Surface grinding machine

ABA Z&B SCHLEIFMASCHINEN GMBH ECOLINE 1206A

Condition: excellent (used), Year of construction: 2022, CNC Surface, Profile, and Deep Grinding Machine ELB-Schliff smartLine BD15 KXT XC Control: Xpress Cube Year of manufacture: 2022 Grinding width: 600 mm Grinding length: 1,500 mm Grinding height: 500 mm Grinding wheel diameter: 400 mm Table load: 1,200 / 625 kg Spindle drive: 10 – 52 kW Psdpfx Akoyk Tb Uoropr Spindle taper: 60 / 75 mm Speed range: 1,450 – 3,500 rpm Accessories: Belt filter system Coolant mist extraction system type VMN-V12 Balancing system Magnetic chuck

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC Ppsdpfewp Rqfox Akrer • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: good (used), Year of construction: 2017, In this offer you buy used office furniture, which is in good condition. They were delivered in 2017 and are generally in very good condition, since little used. Items for sale: Ppodpfx Aoiiv Ikokrer We also offer workplace sets for 450€. 1x desk - Manufacturer: FM - 160 x 80 x 76 (stepless height adjustable 68cm to 76cm) - gray top - aluminum frame 1x office chair "Dauphin MagicShape elan - armrests - completely adjustable - cover polo grey/black 1x mobile pedestal - Manufacturer: FM - 43,4 x 80 x 59 - one material drawer - 3 steel drawers with softclose - lockable incl. key Desks: - Approx. 10x desk from the manufacturer FM 1600 x 800 x 680 to 760 (infinitely height adjustable) in the color light gray. Frame made of aluminum - Approx. 12x folding table (can be used as a desk) 1600 x 800 x 720 on castors, in the color light gray. Aluminium frame - Approx. 2x round meeting table 1000mm diameter in the color light gray. Aluminium frame - Approx. 4x high table 1600 x 800 x 1300 in the color arctic white. Frame in white aluminum Chairs: - Approx. 10x Dauphin swivel chair MagicShapeS elan with armrests and fully adjustable. Fabric cover Polo black, base plastic black - Approx. 44x Interstuhl Hero 550H cantilever chair with armrests. Upholstery in ruby red color. Metal frame chrome-plated. - Approx. 52x Interstuhl Hero 550H cantilever chair with armrests. Upholstery in the color ocean blue. Metal frame chrome-plated. - Approx. 10x Interstuhl Kinecticis5 710K bar stool with footrest. Upholstery in the color black. Frame in silver color. - Approx. 16x Interstuhl Kinecticis5 710K bar stool with footrest. Upholstery in the color ocean blue. Frame in silver color - 12x Interstuhl Kinecticis5 710K bar stool with footrest. Upholstery in the color red. Frame in the color silver - 16x Interstuhl Kinecticis5 710K bar stool with footrest. Upholstery in the color ruby red. Frame in the color silver Storage space: - Approx. 16x FM 434 x 800 x 590 mobile pedestal with one material drawer and 3 steel drawers. Body completely in the color light gray. Handles made of aluminum meeting table with 4 conference chairs - 750,-€ net high table with 6 bar stools - 1500,-€ net Prices may vary slightly depending on the quantity purchased. We will be happy to prepare a suitable offer for you. You can also purchase each piece of furniture separately. Condition: This offer is used furniture, which may show signs of use (minor scratches or yellowing). Packing and shipping: You are welcome to look at everything during our business hours. Please make an appointment for this! Seaworthy packing and worldwide shipping is possible on request! For more information you can of course also contact us personally.

Condition: good (used), functionality: fully functional, Year of construction: 2006, laser power: 4,000 W, AVAILABLE AT SHORT NOTICE: TRUMPF Trumatic L 3030 - 4 kw - Year 2006 TECHNICAL DATA: Make: TRUMPF Type: L 3030 - 4 kw Year of manufacture: 2006 Working area: 3,000 x 1,500 x 115 mm Control: Siemens Sinumerik 840 D Laser power: 4,000 watts Max. Sheet thickness mild steel: 20 mm Max. Sheet thickness stainless steel: 15 mm Max. Sheet thickness aluminum: 10 mm Operating hours: NC Machine regularly serviced by TRUMPF! Transmitter tube: new 2024 TASC laser control: new 2022 Driver stage: replaced 2018 Magnetic bearing electronics: new 2016 STANDARD EQUIPMENT: - Closed machine frame with integrated laser unit Laser unit: TLF 2000 high-frequency excited CO2 laser, maintenance-free turboradial blower, mirror telescope, cooling unit, logbook function - Automatic pallet changer - Longitudinal conveyor belt for small parts/waste - Drives: maintenance-free three-phase servomotors - Cutting head quick-change device - Laser cutting head with 5" lens and laser cutting head with 7.5" lens - Programmable cutting gas pressure setting - APC capacitive height control and process control - AutoLas Plus automatic focus position adjustment - Laser power control - Position laser diode - HI-LAS high-pressure cutting - Fast processing with SprintLas - ContourLas for the production of small holes - PMS plasma sensor technology - Automatic sheet edge detection - Programmable power cycles - Microweld Ppedpfx Ajuthz Tekror - Automatic switch-off - Work area lighting - Sinumerik 840D control system: open control system on PC basis, simple operation, online help, integrated e-shop, diagnostic functions, maintenance logbook, technology data, teleservice - Workshop programming ToPs 100 lite - Safety: multi-beam light barriers, beam guidance fully encapsulated and ventilated, monitoring system, multi-chamber extraction and compact dust extractor, protective cabin - 3.5" floppy disk drive - TFT color screen - Electrical equipment: Voltage 400 V / 50 Hz - Paint finish: Standard RAL 9002/5010 EXTENDED EQUIPMENT: - TLF 4000 laser incl. lens monitoring sensors - PCS Process Control System

Condition: good (used), Year of construction: 2004, Machine is good working condition. Ppjdpfxsyufn Ij Akrjr Control unit Heidenhain TNC 530 Parts shown by hand not come.

Condition: used, Year of construction: 2007, machine/vehicle number: 001669, Lg 33121 Single side decoiler ARKU AH 3000/ST-M year of manufacture 1995 belt width max. 600 mm load capacity max. 3.000 kg coil outer diameter max. 1.800 mm Spreading hydraulic Pressing arm hydraulic Decoiler with auxiliary drive and brake coiler chair fixed + reel traversing device with: Lg 33221 High performance belt leveler LORENZ BRM 50/620.9 year of manufacture 2007 Machine no. 001669 passage width max. 620 mm number of straightening rolls 9 Straightening roll diameter 50 mm Pedpjhigmbsfx Akropr Material density 0.7 to 6.0 mm Straightening rolls supported several times against deflection All rolls driven by transfer gearboxes and cardan shafts. cardan shafts. Used, in as-is condition from stock, available immediately. On request with overhaul. Delivery time by agreement. Further data shortly or on request.

Condition: new, Year of construction: 2025, machine/vehicle number: 732335740, Mobile jaw crusher on crawler track Diablo crusher is the most modern machine in the category with 30 tons. It is equipped with the latest control and operation systems of the latest generation, it is simple and user-friendly, and environmentally friendly to boot. The HCS (Hydraulic Crushing System) control system actively supports the automatic operation of the machine, guarantees the highest profitability in terms of maintenance costs and productivity, making it incomparable. The structural reinforcement between the frame and the crusher gives the machine maximum robustness to to stresses and strains. The particular design of the supporting structure guarantees excellent access to all parts of the machine during maintenance operations. Production capacity: approx. 220 TO/H Patented HCS system Proportional distributor with \"Load Sensing \" for an optimization of the system and a reduction of fuel consumption by approx. 30%. Pre-screening optional gap size hydraulically adjustable also during crushing operation fast blocking system with wedges and folding cylinders unloading height 3000 mm dust extraction system tank pump magnetic separator warranty 1 year to max. operating hours from the start of operation of the equipment Technical data: Jaw crusher 1000 x 600 mm Ppjdpfshd I Sxjx Akrjr crushing gap from 40 to 170 mm Feed hopper 4m³ - 1820 x 3700 mm Grizzly feeder version 900 x 3300 mm Main conveyor belt 800 x 9600 mm 4 cylinder constant speed diesel engine 82 HP/60 KW, exhaust stage V Control panel Chain drive 400 x 2920 mm Weight: kg transport length 12500 mm Transport width:2530 mm Transport height 3150 mm Further information Purpose: construction, General condition: very good, Technical condition: very good, Visual condition: very good, Delivery conditions: EXW,

Condition: used, Year of construction: 2008, turning diameter 1000 mm swing diameter 1250 mm turning height 500 mm control Siemens Sinumerik 840 D Workpiece spindle flange diameter 520 mm work piece spindle speed range 0-440 U/min total power requirement 75 kW weight of the machine ca. 25 t dimensions of the machine ca. 5100 x 3034 x 4500 mm With grinding spindle Table travel: - Z1/Z2 axis 1000 mm, - X1/X2 axis approx. 1300 mm Pedpfxow Rgcfs Akrspr Table speed continuously adjustable: - Z axis 0–30 m/min, - X axis 0–50 m/min - Feed speed continuously adjustable 0.01–15 mm/min - Feed dependent on stroke 0.0005–0.1 mm - Workpiece spindle positioning C axis Equipment/accessories: - Grinding spindle - Kaiser dresser - Tool measuring probe - Filter system - With flushing nozzle connections - 2 Capto holders - 1 set of jaws for chuck - technical documentation

Year of construction: 2008, condition: ready for operation (used), Sanding range: 2000x900mm, transverse movement: 875mm, longitudinal movement: 2450mm, distance table to spindle center: 845mm, magnetic clamping plate dimensions: 2000x800mm, max. table load: 2.3t, feed rate longitudinal axis: 1000-30. 000mm/min, feed transverse axis: 0,01-2000mm/min, feed vertical axis: 0,001-1500mm/min, grinding wheel dimensions: 500x100x203,2mm, power grinding spindle motor: 22kW, length: 6800mm, width: 3450mm, weight: 13t. On-site inspection is possible. Pjdpfjuyk N Iox Akrjpr

Condition: used, Year of construction: 1994, turning diameter 570 mm turning length 2000 mm control Sinumerik 805 Siemens swing diameter over face slide 365 mm main spindle speeds: 3-2.500 U/min drive of main spindle 15/19 kW Ppsdpfeu Sbkgjx Akror spindle bore 62 mm spindle head DIN 55027 No.8 tailstock taper MT 5 quill stroke 190 mm pinole diameter 80 mm feed range - long. and cross 0,01-50 mm/u total power requirement 50 KVA weight of the machine ca. 5 t dimensions of the machine ca. m