw chuck with interchangeable jaws 315mm Quick change holder "MULTIFIX "in front of the center size "C Quadruple turret behind the center Tool holder Coolant device Ledpjgyy I Ajfx Ap Ashg Pneumatic steady rest Technical data and dimensions: Errors excepted. Videoconference via whatsapp possible by appointment

Condition: used, greates pass round over bed 480 mm swing diameter over bed slide 300 mm turning length 1500 mm centre height 240 mm centre distance 1500 mm spindle bore 42 mm Ljdpfotqqx Ajx Ap Ajhg spindle turning speed range 14 - 1400 U/min total power requirement kW weight of the machine ca. 2,4 t dimensions of machine L x W x H 3,00 x 1,05 x 1,40 m Accessories: 3-jaw chuck 250 mmø, MULTIFIX-head, running center

Condition: excellent (used), Year of construction: 1978, functionality: fully functional, machine just arrived and will be cleaned soon. turning diameter over bed: 400mm distance between centers: 1000mm spindle size: 50 mm chuck size 200mm speed range 40 rpm to 2000 rpm machine weight: 1700kg including 3 jaw chuck and tool holder Lhjdpfxsyh Ndwo Ap Aeg

Condition: ready for operation (used), Romanian Forging Hammer CM 2500 (The hammer is similar to Huta Zygmunt MPM 6300B) - Maximum impact energy at full stroke: 7000 kgm - Ram weight: 2500 kg - Mode of operation: pneumatic - Ram stroke: 850 mm - Number of blows per minute: 100 - Working pressure: 5–7 bar - Anvil weight: 48 t - Total weight: 65 t Romanian Forging Hammer CM 1250 (The hammer is similar to Huta Zygmunt MPM 3150B) - Maximum impact energy at full stroke: 3600 kgm - Ram weight: 1250 kg - Mode of operation: pneumatic - Table size (front to back): 700 mm - Stroke: 800 mm - Number of blows per minute: 110 - Working pressure: 5–7 bar Lhjdpfxjw Sdxaj Ap Aog - Max. upper die weight: 400 kg - Die height: 220 mm - Ram (front to back): 500 mm - Air consumption: 15 m³/min - Anvil weight: 24 t - Height of machine above floor: 3750 mm - Total machine height: 4380 mm - Total weight: 35 t

Year of construction: 2023, condition: new, machine/vehicle number: PRJ065955, ALZMETALL bench drill drilling capacity in steel 12mm Drill chuck mounting B16 outer taper, spindle stroke: 40mm, throat: 200mm, column diameter: 50mm, machine table usable support: 300x240mm, with T-slots 2 x 12mm x 80mm, distance spindle-base plate min./max. 110/250, feed by hand, machine height without options: 670mm, net weight: 64 kg. - Speed infinitely variable 250-5000 rpm Standard equipment: 5" TFT - LCD display with touch function: manual input spindle speed setpoint, speed display actual value, integrated drilling depth display with touch zero point acceptance, virtual drilling depth scale in display, machine status indicators and warnings in display, service information, selectable operating language DE/EN/FR/ES/IT/NL/RU. AC motor 230 Volt, 50 Hz, Connector plug ready mounted, Cable length 2m, Three separate buttons for clockwise - anticlockwise - stop, spindle stop by brake function, spindle protection with electrical fuse, main switch lockable, mushroom pushbutton (latching) for EMERGENCY STOP, speed adjustment infinitely variable by means of potentiometer, protection class IP54, spindle protection with electrical fuse, paint finish: DD structure paint signal white RAL 9003, PANTONE 7545c, black incl. the following options: LED machine light pos. 12. Ljdpelub Rdofx Ap Ashg Delivery time: ex stock Waiblingen Beinstein

Year of construction: 2022, condition: new, Motorized guillotine shear MS 1303 Technical data: Sheet width: 1350 mm sheet thickness: 3,0 mm stand width - table width: 400 mm Lodpfx Apohk Nfus Ajhg working height: 850 mm Control: conventional

Condition: used, Year of construction: 1999, x-travel 4000 mm Lodpoxzuz Nsfx Ap Ashg y-travel 1000 mm z-travel 1500 mm Control Heidenhain 355 weight max. 10 t ja more pictures available