Straightener for shafts and pipes

SMS MEER

Year of construction: 2000, condition: excellent (used), SMS MEER CNC DOUBLE SIDED CHAMFERING MACHINE Manufacturer: SMS MEER Type: RFA 14 Yom: 2000 Dedpfoghrguex Afpekh Working range: tube Ø 21,3 – 114,3 mm Wall thickness 2,3 - 11 mm Length: 6-12m Composed of two RFA14 chamfering machines with transport devices between the machines. The task of machines is to chamfer inside and outside both ends of the tubes. The range of diameters of chamfered tubes 21.3-114,3mm and wall thickness of 2.3-11mm in the length range of 6-12m. The task of transport in the area of the chamfering machines is to collect the tubes from the roller table and move them between the chamfering machines.

Condition: used, Year of construction: 1977, pressure 250 t Dksdpfx Ajvuuaijfpsh stroke 40 - 190 mm no. of strokes 40 /min throat 500 mm passage to the back 1050 mm dayligth 615 mm table surface area 1380 x 880 mm hole in the table 450 mm table height over floor 800 mm ram surface 1200 x 800 mm ram adjustment 125 mm power requirement 22,0 kW Weight 24,0 t dimensions of the machine ca. 2,0 x 2,5 x 3,95 m x m x m permitted for manual loading according to the German Safety Regulations (UVV) with motor, pneumatic clutch/brake combination, hydraulic overload protection in ram, pneumatic counterbalance in ram, motoric ram adjustment, manual stroke adjustment, motoric centralized lubrication, bolster plate, two-hand operation

Condition: excellent (used), Year of construction: 2012, section dimension max. 150 x 50 mm pipe Ø 50 – 150 mm wall thickness 1,5 - 5,5 mm reference material (tensile strength) 600 N/mm² coil Ø max. 2.100 mm coil weight max. 10 t finish pipe length max. 9.000 mm round pipe Ø according to list rectangular pipe according to list speed 100 m/min working direction left → right The line consists of: Djdjuc Sw Aspfx Afpekh 1. entry part: double carousel decoiler coil opener/pinch roll unit/leveller crop shear strip tail end welding machine strip guide strip twister/pinch roll unit/strip accumulator entry strip accumulator edge trimming exit twister 2. forming part: No. of horizontal stands: 4 No. of vertical stands: 3 3. welding part (HF) 4. calibrating part 5. separation 6. edge bevelling 7. blowing out 8. bundling 9. hydraulics 10. electrics

Condition: used, Stainless steel welding line MOD.70/120, made OLIMPIA 80 with tricathode welder & Seam bead roller & Orbital polishing Specifications: - Diameter : 35 – 120 mm - Thickness : 0.7 – 3.5 mm - Length : 3 – 6 m Tube diameter: 35 – 120 mm Thickness: 0,7 – 3,5 mm Tube length: 3 – 6 m Djdpfx Asvtn H Tefpokh

Condition: used, Technical details: grinding length: 12000 mm grinding width: 2800 mm workpiece height: 2510 mm max. workpiece weight: 24.000 kg table surface area: 11990 x 2500 mm distance between columns: 2820 mm cross rail adjustment: 2510 mm table feed: 1 - 40 m/min total power requirement: 110 kW weight of the machine ca.: 151 t dimensions of the machine ca.: 32,5 x 9 x 6,73 m .....machine is in top condition for high precision work! with CNC SIEMENS 840 D 1 universal grinding head, 22 kW swivelling of the grinding spindle +/-110° grinding wheel dimension 700 x 130 mm vertical stroke 1000 mm with dressing unit Djdpfx Aowc A Snefpekh 1 surface grinding head, 30 kW grinding wheel dimension 600 x 150 mm vertical stroke 230 mm with dressing unit coolant and filtering unit diverse grinding wheel flanges *

Condition: like new (used), Year of construction: 1991, functionality: fully functional, overall weight: 35,000 kg, pressing force: 250 t, type of input current: three-phase, power: 30 kW (40.79 HP), punching force: 250 t, input voltage: 200 V, Equipment: documentation/manual, safety light barrier, AIDA NC2-250(1) 250t eccentric press in excellent condition /ctA2/ Manufacturer: AIDA Type: NC2-250(1) Push force: 160t Year of manufacture: approx. 1991 Stroke length: 170mm Distance above table: (adjustable) 280-400mm Table size: 2700x760mm Bear size: 2100x700mm Electrical power: 3x200V(!!), 30kW - Japanese standard Net weight: 35000kg Size: 2760x2800x3980mm Automatic greasing system. Automatic cutting oil dosing - RAZIOL EST-02 Optionally with disc winder and straightener. Djdeu Dxb Topfx Afpokh

Year of construction: 2002, condition: reconditioned (used), Beam cutting, drilling and marking line DISC SAW Brand: KALTENBACH Model: HDM 1431 / T13 / SP-CNC Year 2002 Serial number: 122.400 Weight without accessories: 10,980kh - Disc saw with downward cut. - Geared saw unit, drive system and saw blade on wear-resistant swivel bearing. - Heavy saw gear with pinions in oil bath, with inclined teeth, hardened and sharp. - Hydraulic advancement of the saw blade, adjustable according to the table, very fast recoil. - Hydraulic horizontal clamping device. Rear clamping jaw with long-stroke clamping cylinder and automatic recoil limitation. - Vertical clamping block with self-adjusting push plate. - Oblique cutting device to adjust the angle from 45° to the left to 35° to the right. - Material sensor to automatically switch from rapid advance to work advance. - Hydraulically elevating feed roller for optimum material transport on the saw table. - Economical lubrication by means of a micro-dosing installation, especially suitable for sawing profiles. - Chip collector installed on the machine bench. Specs: - Cutting disc housing: 100x4x30x250mm - Cutting disc diameter: 1,430mm - Cutting width: 9.5mm - Cutting speed: 10 to 20m/min. - Saw advance speed: 0-400mm/min. - Fast reverse speed: 2000mm/min. - Total power: 25KW - Working height: 640mm Cutting capacities: 90º cut - Angle steel: 250mm - Steel in U: 400mm - Double T-beam: 600mm - Wide flanged beam: 1008x302mm - Special wing beams: 1000x450mm Cut to degrees: IPBv beam - 75º: 1008x302mm - 60º: 910x302mm - 45º: 716x304mm - 40º: 716x304mm - 35º: 478X307mm IPBs beam - 75º: 1008x402mm - 45º: 524x357mm IPE beam - 45º: 600x220mm DRILLING UNIT Dkodpfxehzbipo Afpeh Brand: Kaltenbach Model: KDX1215 Serial number: 122.401 Work capabilities: - Angular steel (minimum - maximum): 80x65x10mm - 250x250x28mm - Steel in U (minimum - maximum): 80x45mm - 400x110mm - Double T beam (minimum - maximum): 80x46mm - 600x220mm - Wide flanged beam (minimum - maximum): 100x100mm - 1,008x302mm - Extra wide wings beam: 1,200x500mm Drilling units: 3 - Vertical (Y axis) 1 pc. - Horizontal (Z and W axes) 2ud. Drilling diameters: 8 - 40mm RPM: 150 - 1100 Fast forward - Fast reverse: 3,850mm/min. - 8,000mm/min. Drilling spindle feed rate: 0-500mm/min. Fast spindle positioning tool: 15,000mm/min. Automatic tool changer: 5 u. in each drilling unit. 3x5 u. = 15 total Total power: 45KW MARKING UNIT FEEDING: 26 METERS OF ENTRY WITH BEAM FEEDER + 6 SIDE ARMS FOR BEAM ENTRY IN PARALLEL TO THE ROLLER TRACKS 30 METERS OF ROLLER TRACKS WITH OUTPUT + 6 SIDE ARMS 4 SIDE ARM FOR SMALL PIECES THE GREAT MAJORITY OF ROLLERS ARE MOTORIZED It occupies approximately 60 linear meters between input and output power. *Request machine installation plans.

Condition: good (used), Year of construction: 2002, Universal Machining Center Machine type: DMG DMU 200 P Control: Heidenhain TNC 430 M Year of manufacture: 2002 TECHNICAL DATA: Travel paths: X-axis: 1,800 mm Y-axis: 2,000 mm Z-axis: 1,100 mm B-axis: 0.001° C-axis: 0.001° Number of controlled axes: 5 Speed range: 10,000 rpm Drive power: 44 kW Tool holder: SK 50 Tool changer Tool stations: 60 NC rotary table Table size: 1,700 x 1,400 mm Max. table load: 5,000 kg Dedpfxexuqn Sj Afpokh Equipment features: Chip conveyor Internal coolant supply (IKZ): 40 bar Paper band filter Measuring probe Electronic handwheel

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2023, product width (max.): 1,250 mm, working width: 1,250 mm, conveyor belt width: 1,250 mm, product height (max.): 1 mm, 2 Forstner decoiling towers each 2 coils 1250mm x 2 tons (in total 4 coils each 2 tons) Very well maintained, almoast brand new. Year of manufacture 2023. Dodowqc I Sspfx Afpjkh For more information make a inquiry.

Condition: excellent (used), functionality: fully functional, turning diameter: 1,000 mm, turning length: 8,000 mm, total length: 10,500 mm, A used lathe from the Italian manufacturer Leopolod Pontiggia, model NH 500, is for sale. Technical specifications: Turning diameter over bed: 1,000 mm Turning length: 8,000 mm Extensive equipment as in the photos: 1 x 3-jaw chuck Dkjdpfjv Epigsx Afpeh 1 x 4-jaw chuck 1 x steady rest + various adapters