CNC ROBOTIC COPING LINE

VOORTMAN V808

Condition: excellent (used), Year of construction: 2012, Operating range V808 Min. / max. height 10 – 500 mm1 Min. / max. width 60 – 1.250 mm Max. positioning weight 13.200 kg Min. material length 1.200 mm Max. cutting width at the bottom 800 mm (only plasma marking and cutting) Plasma cutting unit* Hypertherm HPR260XD Virtually dross-free cutting max. 32 mm Marking lines Yes, marking and cutting with the same consumables Plasma gas mild steel O2 (99,9% pure clean, dry, oil-free) Shield gas mild steel O2/air (99,9% pure clean, dry, oil-free) Cutting speed 12 mm Approx. 3850 mm/min., 260A Cutting speed 20 mm Approx. 2170 mm/min., 260A Cutting speed 32 mm Approx. 1135 mm/min.; 260 A Fuse Additional 75 A slow is required Plasma Gas O2 (99,9% pure clean, dry, oil-free) Consumption 80l/min System pressure 10 bar * grounding, max. 6m of machine: AC power, PE, and service grounds must be connected to all equipment according to Rodpfx Aszcfpzobhew local and national codes. Oxy-Fuel cutting unit Gas supply Magnetic valve with back-fire protection Ignition Automatically Gas Acetylene Consumption 20l/ min System pressure 2 bar Cutting Gas O2 Consumption 450l/ min System pressure 10 bar Operational direction From right to left Profiles 1 Flat steel Angles European standard channels (UNP) European I-beams (IPE) European standard beams (IPN) European wide flange beams (HE) British universal beams (UB) British universal columns (UC) Square tubes 1 Small profiles have to be sufficient straight. General Voltage Stabilizer Not included Ambient temperature 0 - 35°C max. 95% relative humidity Working height 760 mm (+/- 25 mm)

Year of construction: 2013, condition: good (used),  Plasma cutting and extraction table, dimensions 2.500 x 6.000 mm.  Gantry bridge.  Carriage with servo-drives (to position the gantry bridge in X-direction).  Machine track, length 8 m.  HEB450 profiles for the foundation of the machine track, 8 m. Rsdjtp Dhpopfx Abhsw  Plasma cutting unit Hypertherm HPR 400XD, 1 pcs.  Plasma bevel cutting unit, including automatic height control system.  Fume extraction unit Filtercube 4H for plasma cutting unit.  Oxy-fuel cutting torch, 3 pcs.  Automatic height control system IHT M4000 CAP for oxy-fuel cutting unit, 3 pcs.  Torch suspension for oxy-fuel torch (motor driven).  Torch suspension Single Drive for oxy-fuel torch, 2 pcs (automatic torch positioning).  Laser pointer (to align and position the torch).  Computer control system (consisting of an industrial PC and a control panel).  Control software 'VACAM Machine Edition' (including VaCad and VaNest software and online support).  Automatic nesting software Sigmanest "Powerpack" (including 3 days of training for max. 3 persons at Voortman Holland (excluding travel costs and board and lodging) and 1 day online-support).  Emergency stop with stop cord.  Year of build: 2013.

Condition: good (used), Year of construction: 2014, functionality: fully functional, machine/vehicle number: 11383, type of input current: three-phase, working range: 3,000 mm, overall weight: 17,000 kg, input voltage: 400 V, cutting speed: 2,000 mm/min, total width: 4,500 mm, total height: 5,500 mm, total length: 22,400 mm, track width: 1,400 mm, repeat accuracy: 1 mm, workpiece weight (max.): 30,000 kg, warranty duration: 6 months, input frequency: 50 Hz, open-circuit voltage: 400 V, ambient temperature (max.): 45 °C, Secondhand SPC3000 - HGG Profiling Equipment B.V. Are you ready to automate your workflow, but not ready for a heavy investment in pipe cutting machinery? We have an interesting opportunity for you. This 2014 SPC3000 (40 Ton) pipe cutting machine is highly versatile. The machine is capable of cutting pipes from 300mm - 3000mm diameter and is equipped with a lot of extra features: - 4x 10 Ton pipe trolleys (300-2500 mm OD) (1 of them is a driven pipe trolley) - 2x 20 Ton pipe support (2500-3000 mm OD) - Plasma marking system Kjellberg Finemarker - Punch marking system - Can handle 18 meter long pipes Redpfx Absri Slmohjw - Plasma cutting system Kjellberg FF450 - Oxyfuel cutting process - Additional touch screen remote control attached to main drive - 3 Point fume exhaust system The SPC3000 is used by our eXperience Center and maintained by our best engineers at our headquarters in The Netherlands. The machine has a proven record and is used to profile pipes for clients in several high demanding industries f.i offshore, piping, structural steel and the vessel industry. A lot of special projects have been profiled on this machine.

Condition: new, Year of construction: 2025, functionality: fully functional, The CNC BAYKAL Hybrid Press Brakes combines all the benefits of both hydraulic and all-electric press brake systems into one. If you’re looking for press brakes that are fast, accurate, and energy-efficient, BAYKAL is the way to go. The CNC BAYKAL Hybrid Press Brakes can significantly save energy, save fuel, improve bending efficiency, reduce the risk of oil leakage, reduce installation costs, extend the service life of consumables, improve bending accuracy, reduce noise, and improve the working environment. The CNC BAYKAL hybrid press brakes system are designed with an individual electro-hydraulic servo drive system and servo pumps to control the for each of the left and right cylinders. The servo motor controls the output flow of the oil pump according to the program setting, and then controls the movement speed and position positioning of the slider, and there is no throttling phenomenon in the whole process. Therefore, all the energy output by the oil pump is supplied to the left-right oil cylinder. This control method does not have any energy loss, and the energy-saving effect is very prominent. With this system the hydraulics run on demand when the foot pedal is activated, rather than having a pump running continuously. This results in lower energy usage than a standard hydraulic machine as well as faster cycle times and extremely high accuracy. The flow and pressure of Y1 and Y2 oil cylinders are respectively controlled by two sets of servo bidirectional pump systems, and the oil in the upper chamber of the oil cylinder is directly pumped into the lower chamber of the oil cylinder through the oil pump to realize the lifting of the beam. The reverse rotation of the oil pump pumps the oil in the lower chamber of the oil cylinder directly into the lower chamber of the oil cylinder to realize the pressing and bending of the upper die. Rsdpforq D Niex Abhow Applicable between from 100 Tons to 1250 Tons, the synchronization of the left and right of the upper beam of the CNC BAYKAL hybrid press brakes is controlled separately by two sets of servo bidirectional pumps.

Condition: used, Technical details: welding current: 500 A Rodpfx Abowtctmohsw weight of the machine approx.: 129 kg dimensions L x W x H: 1,1x 0,7 x 1,2 m Control: Display for welding current with 2/4-cycle switchover, pulse, infinitely variable Cooling system: Water-cooled with frost protection Shielding gas: Solenoid valve without pressure reducer 3.0 m hose package Torch head: Gas-cooled Ground clamp with ground cable 2.5 m Wire feed: 4 roller drive with wire Ø 1.0/1.2 mm *

Year of construction: 2007, condition: ready for operation (used), A CNC profile drilling machine Voortman with a movable drilling cabin is available. Working height range: 30mm-1050mm, positioning speed: 40m/min, table width: 300mm, max. working width: 1800mm, support depth: 1500mm, tool stations: 5, max. travel speed: 40m/min, tool holder: SK40, drilling diameter range: 5mm-40mm, thread cutting range: M6-M30, working length: 16200mm. Documentation available. On-site inspection possible. Redpfxsxp Rb Is Abhsw

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, machine/vehicle number: 13-13, The BLOMAX 4 Blowmoulding machine is of the model 13-13. The machine has no defects and operates in excellent condition with full functionality. Power : 400V/150A/60000W Redpfx Abet Akgwehjw Year of construction : 2000

Condition: ready for operation (used), Year of construction: 2009, functionality: fully functional, saw blade diameter: 460 mm, cutting range round steel at 90°: 150 mm, working height: 1,030 mm, MSK 471 NA automatic straight cut circular saw for HSS and carbide saw blades Rsdpfxoubbw Ao Abhew Cutting range round up to 150 mm, square up to 140 mm Suitable for almost all profile shapes and solid material Automatic cut-off sorting by means of cut-off gripper Machine tested at KALTENBACH, wear parts replaced

Condition: like new (used), Year of construction: 2006, operating hours: 33,107 h, functionality: fully functional, Top machine from cleanroom production (pharmaceutical sector) - Equipped with 820 mm rotary table - Including GEKU Robot SR 500 ST (x=600, y=1400, z=2500 mm) - Only 33,107 operating hours - Safety enclosure / protective cage - Horizontal conveyor belt - Hardly any paint damage / almost as new in appearance - Fully operational The machine can be inspected under power by prior arrangement. Technical Specifications Manufacturer: Engel Model: V 330H/80V/130 Combi 2-Color with rotary table Serial number: 162036 Year of manufacture: 2006 Operating hours: 33,107 h Dimensions L/W/H: see drawing Weight: 10,600 kg Functionality: fully operational Condition: excellent Special features Control system: CC 200 Screw diameter: 25 / 22 mm Shot weight: 72 / 35 g Injection pressure: 2391 / 2066 bar Injection volume: 79 / 38 cm³ Clamping force: 1300 kN / 130 tons Tie bar spacing: tie-bar-less Ejector stroke / force: 61 kN / 100 mm Clamping unit: hydraulic Motor power: to be provided Heating capacity: to be provided Total power: to be provided The machine is immediately available from our warehouse in Hannover, Germany, and has been tested. Extras 2-component / 2-color machine Rotary table (820 mm diameter) Geku Robot SR 500 ST Safety enclosure / protective cage CC 200 control, German and English languages GEKU Robot Details SR 500 ST Control: Simotion Rodpfx Asub Umqebhsw X axis: 600 mm Y axis: 1400 mm (vertical) Z axis: 2500 mm (horizontal) A flip axis: SWM 45 C axis: Servo Gripper: SWS16 B axis: not available Warranty Warranty up to initial commissioning Loading/Shipping Free loading onto buyer's truck or free delivery against freight reimbursement from our warehouse in Hannover, Germany Financing – on request – leasing option Price on request

Year of construction: 2004, condition: good (used), machine/vehicle number: 2004-3-11A, - Feed of the milling head manually - Work table height adjustable via handwheel - Horizontal and vertical material clamping - Milling cutter diameter up to 250 mm - Max. milling height 150 mm - Max. milling depth 80 mm - Max. milling length 305 mm - Angle-adjustable stop, left and right 20 - 90° - Milling spindle speed 4500 rpm Redpfof E Higox Abhew - Drive 400 V, 3.2 kW - Compressed air connection 6 - 8 bar - Air consumption per working cycle 10 l - Pneumatic profile clamping - Table stand - Space required approx. W 1100 x H 1300 x D 700 mm - Weight approx. 200 kg