Center lathe

Schaublin SA 125 C

Condition: good (used), Year of construction: 1993, functionality: fully functional, Schaublin 102 N - VM, Machine number BL 330699, Year of manufacture approx. 1993, Machine with leadscrew, Centre height 102 mm, Leadscrew: diameter 40 mm, hardened and thread ground. Leadscrew pitch: 4 mm. Feeds: 8 longitudinal feeds from 0.02 to 0.3 mm/rev. Threading range: Metric: 20 pitches from 0.25 to 4 mm. Imperial (inch): 25 pitches from 80 to 6 tpi. Centre distance 450 mm, max. turning diameter over bed 200 mm, max. turning diameter over cross slide 120 mm, Spindle speed up to 2,800 rpm, Tailstock, Bedpozlc Apefx Andjdi Accessories,

Condition: as good as new (ex-display), Year of construction: 2025, functionality: fully functional, ALZMETALL AX 4 / SV pillar drilling machine 3KW Manufacturer: Alzmetall Type: AX 4 / SV Condition: NEW Year of manufacture: 2025 Drilling capacity steel E335 (St 60) 55 mm Thread cutting Steel E335 (St 60) M 42 Cast EN-GJL-200 M 56 Short spindle MK 4 Spindle stroke 140 mm Usable projection 300 mm Column diameter 145 mm Machine table, usable support 615 x 430 mm Distance spindle-table min./max. 150/735 mm T-slots, number x width x distance 2 x 14 x 224 mm Feed 0.1 + 0.3 mm/rev Machine height approx. 1850 mm Net weight approx. 380 kg Drive stepless Motor 1500 rpm Power 3.0 kW Spindle speed rpm 70-2400 Standard equipment: Main switch with motor protection switch, lockable Mushroom push button (latching) for EMERGENCY STOP Speed adjustment stepless Speed display digital Bjdpfx Anoy S Axgododi Feed overload protection Protection class IP 54 Spindle protection with electrical protection Paint: DD structural paint signal white RAL 9003, PANTONE 7545c, black Machine oil: initial filling; Container supplied loose Available options: - LED machine light - Thread cutting device with soft start (from 2025) - Coolant device in the base - Digital drilling depth display - Drilling depth fine adjustment 0.1 mm

Condition: new, We supply and install our own, new, digital PLC controllers suitable for warehouse lifts and paternosters from all major manufacturers on the market. Our LTG StoreControl LL (warehouse lifts) and LTG StoreControl P-Touch (paternoster) controllers thus offer replacements for controllers for which spare parts are no longer available. Our controllers easily connect your dynamic storage systems to higher-level warehouse management systems and implement access restrictions. Bsdpfx Anjqlb Smjdjdi

Condition: excellent (used), functionality: fully functional, Weiler Primus guide and spindle lathe from the training workshop!!! Technical data: >> Year of manufacture approx. 1985 Machine no. 1191 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear stages >> Spindle passage 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm / rev >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 x three-jaw chuck 125 mm with 2 sets of jaws >> Collet device with Collets 18 pieces >> Mulifix size A with 3 steel holders >> Stop >> Electric spindle protection Bdjdpfx Anevtp Edsdei About the machine: A Weiler Primus guide and pull spindle lathe is offered in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs quietly even at high speeds. The Primus was in a training workshop. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site with power on and see for yourself its condition.

Condition: excellent (used), Year of manufacture: 1973 Distance between centers: 500 mm Distance between centers (vertical): 125 mm Swinging diameter over bed: 270 mm Swinging diameter over cross slide: 120 mm Spindle bore: 32 mm Spindle nose: Camlock D1-3 Spindle speed: 225 - 3000 rpm Tailstock quill: MK 2 Weight: approx. 930 kg Dimensions W x D x H: approx. 1473 × 730 × 1280 mm Condition: very good Accessories: see pictures Through hole in the chuck: 28 mm Collet system: Schaublin B32 Automatic feed: 4 - 260 mm/min Bsdpfxozyyn Sj Andjdi Cuttable metric threads: 0.25 to 8 mm Cuttable inch threads: 112 to 3 threads per inch

Condition: excellent (used), functionality: fully functional, Weiler Primus LZ/G lead and feed screw lathe in special paint finish light gray !!! Technical data: Bdodpfxsvivmyj Andoi >> Year of construction ca.1990 Machine-No.3150 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> spindle passage 23 mm >> Short taper spindle head DIN 4 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Switchable spindle brake >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 piece three-jaw chuck NEW 125mm with 2 sets of jaws >> Mulifix size A with 2 steel holders >> collet chuck device new with collets from 3 to 26mm 1 mm increasing new >> To the machine : We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run smoothly and evenly. The bed guides are in very good condition. The Primus was used in a training company. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and see the condition for yourself.

Condition: good (used), Year of construction: 2014, functionality: fully functional, Hurco VM 20 i, Year of manufacture: 2014, Control system: Winmax, Travel range X/Y/Z: 1016/508/400 mm, Tool changer: 24-position, Tool holder: SK 40, Bsdpfezc Icwjx Andodi Spindle speed: up to 12,000 rpm, Chip conveyor, Approximately 11,000 operating hours.

Condition: ready for operation (used), Year of construction: 2014, operating hours: 10,000 h, travel distance X-axis: 1,016 mm, travel distance Y-axis: 508 mm, travel distance Z-axis: 400 mm, spindle speed (max.): 12,000 rpm, number of slots in tool magazine: 24, number of axes: 3, This 3-axis Hurco VM20i was manufactured in 2014. It features an X-axis travel of 1,016 mm, Y-axis travel of 508 mm, and Z-axis travel of 400 mm. The machine includes a table size of 1,170 x 507 mm and a spindle speed of 12,000 rpm. If you are looking to get high-quality machining capabilities, consider the Hurco VM20i vertical machining centre we have for sale. Contact us for further details. Bsdpfxszc If Se Andsdi • Control: WINMAX • Clamping System: SK40 DIN69871 AD/B • Tool Holder: SK40 • Table Size: 1,170 x 507 mm • Spindle Hours: Approx. 10,000 h • Condition: Used • CE Marking: Yes • Frequency: 50 Hz • Voltage: 400 V • Power Supply: 3 Phase • Largest Motor: 13 kVA • Full Load: 20 kVA • Interrupt Capacity: 10,000 A • Short Circuit Current: 22 kA RMS Symmetrical • Maximum Ambient Temperature: 35 °C Technical Specification Through-spindle Coolant No

Condition: excellent (used), Year of construction: 2017, Traverses X Y Z: 1016mm x 508mm x 508mm, table size 1168mm x 508mm, 10000rpm spindle, 20 station ATC, Bdedpfxjzh Hw Ne Andoi BT40 spindle taper, input 15kW, Hurco WINMAX 5 control, coolant, swarf auger.

Condition: excellent (used), Year of construction: 1989, functionality: fully functional, Weiler Praktikant 140 B Lead and Feed Screw Lathe with Toolroom Accuracy featuring NEW K&C 3-Axis Digital Readout! Technical Data: - Year of construction: 1989 Machine No.: 89-140-1471 - Centre height: 140 mm - Centre distance: 650 mm - Spindle speeds: from 24 to 2500 rpm - Spindle bore: 40 mm - Short taper spindle nose DIN 55027 size 5 with bayonet lock - Tailstock MK 3 - Feeds: from 0.02 to 0.63 mm/rev - Thread cutting: Metric, Imperial (inch), Module and Diametral Pitch threads possible - Metric thread pitches: from 0.25 to 8 mm - Weight: approx. 680 kg - Spindle brake, selectable - Dimensions: Length 1.6 m, Height 1.25 m, Depth 0.7 m Accessories and Equipment: - NEW K&C 3-axis digital readout, 12 months manufacturer warranty and operating manual Functions: switch mm/inch, coordinate selection ABS/INC, display value halving, reference point, tool library for 200 tools, taper calculation, radius/diameter indication, quick zeroing, count direction switching - NEW collet system with collets from 3 to 25 mm, 1 mm increments - Three-jaw chuck, 160 mm, with 1 set of jaws - Multifix size A with 2 tool holders - Face plate - Bed stop - Rear cover - Machine feet - Electronic spindle guard Bedsymdymepfx Andsdi - Operating manual Safety features: Electronic spindle protection, lead and feed screw cover, 2 emergency stops, spindle brake, electronic change gear guard About the machine: For sale is a Weiler Praktikant 140 B lead and feed screw lathe in very good condition. This well-maintained lathe comes from a training workshop. All slides operate smoothly and evenly. Even at high spindle speeds, the Weiler runs quietly. This newer generation of Weiler lathes is very user-friendly and allows the production of ground-like surface finishes. Take the opportunity to view and test this machine under power on site to verify its condition for yourself.