Pipe Notcher

TUGRA TT 90

Condition: new, Year of construction: 2025, - Capacity 17-90 mm - With 10 rollers - Angle adjustment Dedpfxelwq R Ss Anqjci - Documentation - 400V

Condition: used, Year of construction: 1970, machine/vehicle number: 120895, pressure:63 t throat:250 mm stroke:8 - 100 mm no. of strokes:120 Hub/min table::715 x 500 mm dayligth:330 mm ram adjustment:63 mm clamping plate:700 x 480 mm hole in the table:240 mm Hole in clamping plate:110 mm dimension of ram:450 x 280 mm weight of the machine ca.:5,5 t dimensions of the machine ca.:1,2 x 1,7 x 2,7 m Dcedpfxefx Hv Hj Anqsi hydraulic tilting single column eccentric press, tilting in 4 steps, opening to rear (325 x 500mm) and below (360x160mm) with central lubrication via hand pump, additional clamping plate 700 x 480 x 850 mm, two-hand operation, foot-trip operation possible, operating-mode selector for adjustment of continuous or single stroke, emergency cut-off, piece counter, various accessories

Condition: used, Year of construction: 2024, tube diameter 16.0 - 90.0 mm width of the strips 100 mm band length 1250 mm grinding band dimension 100 x 1250 mm total power requirement 2.2 kW weight of the machine ca. 180 kg. range L-W-H 1200 x 600 x 1150 mm The TUGRA TT 90 is a grinding machine for grinding pipe and profile ends on the front. Equipment: - electro-motor grinding machine for pipe and profile ends - 10x grinding rollers included in delivery Dedpfx Ansxab Dnsqsci * incl. storage area - rear of the machine - easy manual clamping/opening of the material - lateral adjustment of the material clamping system - grinding up to 50° degrees possible - machine base - collecting tray for easy emptying of grinding dust - EMERGENCY OFF button at the front - front privacy screen made of plexiglass - side transport bags for easy transport

Year of construction: 2001, condition: like new (used), Double-aggregate grinder, two lower aggregates 2 x7.5 kW main power, 4 kW feed, lifting and lowering 2 kW, the machine after renovation, conveyor belt in very good condition. New graphite shoe. The machine has two aggregates from the bottom, contact rollers rubber first shaft second Combi system with graphite runner. Working width 630 mm. Two feed speeds slower faster. Length of grinding belt 1900 mm. Pneumatic oscillation. Tensioning the belts pneumatically. Speed of grinding belt 18 m / s. grinding shoes 1. Declaration of conformity CE power 21 kW nominal whole. Machining height 160 mm. Maszyan has two lower working shafts. Transport tape top system. Djdpfx Aofxpbmenqeci

Condition: used, Year of construction: 2014, total length: 1,500 mm, total width: 1,150 mm, total height: 2,400 mm, Weight: 3.600 kg - Year: 2014 - Documentation available: Yes - CE marking present: Yes - CE certificate present: No - Serial number: 441 - Power [kW]: 3.0 - Press force [ton]: 28 - Max. working width [mm]: 1000 - Column gap [mm]: 950 Dcjdexapftspfx Anqji - Throat depth [mm]: 220 - Backgauge depth [mm]: 415 - Transport dimensions: 1500mm x 1150mm x 2400mm (l x w x h) - Transport weight [kg]: 3600kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 2003, Technical details: bore capacity in steel (diameter): 25 mm throat: 255 mm bore stroke: 140 mm spindle taper MT: MK 3 spindle speed:: 105 - 2980 / 8step U/min Distance spindle/table max.: min.: 350 / max.: 950 mm table clamping surface:: 420 x 270 mm table rotating: 360 ° table swivable approx.: 30° links / rechts drill table adjustment: 600 manuell mm column diameter: 100 mm Dsdpfeu Idhysx Anqsci current- max.: 400 V / 50 Hz A total power requirement: 0,9 kW weight of the machine ca.: 180 kg dimension machine xH: 0,6 x 0,5 x 1,8 m Equipment: Röhm quick-action chuck 3 - 16mm Switchover for clockwise/anticlockwise rotation for thread cutting *

Condition: new, Fastech 3-Roll Round Bending Machine FRM 1250 x 90 Technical Specifications: Special equipment included in the price: hardened rollers motorized rear roller adjustment digital display Sheet metal width 1250 mm Sheet metal thickness 3.0 mm max. Sheet metal thickness 2.5 mm for pre-bending Roller length 1250 mm Roller diameter 90 mm Smallest bending diameter 130 mm Weight 500 kg Dimensions L-W-H 1950 x 900 x 1130 mm Motor: 1.1 kW Equipment: Top and bottom rollers, electrically driven Top roller can be swung out Taper bending device asymmetrical roller arrangement self-braking main motor separate control and operating panel Dedpfx Ajhzq Dqenqsci safety cable Values apply to St-37 / 240 N/mm² CE marking

Year of construction: 2008, condition: good (used), machine/vehicle number: 431808, Lg.No. 18177 Hydr .flat profile and bar shear with notching device and hole punching machine Technical data: - Flat steel shear cuts up to 375 x 10 mm - 220 x 20 mm - section steel shears - cuts L-steel at 90° up to 130 x 13 mm - steel bar shears - cuts round steel up to 45 mm - square steel up to 45 mm - notching device - with square notcher 100 x 42 x 10 mm Djdpfx Anomidyioqeci - punching machine - punching force 600 KN - with stop table - throat 300 mm - punching in steel up to 28 mm Ø in 15 mm - or 34 mm Ø in 12 mm - manual length stop - drive 400 V / 4 kW - space requirement approx. W 600 x H 1550 x D 1500 mm - weight approx. 1300 kg

Condition: as good as new (ex-display), Year of construction: 2026, sheet width 1550 mm plate thickness 6.5 mm pre-bending 4.5 mm diameter of upper rolls 150 mm side roll diameter 130 mm diameter of lower rolls 150 mm distance max. OW zu UW 20,0 mm total power requirement 2.2 + 1.5 kW weight of the machine ca. 2370 kg. range L-W-H 3300 x 1150 x 1110 mm Exhibition machine - NEW not yet in use (!!) Special price on request Equipment: Dedpfxoxabkbs Anqeci - electro-hydraulic 4-roller round bending machine * with driven top roller + bottom roller * stable welded construction - Area of application: * light to heavy sheet metal processing (steel/aluminum/stainless steel) - electro-hydraulic adjustment of the bottom + side rollers - linear guidance of the side rollers - top roller driven by robust electric motor + planetary gear - freely movable, separate control panel - hardened rollers SAE 1050 (CK 45) + crowning - conical bending device - 3x axis digital display for precise roller positions - electro-hydraulic folding bearing - operating instructions (PDF)

Condition: like new (used), functionality: fully functional, Year of construction: 2024, control type: NC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: SIEMENS, controller model: PLC, number of rollers: 4, roller (bottom) diameter: 150 mm, roller (top) diameter: 150 mm, side roll diameter: 140 mm, roller diameter: 150 mm, roller length: 2,050 mm, working width: 2,000 mm, roller height adjustment: 18 mm, working height: 800 mm, sheet thickness (max.): 6 mm, sheet thickness steel (max.): 6 mm, sheet thickness stainless steel (max.): 4 mm, sheet thickness aluminum (max.): 6 mm, sheet thickness brass (max.): 6 mm, sheet thickness copper (max.): 6 mm, overall weight: 2,800 kg, total length: 3,800 mm, total width: 1,200 mm, total height: 1,100 mm, power: 3 kW (4.08 HP), input voltage: 400 V, input frequency: 50 Hz, number of digital displays: 4, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, 4 ROLL BENDING MACHINE NC HYDRAULIC MODEL 2000X6 MM / 4 MM PREBEND PROGRAMMABLE AUTOMATIC ROLLING NC 4 AXIS CONTROLLER Capacity: plate width 2000 mm thickness rolling 6 mm pre-bending 4 mm Dcsdpfx Asw Hpzwenqji minimum diameter of rolling D= 180 mm depending on the plate thickness and strength Rollers length 2050 mm Upper roll size 150 mm Lower roll size 150 mm Rollers hardened surface high strength smooth surface finishing suitable for rolling stainless steel quality plates Conical plate rolling attachment Rotation electric powered on central rollers for bending traction of the plate Pre-pinch load variable upon plate thickness and strength Console electric commands push buttons with digital readout of the 4 rollers on the screen. NC programmable 4-axis to set automatic rolling with save 200 programs in memory front side hydraulic opening to remove the rolled shells speed slow/fast variable safety installation with emergency stop. Instruction manuals for operation and service. Layout mm 3800x1200xH1100 mm Weight 2800 Kgs