Straightening press

Stierli-Bieger 2000 RP - 200 to Biege- und Richtpresse

Condition: as good as new (ex-display), ►►► FRONIUS TPS 3200 SET OFFER ✅ Scope of delivery: ➤ Fronius TPS 3200 Power Source (320A TRANS PULS SYNERGIC) ➤ Fronius FK 4000 FC Cooling Unit – Standard features include Flow Control, Thermocontrol, and coolant filter. The cooling unit shuts off if the water cooling fails or gets too hot, to protect the torch package. These functions cost approximately €400 extra from Fronius. ➤ Fronius VR 7000 Wire Feed Case – Compact and practical – in our experience, the most useful wire feed case – the wire is securely stored in the closed case. ➤ Fronius Intermediate Hose Package, long version – each machine is supplied with a 5-meter-long connection hose between the power source and the wire feed case for greater flexibility and improved handling. Take the wire feed case off the machine to access hard-to-reach areas! The connecting hose is neatly stored on a hook on the side of the machine. (Hooks are produced by us) ➤ Fronius Large Trolley – Probably the best trolley with a gas bottle holder on the market. ➤ Binzel Torch Package – With up/down amperage control on the torch. ➤ Ground cable 3-4m ➤ New Messer pressure regulator ➤ New basket reel adapter for large wire spools With this machine, almost all materials can be welded, including aluminum, steel, and stainless steel (V2A). It features pulse wire programs and is also suitable for MIG brazing (CuSi), commonly used in the sheet metal industry. Additional options are available at extra charge For example: Fronius Aw4000/Aw5000 Job Master Torch Package (with display on torch) + EUR 550.00 ----- Iedpfxewbil So An Dsar IMMEDIATELY AVAILABLE PROPER INVOICE Inspection is possible in Austria, Vienna 1230! ✔ Insured shipping on a pallet is no problem! ✔ We are also available via WhatsApp and Viber. ✅Questions✅Questions✅Questions✅Questions: ✅Questions✅Questions✅Questions✅ ►►► What is the condition of the equipment? For clarification: we purchase nearly new used equipment, disassemble and thoroughly inspect everything, replace wear parts as necessary, and only after a successful test weld do we release the equipment for sale. "All" machines are clean with no burn marks on the displays and without numerous burn holes or dents! With us, you buy an item that is ⭐in excellent condition and doesn’t look worn out! ►►► Do we receive an invoice when purchasing from you? Yes, you will receive a proper invoice from us. If you have a valid VAT ID and meet the requirements for intra-community delivery within the EU, we can issue a net invoice. ►►► What payment options are available? Prepayment or cash on personal collection. ►►► Why buy from us? We are experts in this series of Fronius welding machines and always have 60-80 units in stock – exclusively Fronius, no other brands! We know these machines inside out and do not sell anything we don’t have expertise in.

Condition: excellent (used), Year of construction: 2007, operating hours: 53,000 h, functionality: fully functional, machine/vehicle number: 206432, clamping force: 2,000 kN, screw diameter: 50 mm, clearance between the columns: 570 mm, displacement volume: 392 cm³, injection pressure: 2,000 bar, ejector stroke: 225 mm, overall weight: 7,450 kg, Equipment: documentation/manual, Here we, as a dealer in injection moulding machines, are offering the following well-maintained used injection moulding machine: Of course, we also purchase well-maintained injection moulding machines manufactured from 2010 onwards. We have been a wholesaler of used injection moulding machines for over 25 years. Current note – Tax notice and advantage for used machines: As of 01.07.2025, used machines will also be eligible for a special depreciation of 30% annually for tax purposes. Manufacturer: Arburg Model: 520C 2000-800 GE Serial number: 206432 Year of manufacture: 2007 Operating hours: approx. 53,000 Control system: Selogica Dimensions (L/W/H): 5.53 x 1.80 x 2.20 m Weight: 7,450 kg Functional condition: Fully operational Condition: Very well-maintained – German origin Extras: - Thermoplastic cylinder complete, 50 mm, highly wear-resistant - Screw in HC version instead of standard - Selogica direct control - Hydraulic system with 2 variable-displacement pumps - Anniversary model GOLDEN EDITION - Thermoplastic processing - Open nozzle 50 mm - Nozzle tip 50 mm extended - Heating band for open nozzle Iodpfxsw Tt R Ie An Dear - Heating band for extended nozzle tip - Central clamping platen set 570, center Ø 125 mm - 2-piece air blast device with pressure regulator - Air blast device connection 1 - Selector unit connection - Core puller 1 for serial motion holding pressure via check valve - Conveyor belt connection via 5-pin socket - Robot interface (per EUROMAP 67), 50-pin - ARBURG host computer interface - Additional socket distributor: 1x CEE, 1x Schuko - Serial printer interface USB - CompactFlash interface for data set storage - Operation authorization with chip card per EUROMAP 65 - 1 additional heating control circuit for nozzle or adapter with socket - Dosing unit interface - Free cooling circuits, manually adjustable - Machine-specific cooling circuits controlled - Extended monitoring package - Extended motion package - Production control package - Optimization / operator assistance package - Quality assurance package - Documentation package Complete documentation included. Injection unit: Screw diameter: 50 mm Shot weight: 359 g/PS Injection pressure: 2000 bar Shot volume: 392 cm³ Clamping unit: Clamping force: 200 t / 2000 kN Tie bar spacing: 570 x 570 mm Mounting plates: 795 x 795 mm Mould installation height: 300 mm Max. platen distance: 950 mm Opening stroke: 650 mm Ejector stroke / force: 225 mm / 66 kN Clamping unit: hydraulic Motor power: 22 kW Heating power: 19.9 kW / 8 heating zones Total connected load: 45 kW The machine is available for immediate delivery at our warehouse in Hannover, Germany and has been tested. Warranty: Warranty until initial commissioning. Loading/shipping: Free loading onto the buyer's truck or free delivery within Germany (freight charge applies) Available from our warehouse in Hannover, Germany. For your information regarding our machines and company: - We sell only our own machines purchased from ongoing production at our Hannover warehouse. - All listed machines are inspected and tested prior to removal. - We do NOT sell insolvency assets – we are NOT brokers handling third party property. - All offered machines come from successful businesses where proper maintenance is standard practice. - All machines offered are available for viewing at our warehouse.

Condition: used, Used 3D Printer EOSINT M 270 low operating hours (4910) Ijdpfjwd Ulvex An Dear

Condition: new, Year of construction: 2023, functionality: fully functional, type of input current: three-phase, travel distance X-axis: 1,500 mm, travel distance Y-axis: 750 mm, travel distance Z-axis: 610 mm, workpiece weight (max.): 1,500 kg, total height: 24,920 mm, total length: 43,670 mm, total width: 30,700 mm, table length: 1,600 mm, table width: 700 mm, spindle motor power: 11 W, rapid traverse Z-axis: 24 m/min, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 30 m/min, spindle nose: Iso 40, spindle speed (max.): 8,000 rpm, spindle speed (min.): 40 rpm, tool diameter: 75 mm, tool length: 250 mm, Equipment: documentation/manual, rotational speed infinitely variable, NEW vertical machining center "AWEA BM-1500 II" with FANUC 0i-MF Plus CNC Accessories present: 4th axis interface Iasdpjrkn Iiefx An Djr Air blow system Left side auger chip conveyors Coolant through spindle ( CTS ) at 20 bar Coolant gun Fairing bottom washing system 500 liter refrigerant collection tank Automatic power-off system Alarm light & work light

Condition: used, 3-axle truck trailer, low-loader trailer MÜLLER MITTELTAL Type AZP Curtain-sided low loader, low-loader trailer, low loader for machine transport First registration: 2001 Total mileage: approx. 350,000 km Gross vehicle weight: 24,000 kg Unladen weight: 5,500 kg Payload: 18,500 kg Isdpfx Aot N Anten Djar Platform height: 840 mm Loading height under tarpaulin frame: 3,200 mm Platform length: 7,450 mm Overall length: 9,150 mm Overall width: 2,550 mm Overall height: approx. 4,050 mm Axle load front: 8,000 kg Axle load middle: 8,000 kg Axle load rear: 8,000 kg Tyres: Michelin 215 / 75 R17.5 (135/133J XTE 2+ TL) - Rear wing doors at drop side height - Tarpaulin frame with EDSCHA roof system - Tarpaulin frame designed for easy removal (can also be used with the frame removed and the tarp pushed forward) - Spare wheel mounted on the front wall - Independent lifting and lowering of front and rear axles - Middle axle with lift function - Drawbar – extendable in multiple stages - Heavy-duty lashing rings on the outer frame and in the vehicle centre - ALU drive-on ramps, length 268 cm, width 410 mm, height 130 mm (surcharge EUR 2,000 net) The trailer was purchased new by us and is therefore first-hand. The trailer has been deregistered since 2025.

Condition: used, Year of construction: 2006, Technical details: x-travel: 800 mm y-travel: 800 mm z-travel: 800 mm turning speeds: 12.000 1/min tool taper: SK 50 control: SIEMENS 840D shopmill tool change unit: 240 fach size of pallet: 630 x 630mm mm spindle: 52 kW / 430Nm total power requirement: 87 kVA weight of the machine ca.: 15 t horizontal machining center, NC-round-table pallet-changer (2 pallets), Internal Coolant Supply 40 bar, prepared for Infrared Touch Probe Renishaw MP 10 without probe, tool-breakage control (mech.), MQL, airblast through spindle, oilmist suction, TRANSMIT funbction, accuracy package, mode 4, glass window right door, incl. FASTEMS FPC 1000 pallet pool for 14 pallets, incl. setting up station, control, and 10 pallets Iaedpfx Anopumdcs Djr approx. 98.500 h main switch on apprax. 45.500 Spindle hours *

Condition: good (used), Year of construction: 1962, High speed radial drilling machine, radial drilling machine, drilling machine, boom drilling machine, high speed radial drilling machine -Clamping table: 400 x 1100 mm -Projection: 930 mm -Taper mount: MK4 -Engine power: 1.35/1.8 kW -Speed: 41-1700 rpm -Columns: Ø 200 mm Ijdpfx Asirax Uen Doar -Spindle stroke: 125 mm -Thread cutting device: YES -Feed: 0.075 - 0.3 mm/rev -Dimensions: 1800/1235/H2240 mm -Weight: 1500kg

Condition: used, TECHNICAL DETAILS - Number of axes : 4 MILLING SPINDLE - Tool holder type : BT40 BIG PLUS - Spindle power : 26 [kW] - Spindle speeds : 15000 [rpm] LINEAR AXES - Travels on X/Y/Z axes : 560/640/640 [mm] - Rapid traverses rates (X/Y/Z) : 60 [m/min] B ROTARY AXIS - Travel : 360 [°] - Indexing precision : 0.001 [°] TOOL CHANGER - Auto. Tool Changer type : Bras chargeur - Tool magazine capacity : 60 PALLET CHANGER - Pallet changing device type : Rotopalette - Pallet size : 400X400 [mm] - Pallets number : 2 - Maximum weight upon pallet : 400 [kg] - Maximum workpiece diameter : 630 [mm] - Maximum workpiece height : 900 [mm] POWER SUPPLY - Supply voltage : 400 [V] WEIGHT & DIMENSIONS - Machine floor space : 4100X2300 [mm] - Machine height : 2720 [mm] - Machine weight : 11000 [kg] MACHINE HOURS - Number of working hours : 3700 [h] EQUIPMENT - CNC : Fanuc 31 iB Interface : Ethernet / RS232 / USB / PCMCIA - Electronic handwheel - Linear scales - Rigid tapping - 3 colors status lamp - Coolant tank * with high-pressure pump : 25 [bars] * Coolant through spindle * With cabin washing Iodpjuhbv Sjfx An Doar - Chips conveyor : Arrière - Spindle cooling unit - Tool probe - Workpiece probe : Renishaw OMP60

Condition: new, Year of construction: 2024, cutting height (max.): 150 mm, cutting range round steel at 45°: 108 mm, cutting range round steel at 90°: 108 mm, BERG+SCHMID GBS 218 Eco AutoCut double mitre bandsaw Speed: 25-80 m/min - Mitre left 60° - For cutting steel, stainless steel and aluminum profiles - Quick-clamping vice with quick-clamping device a. - Built-in blade tension control b. - Saw blade guide made of carbide c. - Electric automatic cooling system - Machine base (supplied disassembled) The AutoCut system consists of: - Hydraulic cylinder, feed control, spring assembly, limit switch and enables three work sequences: 1. automatic lowering of the saw frame via hydraulic cylinder with infinitely adjustable feed control valve and limit switch at the end of the cut 2. high-speed lowering of the saw frame from the rest position up to the workpiece, then switching to normal saw feed 3. manual operation - hydraulic cylinder works as a brake cylinder Saw blade dimensions: 2455x27x0.9mm Further accessories such as saw bands, roller conveyors, measuring stops, minimum quantity lubrication etc. available on request! Isdpfx Ajt I R Edjn Djar Delivery time: ex stock Waiblingen Beinstein

Year of construction: 2020, condition: new, Transport systems Depending on the customer's requirements, transport systems can move on the floor or be suspended on poles. - For comfortable solutions for manual installations, we recommend suspended cross traverses (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at once and have e.g. several cabins with different colors, flexible solutions with the use of the power-and-free conveyor are used. This is the most expensive solution. All installations are made to measure, depending on the customer's requirements. Continuous suspended chain transport systems are designed and manufactured to individual customer orders. In this system, it is also possible to make bottom conveyor systems on which details are placed, e.g. flower pots, rims (photo). ROMER also manufactures suspended transport systems. Iaodjfz U S Espfx An Dor Crossbeams (cross transports) are designed and made for the needs of specific installations The use of one photocell The use of one photocell in the space of the detail allows you to measure its length and, consequently, gives the option of switching on the guns when the detail appears in their range, and switching off the guns immediately after painting the detail. The photocell is standard equipment. Identification of details by means of special markers. Above the sling there are plates with identification holes. Based on them, the PLC controller in conjunction with the photocell recognizes the painted detail, turns the guns on and off in good time - thus saving energy and powder paint. Vertical shape detection. The use of light gates with horizontal detectors allows the PLC controller to analyze the shape of a detail vertically. The PLC controller counts the time in which the detail should appear in the gun space - thanks to this it is possible to selectively turn the guns on or off. Using light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of workpiece dimensions, thanks to which it is also possible to control manipulators.