Arburg Allrounder 420S 800-150 (2001)

Arburg 420 S 800-150

Condition: good (used), Year of construction: 2000, Arburg 420C 1000-350 Clamping force: 100 tons Distance between tie bars: 420 x 420 mm Cjderthkuepfx Agksgp Mold plattens: 570 x 570 mm Screw diameter: 35 mm Injection volume: 230 cm3 Shot weight: 127 g New temperature control board ARB 777 (cost 2.750€)

Condition: new, Year of construction: 2023, functionality: fully functional, machine/vehicle number: 61037337, clamping force: 800 kN, screw diameter: 30 mm, displacement volume: 113 cm³, injection pressure: 2,500 bar, injection weight: 103 g, mold height (min.): 400 mm, ejector force: 22,600 N, ejector stroke: 150 mm, opening stroke: 900 mm, total length: 3,960 mm, total width: 1,480 mm, total height: 2,020 mm, overall weight: 3,550 kg, heating capacity: 10.9 kW (14.82 HP), drive type: Hadraulisch, clear span: 470 mm, tool weight: 10,00,000 g, Injection molding machines direct from the manufacturer! As the manufacturer KraussMaffei, we offer you our tested and flexible stock machines here: The fully hydraulic CX series offers a particularly compact, efficient and flexible two-platen machine. The very compact two-platen concept with cantilevered clamp offers generous space for peripheral equipment and excellent accessibility. Efficient and intelligent energy management with BluePower servo drive continues to provide a powerful basis for the highest demands and the right solution for every application. TECHNICAL DATA: KM 80 / 380 CX G06 (order 38655610) CONTROL  MC 6 with 21.5" TFT color screen with multi-touch functions CLAMPING UNIT  Clamping force kN 800  Mold opening force, max kN 55  Clear width (h x v) mm 470 x 420  Clamping platen (h x v) mm 670 x 670  Tool installation height min. - max. mm 400 (increased by 150 mm)  Opening width mm 900 (increased by 150 mm)  Mold opening stroke max. mm 500  Hydraulic ejector drive  Ejector stroke mm 150  Ejector force forwards/backwards kN 22.6 / 9.8  Ejector speed forwards/backwards mm/s 760 / 800  Max. Mold weight kg 1000 SPRING UNIT  Screw diameter / type mm 30 / standard (customization possible)  Effective Ls/D ratio 26.7  Injection pressure bar 2500  Stroke volume cm³ 113  Shot weight at max. stroke for PS g 103  Injection speed mm/s 100  Injection flow rate cm³/s 71  Screw drive/speed 1/min 295  Plasticizing flow (standard) g/s 12.3  Nozzle contact force kN 50 ELECTRICAL PARAMETERS Connected load kW 15.0  Installed heating capacity kW 10.9  Power supply V / Hz 380 / 50 3 phases with neutral conductor WEIGHT AND DIMENSIONS  Net weight with switch cabinet t 3.55  Length x width x height m 3.96 x 1.48 x 2.02 ADDITIONAL EQUIPMENT  Low-wear plasticizing  BluePower fully insulated plasticizing cylinder Cedjud N Hdopfx Agksgp  Open nozzle  1 additional temperature control point for nozzle heating  Air valve 1 - compartment (BWAP)  Pneum. Control hot runner valve gate 1 - compartment  Hydraulic core pull 1 - compartment (BWAP)  Euromap interface handling E18, E63  Euromap interface (central computer) E67, E77  Adaptive Process Control (APC)  Injection stamping circuit  Graphic analysis package The machine is located in our factory in Parsdorf and is available at short notice. Further additional options can be offered on request. We look forward to your inquiry.

Condition: new, Year of construction: 2023, functionality: fully functional, machine/vehicle number: 61036940, clamping force: 1,600 kN, screw diameter: 50 mm, displacement volume: 393 cm³, injection pressure: 1.892 bar, injection weight: 358 g, mold height (min.): 200 mm, ejector force: 33,000 N, ejector stroke: 100 mm, opening stroke: 950 mm, installation height: 500 mm, total length: 5,650 mm, total width: 1,820 mm, total height: 1,950 mm, overall weight: 9,700 kg, heating capacity: 15.5 kW (21.07 HP), drive type: Vollelektrisch, clear span: 570 mm, tool weight: 6,00,000 g, Injection molding machines direct from the manufacturer! As the manufacturer KraussMaffei, we offer you our tested and flexible stock machines here: The basic injection molding machine, precisionMolding, offers the perfect entry-level solution for all-electric injection molding, enabling you to react quickly and innovatively to market requirements. It combines high performance, simple operation and short delivery times. It can be used in a wide range of applications, e.g. in the packaging industry, the electrical and electronics industry, medical technology and the automotive industry. Your benefits: - Optimized price-performance ratio for a wide range of applications - High energy efficiency thanks to all-electric machine concept - Realization of demanding delivery times thanks to basic machine concept with a wide range of options TECHNICAL DATA: KM 160 / 750 PA G01 (order 38670011) (machine no.: 61036683, new, year of manufacture 2013) CONTROL  MC P1 with 15" TFT color screen with multi-touch functions CLAMPING UNIT  Clamping force kN 1600  Mold opening force, max kN 120  Clear width (h x v) mm 570 x 520  Clamping platen (h x v) mm 770 x 720  Tool installation height min. - max. mm 200 - 500  Opening width mm 950  Mold opening stroke max. mm 450  Ejector drive electric  Ejector stroke mm 100  Ejector force forwards/backwards kN 33 / 33  Ejector speed forwards/backwards mm/s 300 / 300  Max. Mold weight kg 1200 SPRING UNIT  Screw diameter / type mm 50 / standard  Effective Ls/D ratio 20.2  Injection pressure bar 1892  Stroke volume cm³ 393  Shot weight at max. stroke for PS g 358  Injection speed mm/s 200  Injection flow rate cm³/s 393  Screw drive/speed 1/min 267  Plasticizing flow (standard screw)4) g/s 36.5  Nozzle contact force kN 42 ELECTRICAL PARAMETERS  Connected load kW 31.2  Installed heat output kW 15.5  Power supply V / Hz 400 / 50 3 phases with neutral conductor WEIGHT AND DIMENSIONS  Net weight with switch cabinet t 9.7  Length x width x height m 5.65 x 1.82 x 1.95 ADDITIONAL EQUIPMENT  Low-wear plasticizing  BluePower fully insulated plasticizing cylinder  Open nozzle  Air valve 1 - fold (BWAP)  Pneum. Control hot runner valve gate 1 - compartment  Electrical interface pneum. Cascade 4-fold  Euromap interface handling E18 + E67  Euromap interface (central computer) E67, E77  Water battery 4 - compartment  Electrical preparation for hydraulic auxiliary unit  Automatic central lubrication  Adaptive Process Control (APC)  Injection compression molding circuit  Graphic analysis package Cgedpfxsugfw De Agkjp  Swivel device for injection unit The machine is located in our factory in Parsdorf and is available at short notice. Further additional options can be offered on request. We look forward to your inquiry.

Condition: good (used), Year of construction: 2003, operating hours: 1,06,864 h, clamping force: 1,300 kN, screw diameter: 35 mm, The machine was very well looked after, service and maintenance were always carried out on time. Good condition, fully functional Still in use until week 11 Further service reports and documents available Cedpfjrp Dyrjx Agkegp Technical data: YEAR OF MANUFACTURE: 2003 Automatic operation: 106,864 h Clamping force: 1300 kN Screw diameter: 35 mm Screw stroke: 180 mm Closing force: 50 kN Opening stroke: 500 mm distance between ejector plates: 750 mm Ejector force: 40 kN Advance package - VE561/20 LGS Position-regulated screw with control valve on the injection unit for particularly high dynamics and reproducibility of the injection process, the back pressure is regulated, the nozzle contact force is manually adjustable - VE 557/00 AES Energy-saving system for automatic performance optimization and corresponding energy energy saving through infinitely variable adjustment of the pump drive speed to the respective power requirement of the spraying cycle - VE 460/00 ED Electromechanical metering drive via a speed-controlled three-phase asynchronous motor to increase productivity through simultaneous movement, through gentler material preparation and corresponding energy savings compared to hydraulic dosing On request, loading and transport (Europe-wide) can be organized for an additional charge. Prices plus VAT Viewing possible by appointment. Please contact us, our team will be happy to help you. Trade-in or exchange possible! Machines purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MUCH MORE. Do you need a high-quality but inexpensive metalworking machine for your production? Or do you want to sell yours? For further information or contact options, please visit our website

Condition: like new (used), Year of construction: 2017, operating hours: 16,000 h, functionality: fully functional, 1,0 St. gebr. Zweikomponenten Spritzgießmaschine Hersteller: ARBURG Cgjdpfxev S E Dgo Agkep Typ: 720A3200-800/70 Baujahr: 2017 Schließkraft: 320 Tonnen Holmabstand 720 x 720 mm Einbauhöhe min. /max.: 300 - 800 mm Öffnungsweg: 600 mm Schnecken DN 1: 50 mm Max. Hubvolumen: 392 cm³ Spritzteilgewicht in PS: 359 g Schnecke DN 2: 22 mm Max. Hubvolumen: 34 cm³ Spritzteilgewicht in PS: 31 g Steuerung: Selogica Technische Ausstattung anfordern.

Condition: ready for operation (used), Year of construction: 2001, clamping force: 500 kN, injection pressure: 2.2 bar, For sale is an injection molding machine of the brand Arburg and the type 320 S 500-150 The machine is in working order Technical data - Clamping force: 500 kN - Distance between the tie bars: 320 mm x 320 mm - Mold thickness: 225-350 mm - Clamping platen dimensions: 445 mm x 445 mm - Opening of the clamping platen: max. 550 mm - Screw diameter: 30 mm - Injection pressure: 2 200 bar - Weight: 2 250 kg Cedjqmn Egopfx Agksgp On request, for an additional charge, dismantling, loading & transport can be organized for you throughout Europe Prices plus VAT Viewing possible by appointment. Contact us, our team will be happy to help you. Trade-in or exchange possible! Machines purchase / sale BUYING / SELLING PRODUCTION & METALWORKING MACHINES AND MUCH MORE. Do you need a high-quality but inexpensive metalworking machine for your production? Or do you want to sell yours? For further information or contact options, please visit our website

Condition: good (used), Year of construction: 2001, Ref. no.: 18404 Hersteller: ARBURG Type: 420C-1300-350 Year of construction: 2001 Clamping unit Clamping force: 130 ton Opening stroke: 500 mm Distance between tie bars: 420 x420 mm Mould height min.: 250 mm Opening width: 750 mm Platen size (h x v): 605 x 605 mm Injection unit Screw diameter: 45 mm Codpswm I A Tefx Agkjgp Injection volume: 230 cm³ Shot weight: 210 g Injection pressure: 1670 bar Measurements and weight Dimensions: 4,68 x 1,3 x 2,2 m Machine weight: 4080 kg Additional information & extras Core pull: 1 pcs

Condition: excellent (used), Year of construction: 2000, operating hours: 46,000 h, functionality: fully functional, machine/vehicle number: 180316, clamping force: 1,000 kN, screw diameter: 35 mm, clearance between the columns: 420 mm, Fully functional plastic injection molding machine with associated documentation and diskettes. Csdpfx Aov N D Rasgksgp The machine operated in clean production. The machine was injection molded with LDPE material, so the tip and screw are in first-class condition. Every 2 years, the pressures were checked and confirmed by an Arburg authorized service.

Year of construction: 1998, condition: ready for operation (used), Five identical Arburg injection molding machines are available. Clamping force: 800kN, column distance: 420mm/420mm, installation height: 250mm, platen distance: 700mm, nozzle diameter: 45mm, weight: approx. 3800kg, control: Selogica 3.020. All machines include temperature control unit and conveyor belt. Documentation available. The machines are in storage. On-site inspection is possible. Cgedpfx Aeviv Dfsgkjp

Condition: good (used), Year of construction: 1998, Screw diameter: 25 mm Clamping force: 25 tons Csdpfxovxh Iuj Agkjgp Opening stroke: 350 mm Weight: 2,900 kg Immediately available from stock