Eccentric press

Weingarten ARP 125

Condition: good (used), Make: OMERA Type: R4 / 12-2 Year: 1976 Table length : 1900 Table width : 1000 Steady arm throath HOR : 670 Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Specifications Metric US Standard There are no specifications for this machine (yet). Giedpjkvnumofx Af Ajt Dimensions (Estimate) Length 3000 mm Width 2200 mm Height 2500 mm Weight 2800 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: excellent (used), Year of construction: 2012, Model Amada HFE M2 220t 4m, 8 axis Press Brake Year 2012 Tonnage 220 tonnes Max. Bend Length 4280 mm Stroke Length 200 mm Approach Speed 1 - 100 mm/sec Bending Speed 1 - 10 mm/sec Return Speed 1 - 100 mm/sec Oil Capacity 195L Motor Power Weight 17450 Kg Dimensions Machine Length 5070 mm Machine Depth 2075 mm Giedpfsv S U Izsx Af Ast Machine Height 3085 mm Distance Between Side Frames 3760mm Beam width 180 mm Table height 960 mm Open Height 470 mm Throat Depth 420 mm

Condition: excellent (used), Year of construction: 2011, Prima Industrie Platino 1530 laser cutting machine only 4300 hours cutting hours Godpoivg Hgofx Af Asit This Prima Industrie Platino 1530 laser cutting machine 4,0kW CO2 was manufactured in Italy in the year 2011 and installed at the end of 12/2011. PRIMACH 20 L control unit.

Condition: used, Year of construction: 2003, pressure 250 t stroke 20 - 190 mm no. of strokes 25 - 140 /min throat 460 mm passage to the back 590 mm dayligth 690 mm table surface area 1500 x 880 mm hole in the table 950 x 250 mm table height over floor 900 mm ram surface 870 x 725 mm Gijdpfx Asvuun Tef Ast ram adjustment 120 mm power requirement 30,0 kW Weight 32,0 t dimensions of the machine ca. 2,34 x 2,38 x 3,99 m x m x m with infinitely variable drive, light guard (make Sick), hydraulic clutch/brake combination, hydraulic overload protection in ram, automatic stroke adjustment, motoric ram adjustment, pneumatic counterbalance in ram, fix table, drawing cushion in table (20 t), motoric centralized lubrication, operator's console with two-hand operation Width between the tie rods in front 940 mm Side passage 900 mm

Condition: new, Year of construction: 2025, Pressure blasting cabin DSK 11.11.30. Blasting chamber W=1050 D=1050 H=955mm. 1 TÜV-tested pressure vessel 30l with conical outlet funnel. 1 blasting medium dosing valve with blasting medium quantity regulation pneumatically controlled. 1 built-in closing cone with guide tube. 1 compressed air connection with pneumat. Shut-off valve and branch for control air. 1 pressure regulator to adjust the blasting pressure. 1 blasting hose DN19. 1 handpiece with boron carbide blasting nozzle Venturi 8mm. 1 pair of blasting gloves. Electrical height adjustment of the cabin for body-friendly posture. Memory position storage for 3 heights. Dust extraction filter 2000m³/h 2,2kW. Gisdpfjga Ehbox Af Ajt

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Giedpohlnzkjfx Af Aot Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Condition: used, Year of construction: 1970, machine/vehicle number: 120895, pressure:63 t throat:250 mm stroke:8 - 100 mm no. of strokes:120 Hub/min table::715 x 500 mm dayligth:330 mm ram adjustment:63 mm clamping plate:700 x 480 mm hole in the table:240 mm Hole in clamping plate:110 mm dimension of ram:450 x 280 mm weight of the machine ca.:5,5 t dimensions of the machine ca.:1,2 x 1,7 x 2,7 m hydraulic tilting single column eccentric press, tilting in 4 steps, opening to rear (325 x 500mm) and below (360x160mm) with central lubrication via hand pump, additional clamping plate 700 x 480 x 850 mm, two-hand operation, foot-trip operation possible, operating-mode selector for adjustment of continuous or single stroke, emergency cut-off, piece counter, various accessories Gjdpofx Hv Hjfx Af Asit

Condition: good (used), Year of construction: 2002, machine/vehicle number: V020113, operating hours: 43,000 h, AMADA MODEL HFT 8025 80 tons capacity x 2500 bending length hydraulic downstroking press brake complete with cnc control, Model Amada HFT 8025 downstoke CNC Press brake Year 2002 Tonnage 80 KN Controlled Axis Y1, Y2, X, R Max. Bend Length 2500 mm Open height 470 mm Approach Speed 100 mm/sec Bending Speed 1 - 10 mm/sec Return Speed 1-100 mm/sec Oil Capacity Motor Power 9kw Weight 5750 kg Bed Length 2500 mm Bed Width 180 mm Open Height 470 mm Gijdpfx Aouwktnof Aet Throat Depth 420 mm CNC Control

Condition: used, Year of construction: 1980, machine/vehicle number: A-07/471A, sheet width - max.:130 mm straightening roll diameter:40 mm :5 :2+2 sheet thickness - min.:0,4 mm sheet thickness - max.:3,5 mm weight:0,4 t Gjdpfx Afecxxx Ro Ajit dimensions of the machine ca.:0,6x0,65x1,15 m with integrated, stepless adjustable Vari-drive, reversing, operating-mode switch for manual and automatic operation, introduction roller cage, position indicator of straightening rolls via analogue display, adjustment of straightening rollers via hand wheels, automatic swivel arm control, very good condition

Year of construction: 1993, condition: used, TYPE : DEA 400/2000 Type YEAR : n.d. Year MAXIMUM SLEDGEHAMMER PRESSURE : TON. 400 Ram capacity SLIDING STROKE : mm. 1,100 Giedpfx Afoihf R Uj Aot Slide strok MAX VERTICAL LIGHT : mm. 1,600 Max shut height TABLE DIMENSIONS : mm. 2,000 x 1,600 Table size RAPID SPEED : mm/sec 650 Fast stroke TABLE PRESS CAPACITY : TON. 160 Cushion capacity PRE-MILER stroke : mm. 400 Cushion stroke HEIGHT ABOVE GROUND : mm. 5,800 Ground up to floor FRONT LIGHT : mm. 3,400 Distance btw uprights LATERAL LIGHT : mm.1,600 Lateral window