Center lathe

tour WALDRICH SIEGEN 44 TP 95

Condition: good (used), Year of construction: 1995, functionality: fully functional, turning diameter over cross slide: 267 mm, spindle bore: 76 mm, center height: 228 mm, center width: 1,500 mm, quill stroke: 229 mm, quill diameter: 75 mm, total length: 3,030 mm, total width: 1,200 mm, total height: 2,000 mm, rotational speed (max.): 1,600 rpm, rotational speed (min.): 20 rpm, overall weight: 2,300 kg, Conventional lathe, center high 228 mm, between centers 1500 mm, bore Ø 76 mm, 16 speed 20 - 1600 rpm, motor 9,3 kw, camlock 8'', dimensions 310x120x200 cm, weight ca. 2300 kgs; equipement: pneumatic chuck SCHUNK ROTA Ø 315 mm, coolant device, 3-jaws chuck Ø 315 mm, several jaws, live center, tool post PARAT WD with toolholders, steady rest, drilling chuck, lamp, manual, cabinet Gusdpfx Akeypud Uoaog

Condition: good (used), Year of construction: 1980, turning diameter over bed slide: 1,040 mm, turning diameter over top slide: 710 mm, turning length: 2,000 mm, bed width: 600 mm, Optional chuck 1200 mm 2 Axis RSF Digital read out Conical turning attachment Spindle bore 130 mm Central lubrication DBC Turning Length: 2000mm Swing over bed Ø: 1040mm Swing over cross slide Ø:710mm Swing in the gap Ø: 1780mm Gap length: 1000mm Spindle bore: 130mm Bed width: 600mm Tailstock spindle Ø: 130Ø Stroke pinole: 300mm Spindle taper: 6Mk Power: 22kW Speeds / ranges: 600Rpm Feed rate X-Axis: 4000mm/min. Feed rate Z-Axis: 4000mm/min. Length: 6000mm Width: 2100mm Guodjx Tgr Tepfx Akaeg Height: 2100mm Weight: 8300kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Craven 2000mm x 8000mm Heavy Duty Lathe 2000mm swing over bed 1500mm swing over saddle 8,000mm between centres Main drive 60kW, 40 ton load capacity Spindle speeds 2 – 152 rpm Steadies 2000mm Bed extension Gedpfx Akox Hp Iwjaeug

Condition: used, Year of construction: 1973, pressure 200 t chamfer lenght 3600 mm distance between columns 2650 mm dayligth 500 mm throat 300 mm stroke 250 mm working feed 10,5 mm/sec return speed 100 mm/sec ram stroke speed 150 mm/sec table height 900 mm oil volume 500 l total power requirement 37 kW weight of the machine ca. 17800 kg dimensions of the machine ca. 3710 x 1800 x 3390 mm Equipment: - Controlled axes Y1 + Y2 - Manual X-axis with digital position display - Set of upper and lower tools - 2x stop fingers Guodpet I D U Esfx Akaeg - 2x front support arms - Hand and foot controls - Side + rear safety guard - Operating instructions

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR Gsdpjrgzv Nofx Akaoug * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: ready for operation (used), Gear shaping machine STANKO 5M150 Max. diameter of gears that can be cut: 800 mm Max. module: 12 mm Max. cutter stroke: 200 mm Saddle indexing gear diameter: 360 mm Distance between axes (tool and table): 0-700 mm Largest tool diameter: 200 mm Cutter arbor diameter: 44.443 mm Taper: M5 Table diameter: 800 mm Godpfx Aksqcvkveajug Distance from floor to table: 870 mm Indexing gear diameter: 762 mm Table hole diameter: 120A mm Double stroke per minute (s.p.m.): 33-188 mm Range of table feed rates per cutter double stroke: -Circular: 0.2-1.5 mm -Radial: 1-5.4 mm Table rapid rotation speed: 1.7 rpm Table rapid travel speed: 137 mm/min Cutter rapid rotation speed: 3 rpm Main electric motor power: 4.8; 5.7; 7.5 kW Dimensions: 3100x1800x3500 mm Weight: 10200 kg

Year of construction: 1981, condition: excellent (used), faceplate diam 1300mm Guodpfjk Dz N Iox Akaeg max turning diam 1100mm range of turning diam 460-1250mm

Condition: used, Year of construction: 2013, functionality: fully functional, travel distance X-axis: 17,000 mm, travel distance Y-axis: 4,800 mm, travel distance Z-axis: 1,500 mm, table length: 16,000 mm, table width: 3,000 mm, spindle speed (max.): 3,000 rpm, rapid traverse X-axis: 12 m/min, rapid traverse Y-axis: 8 m/min, rapid traverse Z-axis: 8 m/min, distance between stands: 3,800 mm, type of input current: three-phase, position of the milling head: vertikal / Winkelkopf, rotational speed (max.): 3,000 rpm, distance table to spindle center: 2,300 mm, overall weight: 90,000 kg, spindle nose: ISO 60 / ISO 50 Adapter, spindle motor power: 60,000 W, Equipment: rotational speed infinitely variable, ➡️ WALDRICH COBURG CNC GANTRY MILLING MACHINE ⬅️ Heavy Duty Machining | Siemens 840D Retrofit | Ready for Production High-quality CNC gantry milling machine manufactured by Waldrich Coburg available for sale in very good condition. ✔ Machine under power ✔ Inspection & test run possible ✔ Siemens 840D retrofit (2013) ✔ New electrical system & cabinets ✔ New motors & drives ✔ Heidenhain glass scales on all axes ✔ Ideal for large part machining & heavy-duty applications Technical Data X travel: 17,000 mm Y travel: 4,800 mm Z travel: 1,500 mm Floor plates: 16,000 x 3,000 mm Distance between columns: 3,800 mm Distance table to spindle face: 2,300 mm Spindle power: 60 kW Spindle speed: 0.4 – 3,000 rpm Guedpfsy Rrb Iox Akaog Tool taper: ISO 60 / ISO 50 adapter Machine weight: approx. 90,000 kg Equipment Siemens 840D CNC control 2-step gearbox Right angle head WFU 250 with automatic indexing Right angle head WFU 500 with automatic indexing Rapid tapping Tool trolley with tool holders Steel way covers on X/Y axes 2 chip conveyors Perfect for: Heavy machining Machine building Energy industry Shipbuilding Steel & rolling mill industry Subcontract manufacturing 📍 Location: USA 🌍 Worldwide shipping can be arranged 📞 Please contact us for more information, videos, or inspection appointments.

Condition: used, Year of construction: 2010, operating hours: 11,780 h, Equipment: ABS, all wheel drive, Volvo EXCAVATOR EW140C air conditioning 16,850 kg 91 kW Guodpsyltr Asfx Akaeg Top condition

Condition: good (used), Year of construction: 2012, Vertical CNC turning machine with a 12-position turret and powered tools; Year of manufacture 2012, in good condition; Fanuc 31i control system with Manual Guide i; 630 chuck – 900 mm turning diameter; Automatic door; 2-stage gearbox – resulting in very high torque; Tool setter, detachable; Chip conveyor; Various tool holders, fixed and powered; Only approximately 4,100 operating hours. Godeztqp Hepfx Akasug An inspection is possible and recommended by arrangement, with the machine powered on.